NHTSA owner reports · September 18, 2026 snapshot.
Power Train complaints
7 reportsClear category filter169,000 miles · Oct 7, 2021
EnginePower Train
The contact owns a 2008 Chevrolet Suburban. The contact stated that while driving at various speeds, the vehicle would shut off without warning. The contact had taken the vehicle to an independent mechanic who was unable to diagnose the failure. The contact has had multiple repairs performed on the engine; however, the failure p…
Read full complaint
The contact owns a 2008 Chevrolet Suburban. The contact stated that while driving at various speeds, the vehicle would shut off without warning. The contact had taken the vehicle to an independent mechanic who was unable to diagnose the failure. The contact has had multiple repairs performed on the engine; however, the failure persisted. The dealer nor the manufacturer were notified of the failure. The vehicle was not repaired. The failure mileage was approximately 169,000.
NHTSA ODI #11435851
140,000 miles · Mar 31, 2021
Air BagsPower TrainCrashInjury
TL* THE CONTACT OWNED A 2008 CHEVROLET SUBURBAN. THE CONTACT STATED WHILE DRIVING AT 55 MPH, THE REAR AXLE FRACTURED. AS A RESULT, THE BRAKES WOULD NOT ENGAGE WHEN THE BRAKES WERE SUPPRESSED CAUSING THE CONTACT TO CRASH INTO A CONCRETE BARRIER. THE AIR BAGS FAILED TO DEPLOY. A POLICE REPORT WAS FILED.THE CONTACT SUSTAINED A BROK…
Read full complaint
TL* THE CONTACT OWNED A 2008 CHEVROLET SUBURBAN. THE CONTACT STATED WHILE DRIVING AT 55 MPH, THE REAR AXLE FRACTURED. AS A RESULT, THE BRAKES WOULD NOT ENGAGE WHEN THE BRAKES WERE SUPPRESSED CAUSING THE CONTACT TO CRASH INTO A CONCRETE BARRIER. THE AIR BAGS FAILED TO DEPLOY. A POLICE REPORT WAS FILED.THE CONTACT SUSTAINED A BROKEN WRIST AND NECK SORENESS. THE CONTACT DID NOT SEEK ANY MEDICAL ATTENTION. THE VEHICLE WAS NOT DRIVABLE AND WAS TOWED TO HER HOME ADDRESS. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. A DEALER WAS NOT CONTACTED. THE MANUFACTURER HAD NOT BEEN INFORMED OF FAILURE. THE FAILURE MILEAGE WAS 140,000.
NHTSA ODI #11405862
152,000 miles · May 29, 2019
Electrical SystemElectronic Stability Control (esc)Power Train
MY GAUGES ARE DOING ALL TYPES OF CRAZY THINGS BLINKING ON AND OFF I REPLACE MY PCM AND BODY CONTROL MODULE AND STILL HAVING PROBLEMS THIS GMC IS NOT DRIVE ABLE AND IT SHOULD BE A RECALL I HAVE SPENT OVER $2000 IN THE SHOP
NHTSA ODI #11210741
145,000 miles · Aug 19, 2016
EnginePower Train
I WAS DRIVING MY VEHICLE SEVERAL DAYS AFTER HAVING A ROUTINE OIL CHANGE AND THE VEHICLE STARTED TO SLOW DOWN. I TOOK MY CAR IN TO BE CHECKED OUT AND WAS TOLD THAT I NEED A NEW ENGINE, THE TRUCK HAS A LOSS OF POWER DUE TO THE STABILIZING TRAK ISSUE. AFTER READING ALL THE COMPLAINTS ONLINE THIS SEEMS TO BE A PROBLEM WHICH NEEDS …
Read full complaint
I WAS DRIVING MY VEHICLE SEVERAL DAYS AFTER HAVING A ROUTINE OIL CHANGE AND THE VEHICLE STARTED TO SLOW DOWN. I TOOK MY CAR IN TO BE CHECKED OUT AND WAS TOLD THAT I NEED A NEW ENGINE, THE TRUCK HAS A LOSS OF POWER DUE TO THE STABILIZING TRAK ISSUE. AFTER READING ALL THE COMPLAINTS ONLINE THIS SEEMS TO BE A PROBLEM WHICH NEEDS TO BE ADDRESSED BY CHEVY.
NHTSA ODI #10897270
135,000 miles · Sep 8, 2014
Power Train
TORT CONVERTER ON TRANSMISSION WAS SHOT...HAD TO REPLACE ENTIRE TRANSMISSION AT 135,000 MILES. *TR
NHTSA ODI #10631441
Mileage unknown · May 13, 2014
Electrical SystemEnginePower Train
2008 CHEVROLET SUBURBAN. CONSUMER WRITES IN REGARDS TO THE DISAPPOINTMENT IN THE MANUFACTURER DUE TO NUMEROUS VEHICLE REPAIRS. *SMD THE CONSUMER STATED THE VEHICLE WOULD RUN ROUGH, THE CHECK ENGINE LIGHT ILLUMINATED, THE SERVICE STABILITRAK AND TRACTION CONTROL LIGHTS ILLUMINATED WHEN SOME OF THE CYLINDERS SHUT DOWN, THE LIF…
Read full complaint
2008 CHEVROLET SUBURBAN. CONSUMER WRITES IN REGARDS TO THE DISAPPOINTMENT IN THE MANUFACTURER DUE TO NUMEROUS VEHICLE REPAIRS. *SMD THE CONSUMER STATED THE VEHICLE WOULD RUN ROUGH, THE CHECK ENGINE LIGHT ILLUMINATED, THE SERVICE STABILITRAK AND TRACTION CONTROL LIGHTS ILLUMINATED WHEN SOME OF THE CYLINDERS SHUT DOWN, THE LIFTERS WERE NOT PROPERLY LUBRICATED, CAUSING THEM TO FAIL. THE ENGINE CONSUMED LARGE AMOUNTS OF OIL. THERE WERE NOISES COMING FROM THE OIL PAN AND TRANSMISSION AREA, 3 OF THE 4 DOOR LOCKS ACTUATORS WERE REPLACED, THE REAR LIFTGATE BROKE FOR THE 4TH TIME, THE RIGHT RETRACTABLE MIRROR WAS INOPERABLE, THE CRUISE CONTROL WORKED ABOUT 505 OF THE TIME, WHICH WAS PROBABLY TIED THE THROTTLE POSITIONING SENSOR GOING BAD AS WELL. ALSO, THE VEHICLE HAD SIGNIFICANT ELECTRICAL PROBLEM, WHERE CERTAIN LIGHTS WOULD ILLUMINATE ON THE DASHBOARD, THERE WAS AN AUDIBLE CLICKING NOISE, THAT SOUNDED LIKE A RELAY FIRING VERY QUICKLY. *JB
NHTSA ODI #10587971
27,000 miles · Dec 8, 2011
Engine And Engine CoolingPower Train
NEW CAR PURCHASED IN 2008. MULTIPLE ISSUES WITH CAR CONSUMING EXCESS OIL AND LOSING ENGINE POWER. 27,000 MILES HAD TO REPLACE ALL AMF LIFTERS IN ENGINE 29,000 MILES HAD TO REPLACE THROTTLE BODY ASSEMBLY SYSTEM 31,000 MILES HAD TO INSTALL NEW OIL PUMP, GASKET AND SEAL 32,000 MILES HAD TO REPLACE OIL GASKET 37,000 MILES OI…
Read full complaint
NEW CAR PURCHASED IN 2008. MULTIPLE ISSUES WITH CAR CONSUMING EXCESS OIL AND LOSING ENGINE POWER. 27,000 MILES HAD TO REPLACE ALL AMF LIFTERS IN ENGINE 29,000 MILES HAD TO REPLACE THROTTLE BODY ASSEMBLY SYSTEM 31,000 MILES HAD TO INSTALL NEW OIL PUMP, GASKET AND SEAL 32,000 MILES HAD TO REPLACE OIL GASKET 37,000 MILES OIL INTAKE SYSTEM PLUGS BURNING OIL AND OIL ON INTAKE VALVE. HAD TO CLEAN ENGINE AND INSTALLL 8 VALVE SEALS. *TR
NHTSA ODI #10438955
Official recalls
4Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2009 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 23, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on September 20, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, Cadillac customer service at 1-800-458-8006, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328780.
Jun 4, 2010
GM IS RECALLING CERTAIN MODEL YEAR 2006-2009 BUICK, LUCERNE; CADILLAC DTS; HUMMER H2; MODEL YEAR 2008-2009 BUICK ENCLAVE; CADILLAC CTS; MODEL YEAR 2007-2009 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE; GMC ACADIA, SIERRA, YUKON, YUKON XL; SATURN OUTLOOK; AND MODEL YEAR 2009 CHEVROLET TRAVERSE VEHICLES EQUIPPED WITH A HEATED WASHER FLUID SYSTEM (HWFS). A RECALL WAS IMPLEMENTED IN 2008 TO ADD A FUSE TO THE CONTROL CIRCUIT HARNESS TO ADDRESS THE POTENTIAL CONSEQUENCES OF A PRINTED CIRCUIT BOARD (PCB) ELECTRICAL SHORT. HOWEVER, THERE HAVE BEEN NEW REPORTS OF THERMAL INCIDENTS ON HWFS MODULES AFTER THIS IMPROVEMENT WAS INSTALLED. THESE INCIDENTS RESULTED FROM A NEW FAILURE MODE ATTRIBUTED TO THE DEVICE'S THERMAL PROTECTION FEATURE. THE SIGNIFICANCE VARIES FROM MINOR DISTORTION TO CONSIDERABLE MELTING OF THE PLASTIC AROUND THE HWFS FLUID CHAMBER.
Consequence & remedy
Consequence: IT IS POSSIBLE FOR THE HEATED WASHER MODULE TO IGNITE AND A FIRE MAY OCCUR.
Remedy: DEALERS WILL PERMANENTLY DISABLE AND REMOVE THE HEATED WASHER FLUID MODULE. AN UPDATED PAGE FOR THE OWNER MANUAL WILL BE PROVIDED AND INSERTED IN THE OWNER MANUAL TO DOCUMENT THAT THE FEATURE HAS BEEN PERMANENTLY DISABLED AND REMOVED FROM THE VEHICLE. THE SAFETY RECALL BEGAN ON JUNE 11, 2010. OWNERS MAY CONTACT BUICK AT 1-866-608-8080, CADILLAC AT 1-866-982-2339, CHEVROLET AT 1-800-630-2438, SATURN AT 1-800-972-8876, GMC AT 1-866-996-9463 AND HUMMER AT 1-800-732-5493 OR AT THE OWNER CENTER AT WWW.GMOWNERCENTER.COM.
Aug 28, 2008
GM IS RECALLING 857,735 MY 2006-2008 BUICK LUCERNE; CADILLAC DTS; HUMMER H2; MY 2007-2008 CADILLAC ESCALADE, ESCALADE ESV, ESCALADE EXT; CHEVROLET AVALANCHE, SILVERADO, SUBURBAN, TAHOE; GMC ACADIA, SIERRA, YUKON, YUKON XL, SATURN OUTLOOK; AND MY 2008 BUICK ENCLAVE VEHICLES EQUIPPED WITH A HEATED WIPER WASHER FLUID SYSTEM. A SHORT CIRCUIT ON THE PRINTED CIRCUIT BOARD FOR THE WASHER FLUID HEATER MAY OVERHEAT THE CONTROL-CIRCUIT GROUND WIRE.
Consequence & remedy
Consequence: THIS MAY CAUSE OTHER ELECTRICAL FEATURES TO MALFUNCTION, CREATE AN ODOR, OR CAUSE SMOKE INCREASING THE RISK OF A FIRE.
Remedy: DEALERS WILL INSTALL A WIRE HARNESS WITH AN IN-LINE FUSE FREE OF CHARGE. THE RECALL BEGAN ON SEPTEMBER 12, 2008. OWNERS MAY CONTACT BUICK AT 1-866-608-8080; CADILLAC AT 1-800-982-2339 OR HTTP://WWW.CADILLAC.COM; CHEVROLET AT 1-800-630-2438; SATURN AT 1-800-972-8876 OR HTTP://WWW.SATURN.COM, GMC AT 1-866-996-9436; OR HUMMER AT 1-800-732-5493; OR THROUGH THEIR WEBSITE AT <A HREF=HTTP://WWW.GMOWNERCENTER.COM>HTTP://WWW.GMOWNERCENTER.COM</A> .
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration