← New search

2004 BMW 745LI

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2004 BMW 745LI do not stand out strongly from the model-year median of 25.

About this comparison →

How this year compares

Owner complaints by model year

Other model years Selected year
Compare all 745LI years →

Counts vary with age, sales and reporting. They are not failure rates.

What owners reported most

All reported categories

Tap a category to read its complaints. One report may name several components.

When problems were reported

Mileage at the reported incident

30 reports with mileage · 3 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Power Train. Review the 11 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 9 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Engine. Review the 6 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

1 crash reports1 fire reports0 injury reports

Engine complaints

6 reports
Clear category filter
160,000 miles · May 30, 2018
EnginePower TrainWheels

TL* THE CONTACT OWNS A 2004 BMW 745LI. WHILE DRIVING UNKNOWN SPEEDS, THE VEHICLE HESITATED AND THE CHECK ENGINE INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC AND IT WAS DIAGNOSED THAT OIL WAS LEAKING ONTO THE MANIFOLD. ALSO, THE WHEELS AND AXLE NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE VE…

Read full complaint

TL* THE CONTACT OWNS A 2004 BMW 745LI. WHILE DRIVING UNKNOWN SPEEDS, THE VEHICLE HESITATED AND THE CHECK ENGINE INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC AND IT WAS DIAGNOSED THAT OIL WAS LEAKING ONTO THE MANIFOLD. ALSO, THE WHEELS AND AXLE NEEDED TO BE REPLACED. THE VEHICLE WAS NOT REPAIRED. THE VEHICLE WAS TAKEN TO BMW OF STRATHAM (71 PORTSMOUTH AVENUE, STRATHAM, NH 03885, (603) 772-0000), BUT WAS NOT DIAGNOSED OR REPAIRED. THE DEALER REFUSED TO WORK ON THE VEHICLE AND ADVISED THE CONTACT TO PURCHASE AN AFTERMARKET WARRANTY. THE CONTACT DECLINED THE RECOMMENDATION. THE MANUFACTURER WAS NOT NOTIFIED. THE FAILURE MILEAGE WAS 160,000.

NHTSA ODI #11098844

95,000 miles · Jun 1, 2016
Engine

ENGINE VALVE GUIDE SEALS MADE OF IMPROPER MATERIAL THAT FAILS CAUSING OIL LEAKAGE INTO EXHAUST, FOULING OF CATALYTIC CONVERTER, FAILURE TO PASS INSPECTION AND POLLUTION. THE VALVE GUIDE SEALS ARE NOT COMPATIBLE WITH HIGH ENGINE TEMPERATURES WHICH CAUSES THE SEALS TO FAIL AT 80,000 TO 120,000 MILES. MY SEALS FAILED AT APP…

Read full complaint

ENGINE VALVE GUIDE SEALS MADE OF IMPROPER MATERIAL THAT FAILS CAUSING OIL LEAKAGE INTO EXHAUST, FOULING OF CATALYTIC CONVERTER, FAILURE TO PASS INSPECTION AND POLLUTION. THE VALVE GUIDE SEALS ARE NOT COMPATIBLE WITH HIGH ENGINE TEMPERATURES WHICH CAUSES THE SEALS TO FAIL AT 80,000 TO 120,000 MILES. MY SEALS FAILED AT APPROXIMATELY 95,000 MILES CAUSING OIL CONSUMPTION IN EXCESS OF 1 QUART PER THOUSAND MILES. REPLACEMENT OF THE VALVE SEALS REQUIRES EXTENSIVE ENGINE READ DOWN AND COSTS APPROXIMATELY $9,000 TO REPAIR.

NHTSA ODI #10871765

104,000 miles · Jun 1, 2016
Engine

COOLANT TRANSFER PIPE SEAL IS MADE OF IMPROPER MATERIAL THAT IS NOT COMPATBLE WITH HIGH ENGINE TEMPERATURES. SEAL FAILS CAUSING LOSS OF ENGINE COOLANT. SEAL FAILS AT 40,000 TO 110,000 MILES. REPAIR IS APPROXIMATELY $6,000 BECAUSE ENGINE MUST BE TAKEN APART TO REPLACE THE SEAL. MY SEAL FAILED AT 104,000 MILES. LOSS OF POW…

Read full complaint

COOLANT TRANSFER PIPE SEAL IS MADE OF IMPROPER MATERIAL THAT IS NOT COMPATBLE WITH HIGH ENGINE TEMPERATURES. SEAL FAILS CAUSING LOSS OF ENGINE COOLANT. SEAL FAILS AT 40,000 TO 110,000 MILES. REPAIR IS APPROXIMATELY $6,000 BECAUSE ENGINE MUST BE TAKEN APART TO REPLACE THE SEAL. MY SEAL FAILED AT 104,000 MILES. LOSS OF POWER STEERING AND VEHICLE STABILITY CONTROL DUE TO COOLANT LEAK ONTO SERPENTINE BELT.

NHTSA ODI #10871762

130,000 miles · Apr 17, 2014
Electrical SystemEngineFire

TL* THE CONTACT OWNS A 2004 BMW 745LI. THE CONTACT STATED THAT THERE HAD BEEN AN EXTENSIVE OIL LEAK FROM THE VEHICLE. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER SEVERAL TIMES BUT THE FAILURE WAS NOT ABLE TO BE DUPLICATED OR DIAGNOSED. THE CONTACT ALSO DESCRIBED A BURNING METAL AND OIL ODOR IN ADDITION TO A WHILE CLOUD OF SMO…

Read full complaint

TL* THE CONTACT OWNS A 2004 BMW 745LI. THE CONTACT STATED THAT THERE HAD BEEN AN EXTENSIVE OIL LEAK FROM THE VEHICLE. THE VEHICLE WAS TAKEN TO AN AUTHORIZED DEALER SEVERAL TIMES BUT THE FAILURE WAS NOT ABLE TO BE DUPLICATED OR DIAGNOSED. THE CONTACT ALSO DESCRIBED A BURNING METAL AND OIL ODOR IN ADDITION TO A WHILE CLOUD OF SMOKE. THE ALTERNATOR AND BATTERY WERE REPAIRED TWICE BY AN INDEPENDENT MECHANIC HOWEVER, THE FAILURE PERSISTED. THE VEHICLE WAS THEN TAKEN TO A DIFFERENT REPAIR FACILITY WHERE THE CONTACT WAS ADVISED THAT THE ALTERNATOR, ALTERNATOR SEAL GASKET, VALVE AND SEALS NEEDED TO BE REPLACED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE MULTIPLE TIMES. THE APPROXIMATE FAILURE MILEAGE WAS 130,000. ..UPDATED 05/20/14 *BF UPDATED 06/02/2014 *JS

NHTSA ODI #10583375

73,245 miles · Apr 8, 2014
Engine

TL* THE CONTACT OWNS A 2004 BMW 745LI. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 25 MPH, THE ENGINE STALLED. THE CONTACT MENTIONED THAT THERE WERE NO WARNING LIGHTS ILLUMINATED. THE VEHICLE RESTARTED ON THE FIRST ATTEMPT AND RESUMED NORMALLY. THE FAILURE RECURRED ON SEVEN SEPARATE OCCASIONS. THE VEHICLE WAS TAKEN TO A …

Read full complaint

TL* THE CONTACT OWNS A 2004 BMW 745LI. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 25 MPH, THE ENGINE STALLED. THE CONTACT MENTIONED THAT THERE WERE NO WARNING LIGHTS ILLUMINATED. THE VEHICLE RESTARTED ON THE FIRST ATTEMPT AND RESUMED NORMALLY. THE FAILURE RECURRED ON SEVEN SEPARATE OCCASIONS. THE VEHICLE WAS TAKEN TO A DEALER WHERE THE FAILURE WAS UNABLE TO BE DIAGNOSED. THE DEALER AND MANUFACTURER WERE MADE AWARE OF THE FAILURE. THE FAILURE AND CURRENT MILEAGE WAS 73,245. UPDATED 5/8/14*CN THE CONSUMER STATED THE ENGINE KEPT RUNNING AND DID NOT DIE.

NHTSA ODI #10578275

90,000 miles · Jan 8, 2013
Engine

TL* THE CONTACT OWNS A 2004 BMW 745LI. THE CONTACT STATED THAT THERE WAS AN OIL LEAK FROM THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THEY ADVISED HIM THAT THE HOSE TO THE ENGINE WAS FRACTURED, CAUSING THE OIL LEAK. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS CONTACTED ABOUT THE ISSUE AND OFFERED N…

Read full complaint

TL* THE CONTACT OWNS A 2004 BMW 745LI. THE CONTACT STATED THAT THERE WAS AN OIL LEAK FROM THE VEHICLE. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THEY ADVISED HIM THAT THE HOSE TO THE ENGINE WAS FRACTURED, CAUSING THE OIL LEAK. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS CONTACTED ABOUT THE ISSUE AND OFFERED NO ASSISTANCE. THE FAILURE AND CURRENT MILEAGES WERE APPROXIMATELY 90,000. THE VIN WAS UNAVAILABLE.

NHTSA ODI #10491870

Official recalls

0

No recalls in this snapshot.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

2

EA12002 · Vehicle Rollaway

Opened Apr 10, 2012 · Closed Jan 24, 2013

Status: closed (inferred from source dates) · Electrical System; Electrical System:ignition; Electrical System:ignition:switch; Power Train:automatic Transmission

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

Additional source detail variants (4)

Electrical System

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

Electrical System:ignition

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

Electrical System:ignition:switch

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

Power Train:automatic Transmission

In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770

PE11025 · Vehicle Rollaway

Opened Aug 5, 2011 · Closed Apr 23, 2012

Status: closed (inferred from source dates) · Electrical System; Power Train:automatic Transmission

In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat

Additional source detail variants (2)

Electrical System

In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat

Power Train:automatic Transmission

In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat