Steering. Review the 109 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Electrical System. Review the 51 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Engine. Review the 44 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

8 crash reports12 fire reports4 injury reports

What owners actually said

283 reports

Mileage unknown · Jan 13, 2023

Steering

Tie rod end sheared/broke causing the vehicle to be un-stearable. Fortunately, it happened as I was backing out of my driveway.

NHTSA ODI #11501693

Mileage unknown · Dec 20, 2022

Engine

Exhaust Manifold on passenger side is leaking. It has a broken bolt due to manifold warping. This is causing exhaust to leak into the cab.

NHTSA ODI #11498190

151,000 miles · Oct 25, 2022

Tires

Read full complaint

The contact owns a 2012 RAM 2500 equipped with Kenda Tires, Tire Line: Klever, Tire Size: LT275/70/R18, DOT Number: 02T6NAANL12228260. The contact stated while driving 60 MPH, the vehicle started bouncing. The contact stated no warning light was illuminated. The contact continued to drive back to the tire shop and was informed that the front passenger’s side tire was showing tread separation. The tire shop replaced the front passenger’s side tire. The contact stated that approximately two weeks later, he experienced the same failure with the front driver’s side tire. The contact took the vehicle back to the tire shop and had the front driver’s side tire replaced with the spear tire. The vehicle was not diagnosed or repaired. A dealer was not contacted. The contact stated that he had left a voicemail with the manufacturer but had not yet received a callback. The failure mileage was approximately 151,000.

NHTSA ODI #11490842

Mileage unknown · Oct 7, 2022

Suspension

Read full complaint

When driving at highway speed, if I hit the seam between the road and a bridge and it is not smooth my truck goes into a, "Death wobble." The steering wheel and the whole truck shakes uncontrollably. I can barely keep it in the road. It will only stop when the vehicle slows below 30mph. This problem started about 48,000 miles, I only have a little over 56,000 now. I have changed the stabilizer, got new tires and an alignment. I will be taking it to a mechanic on the 17th but I really believe the manufacture should have a recall on this vehicle. It is very dangerous. I am not the only person to own one of these trucks and this happens to.

NHTSA ODI #11488389

Mileage unknown · May 24, 2022

Engine

Read full complaint

The exhaust manifold bolts on both sides of the engine warp due to two different metals being put together under heat. Steel and aluminum expand at different temperatures. This causes the bolts to break off of the exhaust manifold creating an exhaust leak into the engine bay. Yes, this can be inspected upon request. The safety of myself and the general public is at risk due to the exhaust leak into the engine bay being pulled into the cab via the heating or airconditioning system. The exhaust fumes are pulled into the cab of the truck via the heating and airconditioning system. When running, the truck has a very noticeable smell inside the cab. It has caused me headaches as well. This poses a risk to the public if the driver were to pass out from said fumes. The problem can be reproduced and is a known issue with Dodge. It is very well documented online that this problem happens to nearly all Dodge Ram trucks. It has never been recalled because Dodge says its not a "safety" concern. This is very much so a safety issue. The components have been inspected by others, and verified as broken. I will not take it to a dealership to have it inspected as they want to charge 150$/hr to diagnose something that even they recognize as a known issue. There were no warning lamps, messages or any visible indication of this problem. A loud ticking noise and a strong smell of exhaust fumes are what brought the issues to attention.

NHTSA ODI #11465983

Mileage unknown · Feb 27, 2022

Engine

Read full complaint

My Dodge Ram 2500, 2012 Hemi engine started making a ticking sound so got a tune up. The machinic changed the spark plugs and distributors around after I complained. Nothing he was able to do enable the truck to function properly. I spoke with the Dodge dealership, the spoken informed me that when Dodge merged with MERCEDE the problem persisted and to this date a fix was not provided. I spoke with other Dodge owner who experience the same problem. The engine was not functioning properly because of internal damage. The cost of repair would cost between $8K and $10K to replace or repair the engine. The dealership stated that NHTSA nor Dodge have provided a fix and that the problem still persist to this day.

NHTSA ODI #11454342

Mileage unknown · Feb 12, 2022

Engine

Engine has been making a ticking noise on the passenger side for the past few months. The passenger side exhaust manifold warped and broke two bolts in the engine block. This caused an exhaust leak and made the truck run rich due to the leak before oxygen sensor. Fuel efficiency declined. Replaced the exhaust manifold, gaske…

Read full complaint

NHTSA ODI #11451688

Mileage unknown · Jan 22, 2022

Engine

Read full complaint

The bolts holding the exhaust manifold to the engine cylinder head, are breaking off. This has occurred in the past, on the drivers and passengers side. I had the problem repaired, by a dealer, which required the replacement of the passenger side cylinder head as well. This issue has re-occurred on the drivers side, which has been confirmed by a Ram dealer, as shown in the attached documentation. In every instance, the issue starts with a tapping noise, as the exhaust manifold pulls away from the head. Passengers in my truck have complained about the smell of exhaust fumes, which is a safety and health issue. This truck only has 85,000 miles, yet this is the 3rd incident of this issue occurring.

NHTSA ODI #11448459

216,000 miles · Jun 8, 2021

Electrical System

Read full complaint

The contact owns a 2012 Ram 2500. The contact stated while driving approximately 40-60 mph, on several occasions after driving over a bump in the roadway, the vehicle loss steering and braking functionality before the vehicle loss motive power. The vehicle was taken to an independent mechanic who diagnosed that the wireless ignition node module was faulty. The mechanic retrieved a fault code. The vehicle was not repaired. The dealer and the manufacturer were made aware of the failure however, no assistance was offered. The contact was relating the failure to NHTSA Campaign Number: 10V200000 (Electrical System). The failure mileage was 216,000.

NHTSA ODI #11420109

170,000 miles · May 21, 2021

Steering

The contact owns a 2012 Ram 2500. The contact stated that after making the third right turn while driving approximately 3 -5 MPH, the steering linkage fractured and the vehicle loss steering functionality. The vehicle was towed to the dealer to be diagnosed. The contact was informed that the drag link and the steering system nee…

Read full complaint

NHTSA ODI #11418041

Official recalls

17V821000 · Power Train:automatic Transmission:lever And Linkage:column Shift

Dec 20, 2017

Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.

Consequence & remedy

Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.

Remedy: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.

15V459000 · Air Bags:frontal

Jul 22, 2015

Chrysler (FCA US LLC) is recalling certain model year 2012-2014 Ram 1500, 2500, 3500, 4500, and 5500 trucks manufactured January 18, 2011, to October 7, 2014, and equipped with the Electronic Vehicle Information Center option. The affected vehicles have a steering wheel wiring harness that may rub against the driver air bag module retainer spring.

Consequence & remedy

Consequence: This abrasion may result in an electrical short that could cause driver's frontal air bag to unexpectedly deploy. Inadvertent deployment of the air bag may increase the risk of injury and the possibility of a vehicle crash.

Remedy: Chrysler will notify owners, and dealers will inspect, repair as necessary, and secure the steering wheel wiring harness. Additionally, protective caps will be added to the air bag retainer spring ends. These repairs will be done free of charge. The recall began on September 18, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R36.

14V635000 · Engine And Engine Cooling:engine:diesel; Fuel System, Diesel

Oct 8, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.

Consequence & remedy

Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.

Additional source detail variants (2)

Fuel System, Diesel

Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.

Engine And Engine Cooling:engine:diesel

Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.

13V529000 · Steering:linkages:tie Rod Assembly

Nov 6, 2013

Chrysler Group LLC (Chrysler) is recalling certain model year 2008-2012 RAM 2500 4X4 and 3500 4X4 trucks, 2008-2012 Dodge RAM 3500 4x2 Cab Chassis, and model year 2008 Dodge RAM 1500 Mega Cab 4x4. The left tie rod assembly may break.

Consequence & remedy

Consequence: A failure of the tie rod assembly may result in a loss of steering control, increasing the risk of a crash.

Remedy: Chrysler notified owners on January 16, 2014 that dealers would inspect vehicles and replace the steering linkage assembly, if necessary. On or about February 27, 2014, Chrysler ceased its recall remedy program due to parts quality concerns, and then re-initiated it on or about April 14, 2014. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N49.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

EA19001 · Electrical Overstress

Opened Apr 19, 2019 · Closed Sep 19, 2024

Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module

The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.