IllustrationWITHOUT WARNING, THE HOOD LATCH UNLOCKED AND CAUSED THE HOOD TO OPEN WHILE DRIVING , HAPPENED ON SEVERAL OCCASIONS SINCE 2017/1/23. DEALERSHIP HAS TO SEE IT HAPPEN IN ORDER TO FIX. MILEAGE 100858 AT TIME I FIRST NOTICE IT.
2003 BMW 7 Series
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all 7 Series years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 7 of 8 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Equipment. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
8 reportsTHE CONTACT OWNS A 2003 BMW 745LI. AFTER THE VEHICLE WAS SERVICED, THE AIR BAG WARNING LIGHT ILLUMINATED CONTINUOUSLY. IN ADDITION, THE TENSION SEAT BELT WARNING LIGHT ILLUMINATED. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE APPROXIMATE FAILURE MILEAGE WAS 101,082.
SEAT BELT RESTRAINT TENSIONER FAULTY
CAR DOES NOT START CORRECTLY AND STALLS WHILE SITTING AT LIGHTS. IT ALSO CUTS OFF WHILE DRIVING. *TR
TIRES UNEVEN WEAR. *TT
TL* THE CONTACT OWNS A 2003 BMW 7 SERIES. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN ID NUMBER: 10V446000 (COMPONENT: SERVICE BRAKES, HYDRAULIC: POWER ASSISTS: VACUUM). THE VEHICLE WAS TAKEN TO THE DEALER AND THE CONTACT WAS INFORMED THAT THE VACUUM PUMP WAS LEAKING BUT WOULD NOT BE REPAIRED UNDER THE RECALL. THE DEALER…
Read full complaint
TL* THE CONTACT OWNS A 2003 BMW 7 SERIES. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN ID NUMBER: 10V446000 (COMPONENT: SERVICE BRAKES, HYDRAULIC: POWER ASSISTS: VACUUM). THE VEHICLE WAS TAKEN TO THE DEALER AND THE CONTACT WAS INFORMED THAT THE VACUUM PUMP WAS LEAKING BUT WOULD NOT BE REPAIRED UNDER THE RECALL. THE DEALER ADVISED THAT ONLY THE VACUUM LINE HOSE WAS COVERED UNDER THE RECALL AND NOT THE PUMP. THE VACUUM PUMP WOULD BE THE RESPONSIBILITY OF THE CONTACT. THE MANUFACTURER WAS CONTACTED AND DID OFFER ASSISTANCE WITH THE REPAIRS. THE FAILURE MILEAGE WAS 62,300. UPDATED 01/28/11 *BF UPDATED 02/03/11*JB
DRIVING ON INTERSTATE 295S IN WASHINGTON DC AROUND 11:30PM ON DEC 28TH 2008. ALL OF A SUDDEN I HEAR A LOUD BANG AND IMMEDIATELY LOSS CONTROL OF VEHICLE. I SWERVED TO THE RIGHT SHOULDER OF THE INTERSTATE AND STOPPED THE VEHICLE. UPON INSPECTING VEHICLE I NOTICED MY DRIVERS SIDE FRONT AND REAR TIRE WAS FLAT. WITH THE ASSISTANCE OF…
Read full complaint
DRIVING ON INTERSTATE 295S IN WASHINGTON DC AROUND 11:30PM ON DEC 28TH 2008. ALL OF A SUDDEN I HEAR A LOUD BANG AND IMMEDIATELY LOSS CONTROL OF VEHICLE. I SWERVED TO THE RIGHT SHOULDER OF THE INTERSTATE AND STOPPED THE VEHICLE. UPON INSPECTING VEHICLE I NOTICED MY DRIVERS SIDE FRONT AND REAR TIRE WAS FLAT. WITH THE ASSISTANCE OF A POLICE OFFICER I PROCEEDED TO CHANGE THE TIRES WITH A SPARE AND ANOTHER TIRE MY FAMILY MEMBER BROUGHT FROM HOME. THIS IS WHEN I NOTICED THAT THE REAR RIM WAS COMPLETELY SPLIT AND THE INSIDE RING WAS RESTING ON THE BREAK ASSEMBLY. THEN I NOTICED THE FRONT RIM HAD SIMILAR DAMAGE IN THAT IT WAS COMPLETELY SPLIT AROUND THE INSIDE DIAMETER OF THE RIM. *TR
BRAND NEW BMW 760LI , SEAT MEMORY DOES NOT OPERATE AND MOVE THE SEATS PROPERLY WHEN CAR IS REMOTELY UNLOCKED AS PER THE CARS OPERATING MANUAL AND LISTED FEATURES. BMW NORTH AMERICA TOLD US THEY CANNOT FIX THE PROBLEM UNTIL SEPTEMBER WITH AN UPDATE. THE VEHICLE HAS BEEN IN SERVICE FOR OVER 14 DAYS FOR THIS PROBLEM. WHO PAYS THIS…
Read full complaint
BRAND NEW BMW 760LI , SEAT MEMORY DOES NOT OPERATE AND MOVE THE SEATS PROPERLY WHEN CAR IS REMOTELY UNLOCKED AS PER THE CARS OPERATING MANUAL AND LISTED FEATURES. BMW NORTH AMERICA TOLD US THEY CANNOT FIX THE PROBLEM UNTIL SEPTEMBER WITH AN UPDATE. THE VEHICLE HAS BEEN IN SERVICE FOR OVER 14 DAYS FOR THIS PROBLEM. WHO PAYS THIS KIND OF MONEY TO BE TOLD YOU HAVE TO WAIT ANOTHER MONTH FOR A SOLUTION, A SIMPLE ONE.*AK
Official recalls
210V446000 · Service Brakes, Hydraulic:power Assist:vacuum
Oct 1, 2010
BMW IS RECALLING CERTAIN MODEL YEAR 2004-2010 5-SERIES, 6-SERIES, AND MODEL YEAR 2002-2008 7-SERIES VEHICLES. A CHECK VALVE OF THE BRAKE VACUUM PUMP MAY LEAK A SMALL AMOUNT OF LUBRICATING OIL. OVER TIME THIS COULD RESULT IN CONTAMINATION OF THE BRAKE BOOSTER.
Consequence & remedy
Consequence: POWER ASSIST BRAKING PERFORMANCE COULD BE ADVERSELY AFFECTED. IN EXTREME CASES THERE COULD BE A COMPLETE LOSS OF POWER ASSIST BRAKING. AN UNEXPECTED REDUCTION OR LOSS IN POWER BRAKING ASSIST MAY INCREASE THE RISK OF A CRASH.
Remedy: BMW WILL NOTIFY OWNERS AND DEALERS WILL REPAIR THE VEHICLES FREE OF CHARGE. THE SAFETY RECALL BEGAN ON NOVEMBER 24, 2010. OWNERS MAY CONTACT BMW AT 1-800-525-7417.
04V575000 · Seats:front Assembly:seat Heater/cooler
Dec 6, 2004
ON CERTAIN PASSENGER VEHICLES EQUIPPED WITH FRONT SEAT HEATING SYSTEMS, UPON ENTERING AND EXITING THE VEHICLE, EXCESSIVE CONTACT WITH THE SIDE BOLSTER THAT IS CONTAINED IN THE SEAT'S BACKREST MAY DAMAGE THE HEATING MAT LOCATED IN THIS AREA. IF SUCH DAMAGE WERE TO OCCUR, WITH THE SYSTEM TURNED ON, THE VEHICLE OCCUPANT MAY FEEL EXCESSIVE HEAT FROM THIS AREA.
Consequence & remedy
Consequence: IT IS POSSIBLE THAT THE HEATING MAT IN THE BACKREST'S SIDE BOLSTER COULD OVERHEAT AND DAMAGE, OR MELT A SMALL HOLE IN, THIS AREA OF THE SEAT COVER. IF THIS HAPPENED, IT COULD LEAD TO AN OCCUPANT BEING BURNED.
Remedy: DEALERS WILL MODIFY THE SEAT HEATING CIRCUIT. THE RECALL IS EXPECTED TO BEGIN DURING DECEMBER 2004. OWNERS SHOULD CONTACT BMW AT 1-800-831-1117.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA12002 · Vehicle Rollaway
Opened Apr 10, 2012 · Closed Jan 24, 2013
Status: closed (inferred from source dates) · Electrical System; Electrical System:ignition; Electrical System:ignition:switch; Power Train:automatic Transmission
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Additional source detail variants (4)
Electrical System
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Electrical System:ignition
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Electrical System:ignition:switch
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
Power Train:automatic Transmission
In a letter dated October 16, 2012, BMW of North America, LLC (BMW) submitted a Defect Information Report (DIR), NHTSA Recall No. 12V-502 to NHTSA identifying a safety defect involving the possibility of unattended vehicle rollaway in MY 2005 through 2008 BMW 7-Series (approximately 45,000) vehicles equipped with the Comfort Access Option.The Comfort Access option allows the driver to start and stop the engine (by pressing the engine start / stop button) without inserting the key fob into the vehicles key slot in the instrument panel.Subject vehicles not equipped with the Comfort Access option require the key fob be inserted the key slot to start the engine.Upon removal of the key from the key slot the vehicle will automatically shift to Park if the driver has not done so using the gearshift lever.Sunject vehicles equipped with the Comfort Access option are designed such that when the vehicle is stopped with the service brakes applied and the transmission in Drive or Reverse, the driver can push the engine start/stop button one time, stopping the engine and automatically shifting the transmission to Park.In its DIR, BMW identified a condition such that if the driver depressed the start-stop button multiple times in rapid succession, the transmission could shift to Neutral instead of Park.With the transmission in neutral, depending on the slope of the road, the vehicle could rollaway if unattended.In review of data submitted to the Office of Defects Investigation (ODI) and of reports submitted to BMW, ODI identified 20 reports alleging vehicle rollaway involving vehicles equipped with Comfort Access.The vehicles identified in these reports are all subject to recall 12V-502.Ten of these reports were identified as likely related to the defect described in recall 12V-502.Two of the reports are likely related to other mechanical failures.The remaining 8 allegations of vehicle rollaway could not be associated with a specific cause.There are 32 reports alleging vehicle rollaway in the subject vehicles not equipped with the Comfort Access option.A vehicle based safety defect trend was not identified in these reports.Subject vehicles not equipped the Comfort Access option will automatically shift to Park once the key fob is removed from the key slot.In this regard these vehicles behave similarly to those with traditional mechanical keys where the key cannot be removed from the ignition unless the vehicle is shifted to Park.The difference between these vehicles and the subject vehicles with the Comfort Access option is that in the Comfort Access equipped vehicles, the engine can be started and stopped without the key fob in the key slot.ODI reports 10429922 and 10419177 noted in the EA opening resume were determined to be vehicles not equipped with the Comfort Access option and ODI did not identify a vehicle based safety defect associated with these incidents.This investigation is closed.The ODI report cited above can be reviewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification (ODI) numbers:10185770
PE11025 · Vehicle Rollaway
Opened Aug 5, 2011 · Closed Apr 23, 2012
Status: closed (inferred from source dates) · Electrical System; Power Train:automatic Transmission
In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat
Additional source detail variants (2)
Electrical System
In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat
Power Train:automatic Transmission
In response to the Office of Defects Investigation's (ODI) Information Request (IR) for PE11-025, BMW provided ODI with 1 complaint and 46 field reports relating to either incidents of unattended vehicle rollaway or vehicle movement after the driver expected the vehicle gearshift to automatically shift to park. ODI's analysis of the data provided by BMW identified 14 crashes and 5 alleged injuries. ODI has also identified 3 additional reports in its database alleging vehicle rollaway incidents of which 2 resulted in crashes.The subject vehicles are all equipped with push-buttons (Start/Stop button) to control starting/stopping the engine and Shift-by-Wire gearshift systems controlled by a column mounted selector lever behind the steering wheel. The Start/Stop button also controls switching the ignition and the radio ready state On and Off. Shift-by-wire systems replace the traditional mechanical connection (e.g., cable or linkage) between the gearshift and automatic transmission with an electronic connection controlled by a computer module. When parking the vehicle, the driver has the capability to manually shift the vehicle to park by pressing the Park button on the end of the electronic gearshift lever. However, the instructions for engine shutoff provided in the owner's manual state that pressing the Start/Stop button serves the dual function of switching off the engine and automatically shifting the transmission to Park.In response to ODI's information request for PE11-025, BMW described several circumstances where the subject vehicles may shift to neutral when the driver may expect it to automatically shift to park. First, for Comfort Access System (CAS) vehicles, if the transmission is in neutral when the key fob is in the ignition slot and the Start/Stop button is pressed to shut-off the engine, the transmission will remain in neutral. This is referred to as the Carwash mode and is a normal operating feature of the vehicles that is described in the owner's manual. BMW also described two circumstances that are not normal operating features and are not described in the owners' manual: (1) with the transmission in drive or reverse and the engine running, if the Start/Stop button is pushed 2 or 3 times within a 0.3 second to 0.5 second interval, the engine will stop and the transmission will shift to Neutral; and 2) if the Park button on the gearshift lever is pressed at the same time that the gearshift lever is actuated (i.e., toggled up or down) to select drive, reverse or neutral; the transmission will shift to neutral or remain in neutral.Beginning in model year (MY) 2005, BMW introduced CAS as an optional feature package for the subject vehicles.The key for CAS equipped vehicles is an electronic code that is sent to the engine control module by a remote transmitter (key fob). An optional docking port (key slot) is provided for driver convenience or to put the vehicle into Car Wash mode, which allows for engine shutoff in neutral. BMW sold approximately 45,000 subject vehicles with CAS and approximately 94 percent of the CAS equipped vehicles were produced from MY 2006 through 2008. Non-CAS subject vehicles were produced from MY 2002 through 2008 and require the remote control to be in the ignition slot located next to the Start/Stop button to start the engine.The 50 incidents identified by ODI's analysis of complaints and field reports include 18 involving CAS vehicles (39.6 incidents per 100,000 vehicles) and 32 involving non-CAS vehicles (42.0 incidents per 100,000 vehicles). Because the incidents are considered random events, the failure rates were also adjusted for vehicle exposure, resulting in rat