← New search

2014 Chrysler 300

Owner reports · Recalls · Investigations

More warning signs than most 300 years

Owner complaints for the 2014 Chrysler 300 are substantially higher than the model-year median of 90.

About this comparison →

When problems were reported

Mileage at the reported incident

157 reports with mileage · 79 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Electrical System. Review the 72 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Power Train. Review the 69 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 25 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

22 crash reports4 fire reports9 injury reports

Electrical System complaints

72 reports
Clear category filter
29,000 miles · Mar 27, 2017
Electrical SystemPower Train

TL* THE CONTACT OWNS A 2014 CHRYSLER 300. AFTER THE GEAR SHIFT WAS SWITCHED FROM THE PARK POSITION, THE VEHICLE HESITATED TO SHIFT AND THE SERVICE TRANSMISSION AND SHIFTER MALFUNCTION ERROR MESSAGES ILLUMINATED. ON ANOTHER OCCASION, THE VEHICLE HESITATED TO RESPOND WHEN THE ACCELERATOR PEDAL WAS DEPRESSED AND THE INSTRUMENT PANE…

Read full complaint

TL* THE CONTACT OWNS A 2014 CHRYSLER 300. AFTER THE GEAR SHIFT WAS SWITCHED FROM THE PARK POSITION, THE VEHICLE HESITATED TO SHIFT AND THE SERVICE TRANSMISSION AND SHIFTER MALFUNCTION ERROR MESSAGES ILLUMINATED. ON ANOTHER OCCASION, THE VEHICLE HESITATED TO RESPOND WHEN THE ACCELERATOR PEDAL WAS DEPRESSED AND THE INSTRUMENT PANEL BECAME INOPERABLE. THE CONTACT ALSO STATED THAT AFTER THE VEHICLE WAS PARKED, IT FAILED TO RESTART. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE VIN WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 16V240000 (POWER TRAIN). THE FAILURE MILEAGE WAS 29,000.

NHTSA ODI #10968785

17,000 miles · Mar 21, 2017
Electrical SystemPower TrainUnknown Or Other

I PURCHASED THIS CHRYSLER 300 IN 2014 AND PAID CASH 25,000 AND ONLY HAVE 17,000 BECAUSE I FEAR FOR MY LIFE TO DRIVE IT. ON SEVERAL OCCASION MY VEHICLE HAS STOPPED WHILE IN MOTION WITHOUT WARNING AND THE GEAR SLIPS FROM DRIVE TO PARK. WHILE EXITING MY VEHICLE AFTER I HAVE PARKED MY CAR SLIPS INTO DRIVE CAUSING ME TO STUMBLE. ON …

Read full complaint

I PURCHASED THIS CHRYSLER 300 IN 2014 AND PAID CASH 25,000 AND ONLY HAVE 17,000 BECAUSE I FEAR FOR MY LIFE TO DRIVE IT. ON SEVERAL OCCASION MY VEHICLE HAS STOPPED WHILE IN MOTION WITHOUT WARNING AND THE GEAR SLIPS FROM DRIVE TO PARK. WHILE EXITING MY VEHICLE AFTER I HAVE PARKED MY CAR SLIPS INTO DRIVE CAUSING ME TO STUMBLE. ON TWO SEPARATE OCCASIONS I HAD TO CALL A TOW TRUCK TO AID ME BECAUSE MY VEHICLE WOULD STOP WITH WARNING. ONCE WHILE DRIVING ON A HIGHWAY MY CAR STOPPED WHILE TRAVELING AT A HIGH RATE OF SPEED AND WENT INTO PARK ON ITS OWN, I NOTIFIED THE TOWING COMPANY AND IT HAD TO BE TOWED TO A DEALERSHIP. WHILE AT A DEALERSHIP I WAS NOTIFIED OF A DEFECT AND THEY STATED THEY WOULD FIX IT. ON A SECOND OCCASION WHILE ATTEMPTING TO PARK IN MY DRIVEWAY THE CAR CONTINUED TO PUT ITSELF IN PARK AND WHILE TRYING TO REVERSE MY CAR WENT INTO PARK. AFTER SEVERAL ATTEMPTS I AGAIN CONTACTED A TOWING COMPANY WHERE THEY TOWED ME TO ANOTHER DEALERSHIP WHERE THEY AGAIN ATTEMPTED TO FIX THE TRANSMISSION. AGAIN AFTER 2 YEARS I AM STILL FEARFUL TO DRIVE MY VEHICLE. I HAVE MADE ATTEMPTS TO CONTACT THE DEALERSHIP TO NO AVAIL. MY VEHICLE CONTINUES TO MOVE FROM DRIVE TO PARK AND VISE VERSA. PLEASE HELP I HAVE NO OTHER MEANS OF TRANSPORTATION, MY HUSBAND HAS RECENTLY BEEN DIAGNOSED WITH PROSTATE CANCER AND I NEED THIS VEHICLE IN ORDER TO WORK AND TAKE HIM TO HIS DOCTOR'S APPOINTMENT. AT THIS RATE WE WILL BOTH NEED DOCTORS IF I'M NOT DEAD FIRST. THIS IS MY FINAL ATTEMPT TO GET ASSISTANCE WITH VEHICLE MAINTENANCE AND REPAIRS. ALTHOUGH THE DEALERSHIP HAS MADE ATTEMPTS TO REMEDY THIS SITUATION, I CONTINUE TO HAVE PROBLEMS WITH THE TRANSMISSION. I AM COMPLETELY TERRIFIED TO DRIVE MY VEHICLE EACH TIME I DRIVE.

NHTSA ODI #10967618

Mileage unknown · Feb 17, 2017
Electrical SystemSteeringVehicle Speed Control

I PURCHASED MY 2014 CHRYSLER 300C BRAND NEW FROM A CHRYSLER DODGE AND JEEP CERTIFIED DEALERSHIP. SINCE THE FIRST DAY I PURCHASED THE VEHICLE I HAVE BEEN HAVING PROBLEMS. FIRST STARTED WITH THE REAR WINDOW SHADE MALFUNCTIONING WHILE DRIVING AND FRONT DRIVER SEAT WOULD NOT MOVE FORWARD OR REVERSE THE SAME DAY I BOUGHT THE CAR, DEA…

Read full complaint

I PURCHASED MY 2014 CHRYSLER 300C BRAND NEW FROM A CHRYSLER DODGE AND JEEP CERTIFIED DEALERSHIP. SINCE THE FIRST DAY I PURCHASED THE VEHICLE I HAVE BEEN HAVING PROBLEMS. FIRST STARTED WITH THE REAR WINDOW SHADE MALFUNCTIONING WHILE DRIVING AND FRONT DRIVER SEAT WOULD NOT MOVE FORWARD OR REVERSE THE SAME DAY I BOUGHT THE CAR, DEALER SAID THEY WOULD FIX. TOOK MORE THAN TWO TRIPS TO DEALER TO GET THE PROBLEM RESOLVED. NEXT AT AROUND 6000 MILES I HAD CYLINDERS MISFIRE WHILE DRIVING, TOOK ME MORE THAN 3 TRIPS TO DIFFERENT DEALERS TO GET PROBLEM RESOLVED. THEY DID NOT TELL ME WHAT CAUSED THE PROBLEM, JUST FIXED IT. ABOUT A MONTH LATER I HAD ALOT OF SMOKE AND BURNT SMELL COMING FROM MY ENGIN WHILE DRIVING, DEALER SAID A GASKET WAS MISSING. I HAD AIR COMING THROUGH DRIVER FRONT AND REAR DOORS. TOOK THE CAR TO DEALER TO GET FIXED, SUPPOSIBLY THEY FIXED THE PROBLEM BUT TO THIS DATE I'M HAVING THE SAME PROBLEM WITH AIR COMING THROUGH DOORS AS I'M DRIVING, NOW THE WORSE PROBLEMS ARE HAPPENING.ON MID 2016 THE RACK AND PINION GAVE OUT. ON SEPTEMBER OF 2016 ALL MY ELECTRICAL SYSTEM STARTED TO GO HAYWIRE, WINDSHIELD WIPERS ON AND OFF BY THEMSELVES, GAUGES GOING UP AND DOWN, TRANSMISSION SHIFTING BY ITSELF, LIGHTS ON AND OFF ETC, THIS HAPPEND WHILE DRIVING ON CITY STREETS, WE PULLED OVER TURNED OFF THE CAR, TURNED IT BACK ON STEERING WHEEL WAS VERY HARD TO TURN. TOOK TO DEALER. THEY SAID IT WAS POWER STEERING PUMP. SO THEY REPLACED. ABOUT A MONTH LATER MY WIFE WAS DRIVING AND THE CAR ACCELERATED TO HI RATE OF SPEED BY ITSELF. AFTER SHE GAINED CONTROL SHE DROVE HOME. NOW 2 DAYS AGO WE HAD THE SAME ELECTRICAL HAYWIRE MALFUNCTION, THIS TIME AS ALL OTHER ELECTRICAL THINGS THAT HAPPENED AS LAST TIME THE CAR ACCELERATED BY ITSELF, WE PULLED OVER TO GAS STATION, TRIED TO TURN ON AND CAR WAS DEAD, HAD CHECK ENGINE LIGHT AND ETC LIGHT ON.THIS CAR HAS BECOME VERY DANGEROUS FOR MY FAMILY.

NHTSA ODI #10955219

35,000 miles · Sep 9, 2016
Electrical System

TL* THE CONTACT OWNS A 2014 CHRYSLER 300. WHILE DRIVING 40 MPH, THE BATTERY SAVE MODE WARNING INDICATOR ILLUMINATED. THE FAILURE RECURRED FOUR TIMES. THE VEHICLE WAS TOWED TO A DEALER WHERE IT WAS DIAGNOSED THAT THE BATTERY FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILURE RECURRED. THE MANUFACTURE…

Read full complaint

TL* THE CONTACT OWNS A 2014 CHRYSLER 300. WHILE DRIVING 40 MPH, THE BATTERY SAVE MODE WARNING INDICATOR ILLUMINATED. THE FAILURE RECURRED FOUR TIMES. THE VEHICLE WAS TOWED TO A DEALER WHERE IT WAS DIAGNOSED THAT THE BATTERY FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS REPAIRED; HOWEVER, THE FAILURE RECURRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 35,000.

NHTSA ODI #10904969

8,000 miles · Aug 25, 2016
Electrical SystemPower Train

TL* THE CONTACT OWNS A 2014 CHRYSLER 300. THE CONTACT STATED THAT THE VEHICLE INDEPENDENTLY SHIFTED TO NEUTRAL WHILE THE VEHICLE WAS BEING STOPPED. THE FAILURE OCCURRED WITHOUT WARNING. THE VEHICLE WAS NOT DIAGNOSED NOR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 8,000.

NHTSA ODI #10898603

Mileage unknown · Jul 18, 2016
Electrical System

THE MIL CAME ON AS I TURNED ON MY CAR ONE DAY AFTER WORK. I HAD FLIPPED THROUGH THE VEHICLE INFO AND NOTICED THAT THE OIL PRESSURE WAS AT 99. I WENT TO GET THE CODE READ AND FOUND OUT THAT IT WAS THE OIL PRESSURE SENDING UNIT THAT IS MALFUNCTIONED. I HAVE READ FORUM AFTER FORUM REGARDING CHRYSLER 300 VEHICLES RANGING FROM YEARS …

Read full complaint

THE MIL CAME ON AS I TURNED ON MY CAR ONE DAY AFTER WORK. I HAD FLIPPED THROUGH THE VEHICLE INFO AND NOTICED THAT THE OIL PRESSURE WAS AT 99. I WENT TO GET THE CODE READ AND FOUND OUT THAT IT WAS THE OIL PRESSURE SENDING UNIT THAT IS MALFUNCTIONED. I HAVE READ FORUM AFTER FORUM REGARDING CHRYSLER 300 VEHICLES RANGING FROM YEARS 2011-2014 AND HAVE FOUND THAT THIS IS A COMMON PROBLEM. WILL THE DEALERSHIP REPLACE THE UNIT FOR FREE?

NHTSA ODI #10885584

12,000 miles · Jul 18, 2016
Electrical System

TL* THE CONTACT OWNS A 2014 CHRYSLER 300. WHEN THE FOB KEY WAS REMOVED FROM THE VEHICLE, THE ENGINE WAS STILL RUNNING. THE "KEY REMOVED FROM THE VEHICLE" WARNING INDICATOR WAS ILLUMINATED. THE VEHICLE WAS NOT DIAGNOISED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 12,000.

NHTSA ODI #10885451

19,000 miles · Jul 15, 2016
Electrical System

I WAS TOLD THAT THE CHRYSLER 300, 2014, WAS UNDER RECALL, BUT I WAS NEVER NOTIFIED OF THE RECALL, I ASSUME, SINCE THE CAR WAS UNDER A LEASE AGREEMENT. THE PROBLEM I EXPERIENCED ONE DAY WAS THE THE CAR WOULD NOT START AND THE CAR HAD TO BE TOWED. DURING THE TOWING, THE CAR WAS DAMAGED IN THE FRONT END AND NOW RATTLES ON THE LEFT…

Read full complaint

I WAS TOLD THAT THE CHRYSLER 300, 2014, WAS UNDER RECALL, BUT I WAS NEVER NOTIFIED OF THE RECALL, I ASSUME, SINCE THE CAR WAS UNDER A LEASE AGREEMENT. THE PROBLEM I EXPERIENCED ONE DAY WAS THE THE CAR WOULD NOT START AND THE CAR HAD TO BE TOWED. DURING THE TOWING, THE CAR WAS DAMAGED IN THE FRONT END AND NOW RATTLES ON THE LEFT FRONT WHEN THE CAR HITS A BUMP IN THE ROAD. THIS CAR NEEDS TO BE INSPECTED AND THE DAMAGE REPAIRED SINCE THE DAMAGE AFFECTS THE PERFORMANCE OF THE CAR. IN ADDITION, THE ORIGINAL PROBLEM CAUSED THE CAR TO BE SCRATCHED IN SEVERAL PLACES AND COST ME A GREAT DEAL OF TIME AND MONEY. PLEASE CONTACT ME SO THESE PROBLEMS MAY BE RESOLVED BY THE DEALER THAT HANDLED THE REPAIR, WHICH WAS HAYES CHRYSLER.

NHTSA ODI #10884978

13,000 miles · May 31, 2016
Electrical System

ON ONE OCCASION MY VEHICLE'S SCREEN TURNED WHITE AND RESTARTED WITHOUT WARNING. ANOTHER OCCASION WHILE TRYING TO USE THE HEAT, THE VEHICLE CONTINUED TO BLOW OUT COLD AIR AFTER TURNING THE HEAT TO HIGH. THE PROBLEM DID NOT CORRECT ITSELF UNTIL THE VEHICLE WAS TURNED OFF AND TURNED BACK ON A SHOT TIME LATER. THE SAME OCCURRENCE HA…

Read full complaint

ON ONE OCCASION MY VEHICLE'S SCREEN TURNED WHITE AND RESTARTED WITHOUT WARNING. ANOTHER OCCASION WHILE TRYING TO USE THE HEAT, THE VEHICLE CONTINUED TO BLOW OUT COLD AIR AFTER TURNING THE HEAT TO HIGH. THE PROBLEM DID NOT CORRECT ITSELF UNTIL THE VEHICLE WAS TURNED OFF AND TURNED BACK ON A SHOT TIME LATER. THE SAME OCCURRENCE HAPPENED WITH THE A/C NOT WORKING UNTIL THE VEHICLE WAS TURNED OFF AND THEN RESTARTED A SHORT TIME LATER.

NHTSA ODI #10871616

100 miles · Nov 14, 2015
Electrical SystemPower Train

COMPASS DIRECTION WRONG. GARAGE DOOR IN CAR BUTTON OCCASIONALLY DOES NOT WORK. OCCASIONAL LOSS OF RADIO. REAR OF CAR BUMP SOUND ON START UP. UNEVEN DRIVE WITH SMALL JERK WHEN GOING FROM START TO ACCELERATING ALL OF ABOVE ON INITIAL START UP.

NHTSA ODI #10790354

Official recalls

7

19V018000 · Air Bags:frontal:passenger Side:inflator Module

Jan 15, 2019

Chrysler (FCA US LLC) is recalling certain 2010 Dodge Ram 3500, Ram 4500/5500, 2010-2011 Dodge Dakota, 2010-2014 Dodge Challenger, 2010-2015 Dodge Challenger, Chrysler 300, and 2010-2016 Jeep Wrangler vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to explode.

Consequence & remedy

Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could explode with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.

Remedy: Owners are advised not to drive their vehicle until the recall repair is complete. Chrysler will notify owners, and dealers will replace the passenger frontal air bag inflator, free of charge. The recall began February 4, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V01.

18V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control

May 17, 2018

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence & remedy

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Additional source detail variants (3)

Electrical System:software

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Vehicle Speed Control:cruise Control

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

Electrical System:wiring

Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.

Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.

Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.

17V741000 · Electrical System:alternator/generator/regulator

Nov 21, 2017

Chrysler (FCA US LLC) is recalling certain 2014 Dodge Challenger, Charger, Durango, Chrysler 300, and Jeep Grand Cherokee vehicles equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.

Consequence & remedy

Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace the alternator, free of charge. The recall began December 15, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T75.

17V435000 · Electrical System:alternator/generator/regulator

Jul 10, 2017

Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Challenger, Dodge Charger, Chrysler 300, Dodge Durango, and 2012-2014 Jeep Grand Cherokee vehicles. The affected vehicles have electro-hydraulic power steering (EHPS) and are equipped with a 5.7L or a 3.6L engine and a 160, 180 or 220 amp alternator. In the affected vehicles, the alternator may suddenly fail.

Consequence & remedy

Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.

Remedy: Chrysler will notify owners, and dealers will inspect the alternator and depending on the part number, will replace the alternator, if necessary, free of charge. The recall began February 12, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T36.

17V097000 · Power Train:axle Assembly:axle Shaft

Feb 14, 2017

Chrysler (FCA US LLC) is recalling certain 2014-2017 Dodge Charger and Chrysler 300 vehicles equipped with all-wheel drive (AWD). The front driveshaft bolts may loosen and allow the front driveshaft to disconnect, potentially causing a loss of motive power.

Consequence & remedy

Consequence: A loss of motive power can increase the risk of a crash.

Remedy: Chrysler will notify owners, and dealers will replace all eight front driveshaft bolts, free of charge. The recall began April 7, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T03.

16V240000 · Power Train:automatic Transmission:control Module (tcm/pcm/tecm)

Apr 25, 2016

Chrysler (FCA US LLC) is recalling certain model year 2012-2014 Dodge Charger and Chrysler 300 vehicles manufactured February 15, 2011, to November 27, 2014, and 2014-2015 Jeep Grand Cherokee vehicles manufactured July 16, 2012, to December 22, 2015. The affected vehicles, equipped with an eight-speed automatic transmission and a monostable gear selector, may not adequately warn the driver when driver's door is opened and the vehicle is not in PARK, allowing them to exit the vehicle while the vehicle is still in gear.

Consequence & remedy

Consequence: Drivers thinking that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.

Remedy: Chrysler will notify owners, and dealers will update the vehicle software to mitigate the risk of vehicle rollaway, free of charge. The recall began on June 24, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S27. Note: On October 19, 2016 Chrysler identified some previously repaired vehicles did not receive the complete software updates. Chrysler will renotify the affected owners, and dealers will update the software again.

14V634000 · Electrical System:alternator/generator/regulator

Oct 8, 2014

Chrysler Group LLC (Chrysler) is recalling certain model year 2011-2014 Chrysler 300, Dodge Charger, Challenger, and Durango; and 2012-2014 Jeep Grand Cherokee vehicles manufactured April 22, 2010, to January 2, 2014, and equipped with a 3.6L engine and a 160 amp alternator. In the affected vehicles, the alternator may suddenly fail.

Consequence & remedy

Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash.

Remedy: Chrysler has notified owners, and dealers will replace the alternator, free of charge. The recall began on February 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P60.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

EA16002 · Vehicle Rollaway, Engine On

Opened Feb 3, 2016 · Closed Jun 24, 2016

Status: closed (inferred from source dates) · Power Train:automatic Transmission:gear Position Indication (prndl)

On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.

Additional source detail variants (2)

Power Train:automatic Transmission:gear Position Indication (prndl)

On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.

Power Train:automatic Transmission:gear Position Indication (prndl)

On April 22, 2016, Fiat Chrysler Automotive US LLC, (FCA) submitted a Defect Information Report (DIR) to NHTSA regarding a defect that could result in unattended vehicle rollaway with the engine running in approximately 811,586 model year (MY) 2012 to 2014 Dodge Charger and Chrysler 300 vehicles and MY 2014 to 2015 Jeep Grand Cherokee vehicles equipped with 8-speed transmissions and a monostable gear selector (NHTSA Recall #16V-240, FCA Recall #S27). According to FCA's DIR, The existing strategies built into these vehicles to deter drivers from exiting the vehicle after failing to put the transmission into PARK have not stopped some from doing so. Drivers erroneously concluding that their vehicle's transmission is in the PARK position may be struck by the vehicle and injured if they attempt to get out of the vehicle while the engine is running and the parking brake is not engaged.The vehicles recalled by FCA are equipped with Monostable electronic (shift-by-wire) gearshift assemblies supplied by ZF Group (see Figure 1).The subject Monostable shifter has a single neutral position that it snaps back to when the driver releases the shift knob.Although the Monostable gearshift has the familiar appearance of a conventional console mechanical gearshift assembly, it has an unfamiliar movement that does not provide the tactile or visual feedback that drivers are accustomed to receiving from conventional shifters.Consequently, the driver must take additional time to verify that the desired gear position was achieved by checking the PRNDL display on the shift knob or the Electronic Vehicle Information Center (EVIC) display.