Illustration2020 3.0 diesel duramax sucked in the antifreeze and caused a hydrolock. The dealer says that it is not covered under warranty since the engine was over 100k miles. They did offer a new engine for $30K which I declined. The truck was always well taken care of and only received the best in all products
2020 Chevrolet Silverado 2500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2020 Chevrolet Silverado 2500 do not stand out strongly from the model-year median of 81.
About this comparison →How this year compares
Owner complaints by model year
Compare all Silverado 2500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
170–25K
225–50K
550–75K
475–100K
5100–150K
2150K+
35 reports with mileage · 70 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Power Train. Review the 31 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 17 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes. Review the 15 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
2 crash reports3 fire reports1 injury reports
Engine complaints
10 reportsThe contact owns a 2020 Chevrolet Silverado 2500. The contact stated that while driving approximately 45 MPH, the check engine warning light illuminated. The vehicle was taken to the residence. The vehicle was then taken to a dealer, and DTC: P133X (Cylinder X Glow Plug Failure) was retrieved. The contact was informed that the G…
Read full complaint
The contact owns a 2020 Chevrolet Silverado 2500. The contact stated that while driving approximately 45 MPH, the check engine warning light illuminated. The vehicle was taken to the residence. The vehicle was then taken to a dealer, and DTC: P133X (Cylinder X Glow Plug Failure) was retrieved. The contact was informed that the Glow Plug needed to be replaced and reprogrammed. The vehicle was repaired, but the failure reoccurred with a different Glow Plug five months later. The vehicle was taken to a dealer to be diagnosed, and it was determinedthat Glow Plug #3 had failed, and DTC: P0673, P0607, and P133A were retrieved. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was 50,616.
The contact owns a 2020 Chevrolet Silverado 2500. The contact stated that while driving at an undisclosed speed, the rear wheels locked up momentarily. The check engine warning light was illuminated. The vehicle was previously taken to the local dealer to be repaired under NHTSA Campaign Number: 24V797000 (Power Train). The vehi…
Read full complaint
The contact owns a 2020 Chevrolet Silverado 2500. The contact stated that while driving at an undisclosed speed, the rear wheels locked up momentarily. The check engine warning light was illuminated. The vehicle was previously taken to the local dealer to be repaired under NHTSA Campaign Number: 24V797000 (Power Train). The vehicle was repaired, but the failure recurred. The manufacturer was contacted, who confirmed that the recall repair was a one-time free repair, and no further assistance was provided. The failure mileage was approximately 188,000.
I am writing to express my serious concern and frustration regarding the unresolved recall on my 2020 Chevrolet Silverado 2500 (VIN: [XXX] ). Despite multiple visits to multiple dealerships, I was repeatedly told that the necessary parts to complete the recall repair were on back order and instructed to “wait for parts.” No inte…
Read full complaint
I am writing to express my serious concern and frustration regarding the unresolved recall on my 2020 Chevrolet Silverado 2500 (VIN: [XXX] ). Despite multiple visits to multiple dealerships, I was repeatedly told that the necessary parts to complete the recall repair were on back order and instructed to “wait for parts.” No interim solution or assistance was ever offered. As a result of this delay, my vehicle broke down without warning, leaving me stranded on the side of the road. This created a hazardous situation and significant disruption to my day. To make matters worse, I had to pay out of pocket to have the truck towed to a repair shop in an effort to get it operational—an expense I should never have incurred given the known recall and repeated attempts to have the issue corrected by Chevrolet. I have been a loyal Chevrolet owner and have always trusted the brand for its quality and dependability. However, this delay and lack of proactive support is causing significant inconvenience and eroding that trust. This situation is unacceptable for several reasons: 1.Safety Risk and Recall Obligation: Chevrolet acknowledged the defect by issuing a recall, yet I have been forced to operate a vehicle that does not meet your own safety standards for months. 2.Repeated Service Attempts with No Resolution: I followed the proper process and visited an authorized dealer multiple times, only to be turned away each time with no solution beyond “wait for parts.” 3.Breakdown and Financial Loss: The vehicle failure and subsequent towing expense are a direct consequence of Chevrolet’s inability to provide timely parts or alternative accommodations. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
I was driving on Interstate 75 in Ohio when the engine suddenly overheated and completely locked up we were pulling my travel trailer camper at the time which we ended up getting off of an overpass and blocking traffic for several hours until we got the vehicles moved Chevrolet did eventually replace the motor and the entire coo…
Read full complaint
I was driving on Interstate 75 in Ohio when the engine suddenly overheated and completely locked up we were pulling my travel trailer camper at the time which we ended up getting off of an overpass and blocking traffic for several hours until we got the vehicles moved Chevrolet did eventually replace the motor and the entire cooling system with what they claim is a new motor in October of 2024, and within the last couple of days I have noticed a smell coming from the engine compartment that was reminiscent about the smell when it locked up I'm afraid they stuck another motor in my truck that has the same exact issues and once it goes out of warranty I'm going to be stuck with another broke down truck
In 2024, I noticed that my truck was experiencing rough shifts. It felt as if the back wheels were jerking over uneven ground, even though the vehicle was on a flat surface. In November 2024, my sister sent me an article about General Motors' massive recall due to rear wheel lock-up, which increased the risk of crashes. I contac…
Read full complaint
In 2024, I noticed that my truck was experiencing rough shifts. It felt as if the back wheels were jerking over uneven ground, even though the vehicle was on a flat surface. In November 2024, my sister sent me an article about General Motors' massive recall due to rear wheel lock-up, which increased the risk of crashes. I contacted GM and learned that my truck was part of the recall. I reported the issues my truck was exhibiting, and GM instructed me to reach out to my dealer about the problem. However, I was informed that they did not have the parts to fix the issue and had no idea when they would receive them. I asked GM if they would provide me with a rental vehicle, but they declined, stating that if they offered a rental to me, they would have to provide one for others as well, which was not feasible due to the large number of affected vehicles. I explained that my truck is my daily driver for work, and I frequently transport my grandchildren in it. Driving the truck was hazardous given the issues it was already exhibiting. I was told to contact my dealer, and since my truck was under warranty, they should provide me with a rental. When I requested to speak with a manager, I was informed that they would only reiterate the same information. I then contacted my dealer, Sapaugh GM Country, located at 1435 McNutt St., Herculaneum, MO. I was informed that they do not have the parts. but they did a minor tweak which has caused more damage to my powertrain and engine.
We just arrived to our out to town destination and exited the vehicle. We drove 80 miles to get there. The truck was running when we noticed white smoke coming from under the hood then immediately large red flames.
The DEF heater/tank shorted out. The DEF system has thrown a code 3 times in the little over a year I’ve owned the truck. This final time I was told that the tank needs to be replaced. The truck has now been in the shop for 2 months and there is still no ship date on the replacement tank. The tanks are on a national back order. …
Read full complaint
The DEF heater/tank shorted out. The DEF system has thrown a code 3 times in the little over a year I’ve owned the truck. This final time I was told that the tank needs to be replaced. The truck has now been in the shop for 2 months and there is still no ship date on the replacement tank. The tanks are on a national back order. From what I understand there are about 9,000 people waiting for this DEF tank countrywide. I now have a $60k work truck that I am paying for but cannot use with no reasonable end in sight.
AFTER OWNING THE BRAND NEW TRUCK FOR LESS THAN 24 HOURS (APPROXIMATELY 170 MILES ON THE ODOMETER OF THE VEHICLE), I WAS DRIVING IN A STRAIGHT LINE ON A 2 LANE HIGHWAY AT APPROX. 50-55MPH. MY FOOT WAS LIGHTLY ON THE ACCELERATOR, MAINTAINING SPEED, AS I HAD JUST PASSED THROUGH A TRAFFIC CIRCLE ABOUT A MILE PRIOR, AND WAS IN A SMAL…
Read full complaint
AFTER OWNING THE BRAND NEW TRUCK FOR LESS THAN 24 HOURS (APPROXIMATELY 170 MILES ON THE ODOMETER OF THE VEHICLE), I WAS DRIVING IN A STRAIGHT LINE ON A 2 LANE HIGHWAY AT APPROX. 50-55MPH. MY FOOT WAS LIGHTLY ON THE ACCELERATOR, MAINTAINING SPEED, AS I HAD JUST PASSED THROUGH A TRAFFIC CIRCLE ABOUT A MILE PRIOR, AND WAS IN A SMALL LINE OF "TRAFFIC" TRAVELLING ON THE ROAD. THE REAR WHEELS BEGAN TO LIGHTLY SHAKE (IT FELT SIMILAR TO DRIVING ON RUMBLE STRIPS) FOR APPROXIMATELY 3-5 SECONDS, THEN SEVERAL WARNING LIGHTS ON THE DASH LIT UP AND THE TRUCK VIOLENTLY "JERKED" THEN PULLED AND DRIFTED ONTO THE RIGHT SIDE OF THE ROAD, ONTO THE SHOULDER. THE TRUCK THEN SPUTTERED AND STALLED. I DID NOT ATTEMPT TO RESTART OR MOVE THE VEHICLE, INSTEAD WORKED WITH THE DEALERSHIP TO OBTAIN A TOW TRUCK.
TRUCK STARTED MAKING VERY STRANGE NOISE,, CAME HOME LET TRUCK SIT, WENT TO RESTART AND ENGINE LIGHT CAME ON, TRUCK MADE VERY HORRIBLE SOUND, AND STARTED SPITTING OIL OUT OF THE SIDE OF THE BLOCK. HOLE IN BLOCK AND AT LEAST ONE PISTON DESTROYED.
Official recalls
1026V083000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Feb 12, 2026
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence & remedy
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
Power Train:automatic Transmission:control Module:software
General Motors, LLC is recalling certain 2020 Chevrolet Silverado 2500, 3500, GMC Sierra 2500, 3500, and 2020-2022 Chevrolet Silverado 1500 and GMC Sierra 1500 vehicles that may have been repaired incorrectly under recall 24V797. The transmission control valve may fail and cause the rear wheels to lock up.
Consequence: Rear wheel lock up increases the risk of a crash.
Remedy: Dealers will inspect the vehicles and update the transmission control software, free of charge. Owner notification letters were mailed March 6, 2026. Owners may contact GMC customer service at 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N252516560. Vehicle Identification Numbers (VINs) involved in this recall became searchable on NHTSA.gov on February 12, 2026.
24V797000 · Power Train:automatic Transmission:control Module:software; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
Oct 24, 2024
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence & remedy
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Additional source detail variants (2)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
Power Train:automatic Transmission:control Module:software
General Motors, LLC (GM) is recalling certain 2020-2022 Chevrolet Silverado 1500, 2500, 3500, GMC Sierra 1500, 2500, 3500, 2021 Cadillac Escalade, Escalade ESV, Chevrolet Tahoe, Suburban, GMC Yukon, and Yukon XL vehicles equipped with diesel engines. The transmission control valve may fail and cause the rear wheels to lock-up.
Consequence: Rear wheel lock-up can increase the risk of a crash.
Remedy: Dealers will install new transmission control module software, free of charge. GM will provide a special coverage program to cover the repair of transmissions that are identified by the remedy software as containing a defective control valve. Owner notification letters were mailed December 12, 2024. Owners may contact GM customer service at 1-888-988-7267, Cadillac customer service at 1-800-458-8006, GMC customer service at GMC 1-800-462-8782 or Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N242454440.
24V060000 · Latches/locks/linkages:tailgate:latch
Feb 1, 2024
General Motors, LLC (GM) is recalling certain 2020-2024 Chevrolet Silverado 2500, 3500, GMC Sierra 2500 and 3500 vehicles equipped with power-unlatching tailgates. The tailgate's electronic gate-release switch may short circuit due to water intrusion, which can result in the tailgate inadvertently unlatching while the vehicle is in park.
Consequence & remedy
Consequence: An unlatched tailgate may open while driving and result in a loss of unsecured cargo, creating a road hazard and increasing the risk of a crash.
Remedy: Owners are advised to check that the tailgate is closed and latched before driving. Dealers will replace the exterior touchpad switch assemblies, free of charge. Owner notification letters were mailed May 17, 2024. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is N232426400.
21V578000 · Tires:temporary/emergency Spare Tire
Jul 29, 2021
General Motors, LLC. (GM) is recalling certain 2020-2021 Chevrolet Silverado 2500 and GMC Sierra 2500 vehicles equipped with a 17" spare tire (RPO ZHQ or ZXT) and either the 20" accessory road tire (RPO REM) or the 18" accessory road tire (RPO Q2V). Operating the spare tire with other 20" or 18" tires can prevent the Anti-Lock Braking System (ABS) from engaging.
Consequence & remedy
Consequence: An ABS system that cannot control the rear wheels independently increases the risk of a crash.
Remedy: Dealers will provide the appropriate spare tire and apply a new spare tire information label, free of charge. Owner notification letters were mailed on October 18, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; GMC customer service at 1-800-462-8782. GM's number for this recall is N212329780.
20V792000 · Seat Belts; Seat Belts:critical Fasteners
Dec 17, 2020
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence & remedy
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Additional source detail variants (2)
Seat Belts:critical Fasteners
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
Seat Belts
General Motors, LLC (GM) is recalling certain 2019-2021 Chevrolet Silverado 1500 and GMC Sierra 1500, 2021 Chevrolet Suburban and Tahoe and GMC Yukon XL and 2020-2021 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The seat belt brackets may not be secured to the seat frame in the front-row center seating position.
Consequence: If a seat-belt bracket is not secured, the seat belt may not properly restrain an occupant in the front-row center seat position, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will inspect left-side and right-side front-row center seat-belt bracket attachments and reassemble it correctly as necessary, free of charge. The recall began January 26, 2021. Owners may contact GMC customer service at 1-800-462-8782, Chevrolet customer service at 1-800-222-1020. GM's number for this recall is N202314670.
20V650000 · Power Train:driveline:driveshaft
Oct 22, 2020
General Motors LLC (GM) is recalling certain 2019-2020 Chevrolet Silverado 1500 and GMC Sierra 1500 and 2020 Chevrolet Silverado 2500 trucks. One of the driveshaft joints may not have been properly welded, causing the driveshaft to separate while the vehicle is moving.
Consequence & remedy
Consequence: If the driveshaft separates, there may be a loss of propulsion, increasing the risk of crash.
Remedy: GM will notify owners, and dealers will replace the driveshaft, free of charge. The recall is expected to begin December 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202314870.
20V446000 · Air Bags:side/window:curtain:inflator
Jul 30, 2020
General Motors, LLC. (GM) is recalling certain 2020 Buick Enclave, Cadillac XT5 and XT6, Chevrolet Blazer, Silverado 1500, 2500 and 3500 and Traverse and GMC Acadia and Sierra 1500, 2500 and 3500 vehicles. The diffuser component of the Roof-Rail Air Bag (RRAB) inflator may not have been properly crimped to the inflator and could separate from the inflator during air bag deployment.
Consequence & remedy
Consequence: If the diffuser separates from the inflator during deployment, RRAB performance may be degraded, increasing the risk of injury in a crash.
Remedy: GM will notify owners, and dealers will replace the suspect RRAB modules, free of charge. The recall began September 3, 2020. Owners may contact Chevrolet customer service at 1-800-630-2438, Cadillac customer service at 1-800-333-4223, or Buick customer service at 1-800-521-7300. GM's number for this recall is N202305380.
20V324000 · Latches/locks/linkages:hood:latch; Structure:body:hood
Jun 4, 2020
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence & remedy
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
Additional source detail variants (2)
Latches/locks/linkages:hood:latch
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
Structure:body:hood
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles previously recalled under 20V-142. Some of the vehicles in 20V-324 were not part of Recall 20V-142 but received defect parts during another service (typically during collision repair). The hood-latch striker wires on replacement hoods installed for Safety Recall 20V-142 may not have been heat-treated properly, possibly causing them to fracture.
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. For hoods sold over the counter, dealers will contact customers with instructions for hood replacement. The recall began July 7, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N202306490.
20V142000 · Latches/locks/linkages:hood:latch
Mar 12, 2020
General Motors LLC (GM) is recalling certain 2020 Chevrolet Silverado 2500 and 3500 and GMC Sierra 2500 and 3500 vehicles. The hood-latch striker wires may not have been heat-treated properly, possibly causing them to fracture.
Consequence & remedy
Consequence: If a striker wire fractures, the hood may open unexpectedly while driving, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the hood assembly, free of charge. The recall began April 13, 2020. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N192284960.
19V814000 · Seat Belts:pretensioner
Nov 14, 2019
General Motors LLC (GM) is recalling certain 2019-2020 Chevrolet Silverado 1500 and GMC Sierra 1500, and 2020 Silverado 2500, Silverado 3500, Sierra 2500, and Sierra 3500 vehicles equipped with carpet floor covering. When the front seat belt pretensioners deploy, hot gas may vent through an opening in the pretensioner bracket, possibly igniting the carpet.
Consequence & remedy
Consequence: A vehicle fire could result if materials ignite inside the vehicle.
Remedy: GM will notify owners, and dealers will close off the opening in the pretensioner bracket, free of charge. The recall began December 13, 2019. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-888-988-7267. GM's number for this recall is N192270600.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE21010 · Air Bag Malfunction
Opened Apr 9, 2021 · Closed Aug 24, 2023
Status: closed (inferred from source dates) · Air Bags; Air Bags:frontal; Air Bags:frontal:driver Side:inflator Module; Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Additional source detail variants (4)
Air Bags:frontal:driver Side:inflator Module
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:frontal
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.
Air Bags:srs Malfunction Warning Lamp/light
On April 9, 2021, the Office of Defects Investigations (ODI) opened PE21-010 to investigate instances of air bag malfunction indicator light (MIL) illumination and potential for frontal air bag non-deployment in several vehicles manufactured by General Motors (GM). The vehicles included model year (MY) 2020 through 2021 CT4 and CT5 passenger cars, Sierra and Silverado trucks (1500/2500/3500 models), XT4 and MY 2021 Escalade, Suburban, Tahoe, Yukon SUVs.Technical Service Bulletin (TSB) 21-NA-005, issued in March 2021, addresses air bag MIL illumination with diagnostic trouble codes (DTCs) B0001-1B or B0012-0D. It cites rust particles in the connection terminal interface of the driver air bag inflator housing as the cause of the air bag MIL illumination. Illumination of the air bag MIL under these circumstances may result in a non-deployment of the frontal driver air bag during a frontal collision and increased risk of injury to the driver.GM stated a correlation exists between production delays due to the pandemic shutdown and premature corrosion initiation on the surface of the air bag inflator housing, which, in some cases, caused rust development during a seven (7) month period of vehicle production. In the rare instance when a rust particle dislodges from the driver air bag inflator housing and enters the air bag connector prior to assembly, an intermittent resistance spike at the air bag connector may result. The condition generates excessive resistance in the air bag electrical system when the steering wheel horn cover is manipulated or the steering wheel is turned. This excessive resistance is momentary. A crash commanding air bag deployment would need to occur exactly when the momentary excessive resistance occurs. Thus, there is a very low likelihood the hazard will present a risk during a crash of sufficient severity to warrant a commanded deployment. This failure mechanism occurs early in life and results in an air bag MIL illumination that corresponds to a DTC warning the driver that the vehicle requires service. The vehicle's air bag remains functional while the MIL is illuminated, and the DTC is present.Once the connection of the driver air bag module to the clockspring is made at the plant, or at the dealership for service, there is no longer an opportunity for rust migration into the connection point. The connector is sealed and has gold terminals, eliminating the expectation of fretting corrosion. All subject vehicles passed standard corrosion validation testing for extensive corrosion with no issue of air bag non-deployment.There is a low rate of occurrence: 1.41 incidents per thousand vehicles (IPTV) for all related occurrences, and 0.04 IPTV for occurrences with a mention of visible rust and/or corrosion on the air bag inflator housing. The average occurrence mileage for the subject vehicles is approximately 2,100. Every occurrence related to the alleged defect experienced an air bag MIL illumination and there are no verified allegations of air bag non-deployment within all data sources.To date, there have been no reported fires, crashes, injuries, or fatalities related to this issue. In view of the low rate, and the nature of early-life failure, the high detectability of failures, and low potential hazard to drivers, this Preliminary Evaluation (PE) is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The agency reserves the right to take additional action if warranted by new circumstances.Review the ODI reports cited above at nhtsa.gov under the following identification numbers: 11537927, 11528888, 11525020, 11521401, 11506057, 11493107, 11486767, 11441525, 11433146, 11425658, 11423440, 11385267, 11376429, 11373466, 11366995.