IllustrationCARFAX GOT THE WRONG MILEAGE 1 HAVE 185292 AND I CAN SEND PICTURES
2009 Dodge RAM 1500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Dodge RAM 1500 do not stand out strongly from the model-year median of 520.
About this comparison →How this year compares
Owner complaints by model year
Compare all RAM 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
740–25K
10725–50K
13150–75K
10475–100K
94100–150K
32150K+
542 reports with mileage · 128 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 231 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 97 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 50 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports2 fire reports18 injury reports
Unknown Or Other complaints
52 reportsThe rear axle pinion nut came off and the rear axle locked up. Driveshaft dropped to the street, breaking the transfer case. Incident resulted in an immediate loss of control. Driver behind me saw the driveshaft fall and braked to avoid contact with my vehicle. Luckily, I was driving about 25 miles per hour and was able to c…
Read full complaint
The rear axle pinion nut came off and the rear axle locked up. Driveshaft dropped to the street, breaking the transfer case. Incident resulted in an immediate loss of control. Driver behind me saw the driveshaft fall and braked to avoid contact with my vehicle. Luckily, I was driving about 25 miles per hour and was able to come to a stop on the roadside without wrecking. I later learned that in late 2015, Chrysler was supposed to notify owners of the defect concerning the rear axle pinion nut. I never received that notification or any other recall notice regarding my vehicle. The local Dodge dealer has told me to have my vehicle towed to them. They said the damage will be evaluated and Chrysler will determine if they should pay for the necessary repairs. I believe they should, since I was never notified of the problem with the rear axle pinion nut. The consumer stated the District Manager at the dealership refused to repair the vehicle. The reasons for not repairing the vehicle were the necessary parts couldn't be found, the recall was too long ago, and you should have brought it in for repairs earlier when the recall notice went out.
CLICKING NOISE UNDER DASH EVEN WHEN THE TRUCK IS OFF, NO HEAT, STEAMING UP WINDOW, CHECKED HEATER CORE AND ITS GOOD HAD THE WHOLE SYSTEM FLUSHED. STILL NOT RITE. ALSO CRUZE CONTROL NOT WORKING.
THE HEATER DOES NOT WORK AND I WAS TOLD BY DODGE DEALER MECHANIC THAT THE MAIN HOUSING UNIT DOOR FOR THE HEATER AND AC USUALLY BREAKS.
TRUCK SOMETIMES SHOWS LIFE WHEN IN ACCESSORY BUT WHEN PUT TO ON TRUCK DIES COMPLETELY, OBVIOUSLY NOT GOING TO TURN OVER WITH NO SIGN OF LIFE. MINUTES LATER I CAN COME BACK AND START IT NO PROBLEM. HEADLIGHTS WILL CONSISTENTLY STUTTER OR EVEN TURN ON OR OFF WHILE PARKED OR MOVING. LASTLY WHILE DRIVING SOMETIMES ALL POWER AND ELEC…
Read full complaint
TRUCK SOMETIMES SHOWS LIFE WHEN IN ACCESSORY BUT WHEN PUT TO ON TRUCK DIES COMPLETELY, OBVIOUSLY NOT GOING TO TURN OVER WITH NO SIGN OF LIFE. MINUTES LATER I CAN COME BACK AND START IT NO PROBLEM. HEADLIGHTS WILL CONSISTENTLY STUTTER OR EVEN TURN ON OR OFF WHILE PARKED OR MOVING. LASTLY WHILE DRIVING SOMETIMES ALL POWER AND ELECTRICAL SHUTS OFF AND TRUCK IS COMPLETELY DEAD WHILE GOING ANY SPEED. I HAVE NOT FOUND A CERTAIN SPEED IT DIES BECAUSE IT HAS SHUT OFF IN PARKING LOTS AND GOING DOWN HIGHWAY. POWER STEERING IS GONE AND ITS SCARY TO PULL OF SIDE OF ROAD WHEN SOME ROADS DON'T HAVE MUCH TO WORK WITH OR GOING AT HIGHWAY SPEEDS AND LOSING ALL POWER.
VEHICLE POWER FAILURE WHILE MOVING ON THREE OCCASIONS. VEHICLE LOSES ALL POWER INCLUDING STEERING. HAVE ALREADY REPLACED SEVERAL SENSORS AND THE PCM WITH NO SUCCESS. VERY HAZARDOUS TO ME AND ALL MOTORISTS AROUND ME.
THE TIPM HAS GONE UP WITH LESS THAN 100,000 MILES ON THE TRUCK AND ITS VERY COSTLY ALSO I HAVE TO KEEP REPLACING THE BLEND DOOR ACTUATOR I HAVE DONE THIS LIKE 4 TIMES ITS A LOT OF MONEY AND A HASSLE WHY HAVENT THESE THINGS BEEN RECALLED
THERE WAS A CLICKING NOISE BEHIND THE DASH OF MY TRUCK. TOOK IT IN TO GET IT LOOKED AT AND IT WAS THE ACTUATOR BEHIND MY HVAC THAT NEEDED TO BE REPLACED. AFTER SOME RESEARCH I FOUND THERE WAS A RECALL THE K17 THAT HAD BEEN DONE THAT WAS SUPPOSE TO FIX THIS ISSUE APPARENTLY. AFTER TALKING WITH THE DEALERSHIP AND MAKING CALLS TO R…
Read full complaint
THERE WAS A CLICKING NOISE BEHIND THE DASH OF MY TRUCK. TOOK IT IN TO GET IT LOOKED AT AND IT WAS THE ACTUATOR BEHIND MY HVAC THAT NEEDED TO BE REPLACED. AFTER SOME RESEARCH I FOUND THERE WAS A RECALL THE K17 THAT HAD BEEN DONE THAT WAS SUPPOSE TO FIX THIS ISSUE APPARENTLY. AFTER TALKING WITH THE DEALERSHIP AND MAKING CALLS TO RAM THEY TOLD ME THAT IT WOULDN'T BE FIXED FOR FREE DUE TO THE FACT THE K17 WASN'T AN ACTUAL RECALL AND JUST A CUSTOMER SATISFACTION LETTER. THEY QUOTED ME AT $1500 DUE TO THE FACT THE DASH HAD TO BE REMOVED TO GET TO THIS ACTUATOR AND SUGGESTED I REPLACE ALL OF THEM IF I WAS GOING TO HAVE THIS FIXED. I FEEL LIKE THIS IS WRONG AND THEY SHOULD FIX IT AGAIN. AT THIS POINT I DON'T KNOW WHAT TO DO SINCE THE MANUFACTURER TOLD ME IT WOULDN'T BE COVERED.
THE FRONT WINDSHIELD SEALS ON THE SIDES ARE STARTING TO COME OFF. WORRIED THAT I CAN NOT DRIVE ON HIGHWAYS OR INTERSTATE FEARING THAT MY WINDSHIELD WILL FLY OFF. MANOR SAFETY HAZARD.
2009 DODGE RAM 1500. WHEN THE VEHICLE WAS STARTED, A TICKING NOISE WAS HEARD FROM THE EXHAUST MANIFOLD. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT BOTH SIDES OF THE ENGINE BLOCK HINGES WERE FRACTURED AND NEEDED REPLACEMENT. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE VIN WAS U…
Read full complaint
2009 DODGE RAM 1500. WHEN THE VEHICLE WAS STARTED, A TICKING NOISE WAS HEARD FROM THE EXHAUST MANIFOLD. THE VEHICLE WAS TAKEN TO THE DEALER WHERE IT WAS DIAGNOSED THAT BOTH SIDES OF THE ENGINE BLOCK HINGES WERE FRACTURED AND NEEDED REPLACEMENT. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE VIN WAS UNKNOWN. THE APPROXIMATE FAILURE MILEAGE WAS 80000
Official recalls
213V038000 · Power Train:driveline:differential Unit
Feb 6, 2013
Chrysler is recalling certain model year 2009-2012 Ram 1500 trucks manufactured from February 27, 2008, through June 30, 2009, and from December 1, 2009, through October 20, 2011; model year 2009-2011 Dodge Dakota trucks manufactured from February 27, 2007, through June 30, 2009, and from December 1, 2009, through September 30, 2011; model year 2009 Chrysler Aspen trucks manufactured from January 3, 2008, through December 18, 2008; and model year 2009 Dodge Durango trucks manufactured from January 3, 2008, through December 18, 2008. The rear axle pinion nut may loosen due to an undersized pinion spline that can allow relative motion between the nut and companion flange.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: On November 7, 2013 Chrysler notified owners that dealers would install a pinion nut retainer, free of charge. In July 2015, and under a consent order with NHTSA, the company agreed to offer owners three options for remedying their vehicles: perform the original remedy, offer to repurchase the vehicle at the fair market value plus 10%, or offer an additional incentive offer towards the purchase of a new Dodge, Jeep, Chrysler, or Fiat vehicle. Chrysler will notify owners of the new recall options in a letter expected to be mailed on August 31, 2015. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N08.
12V474000 · Power Train:driveline:differential Unit
Oct 2, 2012
Chrysler is recalling certain model year 2009-2010, Ram 1500 and Dodge Dakota trucks, manufactured from July 1, 2009, through November 30, 2009, because the rear axle pinion nut may loosen due to a lack of adhesive.
Consequence & remedy
Consequence: If the rear axle pinion nut loosens, the axle can lock up and cause a loss of vehicle control and/or a vehicle crash with little warning.
Remedy: Chrysler will notify owners, and dealers will install a pinion nut retainer, free of charge. The recall began on June 17, 2013. Owners may contact Chrysler at 1-800-247-9753.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2DP14004 · Totally Integrated Power Module Failure
Opened Sep 25, 2014 · Closed Jul 24, 2015
Status: closed (inferred from source dates) · Electrical System
In a letter dated August 21, 2014, the Center for Auto Safety (CAS) petitioned the National Highway Traffic Safety Administration (NHTSA) to initiate a defect investigation of alleged failures associated with the Totally Integrated Power Module (TIPM) installed in Chrysler SUV?s, trucks, and vans beginning in the 2007 model year. The petitioner alleges that TIPM defects may result in engine stall, airbag non-deployment, failure of fuel pump shutoff resulting in unintended acceleration, fire, and other symptoms. On September 25, 2014, the Office of Defects Investigation (ODI) opened DP14-004 to evaluate the petition for a grant or deny decision. ODI analyzed complaint data provided by CAS as well as complaints submitted to ODI from consumers. In total, there were 296 complaints submitted by the petitioner in the original petition and five supplements, including 271 complaints related to the subject vehicles equipped with TIPM-7. Approximately 3 percent of CAS complaints are related to vehicles equipped with TIPM-6 and ODI?s review of these complaints did not identify any safety defect trends. ODI conducted a detailed review of complaints narratives submitted by CAS and consumers including careful analysis of vehicle repair histories, warranty claims obtained from the manufacturer and any available Customer Assistance Inquiry reports (CAIR). Analysis of the field data indicated that MY2011-2013 Jeep Grand Cherokee and Dodge Durango vehicles exhibited significantly higher complaint rates related to fuel pump relay (FPR) failures than other subject vehicles. In a September 3, 2014 letter to NHTSA, Chrysler submitted a Defect Information Report (DIR) identifying a defect in the FPR within the TIPM-7 which can result in a no start or stall condition in approximately 188,723 model year (MY) 2011 Jeep Grand Cherokee (WK) and Dodge Durango (WD) vehicles manufactured from January 5, 2010 through July 20, 2011 (14V-530).In a February 24, 2015 letter, Chrysler submitted a second DIR expanding the scope of the FPR defect condition to include an additional 338,216 MY 2012 through 2013 Jeep Grand Cherokee vehicles manufactured from September 17, 2010 through August 19, 2013 and MY 2012 through 2013 Dodge Durango vehicles manufactured from January 18, 2011 through August 19, 2013 (15V-115).ODI analysis of the CAS allegations of TIPM defects resulting in stall while driving, airbag non-deployment, unintended acceleration, fire and other faults identified a single defect condition related to 1 of over 60 different circuits in the TIPM assembly. The most common effect of this defect condition, related to the fuel pump relay, was a no-start concern, but it could also result in stall while driving (76 complaints). No valid evidence was presented in support of claims related to airbag non-deployment, unintended acceleration or fire resulting from TIPM faults and these claims were found to be wholly without merit based on review of the field data and design of the relevant systems and components.Except insofar as the petitioner's contentions relate to the defect condition addressed by the Chrysler recalls, the factual bases of the petitioner's contentions that any further investigation is necessary are unsupported. In our view, additional investigation is unlikely to result in a finding that a defect related to motor vehicle safety exists or a NHTSA order for the notification and remedy of a safety-related defect as alleged by the petitioner at the conclusion of the requested investigation. Therefore, in view of the need to allocate and prioritize NHTSA's limited resources to best accomplish the agency's safety mission, the petition is den
PE12021 · Rear Differential Failure
Opened Jul 19, 2012 · Closed Mar 5, 2013
Status: closed (inferred from source dates) · Power Train; Power Train:automatic Transmission; Power Train:axle Assembly; Power Train:driveline; Power Train:driveline:differential Unit; Power Train:driveline:driveshaft; Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Additional source detail variants (14)
Power Train:automatic Transmission
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:automatic Transmission
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:axle Assembly
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:axle Assembly
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:differential Unit
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:differential Unit
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:driveshaft
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:driveline:driveshaft
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440
Power Train:transfer Case (4-WHEEL Drive)
In a letter dated October 2, 2012, Chrysler Group LLC (Chrysler) submitted a Defect Information Report (DIR) to NHTSA identifying a safety defect in approximately 48,058 vehicles built with an axle pinion nut that can loosen, which could result in lock-up of the rear axle and/or separation of the rear drive shaft from the rear axle (NHTSA Recall No. 12V-474).The vehicles involved in this recall are model year (MY) 2009 and MY 2010 Dodge Ram 1500 (46,677) and Dodge Dakota (1,381) vehicles manufactured between July 1, 2009 and November 30, 2009 built with 9.25? rear axles built at Chrysler?s Detroit Axle Assembly Plant.Chrysler stated it determined during this time frame there were instances of 9.25? axles built with rear axle pinion nuts that were missing the adhesive patch.The remedy for these vehicles is to install a pinion nut retainer.In a review of data in its complaint database and data submitted by Chrysler, the Office of Defects Investigation (ODI) identified 194 reports (including 3 crash reports) of rear axle lock up and/or drive shaft separation outside of the scope of recall 12V-474.In a letter dated February 5, 2013, Chrysler submitted a second DIR to NHTSA identifying another safety defect in approximately 278,150 vehicles built with 9.25? rear axles and outside of the scope of recall 12V-474 that could also result in lock-up of the rear axle and/or rear drive separation (NHTSARecall No. 13V-038).Chrysler stated that analysis of field return parts from this vehicle population, undersized pinion splines were found as the likely factor contributing to the loosening of the pinion nut.The vehicles involved in this recall are:266,091 MY 2009?2012 Dodge Ram 1500 vehicles manufactured from 2/28/09 through 6/30/09 and 12/1/09 through 10/20/11 (including 183,421 MY 2009-2010 subject vehicles); 8,475 MY 2009?2010 Dodge Dakota vehicles manufactured from 2/18/07 through 6/30/09 and 12/1/09 through 7/9/10; 2,346 MY 2009 Chrysler Aspen vehicles manufactured from 1/19/07 through 12/18/08; and 1,238 MY 2009 Dodge Durango vehicles manufactured from 1/17/07 through 12/18/08.The remedy for these vehicles is the same as for 12V-474.The failure counts in this resume are for the subject MY 2009-2010 Dodge Ram 1500 vehicles only.The recalled vehicle counts are based on current estimates from Chrysler and may differ from estimates in the original DIR's.This Preliminary Evaluation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10489593,10489091,10488952,10485174,10485096,10484596,10484490,10483394,10483370,10482853,10482816,10482438,10479806,10479352,10478724,10477460,10477354,10476923,10476691,10475939,10475241,10475158,10473147,10472488,10470655,10470516,10470231,10470152,10469969,10469548,10469435,10468759,10468024,10467819,10467805,10467683,10467196,10466630,10464240,10448778,10445208,10443542,10439902,10375394,10362531,10353440