IllustrationAs I was driving my car felt like if it went on neutral. I almost crashed. Stopped. Then it would not come off of park. I kept putting it on drive and it automatically kept going into park mode. The car was still running though. And turns on. It still wont drive. Turns on but doesn't go onto drive mode.
2014 Chrysler 300
Owner reports · Recalls · Investigations
More warning signs than most 300 years
Owner complaints for the 2014 Chrysler 300 are substantially higher than the model-year median of 90.
About this comparison →How this year compares
Owner complaints by model year
Compare all 300 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
650–25K
3925–50K
1950–75K
1475–100K
16100–150K
4150K+
157 reports with mileage · 79 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 72 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 69 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 25 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
22 crash reports4 fire reports9 injury reports
Unknown Or Other complaints
23 reportsValve , computer in transmission stoped working , no communication.
When the weather is very cold or it is raining or snowing my sunroof leaks into my car. The windshield fogs up and I am not able to drive the vehicle and the rear seat and floor is usually wet.
I recently purchased this vehicle used with roughly 50,000k miles and drove it for three weeks with no issue. Suddenly, one morning, the motor would not start when pushing the Start Button. Instead the Start button became locked in the Run position but the engine did not engage. I removed my foot from the brake, pushed Start ag…
Read full complaint
I recently purchased this vehicle used with roughly 50,000k miles and drove it for three weeks with no issue. Suddenly, one morning, the motor would not start when pushing the Start Button. Instead the Start button became locked in the Run position but the engine did not engage. I removed my foot from the brake, pushed Start again and it would not return to the Off position. I opened the door thinking maybe it would reset this problem..... the entire dash Icons, headlights, Nav screen, tachometer, and speedometer start flashing and the windshield wipers are going, while stuck in in the off position. A very low pulsating sound is emanating from the engine compartment. I ran to the trunk to disconnect the battery, with the key fob in my pocket, but the button on lid does not open the lid. I run back to the dash and push the trunk release but received no result. I pulled the rear seats down crawled into the trunk and pulled the emergency trunk release and was finally able to open it. Instead of disconnecting the battery, I attempted to jump it with another vehicle. The vehicle was still in the Run position and all of the other components were continuing to malfunction as stated above. The vehicle "started" and began emmiting exhaust but I still had no response in the gas peddle. I then attempted to turn the vehicle to the off position, which worked only after jumping the vehicle and emitting the exhaust. Once the vehicle was shut off I attempted to restart the vehicle as usually and it worked no problem. It has started and ran fine for 2 days but I am extremely concerned about my safety in driving this vehicle due to reading other consumer experiences with a malfunctioning TIPM in this model and year of vehicle.
The contact owns a 2014 Chrysler 300. The contact stated while driving and making a turn at various speeds, the vehicle stalled. The contact stated that the vehicle failed to restart. The contact stated that the vehicle had to be completely stopped, shifted to park, depress the brake pedal, and then depress the Push-to-Start but…
Read full complaint
The contact owns a 2014 Chrysler 300. The contact stated while driving and making a turn at various speeds, the vehicle stalled. The contact stated that the vehicle failed to restart. The contact stated that the vehicle had to be completely stopped, shifted to park, depress the brake pedal, and then depress the Push-to-Start button to restart the vehicle. The check engine warning light was illuminated. The vehicle was taken to Family Toyota of Arlington, 1661 Wet N Wild Way, Arlington, TX 76011, who was unable to determine the cause of the failure. The vehicle was not repaired. The contact was concerned about driving the vehicle. The dealer referred the contact to the Chrysler. The vehicle was taken to the local dealer, where an unknown diagnosis and repair were completed, but the failure recurred. The manufacturer was contacted, but no assistance was provided. The failure mileage was approximately 43, 000.
The front passenger door panel has separated at the top leaving an open gap between the window and the door. It appears that the rubber molding was not manufactured properly and as heat from the sun warms up the molding, it deforms, pulls up and separates. The problem has continued to worsen over time and is approaching the door…
Read full complaint
The front passenger door panel has separated at the top leaving an open gap between the window and the door. It appears that the rubber molding was not manufactured properly and as heat from the sun warms up the molding, it deforms, pulls up and separates. The problem has continued to worsen over time and is approaching the door locking mechanism. It is also now possible for water to get to the inside of the door. This is a NON-MOVING PART that was defective at the time of manufacture, but took time to malfunction.
My car randomly switches gears by its self . I will put it into drive start driving and it will randomly jerk its self into park and my shifter is electric I believe . This is very unsafe while I’m driving with my family for my car to be switching gears on its own
WHEN I PUT ON MY AC I GET HEAT AND IT GETS SO HOT THAT I HAVE TO CLOSE OFF THE VENT AND OPEN UP THE PASSAGE SIDE TO COOL THE INSIDE OF THE CAR AND I'VE HAD WORK DONE TO THIS THREE TIMES AND I WANT TO KNOW IF ITS ON THE RECALL LIST AND NO ONE TOLD ME SO I NEED HELP WITH THIS PLEASE
MY 300 THE ENGINE LIGHT CAME ON TOOK TO DEALER TO GET LOOKED AT THEY CHANGED OXYGEN SENSOR THEN ABOUT 2 WEEKS OF OWNING THE CAR MY ENGINE SHUT OFF WHILE DRIVING ON FREEWAY COAST OFF TO THE SHOULDER TO GET OUT OF TRAFFIC WITHOUT BEING HIT (SCARY) YOU HAVE TO COME TO COMPLETE STOP PUT IN PARK FOOT ON BRAKE RESTART PUSH BUTTON…
Read full complaint
MY 300 THE ENGINE LIGHT CAME ON TOOK TO DEALER TO GET LOOKED AT THEY CHANGED OXYGEN SENSOR THEN ABOUT 2 WEEKS OF OWNING THE CAR MY ENGINE SHUT OFF WHILE DRIVING ON FREEWAY COAST OFF TO THE SHOULDER TO GET OUT OF TRAFFIC WITHOUT BEING HIT (SCARY) YOU HAVE TO COME TO COMPLETE STOP PUT IN PARK FOOT ON BRAKE RESTART PUSH BUTTON TOOK BACK WHERE I BOUGHT THE CAR FAMILY TOYOTA TAKE IT TO DON DAVIS CHRYSLER SO I DID WORKED ON IT FOR THREE DAYS THEY THINK THEY GOT IT FIXED A MONTH LATER GOING INTO DALLAS IT STALLED OUT AGAIN IT WAS RUSH TO GET TO BI TOOK BACK TO DEALER, DON DAVIS THEY HAD THREE DAYS THEY DID NOT KNOW WHAT WAS CAUSING IT THEY THOUGHT HAD IT FIXED SO ABOUT 3 WEEKS LATER IT HAPPENS AGAIN ENGINE SHUTS OFF NO WARNING SO AND PULL OFF TO SHOULDER COULDN'T MISS TIME AT WORK AROUND FEB 15TH 2018 IT HAPPENED AGAIN WAS TRAVELING ABOUT 60 MILES AN HOUR ON INTERSTATE 30 AND TRAFFIC TRUCK ON MY TAIL AND MY CAR SHUT OFF IMAGINED TO ESCAPE GETTING HIT BEEN GOING ON FOR MONTHS AT LEAST 9 TO 10 TIMES THIS HAS HAPPENED BACK TO DON DAVIS FOR THREE DAYS CALLED ME THEY DID NOT KNOW WHAT WAS CAUSING IT AND TRIED TO SELL ME A DIFFERENT CAR ,,,BECAUSE THIS WAS A DEATH TRAP I SAID NO I LOVE MY CAR FIX IT I REFUSED TO TAKE IT BACK THREE HOURS LATER DEALERSHIP CALLED ME BACK AND SAID WE THINK WE HAVE IT FIXED COME PICK IT UPSO I DID ONLY TO DISCOVER IT DID IT AGAIN AND AGAIN AND AGAINI DO NT FEEL SAFE HAVING ANY FAMILY MEMBER IN MY CAR FOR FEAR OF PUTTING THEIR LIFEIN DANGER SO JUST RECENTLY I TOOK TO AUTO NATION TO GET AIR BAG RECALL HAD THEM CHECK IT OUT THEY SAID THEY THINK IT IS CATALYTIC CONVERTER BUT DID NOT K ITS OUT OF WARRANTY AND G COST ME 3200 DOLLARS I FEEL IF I KEEP DRIVING THIS CAR I AM GOING BECOME A STATISTIC GET KILLED ,,,CRAZY,,, ,,, HAPPENS WHEN VEHICLE IS IN MOTION I WILL PUT THE DATE OF THE BEEN PROBABLY AROUND SEPT 10TH 2017. *TR
I WAS DRIVING STRAIGHT FORWARD AT ABOUT 20MPH ON A BRIDGE WHERE THE ROAD WAS CLEAR WITH NO ICE OR SNOW AND MY CAR DID A 360 SPIN OUT IN THE MIDDLE OF TRAFFIC. THAT DAY I TOOK MY CAR INTO DISCOUNT TIRES WHERE I WAS TOLD I HAD 5/32 THREAD WHICH IS FAIRLY GOOD I STILL WENT AHEAD AND GOT NEW TIRES BUT STILL FELT LIKE MY TIRES WAS NO…
Read full complaint
I WAS DRIVING STRAIGHT FORWARD AT ABOUT 20MPH ON A BRIDGE WHERE THE ROAD WAS CLEAR WITH NO ICE OR SNOW AND MY CAR DID A 360 SPIN OUT IN THE MIDDLE OF TRAFFIC. THAT DAY I TOOK MY CAR INTO DISCOUNT TIRES WHERE I WAS TOLD I HAD 5/32 THREAD WHICH IS FAIRLY GOOD I STILL WENT AHEAD AND GOT NEW TIRES BUT STILL FELT LIKE MY TIRES WAS NOT MOVING LIKE IT SHOULD. I THEN TOOK IT INTO A MECHANIC SHOP WHICH WAS MONTES CAR SHOP IN NORTH MPLS WE DID A TEST DRIVE AND REALIZED MY FRONT WHEELS WERE NOT ENGAGING THE ONLY TIRES THAT WERE SPINNING WAS THE BACK WHEELS. SO AT THAT POINT THEY RAN A ABS DIAGNOSTIC THERE WERE CODES NO SHOWING REGARDING MY AWD AT ALL, SO THEY DID A FULL INSPECTION AND STATED IT WAS A BLOWN MINI FUSE THAT OPERATES THE FRONT DIFF ACTUATOR AND REPLACED IT. I'VE DRIVEN THE CAR AND I AM NOT SURE IF THE PROBLEM HAS BEEN FIXED NOT ONLY THAT THE CAR IS NOT GIVING OFF ANY SENSORS OR CODES REGARDING MY AWD NOT WORKING WHICH IS VERY DANGEROUS AND LIFE THREATENING THERE SHOULD BE SOME WAY FOR THE CAR TO HAVE SENSORS NOTIFYING ME THE MY ALL WHEEL DRIVE IS NOT WORKING OR ENGAGING.
Official recalls
719V018000 · Air Bags:frontal:passenger Side:inflator Module
Jan 15, 2019
Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.
18V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
17V741000 · Electrical System:alternator/generator/regulator
Nov 21, 2017
Chrysler (FCA US LLC) is recalling certain 2014 Dodge Challenger, Charger, Durango, Chrysler 300, and Jeep Grand Cherokee vehicles equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the alternator, free of charge. The recall began December 15, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T75.
17V435000 · Electrical System:alternator/generator/regulator
Jul 10, 2017
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L engine and a 160, 180 or 220 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will inspect the alternator and depending on the part number, will replace the alternator, if necessary, free of charge. The recall began February 12, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T36.
17V097000 · Power Train:axle Assembly:axle Shaft
Feb 14, 2017
Chrysler (FCA US LLC) is recalling certain 2014-2017 Dodge Charger and Chrysler 300 vehicles equipped with all-wheel drive (AWD). The front driveshaft bolts may loosen and allow the front driveshaft to disconnect, potentially causing a loss of motive power.
Consequence & remedy
Consequence: A loss of motive power can increase the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace all eight front driveshaft bolts, free of charge. The recall began April 7, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T03.
16V240000 · Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Apr 25, 2016
Chrysler (FCA US LLC) is recalling certain model year 2012-2014 Dodge Charger and Chrysler 300 vehicles manufactured February 15, 2011, to November 27, 2014, and 2014-2015 Jeep Grand Cherokee vehicles manufactured July 16, 2012, to December 22, 2015. The affected vehicles, equipped with an eight-speed automatic transmission and a monostable gear selector, may not adequately warn the driver when driver's door is opened and the vehicle is not in PARK, allowing them to exit the vehicle while the vehicle is still in gear.
Consequence & remedy
Consequence: Drivers thinking that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software to mitigate the risk of vehicle rollaway, free of charge. The recall began on June 24, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S27. Note: On October 19, 2016 Chrysler identified some previously repaired vehicles did not receive the complete software updates. Chrysler will renotify the affected owners, and dealers will update the software again.
14V634000 · Electrical System:alternator/generator/regulator
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2014 Chrysler 300, Dodge Charger, Challenger, and Durango; and 2012-2014 Jeep Grand Cherokee vehicles manufactured April 22, 2010, to January 2, 2014, and equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.
Remedy: Chrysler has notified owners, and dealers will replace the alternator, free of charge. The recall began on February 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P60.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA16002 · Vehicle Rollaway, Engine On
Opened Feb 3, 2016 · Closed Jun 24, 2016
Status: closed (inferred from source dates) · Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.
Additional source detail variants (2)
Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.
Power Train:automatic Transmission:gear Position Indication (prndl)
On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.