IllustrationWENT TO THE STORE AND SAW MY DASH HAD A CRACK IN IT. IT WAS IN MY DRIVEWAY LOCKED. NOBODY HAD ACCESS TO IT.
2009 Chevrolet Silverado 2500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2009 Chevrolet Silverado 2500 do not stand out strongly from the model-year median of 81.
About this comparison →How this year compares
Owner complaints by model year
Compare all Silverado 2500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
110–25K
525–50K
850–75K
575–100K
8100–150K
4150K+
41 reports with mileage · 20 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 24 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 6 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
6 crash reports3 fire reports5 injury reports
Structure complaints
6 reportsDASH AROUND THE AIR BAG AND IN FRONT OF INSTRUMENT CLUSTER STARTED CRACKING SHORTLY AFTER WARRANTEE WAS OUT. I CONTACTED CHEVROLET AND THEY SAID IT WAS BECAUSE OF THE SUN. I TOLD THEM I BOUGHT IT IN FLORIDA AND I'M SURE THE SUN DOESN'T SHINE THERE. WHAT AM I SUPPOSE TO DO KEEP IT IN THE GARAGE AND NEVER TAKE IT OUT. THEY OFFER M…
Read full complaint
DASH AROUND THE AIR BAG AND IN FRONT OF INSTRUMENT CLUSTER STARTED CRACKING SHORTLY AFTER WARRANTEE WAS OUT. I CONTACTED CHEVROLET AND THEY SAID IT WAS BECAUSE OF THE SUN. I TOLD THEM I BOUGHT IT IN FLORIDA AND I'M SURE THE SUN DOESN'T SHINE THERE. WHAT AM I SUPPOSE TO DO KEEP IT IN THE GARAGE AND NEVER TAKE IT OUT. THEY OFFER ME 100.00 TOWARDS THE REPAIR. THAT WAS AN INSULT TO A CLEAR MANUFACTURES DEFECT. THE PLASTIC UPON A COLLISION COULD BECOME A FLYING PROJECTILE THAT COULD CAUSE SERIOUS INJURY.
THE CHROME PLATING IS PEELING OFF THE DRIVERS INTERIOR DOOR HANDLE THAT HAS CREATED A SHARP SURFACE AND HAS ALREADY CUT MY WIFE'S HAND. UPON RESEARCHING THE ISSUE FURTHER IT WAS FOUND THERE IS A SERVICE BULLETIN DIRECTLY RELATED TO THIS EXACT ISSUE. THE PROBLEM IS THE BULLETIN IS ONLY REFERENCING 2007 MODEL YEAR'S SPECIFICAL…
Read full complaint
THE CHROME PLATING IS PEELING OFF THE DRIVERS INTERIOR DOOR HANDLE THAT HAS CREATED A SHARP SURFACE AND HAS ALREADY CUT MY WIFE'S HAND. UPON RESEARCHING THE ISSUE FURTHER IT WAS FOUND THERE IS A SERVICE BULLETIN DIRECTLY RELATED TO THIS EXACT ISSUE. THE PROBLEM IS THE BULLETIN IS ONLY REFERENCING 2007 MODEL YEAR'S SPECIFICALLY. THE BULLETIN WAS RELEASED IN JULY/AUGUST OF 2010 SO MANY YEARS FROM 2007 ' 2009 WERE AFFECTED BY THIS DEFECT. IN THE DOCUMENT PAGE 51 OF 86 SPECIFICALLY MENTIONS MODEL YEAR 2007 ' 2009 CHEVROLET SILVERADO AND GMC SIERRA AND DENALI TRUCKS EQUIPPED WITH RPOS AN3, Y91, OR GAT. MY TRUCK HAS RPO CODE AN3 AND THE HANDLE IS PEELING. I HAVE ALREADY CONTACTED CHEVY CUSTOMER CARE AND INQUIRED ABOUT THIS DEFECT BUT THEY ARE NOT WILLING TO ADMIT TO OR REPAIR THE DEFECT FREE OF COST AS PER THIS BULLETINS EXTENDED COVERAGE OF 10 YEARS OR 100,000 MILES. I AM REPORTING THIS CASE IN HOPES THAT YOU CAN HELP MY SITUATION OR PROVIDE SOME FEEDBACK ON HOW I CAN GET THIS RESOLVED. EA10-004 GM 8-16-2010 #09239 SERVICE BULLETIN
THE DASH HAS CRACKED IN TWO PLACES. ONE OF THEM IS LOCATED AT THE AIR BAG.
THE DASH IS CRACKING IN 2 SPOTS. THIS SEEMS TO BE A SAFETY HAZARD DURING AN ACCIDENT AND WHEN THE AIRBAG IS DEPLOYED.
I PURCHASED SOME AFTER-MARKET NERF/STEP BARS TO FIT MY NEW 2009 CHEVROLET SILVERADO 2500HD CREW CAB PICKUP. THE STEPS WERE INSTALLED ON FRIDAY 06/04/2010 ACCORDING TO THE MANUFACTURERS INSTRUCTIONS. THE STEPS WERE MADE BY DEE ZEE INC. OF DES MOINES, IA AND THE MODEL NUMBER OF THE PRODUCT IS 17053C. ON 06/06/2010 AT APPROXIMAT…
Read full complaint
I PURCHASED SOME AFTER-MARKET NERF/STEP BARS TO FIT MY NEW 2009 CHEVROLET SILVERADO 2500HD CREW CAB PICKUP. THE STEPS WERE INSTALLED ON FRIDAY 06/04/2010 ACCORDING TO THE MANUFACTURERS INSTRUCTIONS. THE STEPS WERE MADE BY DEE ZEE INC. OF DES MOINES, IA AND THE MODEL NUMBER OF THE PRODUCT IS 17053C. ON 06/06/2010 AT APPROXIMATELY 2230 HOURS, MY WIFE WAS PLACING A TWO YEAR OLD CHILD INTO HER CHILD SAFETY SEAT WHILE STANDING ON THE PLASTIC STEP AREA OF THE STEP BAR. THE PLASTIC STEP AREA BROKE FROM THE METAL STEP BAR, CAUSING MY WIFE TO FALL TO THE GROUND. ON HER WAY TO THE GROUND, BOTH OF MY WIFE'S UPPER SHINS OF HER LEGS STRUCK THE TRUCK FLOOR AND THE STEP BARS, CAUSING A LARGE AMOUNT OF BRUISING TO HER LEGS. I REMOVED THE STEP BARS THE NEXT DAY AND HAVE CONTACTED THE RETAILER FOR A RETURN AND REFUND OF THE PRODUCT. *TR
Official recalls
521V050000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2007-2011 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL, and 2009-2011 Chevrolet Silverado 2500, Silverado 3500, GMC Sierra 2500 and Sierra 3500 vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 22, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on March 1, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328760.
21V052000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2009 Cadillac Escalade, Escalade ESV, Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2007-2008 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Suburban, Tahoe, GMC Sierra 1500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 23, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on September 20, 2021. Owners may contact Chevrolet customer service at 1-800-222-1020, Cadillac customer service at 1-800-458-8006, and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328780.
21V053000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2013 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Additionally, GM is recalling certain 2010 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Additionally, GM is recalling certain 2009 Cadillac Escalade, Escalade ESV, and Escalade EXT, Chevrolet Avalanche, Silverado 1500, Silverado 2500/3500, Suburban, Tahoe, GMC Sierra 1500, Sierra 2500/3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C."
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 24, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed on May 11, 2021. Owners may contact Cadillac customer service at 1-800-458-8006; Chevrolet customer service at 1-800-222-1020; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328790.
18V267000 · Equipment
Apr 26, 2018
General Motors LLC (GM) is recalling certain 2009-2014 Chevrolet Silverado HD and GMC Sierra HD, 2009 GMC Topkick 5000, 6000, 7000 and 8000 Series and Isuzu F Series, and 2009-2018 Chevrolet Express, and GMC Savana vehicles, equipped with certain Plastic-Handle Fire Extinguishers or Push Button 'Pindicator' Fire Extinguishers. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: In the event of a fire, if the fire extinguisher does not function properly, it can increase the risk of injury.
Remedy: GM will notify owners, instructing them to contact Kidde to get a replacement fire extinguisher, free of charge. The recall began June 11, 2018. Owners may contact Chevrolet customer service at 1-800-222-1020, GMC customer service at 1-800-462-8782, and Isuzu customer service at 1-866-441-9638. GM's number for this recall is 18146.
14V407000 · Electrical System
Jul 2, 2014
General Motors LLC (GM) is recalling certain model year 2007-2011 Chevrolet Silverado HD 2500/3500 trucks manufactured January 18, 2007, to June 22, 2011, and GMC Sierra HD 2500/3500 trucks manufactured January 22, 2007, to June 21, 2011, and equipped with an auxiliary battery. Owners may unknowingly draw too much current through the vehicle's trailer harness resulting in the melting of fusible link for the auxiliary battery.
Consequence & remedy
Consequence: If the fusible link melts it may come into contact with adjacent components, damage the electrical center cover, the nearby wiring harness conduit and other vehicle components, increasing the risk of a fire.
Remedy: GM will notify owners and dealers will replace the jumper harness with one that includes a 40 amp inline fuse, and provide the owner with supplemental Owner Manual information, free of charge. The recall began on August 29, 2014. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GM's number for this recall is 14260.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.