IllustrationIgnition,key fob will not correctly start engine. Engine dies going down the road , will not stay running after you start engine it just dies and kicks the key fob out to the floor. Trying to retrieve the fob and restarting the engine, and not crashing is a serious problem. Have nearly been in major crashes because of this .
2010 Dodge RAM 1500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2010 Dodge RAM 1500 do not stand out strongly from the model-year median of 520.
About this comparison →How this year compares
Owner complaints by model year
Compare all RAM 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
530–25K
7325–50K
7950–75K
5875–100K
59100–150K
32150K+
354 reports with mileage · 132 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 229 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 71 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 61 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
26 crash reports3 fire reports10 injury reports
What owners actually said
486 reportsWe have had our truck taken to Nyle Maxwell in Taylor Texas and they have were suppose to check the truck because two lights came up on the dash board which dash ESP ABS and traction control light.The shift stick was stuck in park. They towed it to there shop but the lights were off and the gear shift was working. I drove off th…
Read full complaint
We have had our truck taken to Nyle Maxwell in Taylor Texas and they have were suppose to check the truck because two lights came up on the dash board which dash ESP ABS and traction control light.The shift stick was stuck in park. They towed it to there shop but the lights were off and the gear shift was working. I drove off the lot had to stop at a light and my truck veered left sharply. They have looked at this problem twice. They are not finding anything but it is my truck I drive with my kids. We need so help. They also had to fix the ac and the serpentine belt because that broke while I was driving after they said it was good and safe to drive.
While driving my 2010 Dodge Ram 1500 Quad Cab, the key fob (FOBIK) has fallen out of the ignition while actively driving. The key can be removed from the ignition while actively driving with little to no effort. Upon this happening, the vehicle sometimes remains fully operable, at times it remains driving but looses speedometer,…
Read full complaint
While driving my 2010 Dodge Ram 1500 Quad Cab, the key fob (FOBIK) has fallen out of the ignition while actively driving. The key can be removed from the ignition while actively driving with little to no effort. Upon this happening, the vehicle sometimes remains fully operable, at times it remains driving but looses speedometer, wipers, heat/ac, running/brake lights and turn signals, or the vehicle will completely shut off, losing all function and drivability to include power steering. In one instance, the vehicle remained driving but lost wipers and lights during a night time storm. On another occasion, the vehicle lost all drivability traveling at a high rate of speed at night with traffic on a highway in a rural area with no streetlights. This defect has provided for a multitude of highly dangerous events while driving. There IS a recall (recall ref K08) describing this exact issue, however my VIN was not included in the recall and is not being recognized and or honored for recall repair by local Chrysler Dodge Dealerships or by Chrysler Headquarters. Chrysler Headquarters customer service communicated it is the responsibility of the NHTSB to add my VIN to the recall in order for the repair or replacement of the faulty WIN module along with replacement and programming of key fobs to be covered. This repair is estimated to cost $2500.
WIN module failure. When driving down the road/highway, the vehicle will turn off with no warning of any problems. The key can be removed while the vehicle is still running. The vehicle will start up with the key cranked diagonally but when released the vehicle dies making it more difficult to start the vehicle after it dies whi…
Read full complaint
WIN module failure. When driving down the road/highway, the vehicle will turn off with no warning of any problems. The key can be removed while the vehicle is still running. The vehicle will start up with the key cranked diagonally but when released the vehicle dies making it more difficult to start the vehicle after it dies while driving down the road/highway. When a bump is hit in the road the key moves and the vehicle dies. We have spoken to the local Dodge dealership who confirmed that it is a WIN module issue while servicing the vehicle due to other recalls as well as several locksmiths.
My husband was driving about 20mls per hrs when our truck cought fire the whole front of our truct cought fire. The front mirror and everything if distroit due to the fire .
Wireless ignition module fails and will stall out the engine. This can happen at speed or stopped. Wireless ignition module will intermittently fail and cause a loss of power at speed causing no power steering or power brakes
The frame has rusted thru, the fuel tank strap has failed and the fuel tank has dropped. If this had happened while driving, it could have killed him and many others. Upon researching for information, we found recall U04/nhsta 18v-160 which stated this document replaced service bulletin TSB# 1400218 - all for this exact pro…
Read full complaint
The frame has rusted thru, the fuel tank strap has failed and the fuel tank has dropped. If this had happened while driving, it could have killed him and many others. Upon researching for information, we found recall U04/nhsta 18v-160 which stated this document replaced service bulletin TSB# 1400218 - all for this exact problem. This was a regional recall/extended warranty and was not issued for vehicles in our region. But this document does state that should any vehicle meet the criteria described (make date range, model year, and problem) that that vehicle should be covered. My fathers truck meets all 3 criteria. Upon calling FCA (Fiat, Chrysler Automobiles), who issued the document, we were told that we aren't able to be included in this issue, since we don't have a recall listed and also because the recall turned from a recall to an extended warranty that expired in 2022. If this is a known issue why is there an expiration date on the repair of it? My father's truck only has about 67,000 miles on it, which is probably why the problem is only presenting now. And if we had known there was a possible chance that this could happen, why weren't we informed to check it? He is the original owner of the vehicle and we are appalled at the FCA repsonse. The document in reference is attached.
This incident has happened several times while driving on the road. When driving at slow speeds, approaching a red light, or slowing down to make a left or right turn, the vehicle shuts off without warning. The power steering and brakes stop working, making the car hard to handle. I have to put it in neutral, restart the vehicl…
Read full complaint
This incident has happened several times while driving on the road. When driving at slow speeds, approaching a red light, or slowing down to make a left or right turn, the vehicle shuts off without warning. The power steering and brakes stop working, making the car hard to handle. I have to put it in neutral, restart the vehicle, and start it back up without any problems. This is a very well-maintained vehicle and a daily driver. The car has 172000 miles on it. I have done internet research on this, and it seems to be a very common thing with Dodge Ram Trucks.
[XXX] My truck sway at 65mph, like a drunk person driving. Scary. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
The contact owns a 2010 Ram 1500. The contact stated while driving 40 MPH, there was an abnormal sound coming from the vehicle. The contact stated that the ESP, traction control, and ABS warning light illuminated. The vehicle was taken to the dealer and the tire pressure pump was replaced but the failure reoccurred. The vehicle …
Read full complaint
The contact owns a 2010 Ram 1500. The contact stated while driving 40 MPH, there was an abnormal sound coming from the vehicle. The contact stated that the ESP, traction control, and ABS warning light illuminated. The vehicle was taken to the dealer and the tire pressure pump was replaced but the failure reoccurred. The vehicle was taken to the dealer, and they stated that the ABS module needed to be replaced. The vehicle was not repaired. The manufacturer was contacted and stated that the part was no longer available. The failure mileage was 108,000.
Official recalls
418V160000 · Fuel System, Gasoline:storage:tank Assembly:mounting
Mar 8, 2018
Chrysler (FCA US LLC) is recalling certain 2009-2012 Dodge Ram 1500 trucks currently, or ever registered, in Connecticut, Delaware, Illinois, Indiana, Iowa, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, West Virginia, Wisconsin and the District of Columbia. Exposure to environmental conditions such as water mixed with road salt may cause the front fuel tank strap frame "T-Slot" bracket to corrode, possibly causing the fuel tank to drop and make contact with the ground.
Consequence & remedy
Consequence: If the fuel tank were to drop and contact the ground, a fuel leak may result. Additionally, in the event of a crash, the fuel tank may not remain secured to the vehicle, possibly causing a fuel leak. A fuel leak in the presence in an ignition source, can increase the risk of a fire.
Remedy: Chrysler will notify owners and dealers will bolt a bracket reinforcement to the frame, free of charge. The recall began May 2, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U04.
17V821000 · Power Train:automatic Transmission:lever And Linkage:column Shift
Dec 20, 2017
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
Consequence & remedy
Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
13V038000 · Power Train:driveline:differential Unit
Feb 6, 2013
Chrysler is recalling certain model year 2009-2012 Ram 1500 trucks manufactured from February 27, 2008, through June 30, 2009, and from December 1, 2009, through October 20, 2011; model year 2009-2011 Dodge Dakota trucks manufactured from February 27, 2007, through June 30, 2009, and from December 1, 2009, through September 30, 2011; model year 2009 Chrysler Aspen trucks manufactured from January 3, 2008, through December 18, 2008; and model year 2009 Dodge Durango trucks manufactured from January 3, 2008, through December 18, 2008. The rear axle pinion nut may loosen due to an undersized pinion spline that can allow relative motion between the nut and companion flange.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: On November 7, 2013 Chrysler notified owners that dealers would install a pinion nut retainer, free of charge. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N08.
12V474000 · Power Train:driveline:differential Unit
Oct 2, 2012
Chrysler is recalling certain model year 2009-2010, Ram 1500 and Dodge Dakota trucks, manufactured from July 1, 2009, through November 30, 2009, because the rear axle pinion nut may loosen due to a lack of adhesive.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: Chrysler will notify owners, and dealers will install a pinion nut retainer, free of charge. The recall began on June 17, 2013. Owners may contact Chrysler at 1-800-247-9753.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA19001 · Electrical Overstress
Opened Apr 19, 2019 · Closed Sep 19, 2024
Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.