Engine. Review the 3 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Fuel/propulsion System. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Air Bags. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

0 crash reports0 fire reports0 injury reports

Structure complaints

1 reports

Clear category filter

5,150 miles · Jan 11, 2013

Structure

Read full complaint

THIS CAR HAS NO "SAFETY CATCH" ON THE HOOD LATCH THAT THE OWNER OPENS AFTER FIRST RELEASING THE HOOD FROM INSIDE THE CAR. INSTEAD, THE OWNER OPENS THE HOOD BY PULLING TWICE ON THE HOOD RELEASE LEVEL INSIDE THE CAR IN THE DRIVER'S FOOTWELL. THE HOOD THEN OPENS FREELY WITHOUT FURTHER UNLATCHING OUTSIDE THE CAR. THE PROBLEM IS THAT THIS LATCH SYSTEM FAILS TO CLOSE THE HOOD PROPERLY. OFTEN ONE SIDE OR THE OTHER WILL NOT LATCH FIRMLY INTO PLACE. SO, INSTEAD OF TWO LATCHES HOLDING THE HOOD DOWN, ONLY ONE DOES. I TOOK MY CAR TO A DEALER FOR THIS PROBLEM, WHO DIAGNOSED IT HAS BEING CAUSED BY "LEAVES" IN THE MECHANISM. HOWEVER, THE PROBLEM HAS RECURRED ON BOTH THE SIDE THEY CLEANED (THE PASSENGER'S SIDE) AND ON THE DRIVER'S SIDE LATCHES. IT IS UNSAFE TO DRIVE THIS CAR WITH THE HOOD ONLY PARTIALLY LATCHED CLOSED, AS I AM SURE YOU WILL AGREE. OWNERS ARE COMPLAINING OF THIS SAFETY PROBLEM. SEE THIS DISCUSSION AND A PICTURE OF THE IMPROPERLY CLOSED HOOD ONLINE ON A BMW FORUM: HTTP://WWW.F30POST.COM/FORUMS/SHOWTHREAD.PHP?T=790560. *TR

NHTSA ODI #10492311

Official recalls

23V707000 · Engine And Engine Cooling:engine

Oct 20, 2023

BMW of North America, LLC (BMW) is recalling certain 2010-2012 1 Series Coupe, 1 Series Convertible, 3 Series Sedan, 3 Series Convertible, 2010-2011 3 Series Sportswagon, 3 Series Coupe, 5 Series Sedan, X3 xDrive 28i, X3 xDrive 30i, X5 xDrive30i, and Z4 sDrive30i vehicles. The aluminum bolts that secure the housing for the variable camshaft timing adjustment (VANOS) unit can loosen over time and possibly break.

Consequence & remedy

Consequence: Loose or broken VANOS unit bolts can result in an engine stall, increasing the risk of a crash.

Remedy: Dealers will replace the four VANOS bolts, free of charge. Interim letters notifying owners of the safety risk are expected to be mailed December 18, 2023. Owner notification letters were mailed June 19, 2024. Owners may contact BMW customer service at 1-800-525-7417.

22V119000 · Engine And Engine Cooling:exhaust System:emission Control:crankcase (pcv)

Mar 2, 2022

BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.

Consequence & remedy

Consequence: An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.

Remedy: This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.

12V176000 · Seats:front Assembly:head Restraint

Apr 20, 2012

BMW IS RECALLING CERTAIN MODEL YEAR 2012 BMW 3-SERIES VEHICLES MANUFACTURED FROM OCTOBER 19, 2011, THROUGH MARCH 18, 2012, THAT HAVE FRONT SEAT HEAD RESTRAINTS THAT EXCEED THE DOWNWARD MOVEMENT LIMIT OF 25MM IN THE HIGHEST POSITION. THUS, THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 202A,"HEAD RESTRAINTS."

Consequence & remedy

Consequence: IN THE EVENT OF A VEHICLE CRASH, THE HEAD RESTRAINT MAY UNEXPECTEDLY MOVE DOWN SLIGHTLY IF IT WAS ADJUSTED TO THE FULLY EXTENDED POSITION, INCREASING THE RISK OF PERSONAL INJURY.

Remedy: BMW WILL NOTIFY OWNERS, AND DEALERS WILL ATTACH A CLAMP TO THE FRONT SEAT HEAD RESTRAINT POSTS, FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 30, 2012. OWNERS MAY CONTACT BMW CUSTOMER RELATIONS AND SERVICES AT 1-800-525-7417.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

PE13030 · Loss Of Power Assist Braking

Opened Sep 6, 2013 · Closed Oct 25, 2013

Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum

In a letter dated September 26, 2013, BMW Group submitted a safety recall notice to NHTSA identifying a defect condition in the vacuum pump oil supply that may result in loss of power assist braking in 76,191 model year (MY) 2012 through 2014 BMW 3-Series, 5-Series, X1 SAV, X3 SAV, and Z4 vehicles equipped with 4-cylinder engines (NHTSA Recall 13V-454).According to BMW, movement of the seal disk within the camshaft may result in blocking of the oil supply to the vacuum pump, resulting in improper pump operation and loss of power assist braking.On July 11, 2013, BMW initiated a change to the camshaft geometry that prevented the seal disk from blocking the oil port.BMW has not received any braking complaints related to loss of power assist after the design change was implemented in production.The owners of all affected vehicles will be contacted by mail and asked to take their vehicle to a BMW dealer who will install a locking ring into the camshaft to keep the seal disk in its proper location.BMW expects to begin dealer and owner notification in November 2013 and complete dealer and owner notification in December when the remedy is expected to be available.Based on the actions taken by BMW, this investigation is closed.