IllustrationBLEND DOOR ACTUATOR AND BLEND DOOR GEAR BOX FAILED REPEATEDLY CHANGING HOT AIR FROM AC UNIT TO COLD AIR OR VISE VERSA.
2009 Dodge RAM 1500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Dodge RAM 1500 do not stand out strongly from the model-year median of 520.
About this comparison →How this year compares
Owner complaints by model year
Compare all RAM 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
740–25K
10725–50K
13150–75K
10475–100K
94100–150K
32150K+
542 reports with mileage · 128 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 231 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 97 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 50 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports2 fire reports18 injury reports
What owners actually said
670 reportsTWO TIRE VALVE STEMS HAVE FAILED CAUSING SUDDEN LOSS OF TIRE INFLATION. FIRST FAILURE, JUNE 5, 2016 DRIVER SIDE REAR TIRE OCCURRED ON INTERSTATE HIGHWAY (70MPH). TIRE WAS DAMAGED BEYOND REPAIR BEFORE VEHICLE STOPPED. SECOND FAILURE, SEPT 26, 2016 PASSENGER SIDE REAR TIRE OCCURRED ON STATE HIGHWAY (55MPH). TIRE HAS NOT BEEN …
Read full complaint
TWO TIRE VALVE STEMS HAVE FAILED CAUSING SUDDEN LOSS OF TIRE INFLATION. FIRST FAILURE, JUNE 5, 2016 DRIVER SIDE REAR TIRE OCCURRED ON INTERSTATE HIGHWAY (70MPH). TIRE WAS DAMAGED BEYOND REPAIR BEFORE VEHICLE STOPPED. SECOND FAILURE, SEPT 26, 2016 PASSENGER SIDE REAR TIRE OCCURRED ON STATE HIGHWAY (55MPH). TIRE HAS NOT BEEN REVIEWED FOR INTERNAL DAMAGE. FRONT DRIVER SIDE TIRE SHOWS CRACK IN VALVE STEM RETAINING NUT. CRACK RUNS STRAIGHT FROM TIRE TO TOP OF RETAINING NUT. CRACK APPEARANCE LOOKS AS THOUGH THE RETAINING NUT IS A STAMPED PART WITH A SEAM. PHOTOS: 1) SEPT 26 FAILURE SHOWING VALVE STEM PARTS COMPLETELY MISSING. 2) UNFAILED, BUT CRACKED RETAINING NUT (DARK LINE IS CRACK) TAKING TRUCK TO TIRE SHOP FOR REPLACEMENT OF ALL VALVE STEMS. WILL ASK FOR ALL EXISTING PARTS TO BE RETURNED. NOTE FIRST FAILURE REQUIRED CHANGING TIRE WITHIN 4 FEET OF HEAVY VEHICLE TRAFFIC MOVING AT 70 MPH SPEED LIMIT. SECOND FAILURE REQUIRED CHANGING TIRE ON DARK ROADWAY DURING RAIN STORM. UNLIKE TYPICAL TIRE PUNCTURES WITH SLOW PRESSURE LOSS, I HAD NO ABILITY TO RE-INFLATE AND MOVE TO SAFER LOCATION FOR TIRE CHANGING.
2009 DODGE RAM 1500 THERE IS A MANIFOLD BOLT THAT IS INFERIOR/DEFECTIVE PART DEALERSHIP HAS ADMITTED THEY KNOW IT IS.. THEY ARE REPLACING ATLEAST ONE A WEEK. THIS BOLT CAN BREAK OFF AND CAUSE THE MOTOR TO CEASE... WARRANTY WILL NOT REPLACE AND THIS IS HAPPENING TO HUNDREDS OF PEOPLE ITS IN ALL DODGE FORUMS... $400 + TO REPLACE …
Read full complaint
2009 DODGE RAM 1500 THERE IS A MANIFOLD BOLT THAT IS INFERIOR/DEFECTIVE PART DEALERSHIP HAS ADMITTED THEY KNOW IT IS.. THEY ARE REPLACING ATLEAST ONE A WEEK. THIS BOLT CAN BREAK OFF AND CAUSE THE MOTOR TO CEASE... WARRANTY WILL NOT REPLACE AND THIS IS HAPPENING TO HUNDREDS OF PEOPLE ITS IN ALL DODGE FORUMS... $400 + TO REPLACE THIS DEFINITELY NEEDS TO BD A RECALL ONLY 50,000 MILES ON TRUCK
TIRE AIR VALVES ARE METAL AND SPLIT CAUSING A BLOWOUT ON I-57 AT 65 MPH. AND AS OF TODAY 09/03/2016 I HAVE NOTICED THE TIRES (ALL 4) ARE STARTING TO LOOSE AIR AND 3 OUT OF 4 VALVE STEMS ARE CRACKED CAUSING THE AIR TO RUSH OUT OF THE TIRE AS THE CRACK GETS WORSE ,THIS IS VERY MUCH A SAFETY HAZARD. AT THIS POINT I HAVE NO WAY TO …
Read full complaint
TIRE AIR VALVES ARE METAL AND SPLIT CAUSING A BLOWOUT ON I-57 AT 65 MPH. AND AS OF TODAY 09/03/2016 I HAVE NOTICED THE TIRES (ALL 4) ARE STARTING TO LOOSE AIR AND 3 OUT OF 4 VALVE STEMS ARE CRACKED CAUSING THE AIR TO RUSH OUT OF THE TIRE AS THE CRACK GETS WORSE ,THIS IS VERY MUCH A SAFETY HAZARD. AT THIS POINT I HAVE NO WAY TO SCAN IN THE PAPERWORK FROM THE REPAIR SHOP, BUT I DO HAVE IT.
TRUCK IS MAKING A LOUD WHINING NOISE THAT SEEMS TO BE COMING FROM THE REAR END AND THE FRONT GAS TANK STRAP HAS COME LOOSE FROM THE FRAME. THE SLOT THAT IT IS SUPPOSED TO BE FASTENED TO IS RUSTED COMPLETELY OUT. THIS IS A SEVERE SAFETY HAZZARD THAT COULD BE VERY DEADLY IF THE TANK COMES OFF. UPDATED 08/11/17 *BF *CN
I WAS DRIVING MY 2009 RAM 1500 HOME FROM WORK AND I HEARD A NOISE FROM THE BACK OVER BUMPS, AND WHEN STOPPING. I BROUGHT IT INTO THE SHOP THE NEXT MORNING AND DISCOVERED THE FRONT OF FUEL TANK WAS HANGING DOWN, THIS WAS DUE TO THE FRAME RUSTING OUT WHERE THE FUEL TANK STRAP ATTACHED. ALSO INSPECTED WAS THE FRAME WHERE THE REAR…
Read full complaint
I WAS DRIVING MY 2009 RAM 1500 HOME FROM WORK AND I HEARD A NOISE FROM THE BACK OVER BUMPS, AND WHEN STOPPING. I BROUGHT IT INTO THE SHOP THE NEXT MORNING AND DISCOVERED THE FRONT OF FUEL TANK WAS HANGING DOWN, THIS WAS DUE TO THE FRAME RUSTING OUT WHERE THE FUEL TANK STRAP ATTACHED. ALSO INSPECTED WAS THE FRAME WHERE THE REAR STRAP ATTACHED IS ALSO ALMOST RUSTED THROUGH. I DID A SEARCH ONLINE AND FOUND OUT THERE WAS MANY OWNERS WITH THE SAME COMPLAINT
I MAILED A COMPLAINT NOTICE AND YOU CLAIM SOMEONE WILL GET BACK WITH YOU IN 2 BUSINESS DAYS---I'M STILL WAITING FOR A RESPONSE ON # 10896888 AND # 10896617. OUR SAFETY SHOULD BE YOUR UTMOST IMPORTANCE. HOW CAN WE HAVE OUR VEHICLES REPLACED IF THERE ARE NO PARTS, AND IF WE CHOOSE TO HAVE THIS FIXED OURSELVES, WE ARE GOUGED IN …
Read full complaint
I MAILED A COMPLAINT NOTICE AND YOU CLAIM SOMEONE WILL GET BACK WITH YOU IN 2 BUSINESS DAYS---I'M STILL WAITING FOR A RESPONSE ON # 10896888 AND # 10896617. OUR SAFETY SHOULD BE YOUR UTMOST IMPORTANCE. HOW CAN WE HAVE OUR VEHICLES REPLACED IF THERE ARE NO PARTS, AND IF WE CHOOSE TO HAVE THIS FIXED OURSELVES, WE ARE GOUGED IN A BIDDING WAR AND PAY A PREMIUM PRICE FOR THE PART. HOW DO WE KNOW IF OUR VEHICLE IS ACTUALLY BEING FIXED OR NOT? THERE NEEDS TO BE AN INTERNAL INVESTIGATION..... [XXX]. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6). *TR
TEAM: THE EMERGENCY PARKING BRAKE LEVERS LOCATED IN REAR ROTORS CORRODED & LOCKED UP PREVENTING USAGE. I NOTICED THIS BECAUSE THE CABLE WAS DROOPING & BANGING AGAINST THE FRAME.
TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. WHILE DRIVING VARIOUS SPEEDS, THE REAR DIFFERENTIAL LOCKED UP ON THE VEHICLE. THE VEHICLE WAS TOWED TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE REAR DIFFERENTIAL FAILED, BUT WAS PREVIOUSLY REPAIRED PER NHTSA CAMPAIGN NUMBER: 13V038000 (POWER TRAIN). THE REMEDY FAILED TO REPAIR THE VE…
Read full complaint
TL* THE CONTACT OWNS A 2009 DODGE RAM 1500. WHILE DRIVING VARIOUS SPEEDS, THE REAR DIFFERENTIAL LOCKED UP ON THE VEHICLE. THE VEHICLE WAS TOWED TO THE DEALER WHERE IT WAS DIAGNOSED THAT THE REAR DIFFERENTIAL FAILED, BUT WAS PREVIOUSLY REPAIRED PER NHTSA CAMPAIGN NUMBER: 13V038000 (POWER TRAIN). THE REMEDY FAILED TO REPAIR THE VEHICLE. THE MANUFACTURER STATED THAT THE VEHICLE WAS PREVIOUSLY REPAIRED OUT OF STATE, BUT THE CONTACT HAD NO RECOLLECTION OF THE REPAIR. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 119,000. UPDATED 10/05/16*LJ *TR
THE FRAME ROTTED OUT WERE THE STRAP FOR THE FUEL TANK ATTACHES TO THE FRAME CAUSING THE FUEL TANK TO DROP. I HAD TO REATTACH FUEL TANK WITH A RATCHET STRAP TO DRIVE THE TRUCK HOME. UPDATED 08/11/17 *BF *CN
Official recalls
213V038000 · Power Train:driveline:differential Unit
Feb 6, 2013
Chrysler is recalling certain model year 2009-2012 Ram 1500 trucks manufactured from February 27, 2008, through June 30, 2009, and from December 1, 2009, through October 20, 2011; model year 2009-2011 Dodge Dakota trucks manufactured from February 27, 2007, through June 30, 2009, and from December 1, 2009, through September 30, 2011; model year 2009 Chrysler Aspen trucks manufactured from January 3, 2008, through December 18, 2008; and model year 2009 Dodge Durango trucks manufactured from January 3, 2008, through December 18, 2008. The rear axle pinion nut may loosen due to an undersized pinion spline that can allow relative motion between the nut and companion flange.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: On November 7, 2013 Chrysler notified owners that dealers would install a pinion nut retainer, free of charge. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N08.
12V474000 · Power Train:driveline:differential Unit
Oct 2, 2012
Chrysler is recalling certain model year 2009-2010, Ram 1500 and Dodge Dakota trucks, manufactured from July 1, 2009, through November 30, 2009, because the rear axle pinion nut may loosen due to a lack of adhesive.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: Chrysler will notify owners, and dealers will install a pinion nut retainer, free of charge. The recall began on June 17, 2013. Owners may contact Chrysler at 1-800-247-9753.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2DP14004 · Totally Integrated Power Module Failure
Opened Sep 25, 2014 · Closed Jul 24, 2015
Status: closed (inferred from source dates) · Electrical System
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
PE12021 · Rear Differential Failure
Opened Jul 19, 2012 · Closed Mar 5, 2013
Status: closed (inferred from source dates) · Power Train; Power Train:automatic Transmission; Power Train:axle Assembly; Power Train:driveline; Power Train:driveline:differential Unit; Power Train:driveline:driveshaft; Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Additional source detail variants (14)
Power Train:automatic Transmission
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:automatic Transmission
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:axle Assembly
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:axle Assembly
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:differential Unit
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:differential Unit
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:driveshaft
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:driveshaft
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440