IllustrationHEAD GASKET HAS BEEN LEAKING FOR ABOUT TWO WEEKS.*AK
1995 Dodge Stratus
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 1995 Dodge Stratus do not stand out strongly from the model-year median of 168.
About this comparison →How this year compares
Owner complaints by model year
Compare all Stratus years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 25 of 318 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine And Engine Cooling. Review the 106 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes, Hydraulic. Review the 56 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 55 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
28 crash reports13 fire reports19 injury reports
What owners actually said
318 reportsTHE TRANSAXLE OFTEN SLIPS AND FAILS TO SHIFT INTO DRIVE. EVENTUALLY, THE TRANSMISSION HAD TO BE REPLACED. *NLM
THE SEAT BELT BUCKLE CAME APART ON THE DRIVER SIDE REAR SEAT BELT. THE CONSUMER STATED THAT IT WAS A DEFECTIVE CINCH PLATE. *NLM
THE VEHICLE WAS PARKED, WHEN THE ENGINE CAUGHT ON FIRE. *JB PRIOR TO FIRE, VEHICLE WAS RUNNING ROUGH AND USED A LOT GAS. DIRTY FUEL RAIL WAS REPLACED AND 4 INJECTORS THAT WERE PLUGGED. CONSUMER IS AWARE OF RECALL 96V00600 RELATING TO THIS CONDITION. *TT
MY WIFE COMPLAINED OF BRAKE PEDAL TRAVEL FURTHER THAN NORMAL. UPON INVESTIGATION, I DISCOVERED THAT ONE OF THE BOLT STUDS THAT HOLDS THE MASTER CYLINDER TO THE POWER BRAKE BOOSTER WAS BROKEN OFF AND MISSING. THE MASTER CYLINDER WAS PUSHED OUT OF THE BOOSTER TO ABOUT A 30 DEGEREE ANGLE. THE REMAINING STUD WAS STILL IN PLACE BUT B…
Read full complaint
MY WIFE COMPLAINED OF BRAKE PEDAL TRAVEL FURTHER THAN NORMAL. UPON INVESTIGATION, I DISCOVERED THAT ONE OF THE BOLT STUDS THAT HOLDS THE MASTER CYLINDER TO THE POWER BRAKE BOOSTER WAS BROKEN OFF AND MISSING. THE MASTER CYLINDER WAS PUSHED OUT OF THE BOOSTER TO ABOUT A 30 DEGEREE ANGLE. THE REMAINING STUD WAS STILL IN PLACE BUT BENT BADLY TO ONE SIDE. IF THERE HAD BEEN A PANIC STOP REQUIRED, I FEEL THAT THE MASTER CYLINDER COULD HAVE SEPARATED FROM THE BOOSTER, WITH THE EFFECT OF HAVING NO BRAKING EFFECTIVENESS. THIS COULD HAVE RESULTED IN A SERIOUS ACCIDENT OR FATALITY.*JB
THE CAR LEAKS OIL BADLY, I SEE ITS HAD BEEN A OIL RECALL UNDER/ THE ENGINE CYLINDER HEAD OIL GALLERY PLUG/ IT SMOKES THE HOOD, LEAKS WATER OUT OF TAIL PIPE: 1995 DODGE STRATUS RECALL#96V00600/ THE DEALER KEEPS TELLING ME THERE ISN'T ANY RECALLS ON MY VEHICLE. IF THIS PROBLEM PERSIST ITS GOING TO START A FIRE,,,,,,,,,,,ITS A …
Read full complaint
THE CAR LEAKS OIL BADLY, I SEE ITS HAD BEEN A OIL RECALL UNDER/ THE ENGINE CYLINDER HEAD OIL GALLERY PLUG/ IT SMOKES THE HOOD, LEAKS WATER OUT OF TAIL PIPE: 1995 DODGE STRATUS RECALL#96V00600/ THE DEALER KEEPS TELLING ME THERE ISN'T ANY RECALLS ON MY VEHICLE. IF THIS PROBLEM PERSIST ITS GOING TO START A FIRE,,,,,,,,,,,ITS A SAFETY HAZARD IN MY EYE AND MANY OTHER AUTO REPAIR SHOPS,,,,
THIS IS THE SECOND HEAD GASKET FAILURE SINCE I HAVE PURCHASED THE CAR. DT
I ATTEMPTED TO USE THE JACK TO CHANGE A TIRE AND THE JACK FAILED. THE ALUMINUM HOUSING IN WHICH THE SCREW TURNS IS VERY POROUS (I.E. LOTS OF AIR BUBBLES IN THE ALUMINUM CASTING).**** DIMS 11 IVOQ ENTRY POSTED AFTER 12/12/02 TURN-OVER TO ARTEMIS****769754. *AK *JB
CONSUMER STATES THAT THE CORRECT STRUTS FOR VEHICLE ARE NO LONGER AVAILABLE. CONSUMER STATES OVER TIME THE FRONT END MAY FALL. *AK THE CONSUMER STATED THAT THE STRUTS AVAILABLE WERE UNSATISFACTORY SINCE IT IS KNOWN TO CAUSES UNNECESSARY WEAR TO FRONT END PARTS RESULTING IN MISALIGNMENT OF THE VEHICLE. *YH
I CANNOT GET THE PROPER FRONT STRUTS THE ONES DODGE SELLS ARE UNSAFE TO PUT ON. MY MECHANIC AND A CERTIFIED DODGE MECHANIC SAID THAT IF I PUT THESE ON IT WOULD NOT BE POSSIBLE TO KEEP THE CAR LINED UPAND IT COULD CAUSE IMPROPER TIRE WEAR OR NOT PUT PRESSURE IN THE WRONG PLACES IN THE FRONT END POSSIBLY CAUSING AN UNSAFE CONDITIO…
Read full complaint
I CANNOT GET THE PROPER FRONT STRUTS THE ONES DODGE SELLS ARE UNSAFE TO PUT ON. MY MECHANIC AND A CERTIFIED DODGE MECHANIC SAID THAT IF I PUT THESE ON IT WOULD NOT BE POSSIBLE TO KEEP THE CAR LINED UPAND IT COULD CAUSE IMPROPER TIRE WEAR OR NOT PUT PRESSURE IN THE WRONG PLACES IN THE FRONT END POSSIBLY CAUSING AN UNSAFE CONDITION.I WAS TOLD THAT 95 STRATUS AND SEBRINGS ARE THE ONLY ONES WITH THIS PROBLEM. THEY MUST HAVE RUN OUT OF THE ORIGINAL STRUTS SO THEY PUT APAPER IN THE STRUT BOX SAYING TO TURN THE RUBBER SPRING ISOLATER AROUND.IF YOU DO THIS EVERYTHIG IS ANGELED WRONG AND THE RUBBER ONLY HALF SITS ON THE SPRING. THIS IS REDICULOUS.YOU COULD NEVER KEEP THE CAR LINED UP. MY MECHANIC SAID THERE IS NO WAY HE WOULD BE RESOSIBLE PUTTING THEM ON. IF DODGE WANTS TO SIGN A PAPER SAYING THEY WILL BE RESONSIBLE FOR ANY ACCIDENTS OR BE RESONSIBLE FOR FRONT END MISALIGMENT OR PARTS FAILURE THEN I WILL PUT THEM ON. I SHOULD NOT BE FORCED INTO PUTTING AN UNSAFE PART ON MY CAR.DODGE CHANGED EVERYTHIG ON THE FRONT END IN 96 AND THEY MUST HAVE FINALLY RUN OUT OF THE PROPER STRUTS SO INSTEAD OF TOOLING UP AND MAKING MORE OF THE RITE ONES THEY ARE TRYING TO GET AWAY WWITH THIS. IF YOU HAVE ANY MECHANIC LOOK AT THIS HE WILL TELL YOU HOW WRONG IT IS. IT MAKES ME WONDER HOW MY 95 DODGE STRATUS AND SEBRINGS OUT OUT ON THE ROAD RUNNING THIS UNSAFE AND POSSIBLY HAZADOUS PARTS. THIS SHOULD BE INVESTIGATED ASAP.BECAUSE THIS IS SO WRONG. THIS CAR HAS A RECALL FOR TYHE FRONT END ALREADY. THIS SHOULD BECOME ANOTHER RECALL SO THEY CAN MAKE SURE THESE MODEL CARS HAVE THE SAFE AND PROPER STRUTS ON THE FRONT.IF YOU HAVE SOMEONE TRY TO PUT THESE STRUTS ON THEY WOULD TELL YOU HOW WRONG IT IS. ALL I WANT IS THE SAFE PARTS FOR MY CAR.
Official recalls
704V021000 · Power Train:automatic Transmission:lever And Linkage:floor Shift
Jan 13, 2004
ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.
Consequence & remedy
Consequence: EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.
Remedy: DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
98V183000 · Power Train:automatic Transmission:park/neutral Start Interlock Switch
Aug 6, 1998
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.
Consequence & remedy
Consequence: IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL BE NONFUNCTIONAL.
Remedy: DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.
98V063000 · Seat Belts:front:anchorage
Mar 20, 1998
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE REAR SEAT BELT ANCHOR DOES NOT ACHIEVE THE LOADING REQUIRED BY FMVSS NO. 210, "SEAT BELT ASSEMBLY ANCHORAGES."
Consequence & remedy
Consequence: FAILURE OF A SEAT BELT ANCHOR CAN RESULT IN THE LOSS OF SEAT BELT PROTECTION, WHICH COULD LEAD TO SERIOUS INJURY OR DEATH IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL INSPECT THE REAR SEAT BELT OUTBOARD ANCHOR FLOOR ATTACHMENTS FOR PROPER POSITIONING. IF THE ANCHOR WAS IMPROPERLY ORIENTED, THE ORIENTATION WILL BE CORRECTED.
97V201000 · Suspension:front:control Arm:lower Ball Joint
Nov 13, 1997
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.
Consequence & remedy
Consequence: SEPARATION OF THE BALL JOINT COULD CAUSE A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE CRASH.
Remedy: DEALERS WILL INSPECT THE BALL JOINT END HOUSING COVER SEAL FOR LEAKAGE WITH A HIGH PRESSURE AIR TESTER AND THE RUBBER BOOT WILL BE VISUALLY INSPECTED FOR DAMAGE. IF THE COVER SEAL LEAKS OR THE BOOT IS DAMAGED, THE LOWER CONTROL ARM WILL BE REPLACED.
96V075000 · Service Brakes, Hydraulic:foundation Components:master Cylinder
May 3, 1996
THE BRAKE MASTER CYLINDER CAN LEAK BRAKE FLUID DUE TO A DAMAGED DOUBLE LIP REAR PISTON SEAL.
Consequence & remedy
Consequence: BRAKE FLUID LEAKAGE CAN RESULT IN DIMINISHED EFFECTIVENESS OF ONE HALF OF THE SPLIT BRAKE SYSTEM. THE INSTRUMENT PANEL WARNING LIGHT(S) WILL SIGNAL SYSTEM IMPAIRMENT PRIOR TO PARTIAL BRAKE SYSTEM LOSS.
Remedy: DEALERS WILL REPLACE THE REAR BRAKE MASTER CYLINDR PISTON ASSEMBLY.
96V074000 · Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
May 2, 1996
CORROSION OF THE ABS HYDRAULIC CONTROL UNIT CAN CAUSE THE SOLENOID VALVES TO STICK IN THE OPEN POSITION.
Consequence & remedy
Consequence: IF EITHER FRONT WHEEL VALVE STICKS, THE VEHICLE WOULD SWERVE FROM A STRAIGHT STOP WHEN THE BRAKES ARE APPLIED.
Remedy: DEALERS WILL INSTALL A PLATE AND SILICONE GREASE INJECTED INTO THE SOLENOID CAVITY TO ELIMINATE THE POTENTIAL FOR THIS CONDITION.
96V006000 · Engine And Engine Cooling:engine:gasoline
Jan 11, 1996
IN CERTAIN VEHICLES, THE ENGINE CYLINDER HEAD OIL GALLEY PLUG DOES NOT SEAL PROPERLY AND ENGINE CYLINDER HEAD OIL IS NOT ADEQUATELY RETAINED.
Consequence & remedy
Consequence: INADEQUATE SEALING AND RETENTION OF THE PLUG CAN RESULT IN OIL LEAKAGE WHICH COULD CAUSE A FIRE IN THE ENGINE COMPARTMENT.
Remedy: DEALERS WILL INSTALL AN EXPANSION PLUG AND RETAINING BRACKET OVER THE CYLINDER HEAD OIL GALLEY PLUG.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
5EA03011 · Auto Trans IGNITION-PARK Interlock
Opened Jul 17, 2003 · Closed Jan 30, 2004
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Additional source detail variants (2)
Power Train:automatic Transmission
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
DP03002 · Steering Column Separation
Opened May 7, 2003 · Closed Jul 22, 2003
Status: closed (inferred from source dates) · Steering:column
MR. LARRY A. SACKEY SUBMITTED A PETITION TO THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION (NHTSA) BY LETTER DATED APRIL 18, 2003, REQUESTING THAT NHTSAFURTHER INVESTIGATE THE DEFECTIVE COLLAPSIBLE STEERING SHAFT SYSTEM ON 1987-1995 VEHICLES MANUFACTURED BY THE DAIMLERCHRYSLER CORPORATION.IN PART BECAUSE OF 49 CFR ? 30120(G), NHTSA HAS DECIDED TO LIMIT THE SCOPE OF THE PETITION VEHICLES TO 1993-1995 MODELS, EXCLUDING THE 1993 JEEP GRAND CHEROKEE AND 1994-1995 DODGE RAM SERIES TRUCKS THAT WERE RECALLED (93V210 & 96V230) FOR STEERING COLUMN FAILURE.IF THE ANALYSIS OF THESE VEHICLES HAD IDENTIFIED A POTENTIAL PROBLEM, THE SCOPE COULD HAVE BEEN EXPANDED IN AN INVESTIGATION.A REVIEW OF ODI'S DATA BASE SHOWS NO RECENT COMPLAINTS AND A LACK OF A COMPLAINT TREND CONCERNING THE SUBJECT ISSUE ON THE SUBJECT VEHICLES AS A WHOLE OR BY INDIVIDUAL MODELS.THEREFORE, THE PETITION IS DENIED.FOR DETAILS, SEE FEDERAL REGISTER NOTICE VOLUME 68, NO. 130, JULY 8, 2003.
PE02082 · Safety Belt Cinching Latch Plate
Opened Nov 6, 2002 · Closed Apr 23, 2003
Status: closed (inferred from source dates) · Seat Belts
THERE ARE NO INJURIES OR FATALITIES ASSOCIATED WITH THIS ALLEGED DEFECT.WHILE CONDUCTING THIS INVESTIGATION, ODI FOUND THAT THE SUBJECT CINCHES MEET THE LOAD BEARING REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD 208, AND THAT MANY OF THE REPORTED FAILURES WERE DUE TO INCORRECT CHILD SAFETY SEAT INSTALLATIONS. ADDITIONALLY, THE REPORT RATE IS LOW (1.60/100K).THE INFORMATION AVAILABLE FAILS TO ESTABLISH THE EXISTENCE OF A DEFECT TREND AT THIS TIME.FURTHER ALLOCATION OF AGENCY RESOURCES TO THIS ISSUE IS UNWARRANTED AND THE PRELIMINARY EVALUATION IS BEING CLOSED.
EA97016 · Lower Control Arm Ball Joint Failure
Opened Sep 29, 1997 · Closed Nov 20, 1997
Status: closed (inferred from source dates) · Suspension
BY LETTER DATED NOVEMBER 6, 1997, THE MANUFACTURER ADVISED THIS AGENCY OF ITS DECISION TO INITIATE A SAFETY RECALL CAMPAIGN OF THE SUBJECT VEHICLES TO CORRECT THE DEFECT IDENTIFIED IN THIS EA.THE RECALL WILL ALSO COVER 1996 AND 1997 CHRYSLER CIRRUS/DODGE STRATUS VEHICLES, AS WELL AS 1995 THROUGH 1997 CHRYSLER SEBRING CONVERTIBLE AND PLYMOUTH BREEZE VEHICLES EQUIPPED WITH IDENTICAL LOWER CONTROL ARM BALL JOINTS.AN ESTIMATED TOTAL OF 599,00VEHICLES ARE AFFECTED BY THIS RECALL.THE MANUFACTURER'S INVESTIGATION DISCLOSED THAT PROCESS VARIABILITY, TOGETHER WITH THE BALL JOINT HOUSING COVER CRIMPING OPERATION, CAN RESULT IN AN INEFFECTIVE SEAL THAT PERMITS A LOSS OF LUBRICATION AND ACCELERTED WEAR OF THE BALL JOINT ASSEMBLY.THIS CONDITION CAN LEAD TO FAILURE AND SEPARTION OF THE LOWER CONTROL ARM BALL JOINT.THE RECALL IS IDENTIFIED AS NHTSA 97V-201 AND A COPY OF CHRYSLER'S LETTER TO NHTSA IS ATTACHED HERETO.
PE97009 · Lower Control Arm Ball Joint Failure
Opened Mar 13, 1997 · Closed Sep 29, 1997
Status: closed (inferred from source dates) · Suspension
THE MANUFACTURER IDENTIFED VEHICLE OWNER COMPLAINTS OF THE SUBJECT BALL JOINT FAILURES AS TABULATED ABOVE.IN ADDITION, A TOTAL OF 72 WARRANTY REPORTS WERE IDENTIFIED FOR REPLACEMENT OF BROKEN OR CRACKED BALL JOINT ASSEMBLIES IN THE SUBJECT VEHICLES.CHRYSLER ALSO REPORTED THAT 1996 AND 1997 MODELS ARE EQUIPPED WITH IDENTICAL BALL JOINT ASSEMBLIES AS THE SUBJECT 1995 MODEL YEAR VEHICLES.A PARTIAL RESPONSE TO NHTSA'S INFORMATION REQUEST INDICATED THAT THE MANUFACTURER'S ANALYSES AND EVALUATIONS OF THE CONDITION WERE CONTINUING.IN ORDER TO CONTINUE NHTSA'S COMPLETE ASSESSMENT OF THE NATURE AND SCOPE OF THIS MATTER, THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS.