IllustrationWHILE TRAVELING ON THE HIGHWAY AND WITHOUT PRIOR WARNING THERE WAS A EXPLOSION DUE TO THE TRANS AXLE LOOSENING AND BUSTING THE TRANSMISSION CASE. *AK THE VEHICLE EXPERIENCED LOSS OF POWER STEERING AND BRAKES. THE TRANSMISSION WAS SERVICED. *PH *JB *JB *PH *JB
1996 Chrysler Cirrus
Owner reports · Recalls · Investigations
More warning signs than most Cirrus years
Owner complaints for the 1996 Chrysler Cirrus are substantially higher than the model-year median of 69.
About this comparison →How this year compares
Owner complaints by model year
Compare all Cirrus years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 22 of 160 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine And Engine Cooling. Review the 38 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes, Hydraulic. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
10 crash reports5 fire reports8 injury reports
What owners actually said
160 reportsPASSENGER SIDE REAR WHEEL "KNUCKLE" BROKE OFF WHERE SUPPORT ARM TO VEHICLE ATTACHES. THIS CAUSES REAR WHEEL ASSEMBLY TO LOOSE STRUCTURAL SUPPORT. REAR WHEEL IS THEN FREE TO TWIST IN ALL DIRECTIONS CAUSING LOSS OF CONTROL OF THE VEHICLE. AT HIGHWAY SPEEDS THIS CAN CAUSE A CATASTROPHIC ACCIDENT. THE "KNUCKLE" IS CAST ALUMINUM …
Read full complaint
PASSENGER SIDE REAR WHEEL "KNUCKLE" BROKE OFF WHERE SUPPORT ARM TO VEHICLE ATTACHES. THIS CAUSES REAR WHEEL ASSEMBLY TO LOOSE STRUCTURAL SUPPORT. REAR WHEEL IS THEN FREE TO TWIST IN ALL DIRECTIONS CAUSING LOSS OF CONTROL OF THE VEHICLE. AT HIGHWAY SPEEDS THIS CAN CAUSE A CATASTROPHIC ACCIDENT. THE "KNUCKLE" IS CAST ALUMINUM AND HAS NO MOVING PARTS WHICH CAN WEAR OUT.*AK
WHILE DRIVING THE DRIVERS SEAT BACK COLLAPSED. *NLM
CONSUMER STATES THAT DRIVER SIDE DOOR CAUGHT ON FIRE, DEALER NOTIFIED SAID WIRING NEAR CONTROLS WAS THE CAUSE. TS
THE REAR BRAKE HOSE COLLAPSED FROM EXCESSIVE HARDWARE DUST, WHICH CAUSED THE REAR WHEEL CYLINDER TO LEAK, THE REAR BRAKES WERE REPLACED, THE MASTER CYLINDER WAS REPLACED UNDER RECALL, HOWEVER IT HAD TO BE REPLACED A SECOND TIME. TS *JB
WHEN CONSUMER APPLIED THE BRAKES SUDDENLY TO AVOID A COLLISION, THE BRAKES LOCKED UP WHICH CAUSED VEHICLE TO SKID. VEHICLE HAD BEEN CHECKED BY 2 DEALERS AND AN INDEPENDENT MECHANIC WHO HAVE ALL CONFIRMED THE HYDRAULIC CONTROL UNIT HAD FAILED. TS *JB
WHILE DRIVING, UPON APPLYING BRAKES TO MAKE A GRADUAL STOP THE BRAKES FAILED TO RESPOND. VEHICLE WOULD NEED AN EXTENDED STOPPING DISTANCE. VEHICLE WAS INVOLVED IN A CRASH. CONSUMER HAS CONTACTED THE DEALER WHICH DETERMINED THAT THE FRONT BRAKE ROTORS WERE THE INCORRECT SIZE CAUSING THE PROBLEM. FRONT BRAKE ROTORS WERE REPLACE…
Read full complaint
WHILE DRIVING, UPON APPLYING BRAKES TO MAKE A GRADUAL STOP THE BRAKES FAILED TO RESPOND. VEHICLE WOULD NEED AN EXTENDED STOPPING DISTANCE. VEHICLE WAS INVOLVED IN A CRASH. CONSUMER HAS CONTACTED THE DEALER WHICH DETERMINED THAT THE FRONT BRAKE ROTORS WERE THE INCORRECT SIZE CAUSING THE PROBLEM. FRONT BRAKE ROTORS WERE REPLACED. TS
CONSUMER STATES THAT HEAD GASKET BLEW, AS A RESULT OF THE OIL FROM THE ENGINE GOING INTO THE RADIATOR. *MR
CONSUMER STATES VEHICLE OVERHEATED. THE ENGINE OIL GALLEY PLUG DOES NOT FIT PROPERLY. PLEASE PROVIDE FURTHER INFORMATION. 8MR
THE DRIVERS SIDE TIE ROD COMPLETELY SEPARATED FROM THE WHEEL AS THE CAR WAS BEING BACKED DOWN A DRIVEWAY. THIS MADE THE CAR IMMEDIATELY UNCONTROLLABLE. FORTUNATELY THIS HAPPENED AT VERY LOW SPEED IN THE DRIVE. MY WIFE WAS DRIVING THE CAR AND SHE HAD OUR 3 YEAR OLD SON IN THE CAR. IF THIS WOULD HAVE HAPPENED AT HIGH SPEED A T…
Read full complaint
THE DRIVERS SIDE TIE ROD COMPLETELY SEPARATED FROM THE WHEEL AS THE CAR WAS BEING BACKED DOWN A DRIVEWAY. THIS MADE THE CAR IMMEDIATELY UNCONTROLLABLE. FORTUNATELY THIS HAPPENED AT VERY LOW SPEED IN THE DRIVE. MY WIFE WAS DRIVING THE CAR AND SHE HAD OUR 3 YEAR OLD SON IN THE CAR. IF THIS WOULD HAVE HAPPENED AT HIGH SPEED A TERRIBLE ACCIDENT COULD HAVE OCCURRED. THE SHOP THAT FIXED THE TIE ROD SAID THAT THEY HAVE HAD MANY OF THE CIRRUS' WITH THIS FAILURE. THE JOINT ON THE TIE ROD INSTALLED BY THE MANUFACTURE WAS A SEALED TYPE AND HAD DRIED OUT AND RUSTED AWAY.*AK
Official recalls
704V021000 · Power Train:automatic Transmission:lever And Linkage:floor Shift
Jan 13, 2004
ON CERTAIN PASSENGER VEHICLES, THE FLOOR SHIFTER IGNITION-PARK INTERLOCK MAY FAIL AND ALLOW THE SHIFTER TO BE MOVED OUT OF THE PARK POSITION WITH THE KEY REMOVED. AN INOPERATIVE INTERLOCK MAY ALSO ALLOW THE KEY TO BE REMOVED WHEN THE SHIFTER HAS NOT BEEN PLACED IN THE PARK POSITION.
Consequence & remedy
Consequence: EITHER CIRCUMSTANCE MAY RESULT IN THE VEHICLE ROLLING AWAY WITHOUT WARNING.
Remedy: DEALERS WILL INSTALL A NEW LOAD-LIMITING PUSH ROD INTO THE FLOOR SHIFTER LEVER OF THE AFFECTED VEHICLES. OWNER NOTIFICATION BEGAN ON JUNE 14, 2004. OWNERS SHOULD CONTACT DAIMLERCHRYSLER AT 1-800-853-1403.
98V183000 · Power Train:automatic Transmission:park/neutral Start Interlock Switch
Aug 6, 1998
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH AUTOMATIC TRANSMISSIONS. THE ADJUSTMENT OF THE CABLE CONNECTING THE CONSOLE SHIFTER MECHANISM TO THE IGNITION KEY CAN CAUSE A TRAPPED KEY CONDITION WHICH CAN RESULT IN A LOW FORCE REQUIRED TO DEPRESS THE SHIFT BUTTON. A COMBINATION OF APPLYING A MIS-ADJUSTED RELEASE BUTTON WITH A LOW FORCE ATTEMPT TO SHIFT OUT OF PARK WITH THE KEY IN THE LOCKED POSITION, CAN BREAK THE CONNECTING PIN IN THE SHIFTER.
Consequence & remedy
Consequence: IF THIS HAPPENS, THE "IGNITION-PARK" INTERLOCK SYSTEM WILL BE NONFUNCTIONAL.
Remedy: DEALERS WILL INSPECT FOR PROPER OPERATION OF THE SYSTEM. ANY VEHICLES THAT ARE NOT FUNCTIONAL AFTER THE INSPECTION WILL HAVE THE SHIFT MECHANISM AND CABLE REPLACED WITH A "SELF-ADJUSTING" DESIGN.
97V201000 · Suspension:front:control Arm:lower Ball Joint
Nov 13, 1997
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE LOWER CONTROL ARM BALL JOINT CAN SEPARATE DUE TO LOSS OF LUBRICATION.
Consequence & remedy
Consequence: SEPARATION OF THE BALL JOINT COULD CAUSE A LOSS OF STEERING CONTROL INCREASING THE RISK OF A VEHICLE CRASH.
Remedy: DEALERS WILL INSPECT THE BALL JOINT END HOUSING COVER SEAL FOR LEAKAGE WITH A HIGH PRESSURE AIR TESTER AND THE RUBBER BOOT WILL BE VISUALLY INSPECTED FOR DAMAGE. IF THE COVER SEAL LEAKS OR THE BOOT IS DAMAGED, THE LOWER CONTROL ARM WILL BE REPLACED.
97V095000 · Structure:body:hood:hinge And Attachments
Jun 6, 1997
VEHICLE DESCRIPTION: PASSENGER VEHICLES. THE SECONDARY HOOD LATCH SPRING CAN DISENGAGE FROM ITS RETENTION HOLE IF THE HOOD IS SLAMMED SHUT.
Consequence & remedy
Consequence: IF THIS CONDITION OCCURS SIMULTANEOUSLY WITHOUT ENGAGING THE PRIMARY LATCH, THE HOOD WOULD NOT BE RESTRAINED INCREASING THE RISK OF A VEHICLE CRASH.
Remedy: DEALERS WILL REPLACE THE SECONDARY HOOD LATCH SPRING WITH A LONGER END HOOK SPRING.
96V075000 · Service Brakes, Hydraulic:foundation Components:master Cylinder
May 3, 1996
THE BRAKE MASTER CYLINDER CAN LEAK BRAKE FLUID DUE TO A DAMAGED DOUBLE LIP REAR PISTON SEAL.
Consequence & remedy
Consequence: BRAKE FLUID LEAKAGE CAN RESULT IN DIMINISHED EFFECTIVENESS OF ONE HALF OF THE SPLIT BRAKE SYSTEM. THE INSTRUMENT PANEL WARNING LIGHT(S) WILL SIGNAL SYSTEM IMPAIRMENT PRIOR TO PARTIAL BRAKE SYSTEM LOSS.
Remedy: DEALERS WILL REPLACE THE REAR BRAKE MASTER CYLINDR PISTON ASSEMBLY.
96V074000 · Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip
May 2, 1996
CORROSION OF THE ABS HYDRAULIC CONTROL UNIT CAN CAUSE THE SOLENOID VALVES TO STICK IN THE OPEN POSITION.
Consequence & remedy
Consequence: IF EITHER FRONT WHEEL VALVE STICKS, THE VEHICLE WOULD SWERVE FROM A STRAIGHT STOP WHEN THE BRAKES ARE APPLIED.
Remedy: DEALERS WILL INSTALL A PLATE AND SILICONE GREASE INJECTED INTO THE SOLENOID CAVITY TO ELIMINATE THE POTENTIAL FOR THIS CONDITION.
96V006000 · Engine And Engine Cooling:engine:gasoline
Jan 11, 1996
IN CERTAIN VEHICLES, THE ENGINE CYLINDER HEAD OIL GALLEY PLUG DOES NOT SEAL PROPERLY AND ENGINE CYLINDER HEAD OIL IS NOT ADEQUATELY RETAINED.
Consequence & remedy
Consequence: INADEQUATE SEALING AND RETENTION OF THE PLUG CAN RESULT IN OIL LEAKAGE WHICH COULD CAUSE A FIRE IN THE ENGINE COMPARTMENT.
Remedy: DEALERS WILL INSTALL AN EXPANSION PLUG AND RETAINING BRACKET OVER THE CYLINDER HEAD OIL GALLEY PLUG.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA03011 · Auto Trans IGNITION-PARK Interlock
Opened Jul 17, 2003 · Closed Jan 30, 2004
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Additional source detail variants (2)
Power Train:automatic Transmission
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
Power Train:automatic Transmission:lever And Linkage:floor Shift
THE MANUFACTURER REPORTS ABOVE ARE BASED ON DAIMLERCHRYSLER?S (DC) ANALYSIS OF MODEL YEAR (MY) 1998 (POPULATION = 356,384) AND 1999 (POPULATION = 486,948) JA, JX AND LH FAMILY SUBJECT VEHICLE DATA (EARLIER MYS EXCLUDED).THE POPULATION NUMBER INCLUDES ALL MYS.THE PRECISE NUMBER OF DUPLICATES BETWEEN ODI AND DC REPORTS CANNOT BE DETERMINED DUE TO MISSING OR INCOMPLETE INFORMATION.THE FATALITY INCIDENT INVOLVED AN ELDERLY PERSON WHO ATTEMPTED TO STOP A ROLL AWAY VEHICLE AND RECEIVED FATAL INJURIES.ODI ALSO GATHERED INFORMATION ON MY 1997-99 PROWLER VEHICLES IN THIS INVESTIGATION. THE PROWLER VEHICLES WERE MANUFACTURED WITH A DIFFERENT DESIGN SHIFTER MECHANISM (THE SHIFT LEVER IS SHORTER).THERE ARE NO COMPLAINTS OF PROWLER INTERLOCK FAILURE IN ODI?S DATABASE, AND DC HAS RECEIVED NO REPORTS EITHER.THE PROWLER IS EXCLUDED FROM THE RECALL SCOPE.THE INVESTIGATION INVOLVED A CONDITION WHERE THE INTERLOCK SYSTEM COULD FAIL (OR BE MADE INOPERATIVE BY THE OPERATOR) DURING VEHICLE USE, POSSIBLY INADVERTENTLY.THE INTERLOCK SYSTEM IS REQUIRED UNDER FMVSS 114.WITH THE TRANSMISSION IN THE PARK POSITION AND THE IGNITION KEY OFF, THE COMBINED ACTION OF PRESSING THE SHIFT BUTTON AND PULLING THE SHIFT LEVER REARWARD MAY RESULT IN THE OPERATOR OVERCOMING THE INTERLOCK SYSTEM AND CAUSE THE MECHANICAL LINKAGE OF THE SYSTEM TO DISCONNECT.WHEN THIS OCCURS, THERE IS NO OVERT INDICATION TO AN OPERATOR THAT THE SYSTEM IS DEFEATED, AND AN INCREASED RISK OF VEHICLE ROLL-AWAY EXISTS.UNDER RECALL 04V021, DC WILL REPLACE DAMAGED SHIFT MECHANISMS, AND WILL INSTALL ON ALL VEHICLES A DEVICE WHICH INHIBITS THE OPERATOR?S ABILITY TO OVERCOME THE INTERLOCK AND DEFEAT THE SYSTEM.BEGINNING WITH MY 2000, DC INCORPORATED A BRAKE AND TRANSMISSION SHIFTER INTERLOCK (BTSI) SYSTEM INTO THE SUBJECT VEHICLES.INTRODUCTION OF BTSI INVOLVED DESIGN CHANGES TO THE SHIFT MECHANISM, ONE OF WHICH RESULTED IN REDUCED MECHANICAL ADVANTAGE (RMA) OF THE SHIFT BUTTON.THE RMA SHIFTER REQUIRES INCREASED FORCES TO OVERCOME THE INTERLOCK SYSTEM, MAKING THE SHIFTER LESS SUSCEPTIBLE TO DAMAGE.
EA97016 · Lower Control Arm Ball Joint Failure
Opened Sep 29, 1997 · Closed Nov 20, 1997
Status: closed (inferred from source dates) · Suspension
BY LETTER DATED NOVEMBER 6, 1997, THE MANUFACTURER ADVISED THIS AGENCY OF ITS DECISION TO INITIATE A SAFETY RECALL CAMPAIGN OF THE SUBJECT VEHICLES TO CORRECT THE DEFECT IDENTIFIED IN THIS EA.THE RECALL WILL ALSO COVER 1996 AND 1997 CHRYSLER CIRRUS/DODGE STRATUS VEHICLES, AS WELL AS 1995 THROUGH 1997 CHRYSLER SEBRING CONVERTIBLE AND PLYMOUTH BREEZE VEHICLES EQUIPPED WITH IDENTICAL LOWER CONTROL ARM BALL JOINTS.AN ESTIMATED TOTAL OF 599,00VEHICLES ARE AFFECTED BY THIS RECALL.THE MANUFACTURER'S INVESTIGATION DISCLOSED THAT PROCESS VARIABILITY, TOGETHER WITH THE BALL JOINT HOUSING COVER CRIMPING OPERATION, CAN RESULT IN AN INEFFECTIVE SEAL THAT PERMITS A LOSS OF LUBRICATION AND ACCELERTED WEAR OF THE BALL JOINT ASSEMBLY.THIS CONDITION CAN LEAD TO FAILURE AND SEPARTION OF THE LOWER CONTROL ARM BALL JOINT.THE RECALL IS IDENTIFIED AS NHTSA 97V-201 AND A COPY OF CHRYSLER'S LETTER TO NHTSA IS ATTACHED HERETO.