IllustrationWHILE DRIVING ON THE HIGHWAY, THE HOOD TRIM COVERING THE COWL, BLEW OFF AND NEARLY STRUCK THE VEHICLE BEHIND. *TR
1999 Chrysler Lhs
Owner reports · Recalls · Investigations
More warning signs than most Lhs years
Owner complaints for the 1999 Chrysler Lhs are substantially higher than the model-year median of 50.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Lhs years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
50–25K
1325–50K
2350–75K
1375–100K
7100–150K
2150K+
63 reports with mileage · 102 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Vehicle Speed Control. Review the 25 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 19 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
29 crash reports2 fire reports17 injury reports
Structure complaints
16 reportsDRIVING ON I-393,WEST BOUND AT 60 MPH, IN THE RAIN, WHEN THE PLASTIC MOLDING ALONG THE HOOD OF '99 CHRYSLER LHS DETACHED AND HIT THE WINDSHIELD WIPERS CAUSING THE CAR TO SWERVE TOWARDS THE SIDE OF THE ROAD BED AND ALMOST CAUSING THE CAR TO OVER-TURN. *JB
DT*: THE CONTACT STATED WHILE DRIVING THE VEHICLE 57 MPH THE HOOD MOLDING BROKE AND FLEW ACROSS THE VEHICLE ON A BUSY INTERSTATE. THE VEHICLE WAS TAKEN TO THE DEALERSHIP HOWEVER, NO REPAIRS WERE MADE. THE MANUFACTURER HAS BEEN ALERTED. UPDATED 03/28/06. *JB
A PIECE OF TRIM LOCATED ON THE HOOD IN FRONT OF THE WINDSHIELD CAME OFF WHILE DRIVING 65 MPH AND COMMENCED TO FLAP AGAINST THE WINDSHIELD. CONSUMER HAD TO PULL OVER TO REMOVE THE LOOSE TRIM. DEALER WAS NOT NOTIFIED. *AK *TC
THE PISTON THAT HOLDS THE TRUCK LID OPEN OR UP FAILED. THE TRUNK ON THIS MODEL IS VERY HEAVY, SO IT DROPPED VERY FAST. MY WIFE WAS UNLOADING SOME LUGGAGE AND ONLY JUST WAS ABLE TO PULL HER ARM OUT AS THE LID FELL. HAD IT HIT HER, IT WOULD HAVE BROKEN HER ARM OR POSSIBLE SEVERED A HAND OR FINGERS.*AK
WHILE DRIVING AT 50 MPH PLASTIC MOLDING TRIM WHICH WAS MOUNTED ON THE HOOD FLEW OFF. AS A RESULT, THE MOLDING TRIM HIT THE WINDSHIELD AND CAUSED A CHIP ON DRIVER'S SIDE WINDOW. WHILE AT THE DEALERSHIP, WAS SENT TO SERVICE MANAGER AND THEN TO BODY SHOP. WAS INFORMED THAT MOLDING BROKE OFF DUE TO FATIGUE. *AK *NM
HOOD MOLDING BROKE FREE FROM IT'S MOUNTING CLASPS AT HIGHWAY SPEED AND FLEW OFF. IT HIT THE WINDSHIELD AND IF THERE WOULD HAVE BEEN A CAR BEHIND US THERE COULD OF BEEN AN ACCIDENT.
DRIVING DOWN THE HIGHWAY AT 65 MPH, COWL AND MOLDING BETWEEN THE HOOD AND WINDSHIELD BLEW OFF FOR NO APPARENT REASON. WARRANTY ON VEHICLE HAS EXPIRED DUE TO MILEAGE. *LA CONSUMER WAS SEEKING REIMBURSEMENT FOR THE REPLACEMENT PART FOR $128.80, WHICH WAS DENIED BY DAIMLERCHRYSLER. IN ADDITION, THE CONSUMER REQUESTED AN INV…
Read full complaint
DRIVING DOWN THE HIGHWAY AT 65 MPH, COWL AND MOLDING BETWEEN THE HOOD AND WINDSHIELD BLEW OFF FOR NO APPARENT REASON. WARRANTY ON VEHICLE HAS EXPIRED DUE TO MILEAGE. *LA CONSUMER WAS SEEKING REIMBURSEMENT FOR THE REPLACEMENT PART FOR $128.80, WHICH WAS DENIED BY DAIMLERCHRYSLER. IN ADDITION, THE CONSUMER REQUESTED AN INVESTIGATION BE OPENED TO SEE IF THEIR COMPLAINT WARRANTED A RECALL. *PH
CONSUMER NOTICED TWO SUDDEN CRACKS (SLITS) ALONG THE AIRBAG AREA. *PH THE DASHBOARD HAD TO BE REPLACED. *TT *JB
WHILE DRIVING DOWN THE HIGHWAY AT 65 MPH, THE COWL MOLDING BETWEEN THE HOOD AND WINDSHIELD BLEW OFF FOR NO APPARENT REASON. *PH *JB *NM
Official recalls
404V021000 · Power Train:automatic Transmission:lever And Linkage:floor Shift
Jan 13, 2004
ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.
Consequence & remedy
Consequence: EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.
Remedy: DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
03V035000 · Seats:front Assembly:recliner
Feb 5, 2003
ON CERTAIN PASSENGER VEHICLES, SEAT BACK RECLINER BOLT BREAKAGE CAN OCCUR RESULTING IN THE SEAT BACK RECLINING UNEXPECTEDLY.
Consequence & remedy
Consequence: IF THE SEAT BACK UNEXPECTEDLY RECLINES WHILE THE CAR IS BEING DRIVEN, IT COULD RESULT IN LOSS OF VEHICLE CONTROL, INCREASING THE RISK OF A CRASH.
Remedy: DEALERS WILL REPLACE THE RECLINER BOLTS. OWNER NOTIFICATION BEGAN ON APRIL 23, 2003. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
01V119000 · Seat Belts:front:retractor
Apr 11, 2001
VEHICLE DESCRIPTION: CERTAIN VAN, WAGON, PICKUP TRUCKS, PASSENGER AND SPORT UTILITY VEHICLES, FAIL TO COMPLY WITH REQUIREMENTS OF FMVSS NO. 209, "SEAT BELT ASSEMBLIES." THE FRONT SEAT BELT RETRACTOR MAY NOT COMPLY WITH THE REQUIREMENTS OF THE STANDARD.
Consequence & remedy
Consequence: IF THE RETRACTOR DOES NOT WORK PROPERLY, IT WILL NOT ADEQUATELY PROTECT OCCUPANTS IN THE EVENT OF A CRASH.
Remedy: DEALERS WILL REPLACE THE SEAT BELT RETRACTOR. OWNER NOTIFICATION BEGAN AUGUST 20, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
00V034000 · Seat Belts
Feb 4, 2000
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SEAT BELT SHOULDER HEIGHT ADJUSTABLE TURNING LOOP (ATL) TOP MOUNTING BOLT WAS INADEQUATELY MANUFACTURED.
Consequence & remedy
Consequence: THE AFFECTED MOUNTING BOLTS MAY NOT WITHSTAND SUFFICIENT FORCE TO FUNCTION PROPERLY IN CERTAIN IMPACT SITUATIONS, INCREASING THE RISK OF INJURY TO A BELTED OCCUPANT.
Remedy: DEALERS WILL REPLACE THE SHOULDER BELT HEIGHT ADJUSTER MOUNTING BOLTS.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA03011 · Auto Trans IGNITION-PARK Interlock
Opened Jul 17, 2003 · Closed Jan 30, 2004
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Additional source detail variants (2)
Power Train:automatic Transmission
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
PE03010 · Throttle Control Failure
Opened Feb 27, 2003 · Closed Sep 2, 2003
Status: closed (inferred from source dates) · Vehicle Speed Control; Vehicle Speed Control:accelerator Pedal; Vehicle Speed Control:cables; Vehicle Speed Control:linkages
BASED ON THE LOW FAILURE RATE, THE ABSENCE OF FAILURES OVER THE PAST YEAR, THE ABSENCE OF INJURIES, AND ODI'S FIELD INVESTIGATION OF INCIDENT VEHICLES, A SAFETY-RELATED DEFECT TREND HAS NOT BEEN IDENTIFIED AT THIS TIME.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES. SEE ATTACHED REPORT FOR ADDITIONAL INFORMATION.
Additional source detail variants (4)
Vehicle Speed Control:accelerator Pedal
BASED ON THE LOW FAILURE RATE, THE ABSENCE OF FAILURES OVER THE PAST YEAR, THE ABSENCE OF INJURIES, AND ODI'S FIELD INVESTIGATION OF INCIDENT VEHICLES, A SAFETY-RELATED DEFECT TREND HAS NOT BEEN IDENTIFIED AT THIS TIME.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES. SEE ATTACHED REPORT FOR ADDITIONAL INFORMATION.
Vehicle Speed Control:cables
BASED ON THE LOW FAILURE RATE, THE ABSENCE OF FAILURES OVER THE PAST YEAR, THE ABSENCE OF INJURIES, AND ODI'S FIELD INVESTIGATION OF INCIDENT VEHICLES, A SAFETY-RELATED DEFECT TREND HAS NOT BEEN IDENTIFIED AT THIS TIME.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES. SEE ATTACHED REPORT FOR ADDITIONAL INFORMATION.
Vehicle Speed Control
BASED ON THE LOW FAILURE RATE, THE ABSENCE OF FAILURES OVER THE PAST YEAR, THE ABSENCE OF INJURIES, AND ODI'S FIELD INVESTIGATION OF INCIDENT VEHICLES, A SAFETY-RELATED DEFECT TREND HAS NOT BEEN IDENTIFIED AT THIS TIME.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES. SEE ATTACHED REPORT FOR ADDITIONAL INFORMATION.
Vehicle Speed Control:linkages
BASED ON THE LOW FAILURE RATE, THE ABSENCE OF FAILURES OVER THE PAST YEAR, THE ABSENCE OF INJURIES, AND ODI'S FIELD INVESTIGATION OF INCIDENT VEHICLES, A SAFETY-RELATED DEFECT TREND HAS NOT BEEN IDENTIFIED AT THIS TIME.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY WILL TAKE FURTHER ACTION IF WARRANTED BY THE CIRCUMSTANCES. SEE ATTACHED REPORT FOR ADDITIONAL INFORMATION.