NHTSA owner reports · September 18, 2026 snapshot.
Steering complaints
30 reportsClear category filterMileage unknown · Apr 25, 2002
Electrical SystemSteeringSuspension
FRAME OF VEHICLE IS WEAK AND IS MOVING UNDER STEERING GEAR. CAUSE IS UNKNOWN. *AK CONSUMER STATES THAT HE REPLACED THE RACK AND PINION AND IN DOING SO, FOUND THAT THE WIRING HARNESS THAT GOES FROM THE SOLENOID CONTROL MODULE AND THE SOLENOID CONTROL VALVE HAD BEEN PUT IN BETWEEN THE CROSSMEMBER AND THE RACK AND PINION, A BOLT…
Read full complaint
FRAME OF VEHICLE IS WEAK AND IS MOVING UNDER STEERING GEAR. CAUSE IS UNKNOWN. *AK CONSUMER STATES THAT HE REPLACED THE RACK AND PINION AND IN DOING SO, FOUND THAT THE WIRING HARNESS THAT GOES FROM THE SOLENOID CONTROL MODULE AND THE SOLENOID CONTROL VALVE HAD BEEN PUT IN BETWEEN THE CROSSMEMBER AND THE RACK AND PINION, A BOLT HAD CUT AND SHORTED OUT THE HARNESS, THIS IS THE BOLT THAT HOLDS THE MOUNT OF THE RACK AND PINION, WHILE TURNING THE WHEEL TO THE LEFT AND RIGHT, THE MASTER CYLINDER AND RACK AND PINION MOVE, DEALER RECOMENDED REPLACEMENT OF THE RACK BUSHINGS AND RIGHT SWAY BAR LINK, HOWEVER STATED THE STEERING WAS NOT A PROBLEM. *SLC
NHTSA ODI #8008591
Mileage unknown · Sep 12, 2001
Steering
NO SUMMARY LISTED FOR ABOVE VEHICLE. *AK
NHTSA ODI #752109
Mileage unknown · Jun 19, 2001
Electrical SystemSteering
RIGHT STEERING TIE ROD HAS RUBBED THROUGH TRANSMISSION HARNESS, CAUSING A SHORT CIRCUIT WHICH RESULTED IN AN ELECTRICAL SYSTEM MALFUNCTION. A RECALL HAS BEEN ISSUED ON VEHICLE'S MAKE AND MODEL. HOWEVER, THIS VEHICLE WAS NOT INCLUDED DUE TO VIN. VEHICLE WAS REPAIRED AT THE OWNER'S EXPENSE. *AK
NHTSA ODI #890631
Mileage unknown · Dec 29, 2000
Engine And Engine CoolingService Brakes, HydraulicSteering
WHITE SMOKE COMES OUT OF ENGINE. BRAKES SELF APPLYED WHILE DRIVING. STEERING WOBBLES ALL ACROSS LANES.*AK
NHTSA ODI #738454
Mileage unknown · Sep 5, 2000
SteeringSuspension
VEHICLE WENT IN THE OPPOSITE OF THE DIRECTION FROM WHERE IT WASSUPPOSE TO GO. DEALER REPLACED INNER TIE ROD & WHEEL ALIGNMENT. OTHER TIE ROD WILL NEED TO BE DONE. *AK
NHTSA ODI #869560
Mileage unknown · Jul 18, 2000
Steering
WHILE DRIVING AT APPROXIMATELY 40MPH TIE ROD BROKE, CAUSING A LACK OF STEERING & NO CONTROL OF VEHICLE. THIS HAS HAPPENED ONCE BEFORE. VEHICLE TOWED TO DEALER. RACK & PINION NEEDED REPLACING. CONTACTED MANUFACTURER.*AK
NHTSA ODI #865629
Mileage unknown · Jun 21, 2000
EquipmentPower TrainSteering
THIS CAR HAD A BUMPER TO BUMPER 60,000 MILE WARRANTY - TRANSMISSION AND AIR CONDITIONING SHOULD HAVE BEEN COVERED 100% I DID NOT PURCHASE THIS VEHICLE FROM VANDYNHOVEN'S ONLY HAD IT SERVICED THROUGH THEM. THEY ARE REIMBURSING ME 50% ON THE AIRCONDITIONING BECAUSE CHRYSLER HAS AGREED TO PAY 50% BUT I FEEL THAT THE EVAPORATOR COR…
Read full complaint
THIS CAR HAD A BUMPER TO BUMPER 60,000 MILE WARRANTY - TRANSMISSION AND AIR CONDITIONING SHOULD HAVE BEEN COVERED 100% I DID NOT PURCHASE THIS VEHICLE FROM VANDYNHOVEN'S ONLY HAD IT SERVICED THROUGH THEM. THEY ARE REIMBURSING ME 50% ON THE AIRCONDITIONING BECAUSE CHRYSLER HAS AGREED TO PAY 50% BUT I FEEL THAT THE EVAPORATOR CORE WAS WARRANTEED UP TO 70,000 MILES AND NOW I'M AT 71,700 AND THEY AREN'T COVERING IT IN FULL. THE CAR WAS BROUGHT IN AT LEAST 2 TIMES WHILE UNDER WARRANTY WITH AIR PROBLEMS ? SAME WITH THE TRANSMISSION - IT WAS BROUGHT IN ON SEVERAL OCCATIONS WHERE IT SHOULD HAVE BEEN FULLY COVERED AND I HAD TO PAY $750.00 THE INTAKE MANIFOLD WAS LEAKING ON 10/04/99 *AK
NHTSA ODI #724327
Mileage unknown · Jun 12, 2000
Steering
RACK & PINION STEERING WENT OUT. ALSO, LEFT INNER TIE ROD BROKE. *AK
NHTSA ODI #863440
Mileage unknown · May 5, 2000
Steering
TWO AND ONLY BOLTS OF RACK AND PINION COMPLETELY SHEARED OFF EXITING FROM GAS STATION RESULTING IN TOTAL LOSS OF STEERING. ORIGINAL RACK AND PINION WAS REPLACED AT 47K MILES WITH A NEW ONE. DEALER BEING VERY COOPERATIVE IN TRYING TO GET REIMBURSEMENT FOR US ($800+). OUR CONCERN IS POSSIBLY DEFECTIVE BOLTS AND NEED TO ISSUE RE…
Read full complaint
TWO AND ONLY BOLTS OF RACK AND PINION COMPLETELY SHEARED OFF EXITING FROM GAS STATION RESULTING IN TOTAL LOSS OF STEERING. ORIGINAL RACK AND PINION WAS REPLACED AT 47K MILES WITH A NEW ONE. DEALER BEING VERY COOPERATIVE IN TRYING TO GET REIMBURSEMENT FOR US ($800+). OUR CONCERN IS POSSIBLY DEFECTIVE BOLTS AND NEED TO ISSUE RECALL FOR REPLACEMENT OF BOLTS. WE KEPT ORIGINAL SHEARED BOLTS AND RACK. DEALER NOW HAS BOLTS AND HAS SENT THEM TO DETROIT FOR TESTING. DEALER ALSO HAS NOW TAKEN POSSESION OF RACK AND PINION SHOWING REMNANTS OF SHEARED BOLTS INSIDE. WE HAVE HAD MANY PROBLEMS WITH THE FRONT END/STEERING OF THIS VEHICLE. EACH TIME REPAIR IS MADE, PROBLEM GETS WORSE, NOW CULMINATING IN TOTAL LOSS OF STEERING WHICH COULD HAVE ALSO RESULTED IN THE DEATH OF MY WIFE, WHO WAS DRIVING THE CAR. FORTUNATELY, SHE HAD PULLED INTO A GAS STATION AFTER DRIVING SEVERAL HOURS ON I-74 AT 65 MPH. SHOULD A 1994 CHRYSLER LHS NOW BE ON ITS THIRD RACK AND PINION. I THINK NOT. I'M NOT OPTIMISTIC DEALER WILL COME BACK WITH A DEFINITIVE ANSWER ALTHOUGH THE BOLTS WERE SENT TO CHRYSLER ENGINEERING FOR METALURGY TESTING. IF YOU NEED FURTHER INFORMATION, WE HAVE DOCUMENTED ALL REPAIRS/PROBLEMS WITH THIS VEHICLE AND WOULD SUPPLY YOU WITH SAME. *AK
NHTSA ODI #722325
Mileage unknown · Apr 28, 2000
Steering
RACK AND PINION STEERING WELDS ARE BREAKING AWAY FROM THE K-FRAME. DEALER HAS BEEN CONTACTED. *AK
NHTSA ODI #861101
NHTSA investigations
10DP04007 · Fuel Rail, Brake Fluid, Chassis
Opened Oct 13, 2004 · Closed Oct 27, 2004
Status: closed (inferred from source dates) · Fuel System, Gasoline:fuel Injection System:fuel Rail; Service Brakes, Hydraulic:fluid; Structure:frame And Members
ON SEPTEMBER 5, 2004, MR. ROBERT GALENTY OF ISELIN, NJ, PETITIONED THE AGENCY TO CONDUCT DEFECT INVESTIGATIONS OF CERTAIN MODEL YEAR (MY) 1993-1997 VEHICLES PRODUCED BY DAIMLERCHRYSLER CORPORATION.HIS PETITION IDENTIFIED THREE ISSUES OF CONCERN: 1) FUEL LEAKING FROM THE FUEL INJECTOR RAILS; 2) BRAKE FLUID CONTAMINATION RESULTING IN BRAKE FAILURE; AND 3) SUSCEPTIBILITY OF THE VEHICLE FRAME TO DAMAGE WHILE THE VEHICLE IS BEING TOWED.MR. GALANTY ALLEGED THAT HIS 1996 DODGE INTREPID HAD EACH OF THESE THREE PROBLEMS.CONCERNING FUEL RAIL LEAKAGE, DAIMLERCHRYSLER COMMENCED A RECALL (98V-184) OF APPROXIMATELY 722,600 VEHICLES TO ADDRESS ENGINE FUEL RAIL LEAKS THAT COULD LEAD TO A FIRE, INCLUDING THOSE VEHICLES CITED IN THE PETITION AND THE PETITIONER'S 1996 DODGE INTREPID.ON OCTOBER 7, 1998, NHTSA OPENED A RECALL QUERY INVESTIGATION (RQ98-018) TO EVALUATE THE ADEQUACY OF THE RECALL REMEDY.THAT INVESTIGATION WAS CLOSED ON JULY 8, 2002 WITHOUT REQUIRING FURTHER ACTION BY DAIMLERCHRYSLER.VERY RECENTLY, ON JUNE 9, 2004, NHTSA DENIED A PETITION (RP04-001) TO REOPEN RQ98-018 AFTER FINDING THAT THERE WAS NO NEW INFORMATION THAT WOULD INDICATE ANY BASIS FOR REOPENING IT.THIS IS STILL THE CURRENT POSITION OF NHTSA ON THIS ISSUE.CONCERNING BRAKE FLUID CONTAMINATION AND FRAME ALIGNMENT, A REVIEW OF NHTSA'S DATABASE SHOWS NO OTHER COMPLAINTS ON EITHER ONE OF THESE ISSUES ON THE VEHICLES CITED IN THE PETITION.
Additional source detail variants (3)
Fuel System, Gasoline:fuel Injection System:fuel Rail
ON SEPTEMBER 5, 2004, MR. ROBERT GALENTY OF ISELIN, NJ, PETITIONED THE AGENCY TO CONDUCT DEFECT INVESTIGATIONS OF CERTAIN MODEL YEAR (MY) 1993-1997 VEHICLES PRODUCED BY DAIMLERCHRYSLER CORPORATION.HIS PETITION IDENTIFIED THREE ISSUES OF CONCERN: 1) FUEL LEAKING FROM THE FUEL INJECTOR RAILS; 2) BRAKE FLUID CONTAMINATION RESULTING IN BRAKE FAILURE; AND 3) SUSCEPTIBILITY OF THE VEHICLE FRAME TO DAMAGE WHILE THE VEHICLE IS BEING TOWED.MR. GALANTY ALLEGED THAT HIS 1996 DODGE INTREPID HAD EACH OF THESE THREE PROBLEMS.CONCERNING FUEL RAIL LEAKAGE, DAIMLERCHRYSLER COMMENCED A RECALL (98V-184) OF APPROXIMATELY 722,600 VEHICLES TO ADDRESS ENGINE FUEL RAIL LEAKS THAT COULD LEAD TO A FIRE, INCLUDING THOSE VEHICLES CITED IN THE PETITION AND THE PETITIONER'S 1996 DODGE INTREPID.ON OCTOBER 7, 1998, NHTSA OPENED A RECALL QUERY INVESTIGATION (RQ98-018) TO EVALUATE THE ADEQUACY OF THE RECALL REMEDY.THAT INVESTIGATION WAS CLOSED ON JULY 8, 2002 WITHOUT REQUIRING FURTHER ACTION BY DAIMLERCHRYSLER.VERY RECENTLY, ON JUNE 9, 2004, NHTSA DENIED A PETITION (RP04-001) TO REOPEN RQ98-018 AFTER FINDING THAT THERE WAS NO NEW INFORMATION THAT WOULD INDICATE ANY BASIS FOR REOPENING IT.THIS IS STILL THE CURRENT POSITION OF NHTSA ON THIS ISSUE.CONCERNING BRAKE FLUID CONTAMINATION AND FRAME ALIGNMENT, A REVIEW OF NHTSA'S DATABASE SHOWS NO OTHER COMPLAINTS ON EITHER ONE OF THESE ISSUES ON THE VEHICLES CITED IN THE PETITION.
Service Brakes, Hydraulic:fluid
ON SEPTEMBER 5, 2004, MR. ROBERT GALENTY OF ISELIN, NJ, PETITIONED THE AGENCY TO CONDUCT DEFECT INVESTIGATIONS OF CERTAIN MODEL YEAR (MY) 1993-1997 VEHICLES PRODUCED BY DAIMLERCHRYSLER CORPORATION.HIS PETITION IDENTIFIED THREE ISSUES OF CONCERN: 1) FUEL LEAKING FROM THE FUEL INJECTOR RAILS; 2) BRAKE FLUID CONTAMINATION RESULTING IN BRAKE FAILURE; AND 3) SUSCEPTIBILITY OF THE VEHICLE FRAME TO DAMAGE WHILE THE VEHICLE IS BEING TOWED.MR. GALANTY ALLEGED THAT HIS 1996 DODGE INTREPID HAD EACH OF THESE THREE PROBLEMS.CONCERNING FUEL RAIL LEAKAGE, DAIMLERCHRYSLER COMMENCED A RECALL (98V-184) OF APPROXIMATELY 722,600 VEHICLES TO ADDRESS ENGINE FUEL RAIL LEAKS THAT COULD LEAD TO A FIRE, INCLUDING THOSE VEHICLES CITED IN THE PETITION AND THE PETITIONER'S 1996 DODGE INTREPID.ON OCTOBER 7, 1998, NHTSA OPENED A RECALL QUERY INVESTIGATION (RQ98-018) TO EVALUATE THE ADEQUACY OF THE RECALL REMEDY.THAT INVESTIGATION WAS CLOSED ON JULY 8, 2002 WITHOUT REQUIRING FURTHER ACTION BY DAIMLERCHRYSLER.VERY RECENTLY, ON JUNE 9, 2004, NHTSA DENIED A PETITION (RP04-001) TO REOPEN RQ98-018 AFTER FINDING THAT THERE WAS NO NEW INFORMATION THAT WOULD INDICATE ANY BASIS FOR REOPENING IT.THIS IS STILL THE CURRENT POSITION OF NHTSA ON THIS ISSUE.CONCERNING BRAKE FLUID CONTAMINATION AND FRAME ALIGNMENT, A REVIEW OF NHTSA'S DATABASE SHOWS NO OTHER COMPLAINTS ON EITHER ONE OF THESE ISSUES ON THE VEHICLES CITED IN THE PETITION.
Structure:frame And Members
ON SEPTEMBER 5, 2004, MR. ROBERT GALENTY OF ISELIN, NJ, PETITIONED THE AGENCY TO CONDUCT DEFECT INVESTIGATIONS OF CERTAIN MODEL YEAR (MY) 1993-1997 VEHICLES PRODUCED BY DAIMLERCHRYSLER CORPORATION.HIS PETITION IDENTIFIED THREE ISSUES OF CONCERN: 1) FUEL LEAKING FROM THE FUEL INJECTOR RAILS; 2) BRAKE FLUID CONTAMINATION RESULTING IN BRAKE FAILURE; AND 3) SUSCEPTIBILITY OF THE VEHICLE FRAME TO DAMAGE WHILE THE VEHICLE IS BEING TOWED.MR. GALANTY ALLEGED THAT HIS 1996 DODGE INTREPID HAD EACH OF THESE THREE PROBLEMS.CONCERNING FUEL RAIL LEAKAGE, DAIMLERCHRYSLER COMMENCED A RECALL (98V-184) OF APPROXIMATELY 722,600 VEHICLES TO ADDRESS ENGINE FUEL RAIL LEAKS THAT COULD LEAD TO A FIRE, INCLUDING THOSE VEHICLES CITED IN THE PETITION AND THE PETITIONER'S 1996 DODGE INTREPID.ON OCTOBER 7, 1998, NHTSA OPENED A RECALL QUERY INVESTIGATION (RQ98-018) TO EVALUATE THE ADEQUACY OF THE RECALL REMEDY.THAT INVESTIGATION WAS CLOSED ON JULY 8, 2002 WITHOUT REQUIRING FURTHER ACTION BY DAIMLERCHRYSLER.VERY RECENTLY, ON JUNE 9, 2004, NHTSA DENIED A PETITION (RP04-001) TO REOPEN RQ98-018 AFTER FINDING THAT THERE WAS NO NEW INFORMATION THAT WOULD INDICATE ANY BASIS FOR REOPENING IT.THIS IS STILL THE CURRENT POSITION OF NHTSA ON THIS ISSUE.CONCERNING BRAKE FLUID CONTAMINATION AND FRAME ALIGNMENT, A REVIEW OF NHTSA'S DATABASE SHOWS NO OTHER COMPLAINTS ON EITHER ONE OF THESE ISSUES ON THE VEHICLES CITED IN THE PETITION.
EA03011 · Auto Trans IGNITION-PARK Interlock
Opened Jul 17, 2003 · Closed Jan 30, 2004
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Additional source detail variants (2)
Power Train:automatic Transmission
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
DP03002 · Steering Column Separation
Opened May 7, 2003 · Closed Jul 22, 2003
Status: closed (inferred from source dates) · Steering:column
MR. LARRY A. SACKEY SUBMITTED A PETITION TO THE NATIONAL HIGHWAY TRAFFIC SAFETY ADMINISTRATION (NHTSA) BY LETTER DATED APRIL 18, 2003, REQUESTING THAT NHTSAFURTHER INVESTIGATE THE DEFECTIVE COLLAPSIBLE STEERING SHAFT SYSTEM ON 1987-1995 VEHICLES MANUFACTURED BY THE DAIMLERCHRYSLER CORPORATION.IN PART BECAUSE OF 49 CFR ? 30120(G), NHTSA HAS DECIDED TO LIMIT THE SCOPE OF THE PETITION VEHICLES TO 1993-1995 MODELS, EXCLUDING THE 1993 JEEP GRAND CHEROKEE AND 1994-1995 DODGE RAM SERIES TRUCKS THAT WERE RECALLED (93V210 & 96V230) FOR STEERING COLUMN FAILURE.IF THE ANALYSIS OF THESE VEHICLES HAD IDENTIFIED A POTENTIAL PROBLEM, THE SCOPE COULD HAVE BEEN EXPANDED IN AN INVESTIGATION.A REVIEW OF ODI'S DATA BASE SHOWS NO RECENT COMPLAINTS AND A LACK OF A COMPLAINT TREND CONCERNING THE SUBJECT ISSUE ON THE SUBJECT VEHICLES AS A WHOLE OR BY INDIVIDUAL MODELS.THEREFORE, THE PETITION IS DENIED.FOR DETAILS, SEE FEDERAL REGISTER NOTICE VOLUME 68, NO. 130, JULY 8, 2003.
EA99031 · Steering System Rack And Pinion
Opened Oct 29, 1999 · Closed Sep 13, 2001
Status: closed (inferred from source dates) · Steering
There is no summary currently available
PE99044 · Steering System Rack And Pinion
Opened Jun 28, 1999 · Closed Oct 29, 1999
Status: closed (inferred from source dates) · Steering
SINCE OPENING THE PRELIMINARY EVALUATION (PE), ODI HAS RECEIVED 6 ADDITIONAL COMPLAINTS.DURING THE PE IT WAS DETERMINED MULTIPLE FAILURE MODES ARE INVOLVED IN THIS MATTER.THE WARRANTY CLAIM RATE IS HIGH FOR A STEERING SYSTEM CONCERN.THE ISSUES REPORTED INVOLVE PREMATURE WEAR OUT AT THE RACK AND PINION INTERFACE WITH THE INNER TIE ROD END(S), BINDING AND STICKING OF THE STEERING GEAR, CRACKED OR BROKEN TIE ROD ENDS, SHEARED RACK AND PINION ASSEMBLY BOLTS, AND WEAR OUT OF THE RACK AND PINION MOUNT BUSHINGS.MANY OF THE COMPLAINANTS MENTION STEERING WONDER AND LOOSE STEERING.THREE OF THE MOST RECENT COMPLAINTS ALLEGE A COMPLETE LOSS OF STEERING DUE TO SHEARED BOLTS.ODI IS UPGRADING THIS PE IN ORDER TO PERFORM A THOROUGH TECHNICAL ANALYSIS OF THE VARIOUS SYSTEM FAILURE ALLEGATIONS AND TO QUANTIFY THE EFFECT THAT THESE FAILURES HAVE ON VEHICLE CONTROL.
EA98025 · Engine Cradle/control Arm Bracket Weld
Opened Dec 31, 1998 · Closed Aug 19, 1999
Status: closed (inferred from source dates) · Suspension
There is no summary currently available
RQ98018 · Fuel Injection Delivery System Fuel Leak
Opened Oct 7, 1998 · Closed Jul 8, 2002
Status: closed (inferred from source dates) · Fuel System, Gasoline:fuel Injection System
No summary supplied.
PE98044 · Engine Cradle/control Arm Bracket Weld
Opened Aug 11, 1998 · Closed Dec 31, 1998
Status: closed (inferred from source dates) · Suspension
ALLEGED THAT THE FRONT SUSPENSION WELD FAILS OR CRACKS CAUSING THE SUSPENSION TO COLLAPSE AND A LOSS OF VEHICLE CONTROL
EA98007 · Fuel Injector Assembly Leakage
Opened Mar 10, 1998 · Closed Feb 1, 1999
Status: closed (inferred from source dates) · Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings; Fuel System, Gasoline:fuel Injection System; Fuel System, Gasoline:fuel Injection System:fuel Rail
NITRILE RUBBER SEALS USED IN THE FUEL RAIL ASSEMBLIES OF THE SUBJECT VEHICLES AT THE SUPPLY, RETURN, AND CROSSOVER TUBE FITTINGS, AND AT THE PRESSURE REGULATOR FAIL, RESULTING IN FUEL LEAKAGE IN THE ENGINE COMPARTMENT.ALSO, THE OUTLET (RIGHT) FUEL RAIL MAY LEAK FROM CRACKS AT CERTAIN MOLD GATES IN THE THERMOSET RAIL MATERIAL.CHRYSLER WILL RECALL THE SUBJECT VEHICLES AND STATED THAT IT INTENDS TO REPLACE THE O-RINGS WITH FLUOROCARBON O-RING HAVING GREATER HEAT RESISTANCE CAPABILITY AND ATTACH REINFORCEMENTS TO THE RAIL IN THE AREAS WHERE THE CRACKING CONCERN HAS BEEN KNOWN TO OCCUR MOST FREQUENTLY.RAILS THAT ARE ALREADY CRACKED WILL BE REPLACED BY NEW, REINFORCED RAILS.
Additional source detail variants (3)
Fuel System, Gasoline:delivery:hoses, Lines/piping, And Fittings
NITRILE RUBBER SEALS USED IN THE FUEL RAIL ASSEMBLIES OF THE SUBJECT VEHICLES AT THE SUPPLY, RETURN, AND CROSSOVER TUBE FITTINGS, AND AT THE PRESSURE REGULATOR FAIL, RESULTING IN FUEL LEAKAGE IN THE ENGINE COMPARTMENT.ALSO, THE OUTLET (RIGHT) FUEL RAIL MAY LEAK FROM CRACKS AT CERTAIN MOLD GATES IN THE THERMOSET RAIL MATERIAL.CHRYSLER WILL RECALL THE SUBJECT VEHICLES AND STATED THAT IT INTENDS TO REPLACE THE O-RINGS WITH FLUOROCARBON O-RING HAVING GREATER HEAT RESISTANCE CAPABILITY AND ATTACH REINFORCEMENTS TO THE RAIL IN THE AREAS WHERE THE CRACKING CONCERN HAS BEEN KNOWN TO OCCUR MOST FREQUENTLY.RAILS THAT ARE ALREADY CRACKED WILL BE REPLACED BY NEW, REINFORCED RAILS.
Fuel System, Gasoline:fuel Injection System
NITRILE RUBBER SEALS USED IN THE FUEL RAIL ASSEMBLIES OF THE SUBJECT VEHICLES AT THE SUPPLY, RETURN, AND CROSSOVER TUBE FITTINGS, AND AT THE PRESSURE REGULATOR FAIL, RESULTING IN FUEL LEAKAGE IN THE ENGINE COMPARTMENT.ALSO, THE OUTLET (RIGHT) FUEL RAIL MAY LEAK FROM CRACKS AT CERTAIN MOLD GATES IN THE THERMOSET RAIL MATERIAL.CHRYSLER WILL RECALL THE SUBJECT VEHICLES AND STATED THAT IT INTENDS TO REPLACE THE O-RINGS WITH FLUOROCARBON O-RING HAVING GREATER HEAT RESISTANCE CAPABILITY AND ATTACH REINFORCEMENTS TO THE RAIL IN THE AREAS WHERE THE CRACKING CONCERN HAS BEEN KNOWN TO OCCUR MOST FREQUENTLY.RAILS THAT ARE ALREADY CRACKED WILL BE REPLACED BY NEW, REINFORCED RAILS.
Fuel System, Gasoline:fuel Injection System:fuel Rail
NITRILE RUBBER SEALS USED IN THE FUEL RAIL ASSEMBLIES OF THE SUBJECT VEHICLES AT THE SUPPLY, RETURN, AND CROSSOVER TUBE FITTINGS, AND AT THE PRESSURE REGULATOR FAIL, RESULTING IN FUEL LEAKAGE IN THE ENGINE COMPARTMENT.ALSO, THE OUTLET (RIGHT) FUEL RAIL MAY LEAK FROM CRACKS AT CERTAIN MOLD GATES IN THE THERMOSET RAIL MATERIAL.CHRYSLER WILL RECALL THE SUBJECT VEHICLES AND STATED THAT IT INTENDS TO REPLACE THE O-RINGS WITH FLUOROCARBON O-RING HAVING GREATER HEAT RESISTANCE CAPABILITY AND ATTACH REINFORCEMENTS TO THE RAIL IN THE AREAS WHERE THE CRACKING CONCERN HAS BEEN KNOWN TO OCCUR MOST FREQUENTLY.RAILS THAT ARE ALREADY CRACKED WILL BE REPLACED BY NEW, REINFORCED RAILS.
EA95028 · Underhood Fuel Leaks
Opened Sep 22, 1995 · Closed Feb 24, 1997
Status: closed (inferred from source dates) · Vehicle Speed Control:linkages
A SAFETY-RELATED DEFECT TREND HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.THE CLOSING OF THIS INVESTIGATION DOES NOT CONSTITUTE A FINDING BY NHTSA THAT NO SAFETY-RELATED DEFECT EXISTS.THE AGENCY RESERVES THE RIGHT TO TAKE FURTHER ACTION IF WAARRANTED BY THE CIRCUMSTANCES.AN ENGINEERING ANALYSIS CLOSSING REPORT IS INCLUDED IN THE PUBLIC FILE.
Illustration