IllustrationInvolved in an accident 2/09/26. Air bag did not deploy. Fractured sternum as a result.
2009 Dodge RAM 1500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Dodge RAM 1500 do not stand out strongly from the model-year median of 520.
About this comparison →How this year compares
Owner complaints by model year
Compare all RAM 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
740–25K
10725–50K
13150–75K
10475–100K
94100–150K
32150K+
542 reports with mileage · 128 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 231 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 97 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 50 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports2 fire reports18 injury reports
What owners actually said
670 reports- Week of October 6th 2025 I experienced 4-wheel drive issues and lights. - October 13th 2025 dropped off to dealer for review - October 14th 2025 dealer deemed not safe to drive and ordered parts under warranty repair. - following weeks went on with parts being backordered. - after having to push the dealer for updates for week…
Read full complaint
- Week of October 6th 2025 I experienced 4-wheel drive issues and lights. - October 13th 2025 dropped off to dealer for review - October 14th 2025 dealer deemed not safe to drive and ordered parts under warranty repair. - following weeks went on with parts being backordered. - after having to push the dealer for updates for weeks on December 22nd 2025 I informed Stellantis Customer Service US. - Customer service looked into and gave me the same delayed responses for weeks now "I hope you're doing well. I'm following up regarding your case. There is no definite ETA for the part. Our parts team is working to get it expedited. I will receive another update in 5-6 business days and will follow up with you then. If you have any questions please don't hesitate to contact me." - Still today Stellantis cannot give me a date when my truck will be repaired. Near 4months later...
The contact owns a 2009 Dodge Ram 1500. The contact stated that while driving at an undisclosed speed, the MTC unit failed to function as intended. The contact stated that while the system was enabled, the system independently switched between the heating and cooling systems. In addition, the defrost system was deactivated. The …
Read full complaint
The contact owns a 2009 Dodge Ram 1500. The contact stated that while driving at an undisclosed speed, the MTC unit failed to function as intended. The contact stated that while the system was enabled, the system independently switched between the heating and cooling systems. In addition, the defrost system was deactivated. The vehicle was not diagnosed or repaired by an independent mechanic or dealer. The contact referenced an unknown recall; however, the VIN was not under recall. The manufacturer was not made aware of the failure. The failure mileage was approximately 158,000.
The left turn signal not working properly. When I put my left turn signal the amber light front of the truck not working instead the high bean works as turn signal also amber running light not working. Is so frustrating getting pulled over by a cop for that reason!!!
Odometer Fraud. The contact purchased a 2009 Dodge Ram 1500. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 131,000 and at the time of registration, it was discovered on the …
Read full complaint
Odometer Fraud. The contact purchased a 2009 Dodge Ram 1500. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a private sale. At the time of purchase, the vehicle mileage was 131,000 and at the time of registration, it was discovered on the title that the mileage was 211,492.
CARFAX GOT THE WRONG MILEAGE 1 HAVE 185292 AND I CAN SEND PICTURES
Heating & ventilation, I have lost heat in my truck, issues with fuel pump/filte where truck won’t start, and had the water pump had to be replace. I believe the majority of the things listed had recalls. What is included in the recalls and can a recall be replaced more than 1x?
My trucks ignition switch just stops turing my truck on I've seen multiple complaints about the same issue leaves you stranded
The contact owns a 2009 Dodge Ram 1500. The contact stated that upon inspecting the vehicle, it was discovered that the fuel tank was not completely secured to the vehicle and was hanging down from the subframe. The failure was caused by a corroded subframe attaching the fuel tank straps to the vehicle. Both fuel tank straps had…
Read full complaint
The contact owns a 2009 Dodge Ram 1500. The contact stated that upon inspecting the vehicle, it was discovered that the fuel tank was not completely secured to the vehicle and was hanging down from the subframe. The failure was caused by a corroded subframe attaching the fuel tank straps to the vehicle. Both fuel tank straps had failed due to the subframe corrosion. The local dealer and manufacturer were notified of the failure, but no assistance was offered. The contact was informed that the VIN and vehicles from the state of Kansas were not included in NHTSA Campaign Number: 18V160000 (Fuel System, Gasoline). The contact stated that the vehicle had experienced the failure listed in the recall. The failure mileage was 149,000.
the shifter began changing gears on its own. Before the recall came out my mechanic checked and there was no recall for this until 2018. I was never notified of the recall. Then on rear axle pinion nut. The nuts were installed without the proper amount of adhesive. Consequently, the nuts can loosen, and cause the rear axle to …
Read full complaint
the shifter began changing gears on its own. Before the recall came out my mechanic checked and there was no recall for this until 2018. I was never notified of the recall. Then on rear axle pinion nut. The nuts were installed without the proper amount of adhesive. Consequently, the nuts can loosen, and cause the rear axle to lock up, causing a loss of vehicle control. I was never notified of and the rear end came down while on the freeway. The fuel tank began leaking I repaired this before the recall came out. I submitted a reimbursement request they denied me stating my car was over 7 years old.
Official recalls
213V038000 · Power Train:driveline:differential Unit
Feb 6, 2013
Chrysler is recalling certain model year 2009-2012 Ram 1500 trucks manufactured from February 27, 2008, through June 30, 2009, and from December 1, 2009, through October 20, 2011; model year 2009-2011 Dodge Dakota trucks manufactured from February 27, 2007, through June 30, 2009, and from December 1, 2009, through September 30, 2011; model year 2009 Chrysler Aspen trucks manufactured from January 3, 2008, through December 18, 2008; and model year 2009 Dodge Durango trucks manufactured from January 3, 2008, through December 18, 2008. The rear axle pinion nut may loosen due to an undersized pinion spline that can allow relative motion between the nut and companion flange.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: On November 7, 2013 Chrysler notified owners that dealers would install a pinion nut retainer, free of charge. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N08.
12V474000 · Power Train:driveline:differential Unit
Oct 2, 2012
Chrysler is recalling certain model year 2009-2010, Ram 1500 and Dodge Dakota trucks, manufactured from July 1, 2009, through November 30, 2009, because the rear axle pinion nut may loosen due to a lack of adhesive.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: Chrysler will notify owners, and dealers will install a pinion nut retainer, free of charge. The recall began on June 17, 2013. Owners may contact Chrysler at 1-800-247-9753.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2DP14004 · Totally Integrated Power Module Failure
Opened Sep 25, 2014 · Closed Jul 24, 2015
Status: closed (inferred from source dates) · Electrical System
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
PE12021 · Rear Differential Failure
Opened Jul 19, 2012 · Closed Mar 5, 2013
Status: closed (inferred from source dates) · Power Train; Power Train:automatic Transmission; Power Train:axle Assembly; Power Train:driveline; Power Train:driveline:differential Unit; Power Train:driveline:driveshaft; Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Additional source detail variants (14)
Power Train:automatic Transmission
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:automatic Transmission
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:axle Assembly
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:axle Assembly
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:differential Unit
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:differential Unit
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:driveshaft
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:driveshaft
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440