IllustrationTransmission problem Reduce Power, unintended deceleration and unintended deceleration with the reverse or complete stop.
2022 Chevrolet Express Cutaway Van
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Express Cutaway Van years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 0 of 3 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
3 reportsTransmission problem Reduce Power, unintended deceleration and unintended deceleration with the reverse or complete stop.
Transmission problem Reduce Power, unintended deceleration and unintended deceleration with the reverse or complete stop.
Official recalls
123V247000 · Electrical System:wiring
Apr 6, 2023
General Motors, LLC (GM) is recalling certain 2003-2023 Chevrolet Express Cutaway and GMC Savana Cutaway incomplete vehicles equipped with wiring for an optional rear heating, ventilation, and air-conditioning (HVAC) system. When the HVAC blower motor circuit is left unused with exposed connectors and wiring, the circuit can corrode and overheat.
Consequence & remedy
Consequence: An overheated electrical circuit increases the risk of a fire.
Remedy: Dealers will properly seal the rear HVAC blower motor circuits at the left side B-pillar, free of charge. Owner notification letters were mailed May 2, 2023. Owners may contact Chevrolet customer service at 1-800-222-1020 or GMC customer service at 1-800-462-8782. GMC's number for this recall is N222386050.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE23016 · 6L90 Transmission Failure
Opened Sep 27, 2023 · Closed Jan 10, 2025
Status: closed (inferred from source dates) · Power Train; Power Train:automatic Transmission; Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE) after receiving one Vehicle Owner Questionnaire (VOQ) complaint related to four school buses built on General Motors (GM) van chassis. The VOQ alleged transmission failure resulting in a loss of all forward gear. In ODI's pre-investigative discussions with GM, ODI learned that valve body separator plates had been machined out of tolerance during production periods between October 2016 to April 2017 and February 2021 to April 2021. This out of tolerance machining may create excessive wear to the valve body check balls, possibly resulting in an inability to engage drive or reverse. The potential loss of drivability only begins when shifting from a park or neutral transmission selection and does not occur during a functional drive cycle. The average failure mileage of vehicles which experienced this condition is within warranty and related claims or complaints did not include any accidents, injuries, or fatalities. After discussions with GM, Technical Service Bulletin (TSB) 23-NA-142 (NHTSA ID number 10243753) was released in September 2023. This technical service bulletin provides a procedure for technicians to replace the forward check ball and separator plate if found to be the cause of a customer's concern. During the course of the investigation, GM also released a Customer Satisfaction Program (CSP) N232428780 (NHTSA ID 10253316) in February 2024, to notify school bus and ambulance fleets of the concern and to proactively mitigate the risk in these essential-operation vehicles. Recently, ODI contacted multiple school bus fleets, verifying that there have not been any stranded buses mid-route from this condition. Additionally, ODI has not received any additional VOQ complaints since the opening of this investigation. Based on the available information, including GM's TSB and CSP, this PE is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI report cited in the Closing Resume ODI Report Identification Numbers document, go to NHTSA.gov.
Additional source detail variants (3)
Power Train:automatic Transmission:fluid/lubricant:valves/valve Body
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE) after receiving one Vehicle Owner Questionnaire (VOQ) complaint related to four school buses built on General Motors (GM) van chassis. The VOQ alleged transmission failure resulting in a loss of all forward gear. In ODI's pre-investigative discussions with GM, ODI learned that valve body separator plates had been machined out of tolerance during production periods between October 2016 to April 2017 and February 2021 to April 2021. This out of tolerance machining may create excessive wear to the valve body check balls, possibly resulting in an inability to engage drive or reverse. The potential loss of drivability only begins when shifting from a park or neutral transmission selection and does not occur during a functional drive cycle. The average failure mileage of vehicles which experienced this condition is within warranty and related claims or complaints did not include any accidents, injuries, or fatalities. After discussions with GM, Technical Service Bulletin (TSB) 23-NA-142 (NHTSA ID number 10243753) was released in September 2023. This technical service bulletin provides a procedure for technicians to replace the forward check ball and separator plate if found to be the cause of a customer's concern. During the course of the investigation, GM also released a Customer Satisfaction Program (CSP) N232428780 (NHTSA ID 10253316) in February 2024, to notify school bus and ambulance fleets of the concern and to proactively mitigate the risk in these essential-operation vehicles. Recently, ODI contacted multiple school bus fleets, verifying that there have not been any stranded buses mid-route from this condition. Additionally, ODI has not received any additional VOQ complaints since the opening of this investigation. Based on the available information, including GM's TSB and CSP, this PE is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI report cited in the Closing Resume ODI Report Identification Numbers document, go to NHTSA.gov.
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE) after receiving one Vehicle Owner Questionnaire (VOQ) complaint related to four school buses built on General Motors (GM) van chassis. The VOQ alleged transmission failure resulting in a loss of all forward gear. In ODI's pre-investigative discussions with GM, ODI learned that valve body separator plates had been machined out of tolerance during production periods between October 2016 to April 2017 and February 2021 to April 2021. This out of tolerance machining may create excessive wear to the valve body check balls, possibly resulting in an inability to engage drive or reverse. The potential loss of drivability only begins when shifting from a park or neutral transmission selection and does not occur during a functional drive cycle. The average failure mileage of vehicles which experienced this condition is within warranty and related claims or complaints did not include any accidents, injuries, or fatalities. After discussions with GM, Technical Service Bulletin (TSB) 23-NA-142 (NHTSA ID number 10243753) was released in September 2023. This technical service bulletin provides a procedure for technicians to replace the forward check ball and separator plate if found to be the cause of a customer's concern. During the course of the investigation, GM also released a Customer Satisfaction Program (CSP) N232428780 (NHTSA ID 10253316) in February 2024, to notify school bus and ambulance fleets of the concern and to proactively mitigate the risk in these essential-operation vehicles. Recently, ODI contacted multiple school bus fleets, verifying that there have not been any stranded buses mid-route from this condition. Additionally, ODI has not received any additional VOQ complaints since the opening of this investigation. Based on the available information, including GM's TSB and CSP, this PE is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI report cited in the Closing Resume ODI Report Identification Numbers document, go to NHTSA.gov.
Power Train
The Office of Defects Investigation (ODI) opened this Preliminary Evaluation (PE) after receiving one Vehicle Owner Questionnaire (VOQ) complaint related to four school buses built on General Motors (GM) van chassis. The VOQ alleged transmission failure resulting in a loss of all forward gear. In ODI's pre-investigative discussions with GM, ODI learned that valve body separator plates had been machined out of tolerance during production periods between October 2016 to April 2017 and February 2021 to April 2021. This out of tolerance machining may create excessive wear to the valve body check balls, possibly resulting in an inability to engage drive or reverse. The potential loss of drivability only begins when shifting from a park or neutral transmission selection and does not occur during a functional drive cycle. The average failure mileage of vehicles which experienced this condition is within warranty and related claims or complaints did not include any accidents, injuries, or fatalities. After discussions with GM, Technical Service Bulletin (TSB) 23-NA-142 (NHTSA ID number 10243753) was released in September 2023. This technical service bulletin provides a procedure for technicians to replace the forward check ball and separator plate if found to be the cause of a customer's concern. During the course of the investigation, GM also released a Customer Satisfaction Program (CSP) N232428780 (NHTSA ID 10253316) in February 2024, to notify school bus and ambulance fleets of the concern and to proactively mitigate the risk in these essential-operation vehicles. Recently, ODI contacted multiple school bus fleets, verifying that there have not been any stranded buses mid-route from this condition. Additionally, ODI has not received any additional VOQ complaints since the opening of this investigation. Based on the available information, including GM's TSB and CSP, this PE is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances. To review the ODI report cited in the Closing Resume ODI Report Identification Numbers document, go to NHTSA.gov.