SkipThatYearREAL DATA. SMARTER CAR DECISIONS.
← New search

2009 Dodge RAM 1500

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2009 Dodge RAM 1500 do not stand out strongly from the model-year median of 520.

About this comparison →
670Owner complaints

Model-year median: 520

2Recall campaigns

View recall details →

2Investigations

View investigation details →

How this year compares

Owner complaints by model year

Other model years Selected year
792
2006517
2007554
2008670
2009486
2010688
2011697
2012
Compare all RAM 1500 years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

Power Train
231Electrical System
97Unknown Or Other
52Engine
50Wheels
50
All reported categories
Structure
41Tires
36Air Bags
34Suspension
34Fuel/propulsion System
33Visibility/wiper
30Service Brakes
28Steering
28Visibility
28Exterior Lighting
19Electronic Stability Control (esc)
15Vehicle Speed Control
12Fuel System, Gasoline
10Engine And Engine Cooling
9Equipment
9Seats
8Seat Belts
6Service Brakes, Hydraulic
6Latches/locks/linkages
5Equipment Adaptive/mobility
2Traction Control System
1

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

542 reports with mileage · 128 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Power Train. Review the 231 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 97 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 50 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

29 crash reports2 fire reports18 injury reports

What owners actually said

670 reports
75,000 miles · Apr 1, 2015
Electrical SystemUnknown Or Other

THERE IS A BANGING NOISE THAT SEEMS TO BE COMING FROM BEHIND THE GLOVE BOX. I RESEARCHED IT ONLINE AND THINK IT'S A HEAT BLEND DOOR ACTUATOR THAT WENT OUT. I WAS QUOTED OVER $500 FOR THE REPAIR DUE TO THE COMPLEXITY OF GETTING TO THE ISSUE THROUGH THE DASHBAORD. A WHILE BACK THERE WAS A RECALL ON SOME PART OF THE AC/HEATING BUT…

Read full complaint

THERE IS A BANGING NOISE THAT SEEMS TO BE COMING FROM BEHIND THE GLOVE BOX. I RESEARCHED IT ONLINE AND THINK IT'S A HEAT BLEND DOOR ACTUATOR THAT WENT OUT. I WAS QUOTED OVER $500 FOR THE REPAIR DUE TO THE COMPLEXITY OF GETTING TO THE ISSUE THROUGH THE DASHBAORD. A WHILE BACK THERE WAS A RECALL ON SOME PART OF THE AC/HEATING BUT I CANNOT REMEMBER WHAT IS WAS FOR. I CALLED THEIR HOTLINE AND WAS ADVISED THAT RECALLS ARE ACTIVE FOR 10 YEARS FROM THE MANUFACTURE DATE, SO IN MY CASE, THROUGH 2019. I SEARCHED WWW.SAFERCAR.GOV AND THERE WASN'T ANY RECALLS LISTED UNVER THIS VIN. I READ THAT OTHERS ARE HAVING THIS SAME ISSUE AND I FEEL THIS IS A DEFECTIVE PART THAT SHOULD BE RECALLED AS AT ONE POINT IT DISABLED THE BLOWER. THE BLOWER OPERATED INTERMITTENTLY WHICH WAS EXTREMELY HAZARDOUS DURING WINTER. *TR

NHTSA ODI #10703110

145,000 miles · Mar 27, 2015
Tires

TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT THE TPMS WARNING LIGHT ILLUMINATED. ALSO, WHILE DRIVING AT HIGH SPEEDS, THE FRONT PASSENGER AND THE REAR DRIVER SIDE TIRE VALVES FRACTURED ON TWO OCCASIONS. AS A RESULT, BOTH TIRES BECAME FLAT. THE VEHICLE WAS TOWED TO THE DEALER TWICE WHO REPAIRED THE VALVES AN…

Read full complaint

TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT THE TPMS WARNING LIGHT ILLUMINATED. ALSO, WHILE DRIVING AT HIGH SPEEDS, THE FRONT PASSENGER AND THE REAR DRIVER SIDE TIRE VALVES FRACTURED ON TWO OCCASIONS. AS A RESULT, BOTH TIRES BECAME FLAT. THE VEHICLE WAS TOWED TO THE DEALER TWICE WHO REPAIRED THE VALVES AND REPLACED THE TIRES, BUT THE TPMS WARNING LIGHT REMAINED ILLUMINATED. IN ADDITION, WHILE DRIVING AT 70 MPH, THE DRIVER SIDE TIRE VALVE FRACTURED AND THE TIRE WENT FLAT. THE VEHICLE WAS TOWED TO THE DEALER, WHO AGAIN REPLACED THE TIRE AND THE VALVES. THE VEHICLE WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 13V038000 (POWER TRAIN), BUT THE PART WAS NOT AVAILABLE. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 145,000.

NHTSA ODI #10702150

86,100 miles · Mar 25, 2015
StructureVisibility

MY 2009 DODGE RAM 1500 IS MAKING A BANGING SOUND BEHIND THE GLOVE BOX. I HAVE HAD THIS ISSUE BEFORE SINCE IT WAS AN HEAT BLEND DOOR ACTUATOR THAT WENT OUT. THE DEALERSHIP FIXED IT ONCE AND NOW ITS BACK AGAIN. IS THIS GOING TO BE AN ON GOING ISSUE EACH YEAR AND THE PART NEEDS TO BE REPLACED. I WAS QUOTED ALMOST "$750" IN JUST…

Read full complaint

MY 2009 DODGE RAM 1500 IS MAKING A BANGING SOUND BEHIND THE GLOVE BOX. I HAVE HAD THIS ISSUE BEFORE SINCE IT WAS AN HEAT BLEND DOOR ACTUATOR THAT WENT OUT. THE DEALERSHIP FIXED IT ONCE AND NOW ITS BACK AGAIN. IS THIS GOING TO BE AN ON GOING ISSUE EACH YEAR AND THE PART NEEDS TO BE REPLACED. I WAS QUOTED ALMOST "$750" IN JUST LABOR FEES TO GET IT CHANGED OUT. I DON'T THINK THIS IS AN ISSUE ON MY END SINCE THE PART APPEARS TO LAST FOR A YEAR. I WILL CONTINUE TO MONITOR THE A/C AND CHECK WITH OTHER DODGE RAM FORUMS ON HOW OTHERS HAD THIS SOLVED. *TR

NHTSA ODI #10701746

81,000 miles · Mar 23, 2015
Wheels

DRIVING DOWN HIGHWAY AND TRUCK STARTED TO CHIME FOR A LOW TIRE PRESSURE. I IMMEDIATELY STOPPED AND FOUND THE VALVE STEM WAS INSIDE THE TIRE. I TOOK THE TIRE OFF THE RIM AND FOUND THE NUT THAT HOLDS THE TPS SENSOR IN THE TIRE OR THE VALVE STEM NUT WAS BROKE. I LOOKED AT THE OTHER TIRES ON MY TRUCK AND ALL OF THE NUTS ON THE TP…

Read full complaint

DRIVING DOWN HIGHWAY AND TRUCK STARTED TO CHIME FOR A LOW TIRE PRESSURE. I IMMEDIATELY STOPPED AND FOUND THE VALVE STEM WAS INSIDE THE TIRE. I TOOK THE TIRE OFF THE RIM AND FOUND THE NUT THAT HOLDS THE TPS SENSOR IN THE TIRE OR THE VALVE STEM NUT WAS BROKE. I LOOKED AT THE OTHER TIRES ON MY TRUCK AND ALL OF THE NUTS ON THE TPS SENSORS ARE CRACKED. THIS NOW IS THE SECOND TIME THIS HAS HAPPENED IN ROUGHLY A YEAR. THE FIRST TIME IT WAS SERVICED AT A TIRE SHOP AND NOW IT HAPPENED AGAIN AND I KNEW WHAT IT WAS RIGHT AWAY AND SERVICED IT MYSELF. *TR

NHTSA ODI #10701141

Mileage unknown · Mar 23, 2015
Power Train

DODGE RAM 1500. LEGAL REPRESENTATION FOR CONSUMER WRITES IN REGARDS TO REAR AXLE FAILURE. *SMD A SCREW LOOSENED AT THE REAR AXLE. *JB

NHTSA ODI #10680232

Mileage unknown · Mar 16, 2015
Electrical SystemPower Train

STARTED DRIVING TRUCK AND ALL GAUGES WENT BLANK INCLUDING SPEEDOMETER. WARNING LIGHTS FOR AIR BAG, CHECK ENGINE, LOW TIRE PRESSURE, BRAKES, ETC. ALL CAME ON AS WELL AS WIPERS STARTED WORKING WITH SWITCH IN OFF POSITION! *TR

NHTSA ODI #10694669

45,000 miles · Mar 11, 2015
Wheels

TL*THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT WHILE DRIVING AT APPROXIMATELY 15 MPH, THERE WAS AN ABNORMAL NOISE AND THE FRONT PASSENGER SIDE TIRE DETACHED FROM THE VEHICLE WITHOUT WARNING. THE VEHICLE WAS TAKEN TO A DEALER. THE TECHNICIAN DIAGNOSED THAT THE SCREWS IN THE TIRE LOOSENED AND NEEDED TO BE REPLA…

Read full complaint

TL*THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT WHILE DRIVING AT APPROXIMATELY 15 MPH, THERE WAS AN ABNORMAL NOISE AND THE FRONT PASSENGER SIDE TIRE DETACHED FROM THE VEHICLE WITHOUT WARNING. THE VEHICLE WAS TAKEN TO A DEALER. THE TECHNICIAN DIAGNOSED THAT THE SCREWS IN THE TIRE LOOSENED AND NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 45,000.

NHTSA ODI #10693560

Mileage unknown · Mar 10, 2015
Power Train

TL*THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN ID NUMBER: 13V038000 (POWER TRAIN) AND STATED THAT THE PARTS WERE NOT AVAILABLE. THE DEALER DID NOT PROVIDE A SPECIFIC DATE FOR WHEN THE PARTS WOULD BECOME AVAILABLE. THE MANUFACTURER WAS CONTACTED AND COULD NOT PROVIDE AN ESTIMATED DA…

Read full complaint

TL*THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN ID NUMBER: 13V038000 (POWER TRAIN) AND STATED THAT THE PARTS WERE NOT AVAILABLE. THE DEALER DID NOT PROVIDE A SPECIFIC DATE FOR WHEN THE PARTS WOULD BECOME AVAILABLE. THE MANUFACTURER WAS CONTACTED AND COULD NOT PROVIDE AN ESTIMATED DATE FOR WHEN THE VEHICLE WOULD RECEIVE THE RECALL REPAIRS. THE CONTACT WAS NOT EXPERIENCING A FAILURE.

NHTSA ODI #10693272

60,000 miles · Mar 6, 2015
SuspensionFire

TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 65 MPH, SMOKE STARTED TO EMIT FROM THE FRONT END OF THE VEHICLE. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC, WHO DIAGNOSED THAT THE FRONT WHEEL BEARING NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS MADE A…

Read full complaint

TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 65 MPH, SMOKE STARTED TO EMIT FROM THE FRONT END OF THE VEHICLE. THE VEHICLE WAS TOWED TO AN INDEPENDENT MECHANIC, WHO DIAGNOSED THAT THE FRONT WHEEL BEARING NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VIN WAS UNAVAILABLE. THE APPROXIMATE FAILURE MILEAGE WAS 60,000.

NHTSA ODI #10692425

80,900 miles · Mar 3, 2015
Suspension

TL*THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED WHILE DRIVING APPROXIMATELY 65 MPH, A LOUD GRINDING NOISE EMITTED OUTSIDE OF THE VEHICLE. THE VEHICLE WAS MANEUVERED TO THE SIDE OF THE ROAD AND THE REAR WHEELS SEIZED. THE VEHICLE WAS TOWED TO AN INDEPENDENT. THE MANUFACTURER WAS NOT NOTIFIED OF THE PROBLEM. THE APPR…

Read full complaint

TL*THE CONTACT OWNS A 2009 DODGE RAM 1500. THE CONTACT STATED WHILE DRIVING APPROXIMATELY 65 MPH, A LOUD GRINDING NOISE EMITTED OUTSIDE OF THE VEHICLE. THE VEHICLE WAS MANEUVERED TO THE SIDE OF THE ROAD AND THE REAR WHEELS SEIZED. THE VEHICLE WAS TOWED TO AN INDEPENDENT. THE MANUFACTURER WAS NOT NOTIFIED OF THE PROBLEM. THE APPROXIMATE FAILURE MILEAGE WAS 80,900. THE VIN WAS UNAVAILABLE.

NHTSA ODI #10691748

Official recalls

2

13V038000 · Power Train:driveline:differential Unit

Feb 6, 2013

Chrysler is recalling certain model year 2009-2012 Ram 1500 trucks manufactured from February 27, 2008, through June 30, 2009, and from December 1, 2009, through October 20, 2011; model year 2009-2011 Dodge Dakota trucks manufactured from February 27, 2007, through June 30, 2009, and from December 1, 2009, through September 30, 2011; model year 2009 Chrysler Aspen trucks manufactured from January 3, 2008, through December 18, 2008; and model year 2009 Dodge Durango trucks manufactured from January 3, 2008, through December 18, 2008. The rear axle pinion nut may loosen due to an undersized pinion spline that can allow relative motion between the nut and companion flange.

Consequence & remedy

Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.

Remedy: On November 7, 2013 Chrysler notified owners that dealers would install a pinion nut retainer, free of charge. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N08.

12V474000 · Power Train:driveline:differential Unit

Oct 2, 2012

Chrysler is recalling certain model year 2009-2010, Ram 1500 and Dodge Dakota trucks, manufactured from July 1, 2009, through November 30, 2009, because the rear axle pinion nut may loosen due to a lack of adhesive.

Consequence & remedy

Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.

Remedy: Chrysler will notify owners, and dealers will install a pinion nut retainer, free of charge. The recall began on June 17, 2013. Owners may contact Chrysler at 1-800-247-9753.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

DP14004 · Totally Integrated Power Module Failure

Opened Sep 25, 2014 · Closed Jul 24, 2015

Status: closed (inferred from source dates) · Electrical System

In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den

PE12021 · Rear Differential Failure

Opened Jul 19, 2012 · Closed Mar 5, 2013

Status: closed (inferred from source dates) · Power Train; Power Train:automatic Transmission; Power Train:axle Assembly; Power Train:driveline; Power Train:driveline:differential Unit; Power Train:driveline:driveshaft; Power Train:transfer Case (4-WHEEL Drive)

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Additional source detail variants (14)

Power Train:automatic Transmission

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:automatic Transmission

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:axle Assembly

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:axle Assembly

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:driveline

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:driveline

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:driveline:differential Unit

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:driveline:differential Unit

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:driveline:driveshaft

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:driveline:driveshaft

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:transfer Case (4-WHEEL Drive)

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440

Power Train:transfer Case (4-WHEEL Drive)

In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440