Steering. Review the 222 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Electrical System. Review the 45 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Suspension. Review the 36 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

4 crash reports8 fire reports2 injury reports

Wheels complaints

15 reports

Clear category filter

Mileage unknown · Sep 17, 2025

Wheels

Drivers side rear wheel broke loose from hub and bounced into the opposing lane of traffic.

NHTSA ODI #11687970

307,000 miles · Aug 4, 2023

Wheels

Read full complaint

The contact owns a 2012 Ram 3500. The contact stated that after driving at an undisclosed speed, he stopped at the gas station and went inside to pay for fuel; however, when the contact returned to the vehicle, he became aware that the rear passenger’s side wheel was missing five studs. The contact stated that he was able to safely drive the vehicle to the dealer, where the wheel was inspected and the dealer was able to diagnose the failure; however, the vehicle was not repaired. The contact stated that there was a previous safety recall for the vehicle, but when the vehicle was taken for the recall repair, the recall repair was not completed; the wheels were only inspected. The manufacturer was made aware of the failure; however, the contact stated that the manufacturer originally approved completing the repair as a recall repair and then declined the approval. The failure mileage was approximately 307,000.

NHTSA ODI #11536453

247,000 miles · Jul 26, 2022

Wheels

Read full complaint

The contact owns a 2012 Ram 3500. The contact stated while driving 60 MPH, there was an abnormally roaring sound coming from the vehicle. The contact stated that while slowing down, the rear wheels detached from the wheel studs with the lug nuts. The vehicle was towed to the dealer and the contact was informed that the lug nuts were torqued too tight on the studs. The contact referenced NHTSA Campaign Number: 21V398000 (Wheels). The vehicle was repaired. The contact stated that he also noticed that the lug nuts on the front wheels were missing. The dealer and the manufacturer were notified of the failure. The contact was informed that the repair would be an out-of-pocket expense. The failure mileage was 247,000.

NHTSA ODI #11475949

Mileage unknown · Aug 6, 2021

Wheels

Read full complaint

The contact owns a 2012 Ram 3500. The contact received notification for NHTSA Campaign Number: 21V398000 (Wheels) however, the part to do the recall repair was unavailable. The dealer was made aware of the issue and it was confirmed that the part was not available. The contact stated that the manufacturer had exceeded a reasonable amount of time for the recall repair. The manufacturer was made aware of the issue. The contact had not experienced a failure. VIN tool confirms parts not available.

NHTSA ODI #11428084

Mileage unknown · Jun 8, 2021

Wheels

Read full complaint

While driving down the highway, 7 of 8 lug studs of the right front wheel spontaneously broke off. Vehicle became difficult to control and steer. The one remaining lug stud kept the wheel on long enough to pull onto the shoulder of the road. This was a heavily travelled interstate highway. My safety and the safety of other motorists was at high risk. Broken lug studs are available for inspection. All of them broke at the location where the threads end at the shoulder of the bolt. I had recently performed brake service and the wheels were mounted and properly torqued to manufacturer specifications. No police report or dealer inspection. I made the repairs. No prior warning of the problem. This is identical to the problem a friend had with his Ram dually, that is now in a recall. Part number is 6509866AA. I have owned this vehicle since it was new.

NHTSA ODI #11420179

142,000 miles · Sep 19, 2017

Wheels

ALCOA 17" RIMS CRACKED IN 4 PLACES ON DRIVER SIDE STEER. OTHER RIMS BEGINNING TO CRACK. HAD TO REPLACE ALL 4 ALCOA RIMS.

NHTSA ODI #11024269

127,900 miles · Sep 13, 2017

Fuel/propulsion SystemPower TrainWheels

Read full complaint

TL* THE CONTACT OWNS A 2012 RAM 3500. WHILE DRIVING APPROXIMATELY 70 MPH AND TOWING A 2017 WOOD DECK TRAILER FMCW-11000-20S, THE CONTACT HEARD A BANGING NOISE UNDERNEATH THE FLOORBOARD. SUDDENLY, THE FRONT DRIVE SHAFT AND TRANSFER CASE SEPARATED AND BLEW UP. THERE WERE NO WARNING INDICATORS ILLUMINATED. THE CONTACT PULLED OVER TO INSPECT THE VEHICLE AND WAS INFORMED THAT HIS HUBCAP FELL OFF. WHILE ATTEMPTING TO SHIFT THE GEAR INTO DRIVE, THE GEAR SHIFTER FAILED. UPON FURTHER INSPECTION OF THE VEHICLE, THE CONTACT NOTICED THAT FLUID LEAKED ONTO THE GROUND FROM UNDERNEATH THE VEHICLE AND THAT THE TRANSFER CASE AND DRIVE SHAFT WERE GONE. THE VEHICLE WAS TOWED TO KING CITY CHRYSLER CENTER (1603 BROADWAY ST, MT VERNON, IL 62864 (618) 242-6600) WHERE IT WAS DIAGNOSED THAT THE TRANSMISSION WAS CRACKED, THE AXLE WAS COMPROMISED, AND THE TRANSMISSION, FRONT DRIVE SHAFT, TRANSFER CASE, ENTIRE FRONT AXLE, FUEL LINES, TRANSMISSION WIRING HARNESS, SHIFT CABLE, AND TRANSMISSION COOLER LINES ALL NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 127,900.

NHTSA ODI #11023296

45,000 miles · Nov 17, 2016

Wheels

ALUMIMUM WHEEL CRACKING CRACKED IN MAY OR JUNE 2016 AND IN NOV. 2016

NHTSA ODI #10926675

74,820 miles · Mar 2, 2016

Wheels

Read full complaint

THE WHEEL STUDS BREAK WHENEVER I'M CHANGING TIRES, I'VE REPLACED 7 TOTAL. I HAVE TO PUT THEM ON VERY GENTLY THEN I TORQUE DOWN BY HAND. I RUN A FLEET OF TRUCKS AND DO MECHANIC WORK. THIS IS THE FIRST VEHICLE I'VE HAD TO DO THIS ON. RIGHT NOW I'M SITTIN ON THE SIDE OF THE ROAD BECAUSE MY RIGHT/REAR TIRE FELL OFF DUE TO ALL MY STUDS BREAKING. I HAVE HEARD OF OTHER RAM OWNERS HAVING ISSUES, THE DEALER SAID THAT THEY AND I'M OVER TIGHTENING BUT I'VE NEVER HAD THIS BEFORE. THESE ARE LUG NUTS... COME ON RAM, GET IT TOGETHER AND DO A RECALL. THIS IS A SAFETY CONCERN. IF I WERE ON THE HIGHWAY WITH A MOTORCYCLIST NEXT TO ME HE/SHE COULD HAVE DIED. I WAS MOVING 57MPH WHEN IT FELT LIKE I WAS GOING INTO A DIP AND THEN I SAW SPARKS FROM MY ROTOR, AND SAW MY TIRE/RIM GO FLYING OUT OF THE DITCH. IT PASSED ME AND NOW IS SITTING IN THE FIELD. IF I WERE HAULING A TRAILER IT WOULD HAVE BEEN TERRIBLE ALSO.

NHTSA ODI #10839346

95,000 miles · Oct 6, 2015

Air BagsSteeringWheels

HIGHWAY DRIVING MOSTLY. GOING THROUGH TIRES. TIRES KEEP GETTING CHOPPED. WE HAUL HEAVY LOADS AND WORRY THE VEHICLE IS NOT SAFE FOR THE TYPE OF BUSINESS WE DO. BUT WE CAN'T GET RID OF IT BECAUSE OF ALL THIS RECALL. THE PREVIOUS OWNER HAD PART OF THE RECALL ADDRESSED BUT WE STILL FEEL THE VEHICLE IS NOT SAFE. WE SEE SIGNS OF WEAR …

Read full complaint

NHTSA ODI #10780060

Official recalls

21V398000 · Wheels:lugs/nuts/bolts/studs

May 27, 2021

Chrysler (FCA US, LLC) is recalling certain 2012-2021 RAM 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles. Incorrect information in the Service and Owner's Manuals may cause the flanged lug nuts to be over-tightened, which could result in a broken wheel stud and possible wheel separation.

Consequence & remedy

Consequence: Wheel separation can cause a vehicle crash.

Remedy: Dealers will update the torque specification in the owner's manual and other published service documents. Dealers will also inspect the vehicle's wheel studs, replacing them if necessary, free of charge. Owner notification letters were mailed on November 30, 2021. Campaign Y36 owner notification letters were mailed on November 30, 2021. Campaign Y26 owner notification letters were mailed on December 1, 2021. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's numbers for this recall are Y26 and Y36.

17V824000 · Equipment

Dec 21, 2017

Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf

Consequence & remedy

Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.

Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.

17V821000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Dec 20, 2017

Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.

Consequence & remedy

Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.

Remedy: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.

16V739000 · Electrical System:alternator/generator/regulator

Oct 13, 2016

Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger Police vehicles, 2007-2013 RAM 3500 Cab Chassis, 2008-2013 RAM 4500 and 5500 Cab Chassis, and 2013 RAM 2500 and 3500 vehicles. The affected vehicles have a 220 amp alternator that may suddenly fail.

Consequence & remedy

Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will replace the alternator with a revised alternator, free of charge. The recall began on December 23, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S68.

15V459000 · Air Bags:frontal

Jul 22, 2015

Chrysler (FCA US LLC) is recalling certain model year 2012-2014 Ram 1500, 2500, 3500, 4500, and 5500 trucks manufactured January 18, 2011, to October 7, 2014, and equipped with the Electronic Vehicle Information Center option. The affected vehicles have a steering wheel wiring harness that may rub against the driver air bag module retainer spring.

Consequence & remedy

Consequence: This abrasion may result in an electrical short that could cause driver's frontal air bag to unexpectedly deploy. Inadvertent deployment of the air bag may increase the risk of injury and the possibility of a vehicle crash.

Remedy: Chrysler will notify owners, and dealers will inspect, repair as necessary, and secure the steering wheel wiring harness. Additionally, protective caps will be added to the air bag retainer spring ends. These repairs will be done free of charge. The recall began on September 18, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R36.

14V635000 · Engine And Engine Cooling:engine:diesel; Fuel System, Diesel

Oct 8, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.

Consequence & remedy

Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.

Additional source detail variants (2)

Fuel System, Diesel

Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.

Engine And Engine Cooling:engine:diesel

Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.

13V529000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.

13V344000 · Power Train:automatic Transmission

Aug 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2012 RAM 3500 trucks manufactured May 4, 2012, through August 7, 2012; and model year 2012 RAM 4500 and 5500 trucks manufactured May 3, 2012, through August 7, 2012. Due to a loose snap ring inside the transmission, there may be a loss of power transfer through the transmission to the wheels.

Consequence & remedy

Consequence: An unexpected loss of power transfer may increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the transmission assembly free of charge. The recall began on October 17, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N50.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

EA19001 · Electrical Overstress

Opened Apr 19, 2019 · Closed Sep 19, 2024

Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module

The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.