NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
688 reports57,768 miles · Mar 30, 2018
Structure
DURING A PA STATE INSPECTION THEY FOUND ONE OF THE FUEL TANK SUPPORT STRAPS HAD PULLED OUT OF THE FRAME. THE FRAME HAD RUSTED IN THE AREA WHERE THE STRAP USE TO BE ATTACHED TO THE FRAME. THIS LEFT THE TANK WITH 150LBS OF GASOLINE IN IT HANGING BY ONE STRAP, THIS COULD HAVE BEEN CATASTROPHIC IF THE TANK FELL OUT AND BECAME WED…
Read full complaint
DURING A PA STATE INSPECTION THEY FOUND ONE OF THE FUEL TANK SUPPORT STRAPS HAD PULLED OUT OF THE FRAME. THE FRAME HAD RUSTED IN THE AREA WHERE THE STRAP USE TO BE ATTACHED TO THE FRAME. THIS LEFT THE TANK WITH 150LBS OF GASOLINE IN IT HANGING BY ONE STRAP, THIS COULD HAVE BEEN CATASTROPHIC IF THE TANK FELL OUT AND BECAME WEDGED UNDER THE AXLE. IT IS GOING TO COST OVER $650 TO HAVE THE FRAME WELDED. VEHICLE IS A 2011 WITH 57K MILES.
NHTSA ODI #11082133
112,000 miles · Mar 27, 2018
Unknown Or Other
KEY FOB EJECTS FROM WIRELESS IGNITION NODE CAUSING LOSE OF POWER STEERING AND BRAKES ON THE INTERSTATE AND IN THE CITY WHILE IN MOTION.
NHTSA ODI #11081472
51,200 miles · Mar 17, 2018
Fuel/propulsion System
CHECK ENGINE LIGHT CAME ON,FOLLOWED BY " THROTTLE CONTROL SENSOR " TRUCK ALMOST STALLED , THEN SEEMED SLUGGISH . DEALERSHIP REPLACED ACCELERATOR RELATED SENSOR. 2 WEEKS LATER, SAME THING HAPPENED, SAME LOCATION, ONLY THIS TIME, AFTER ALMOST STALLING, TRUCK HAD LITTLE POWER. TAKING A RIGHT TURN AT THE NEXT STREET I HAD MY FOOT ON…
Read full complaint
CHECK ENGINE LIGHT CAME ON,FOLLOWED BY " THROTTLE CONTROL SENSOR " TRUCK ALMOST STALLED , THEN SEEMED SLUGGISH . DEALERSHIP REPLACED ACCELERATOR RELATED SENSOR. 2 WEEKS LATER, SAME THING HAPPENED, SAME LOCATION, ONLY THIS TIME, AFTER ALMOST STALLING, TRUCK HAD LITTLE POWER. TAKING A RIGHT TURN AT THE NEXT STREET I HAD MY FOOT ON THE BRAKE, WHEN L TOOK MY FOOT OFF THE BRAKE, THE TRUCK ACCELERATED ON ITS OWN, WITHOUT MY FOOT ON THE PEDAL, CREATING A DANGEROUS SITUATION. TRUCK WAS TOWED TO DEALERSHIP, WHERE THEY ARE EXAMINING THE WIRE HARNESS FOR A SHORT. I DON'T KNOW IF I WILL FEEL SAFE OPERATING THIS VEHICLE AGAIN.
NHTSA ODI #11079979
Mileage unknown · Mar 16, 2018
Electrical SystemEngineFuel/propulsion System
MY TRUCK FAILS TO START RANDOMLY, IT JUST CRANKS. THE HORN WILL RANDOMLY GO OFF BY ITSELF, AND IT HAS STALLED ON ME TWICE WHILE DRIVING. AFTER MUCH RESEARCH, IT APPEARS THE TIPM IS BAD. OTHER 2011 CHRYSLER VEHICLES HAVE THE SAME ISSUES, AND HAVE HAD A RECALL.
NHTSA ODI #11079730
Mileage unknown · Mar 5, 2018
Power Train
MY 2005 DODGE RAM HAD A RECALL FOR REAR PINION ISSUE. NOW I HAVE A 2011 DODGE RAM THAT IS HAVING THE SAME NOISE FROM THE REAR END. HA E HAD IT LOOKED AT BY MULTIPLE MECHANICS AND HAVE BEEN TOLD IT'S THE REAR PINION BEARINGS IN THIS TRUCK AD WELL.
NHTSA ODI #11076259
57,000 miles · Feb 27, 2018
Service Brakes
TL* THE CONTACT OWNS A 2011 RAM 1500. THE CONTACT STATED THAT BOTH BRAKE CALIPERS FAILED AND CAUSED THE ROTORS TO FAIL. THERE WERE NO WARNING INDICATORS ILLUMINATED BEFORE OR AFTER THE FAILURE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THE VEHICLE WAS REPAIRED, BUT THE FAILURE RECURRED. THE DEALER WAS NOT NOTIFIED O…
Read full complaint
TL* THE CONTACT OWNS A 2011 RAM 1500. THE CONTACT STATED THAT BOTH BRAKE CALIPERS FAILED AND CAUSED THE ROTORS TO FAIL. THERE WERE NO WARNING INDICATORS ILLUMINATED BEFORE OR AFTER THE FAILURE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THE VEHICLE WAS REPAIRED, BUT THE FAILURE RECURRED. THE DEALER WAS NOT NOTIFIED OF THE FAILURE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 57,000.
NHTSA ODI #11075209
Mileage unknown · Feb 27, 2018
Electrical SystemEngineUnknown Or Other
2 YEARS AGO HAD TO REPLACE THE TIPM ON MY TRUCK AND NOE ITS STARTING TO MESS UP AGAIN. TRUCKS JUST DIES WHILE DRIVING NO WARNING. IT JUST A MATTER OF TIME BEFORE I HAVE TO REPLACE IT AGAIN. IT SHOULD BE A RECALL. IT COST ME 1500.00 TO REPAIR
NHTSA ODI #11075181
95,000 miles · Feb 18, 2018
Engine
L BACKED OUT OF MY DRIVEWAY AND SHIFTED TO DRIVE THE TRUCK SHUT DOWN. THIS HAPPENED A COUPLE OF TIMES AND NOW IT SHUTS DOWN WHILE DRIVING AT 35 - 40 MPH.
NHTSA ODI #11073456
140,000 miles · Feb 17, 2018
Engine
ENGINE LIFTERS. I HAVE A 2011 DODGE RAM 1500 I NOTICED A TICKING NOISE COMING FROM THE TOP OF THE ENGINE. UPON A FREE DIAGNOSTICS TEST I WAS TOLD MY TRUCK HAS LIFTER FAILURE. THE ENGINE STALLS IN TRAFFIC HARD TO START QUOTE TO FIX $3500 TO FIX. IF I LIVED IN A BIGGER CITY I WOULD HAVE BEEN IN A WRECK BY NOW BECAUSE IT ISN'T DR…
Read full complaint
ENGINE LIFTERS. I HAVE A 2011 DODGE RAM 1500 I NOTICED A TICKING NOISE COMING FROM THE TOP OF THE ENGINE. UPON A FREE DIAGNOSTICS TEST I WAS TOLD MY TRUCK HAS LIFTER FAILURE. THE ENGINE STALLS IN TRAFFIC HARD TO START QUOTE TO FIX $3500 TO FIX. IF I LIVED IN A BIGGER CITY I WOULD HAVE BEEN IN A WRECK BY NOW BECAUSE IT ISN'T DRIVABLE IT STALLS OUT NO POWER STEERING HARD TO TURN BRAKES ARE HARD TO PUSH SOMETIMES IT TAKES A WHILE TO START BACK UP I WOULDN'T WANT TO BE ON A BUSY HIGH WAY. THIS ISN'T JUST A MANUFACTURING PROBLEM IT IS A SAFETY ISSUE AND NEEDS ACTION.
NHTSA ODI #11073380
1,000,000 miles · Feb 16, 2018
Unknown Or Other
MY TRUCK WOULD NOT START HAD IT DIAGNOSED. FOUND IT WAS ACOMMON PROBLEM. THE TIPM PART# RL692319AJ FOUND TO COST 900.00 CRAZY. IT WAS FOUND TO BE TO COMMON OF PROBLEM NOT TO BE ON A RECALL .......................I WOULD LIKE SOMEONE TO TAKE RESPONSIBILITY FOR SUCH AN EXPENSIVE REPAIR.
NHTSA ODI #11073268
Official recalls
4Mar 8, 2018
Chrysler (FCA US LLC) is recalling certain 2009-2012 Dodge Ram 1500 trucks currently, or ever registered, in Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia. Exposure to environmental conditions such as water mixed with road salt may cause the front fuel tank strap frame "T-Slot" bracket to corrode, possibly causing the fuel tank to drop and make contact with the ground.
Consequence & remedy
Consequence: If the fuel tank were to drop and contact the ground, a fuel leak may result. Additionally, in the event of a crash, the fuel tank may not remain secured to the vehicle, possibly causing a fuel leak. A fuel leak in the presence in an ignition source, can increase the risk of a fire.
Remedy: Chrysler will notify owners and dealers will bolt a bracket reinforcement to the frame, free of charge. The recall began May 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U04.
Dec 20, 2017
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
Consequence & remedy
Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
Feb 6, 2013
Chrysler is recalling certain model year 2009-2012 Ram 1500 trucks manufactured from February 27, 2008, through June 30, 2009, and from December 1, 2009, through October 20, 2011; model year 2009-2011 Dodge Dakota trucks manufactured from February 27, 2007, through June 30, 2009, and from December 1, 2009, through September 30, 2011; model year 2009 Chrysler Aspen trucks manufactured from January 3, 2008, through December 18, 2008; and model year 2009 Dodge Durango trucks manufactured from January 3, 2008, through December 18, 2008. The rear axle pinion nut may loosen due to an undersized pinion spline that can allow relative motion between the nut and companion flange.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: On November 7, 2013 Chrysler notified owners that dealers would install a pinion nut retainer, free of charge. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N08.
Dec 24, 2010
CHRYSLER IS RECALLING CERTAIN MODEL YEAR 2011 RAM 1500 TRUCKS MANUFACTURED FROM SEPTEMBER 2009 THROUGH DECEMBER 2010. SOME VEHICLES MAY HAVE EXPERIENCE A NOISE (GROWL, GRIND) COMING FROM THE REAR AXLE BEARING WHICH COULD EVENTUALLY SEIZE.
Consequence & remedy
Consequence: A FAILURE OF THE BEARING COULD CAUSE THE VEHICLE TO STALL INCREASING THE RISK OF A CRASH.
Remedy: CHRYSLER WILL NOTIFY OWNERS AND WILL INSTALL AN OIL PORT INSERT INTO THE REAR AXLE FREE OF CHARGE. THE SAFETY RECALL BEGAN ON APRIL 4, 2011. OWNERS MAY CONTACT CHRYSLER AT 1-800-853-1403.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA19001 · Electrical Overstress
Opened Apr 19, 2019 · Closed Sep 19, 2024
Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
Illustration