Failed the inspection in texas. No details.
2014 Cadillac Escalade
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2014 Cadillac Escalade do not stand out strongly from the model-year median of 47.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Escalade years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 10 of 20 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 8 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Air Bags. Review the 5 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
20 reportsWhile driving my 2016 Cadillac Escalade with a6.2L V8 engine on [XXX] near Bristow, Oklahoma at approximately 75 mph, the vehicle suddenly and completely lost power. Without any prior warning or unusual noises, the engine shut down, and I lost power to the dashboard and power steering. This caused the vehicle to decelerate rapi…
Read full complaint
While driving my 2016 Cadillac Escalade with a6.2L V8 engine on [XXX] near Bristow, Oklahoma at approximately 75 mph, the vehicle suddenly and completely lost power. Without any prior warning or unusual noises, the engine shut down, and I lost power to the dashboard and power steering. This caused the vehicle to decelerate rapidly, making it extremely difficult to control. I managed to steer the vehicle to the shoulder of the highway, narrowly avoiding a collision due to the loss of control. The vehicle could not be restarted. The affected components seem to include the engine, electrical system, and steering. These failures put my safety and the safety of others at significant risk due to the sudden and unexpected loss of vehicle control on a busy highway. The vehicle was towed to the nearest Cadillac dealership for inspection and repair. As of now, the dealership has been unable to determine the cause of the engine failure despite conducting multiple tests and inspections. There were no warning lamps, messages, or other symptoms prior to the failure. The dealership has confirmed the issue but has not identified the root cause. The vehicle remains at the dealership for further diagnostics and is available for inspection upon request. INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6)
The contact owns a 2014 Cadillac Escalade. The contact stated that after going through the car wash, the passenger’s side mirror became inoperable. There were no warning lights illuminated. The contact was unable to reset the mirror like stated in the Owner’s Manual. The contact called the local dealer, but the vehicle was not d…
Read full complaint
The contact owns a 2014 Cadillac Escalade. The contact stated that after going through the car wash, the passenger’s side mirror became inoperable. There were no warning lights illuminated. The contact was unable to reset the mirror like stated in the Owner’s Manual. The contact called the local dealer, but the vehicle was not diagnosed or repaired. The contact called the manufacturer, who referred him to the local dealer for assistance. The approximate failure mileage was 40,000.
I am having an electrical short that is shutting down everything while I'm driving or stopped, it makes driving it Dangerous and Scary. It looks like the recall from 2014 that describes everything I'm experiencing. Recall 14515 that talks about a Chassis Control Module that controls a lot of things including the fuel pump and …
Read full complaint
I am having an electrical short that is shutting down everything while I'm driving or stopped, it makes driving it Dangerous and Scary. It looks like the recall from 2014 that describes everything I'm experiencing. Recall 14515 that talks about a Chassis Control Module that controls a lot of things including the fuel pump and more electrical components to list. I have a vehicle that is Dangerous to drive, im a Disabled Veteran and am tied to a Powered Chair. I have called Cadillac and they say that my Escalade is not included and they will do nothing for me. I'm at a lose as what to do, I could just sell it to someone else and let them deal with it or get killed in it. Either way is not a good choice. Let me know what you would do if you were in my position.
2014 CADILLAC ESCALADE. CONSUMER WRITES IN REGARD TO FRONTAL AIRBAG INFLATOR SAFETY RECALL. THE CONSUMER STATED THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME COMPLETING THE RECALL REPAIR. THE CONSUMER WAS INFORMED THE PARTS WERE UNAVAILABLE.
Cadillac sent a notice of the recall. The authorized Chevrolet dealership repair facility and Cadillac told me that they would not accept the risk that the dashboard would not crack in installation of authorized Chevrolet dealership repair facility defective part and that 'I' would have to sign a waiver saying 'I' accept the ris…
Read full complaint
Cadillac sent a notice of the recall. The authorized Chevrolet dealership repair facility and Cadillac told me that they would not accept the risk that the dashboard would not crack in installation of authorized Chevrolet dealership repair facility defective part and that 'I' would have to sign a waiver saying 'I' accept the risk that they 'could' damage my car and would be 'my' responsibility if the dash is ruined and pay for the replacement. This is not my error/defective issue, but GM's. They have already indicated that people have been injured and died from this defective part. I believe Cadillac should accept the 'potential' risk should it be damaged. I am getting no where with Cadillac and would like to have the NHTSA to weigh in on their lack of support to mitigate this error. Certainly hoping that the dash does not crack, but I don't have the funds to take on that risk and they've left me in bad situation with a KNOWN risk of defective part.
The contact owns a 2014 Cadillac Escalade. The contact stated while driving at various speeds, the vehicle would drive rough. The vehicle was taken to an independent mechanic where it was diagnosed with needing the struts and shocks replaced. The vehicle was repaired. The manufacturer was informed of the failure and told the con…
Read full complaint
The contact owns a 2014 Cadillac Escalade. The contact stated while driving at various speeds, the vehicle would drive rough. The vehicle was taken to an independent mechanic where it was diagnosed with needing the struts and shocks replaced. The vehicle was repaired. The manufacturer was informed of the failure and told the contact that the VIN was not included in a recall regarding the failure. The failure mileage was approximately 41,000. Vehicle has been repaired.
On Saturday June 26, 2021 I open the driver door to the vehicle and the passenger seat caught. on fire and burned a hole in the side of the seat .
RADIATOR LEAK DISCOVERED. PROBLEM WITH CYCLING OF THE THERMOSTAT THAT CAUSES STRESS FRACTURES ON THE RADIATOR LEADING TO COOLANT LEAKS. GM BULLETINS ON THE 2014 AND 2015 MODELS. P11513A AND P11513F. THIS WAS LEAKING FOR A WHILE AND WAS NOT NOTICED UNTIL MULTI POINT INSPECTION I REQUESTED BY THE SERVICE CENTER I US…
Read full complaint
RADIATOR LEAK DISCOVERED. PROBLEM WITH CYCLING OF THE THERMOSTAT THAT CAUSES STRESS FRACTURES ON THE RADIATOR LEADING TO COOLANT LEAKS. GM BULLETINS ON THE 2014 AND 2015 MODELS. P11513A AND P11513F. THIS WAS LEAKING FOR A WHILE AND WAS NOT NOTICED UNTIL MULTI POINT INSPECTION I REQUESTED BY THE SERVICE CENTER I USE FOR SERVICE. (B&B SERVICE CENTER, FARMINGTON NH. THIS WAS A KNOW ISSUE ON THIS MODEL VEHICLE.
INFORMATION RELEASED BY NBC.
Official recalls
221V054000 · Air Bags:frontal:passenger Side:inflator Module
Feb 5, 2021
General Motors, LLC (GM) is recalling certain 2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL vehicles originally sold, or ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP, and VI or "Zone A." Additionally GM is recalling certain 2011-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, Yukon XL and 2011-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Additionally, GM is recalling certain 2010-2014 Cadillac Escalade, Escalade ESV, Chevrolet Silverado 2500, Silverado 3500, Suburban, Tahoe, GMC Sierra 2500, Sierra 3500, Yukon, and Yukon XL and 2010-2013 Cadillac Escalade EXT, Chevrolet Avalanche, Silverado 1500, and GMC Sierra 1500 vehicles originally sold, or ever registered, in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with non-desiccated passenger frontal inflators containing phase-stabilized ammonium nitrate (PSAN) propellant. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants, resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the front passenger air bag inflator with an alternate one, free of charge. Interim letters notifying owners of the safety risk were mailed on February 25, 2021. Second notification letters will be mailed once the remedy is available. Owner notification letters were mailed to 40 VIN owners on May 11, 2021. A second owner notification letter was mailed to all other owners on January 24, 2022. Owners may contact Chevrolet customer service at 1-800-222-1020; Cadillac customer service at 1-800-458-8006; and GMC customer service at 1-800-462-8782. GM's number for this recall is N212328800.
14V614000 · Electrical System
Oct 1, 2014
General Motors LLC (GM) is recalling certain model year 2013-2014 Cadillac CTS, Escalade, Escalade ESV, Chevrolet Suburban, Tahoe, GMC Yukon, and Yukon XL, and 2014 Buick Enclave, Chevrolet Express, Impala, Silverado HD, Traverse, GMC Acadia, Savana, and Sierra HD vehicles. In the affected vehicles, the chassis electronic module may be internally contaminated, resulting in an electrical short.
Consequence & remedy
Consequence: If the module experiences an electrical short, the vehicle could stall, increasing the risk of a crash.
Remedy: GM will notify owners, and dealers will replace the chassis electronic module, free of charge. The recall began on December 26, 2014. Owners may contact GM customer service at 1-800-521-7300 (Buick), 1-800-458-006 (Cadillac), 1-800-222-1020 (Chevrolet), and 1-800-462-8782 (GMC). GMs number for this recall is 14515.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration