Electrical System. Review the 14 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Engine. Review the 11 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Fuel/propulsion System. Review the 11 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

2 crash reports1 fire reports1 injury reports

Suspension complaints

6 reports

Clear category filter

Mileage unknown · May 22, 2026

StructureSuspension

The attaching nut and bolt holding the left suspension to the rear subframe worked itself lose. The nut had completely fallen off. The corresponding bolt was merely hanging on but was about to fall off too. The vehicle was behaving weirdly and unstable even at slower speeds.

NHTSA ODI #11739474

Mileage unknown · Apr 16, 2026

Suspension

Read full complaint

I experienced a complete failure of the rear pneumatic (air) suspension system on my vehicle. This system uses rubber air springs (“airbags”) rather than conventional coil springs. When it failed, the rear of the vehicle dropped significantly, causing metal-to-metal contact, an extreme upward pitch of the front end, and pronounced instability. The vehicle became difficult to control, with excessive rear sway creating an unsafe driving condition. Based on my experience and publicly available information, this appears to be a known and recurring issue affecting BMW X5 and X6 models (E70, F15, and G05). The failure is commonly attributed to degradation of the rubber air springs, which can dry out, crack, or leak. When leaks develop, the compressor runs excessively and may fail, resulting in sudden loss of suspension support. While these components may be considered wear items, the frequency and relatively early occurrence of these failures suggest a design or engineering vulnerability rather than typical maintenance. Failures are widely reported between approximately 50,000 and 100,000 miles or within 4–7 years, indicating a pattern of premature degradation. This condition can occur without clear warning, including after the vehicle has been parked, meaning drivers may not recognize the issue until the vehicle is unsafe to operate. Once the system fails, handling is severely compromised, increasing the risk of loss of control. Repair costs often exceed $5,000, which may discourage timely repairs and leave vehicles in unsafe condition. BMW characterized this as a maintenance issue despite the apparent pattern. I am submitting this complaint because this condition poses a serious safety risk. A sudden loss of rear suspension support at speed could result in loss of control, increasing the risk of a crash, injury, or fatality.

NHTSA ODI #11731591

Mileage unknown · Nov 3, 2023

Suspension

Read full complaint

So I test drove a BMW X5 e drive a couple months ago at an independent used car dealer and it looked perfect but when I drove it the car bounced excessively over any minor bump in the road. It felt like sitting in the back seats in a school bus not like driving a luxury SUV. They offered to fix it but I just felt like I couldn't trust them after this experience. I chalked this experience up to a used car dealership just trying to pass off a car to someone who might not notice the suspension being broken. So I've been searching for a couple months to find the perfect one at a bigger more trustworthy car dealer. I ordered one online at carmax and had this car delivered Friday and my husband/I hopped inside to grab some lunch and take it for a spin only to realize this second 2018 BMW X5 hybrid also has a broken suspension. It was bouncing seconds after each minor bump in the road. Additionally it had an error saying that the hybrid battery was not holding charge that we noticed the moment we got into the car. Carmax said they charged it before dropping it off and then it was discharged completely when we received it. Plus we noticed that the back end of the car was 4-6" lower from the front end, whereas the front had a couple inch clearance over the tires and the back was covering the top couple inches of the tires. We switched from comfort to sport & it did seem to limit the bounce but still there is something clearly wrong so CARMAX towed it away Friday night in September the day I got the car. Carmax repaired the suspension with bmw parts & now 6 weeks later the suspension is broken again. Carmax has offered to repair but I’m very concerned that there is a bigger.I checked the VIN for recalls and searched the internet for similar issues with no luck. I also emailed BMW for their take and they said that they’ve never heard of any issues. . Are faulty suspensions a thing with this car??? Should I keep it if they fix?don't need a car with endless issues??

NHTSA ODI #11553491

Mileage unknown · May 22, 2023

Air BagsSuspension

Read full complaint

Warning appeared on my vehicle a few months ago stating something was wrong with the restraint system. While driving out of nowhere my vehicle on it's own accord will begin rocking really hard and it has become dangerous for passengers, myself or my animals in my car. Looking further into the issue, this is a common problem with X5's and people are made to believe its a sensor issue with a hefty price. There is a warranty for vehicles that 10 years or less older that is supposed to be provided by BMW but when I call both dealerships here in the area they state that does not exist. I am taking my vehicle to BWM tomorrow morning to try and get this issue fixed. I will know more tomorrow.

NHTSA ODI #11523359

Mileage unknown · May 11, 2023

Suspension

Read full complaint

Basing complaint on NHTSA ID 11439582 4/25/2023 Started vehicle on this morning and ride height was normal, while doing daily intown driving, noticed that ride became extremely bumpy. I drove to my neighborhood Midas shop for inspection. There was no code but there was a dash warning with my chassis, "Drive Moderately". Midas instructed me to contact my nearest BMW Dealership in the Woodlands (Texas). I then called and explained the chassis warning that displayed and the "drive moderately" Message. The Dealership told me that the soonest that they could even look at it would be on 5/4 even though that I explained that this is my work transportation. Seeing no other option to get me back on the road, I took the vehicle to my General European Repair shop located 1.8 miles from the Midas shop. During that move, I drove under 40 mph. At that point, the shop checked to find the rear suspension airbags were leaking. Having no other choice, the shop ordered and replaced the airbags with parts purchased at the BMW Dealership. My repair cost at this point is $1940.00. Upon completion of this, during the system check, It was also determined that the air suspension pump was defective and that it wasn't capable of lifting the vehicle. The part alone is an additional $1558.66, bringing my repair with labor to over $4000.00. After reading your summary of complaints on this issue, especially with my current mileage at 50,725, this seems to be a Manufacturer known issue. I am compiling a complete file on this issue and intend to submit it to BMW for review with the hope that they will do the right thing.

NHTSA ODI #11521509

Mileage unknown · Nov 6, 2021

Suspension

Read full complaint

My 2018 x5 had the rear driver side air bag suspension give out where makes the ride very bouncy and hard pound on the uneven roads where makes you lose control of the vehicle and possibly have an incident. Came across a few more X5 owners with the same issue and hasn’t been a recall for these years 14-18. Suspension air seems to just give out under 60,000 miles on many people I have talk to along with the dealership confirming this has been an issue with the X5 air suspension system, but no recall or fix of the issue. Please fix and change this part.I’m sure BMW is aware, but need to address before they are more accidents due to this.

NHTSA ODI #11439582

Official recalls

24V608000 · Electrical System:wiring:connectors/plugs/receptacles; Engine And Engine Cooling:cooling System:pump

Aug 13, 2024

BMW of North America, LLC. (BMW) is recalling certain 2012-2015 X1 sDrive28i, X1 xDrive28i, 2012-2016 Z4 sDrive28i, 528i, 528i xDrive, 328i, 328xi, 2016-2018 X5 xdrive 40e, 2014-2016 228i, 228xi, 428i, 428i xDrive, 328xi Gran Turismo, 2013-2017 X3 sDrive28i, X3 xDrive28i, 2015-2018 X4 xDrive28i, 2015-2016 428xi vehicles. An improperly sealed electrical connector on the water pump may be exposed to water and short circuit.

Consequence & remedy

Consequence: An electrical short increases the risk of a fire.

Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.

Additional source detail variants (2)

Electrical System:wiring:connectors/plugs/receptacles

Consequence: An electrical short increases the risk of a fire.

Remedy: Dealers will inspect and replace the water pump and plug connector as necessary, and install a protective shield, free of charge. Owner notification letters were mailed on March 28, 2025. Owners may contact BMW customer service at 1-800-525-7417.

Engine And Engine Cooling:cooling System:pump

Consequence: An electrical short increases the risk of a fire.

21V586000 · Fuel System, Diesel:delivery:fuel Pump

Jul 29, 2021

BMW of North America, LLC (BMW) is recalling certain 2014-2018 328d, 328d xDrive, X5 xDrive35d, 2014-2016 535d, 535d xDrive, 2015 740Ld xDrive, and 2015-2017 X3 xDrive28d vehicles. The high-pressure fuel pump may fail.

Consequence & remedy

Consequence: Fuel pump failure can cause an engine stall while driving, increasing the risk of a crash.

Remedy: Dealers will replace the high-pressure fuel pump, free of charge. Owner notification letters were mailed on January 14, 2022. Owners may contact BMW customer service at 1-800-525-7417.

18V652000 · Equipment:electrical

Sep 20, 2018

BMW of North America, LLC (BMW) is recalling certain 2018 BMW 330e iPerformance, i3 Rex, i3 Sport Rex, X5 xDrive40e, i3 BEV, i3 Sport BEV and 2019 i8 and i8 Roadster vehicles and 2018-2019 530e iPerformance, 530e xDrive iPerformance and 740Le xDrive iPerformance vehicles. Capacitors within the TurboCord Portable Chargers may fail, possibly resulting in a shock hazard or a fire.

Consequence & remedy

Consequence: An electrical shock or a fire can increase the risk of injury or death.

Remedy: BMW will notify owners, and dealers will inspect the charging cable, and replace it if necessary, free of charge. The recall began February 22, 2019. Owners may contact BMW customer service at 1-800-525-7417.

18V439000 · Suspension:front:control Arm:lower Arm

Jun 28, 2018

BMW of North America, LLC (BMW) is recalling certain 2018 BMW X5 xDrive35i, X5 xDrive50i, X5 xDrive35d, and X6 sDrive35i vehicles. The pivot bolt on the front lower-left control arm may not have been properly hardened, which may cause the control arm to break.

Consequence & remedy

Consequence: If the lower control arm breaks, vehicle handling and control can be affected, increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect the lower-left control arms and replace if necessary, free of charge. The recall began July 11, 2018. Owners may contact BMW customer service at 1-800-525-7417.

17V727000 · Suspension

Nov 17, 2017

BMW of North America, LLC (BMW) is recalling certain 2018 BMW X5 SAV, X5 M SAV, X6 SAV, and X6 M SAV vehicles. Bolts that secure the front suspension may not have been properly tightened.

Consequence & remedy

Consequence: Loose bolts can affect the performance of the suspension, thereby increasing the risk of a crash.

Remedy: BMW will notify owners, and dealers will inspect and tighten the wishbone suspension bolts, free of charge. The recall is expected to begin January 8, 2018. Owners may contact BMW customer service at 1-800-525-7417.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

EA23001 · High Pressure Fuel Pump Failure

Opened Mar 17, 2023 · No close date supplied

Status: open (inferred from source dates) · Fuel System, Diesel:delivery:fuel Pump

The Office of Defects Investigation (ODI) opened PE21-021 on October 14, 2021, to investigate incidents alleging a stall/loss of motive power as a result of high-pressure fuel pump failures in certain model year (MY) 2019-2020 Ram 2500, 3500, 4500, and 5500 heavy duty trucks equipped with 6.7L Cummins turbodiesel engines. During the investigation, ODI sought to determine if the related defect allegation was limited in scope to the recalled population. After review of information request response materials from both FCA and BMW, NHTSA determined that sufficient information to identify a comprehensive recall population could not be produced by FCA and BMW.During the investigation FCA filed recalls 22V406, 22E048, 22V767, and 22E087 which include vehicles not identified in the initial subject population by ODI. ODI also received recall 21V586, involving loss of motive power due to failed CP4 fuel pumps on certain BMW manufactured vehicles. An information request letter response received from BMW indicated that failed pumps on their vehicles were caused by an interaction between pump internal components and US market diesel fuel, leading to increased slip and eventual particle-generating wear surface. Additional work will be done to identify whether a similar root cause is associated with the FCA recalled population and if similar wear dynamics occur on pumps supplied to vehicle manufacturers other than those included in the recalled population.ODI has upgraded this investigation to an EA in order to 1) determine engineering specifications of internal pump components that are correlated with pump failure leading to loss of motive power or other safety related hazards, 2) identify vehicle populations equipped with alleged defective pump variants, 3) assess if vehicles equipped with alleged defective pump variants result in an unreasonable risk to motor vehicle safety and 4) gather and review any other relevant information related to high pressure fuel pump failure associated with the subject populations of recalls 21V586, 21V880, 21E094, 22V406, 22E048, 22V767, and 22E087.Review of the above information will allow NHTSA to confirm root cause and recall remedy viability, and identify and evaluate vehicle populations equipped with pump components that may pose an unreasonable risk to motor vehicle safety.The ODI reports cited above can be reviewed at: http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID using the following complaint identification numbers: 11257550, 11351441, 11361603, 11361616, 11365300, 11365426, 11365858, 11366401, 11372337, 11373793, 11374797, 11376793, 11377871, 11378173, 11384377, 11386063, 11387018, 11399710, 11402550, 11415339, 11418868, 11418870, 11427075, 11434276, 11436807, 11437226, 11437249, 11437273, 11437292, 11437294, 11437394, 11437399, 11437403, 11437405, 11437423, 11437528, 11437565, 11437579, 11437580, 11437590, 11437679, 11437744, 11437781, 11437842, 11437993, 11438006, 11438008, 11438121, 11438138, 11438155, 11438392, 11438629, 11439359, 11439879, 11440397, 11443030, 11446542, 11448163, 11453556, 11458918, 11460558, 11469337

DP22005 · Pedestrian Alert Sounds

Opened Jan 27, 2023 · Closed Aug 7, 2023

Status: closed (inferred from source dates) · Electrical System:propulsion System

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

Air Bags:frontal:passenger Side:inflator Module