BRAKE LIGHTS ON BOTH SIDES GETS STUCK ON ONCE THE PEDAL IS PRESSED. THIS PRODUCES NO ERROR CODES. I WAS TOLD IT COULD BE THE BRAKE PEDAL PRESSURE SENSOR SWITCH. I CHANGED THIS AND IT DID NOTHING. THIS IS VERY DANGEROUS TO OTHER DRIVERS BECAUSE THEY ARE NOT SURE IF THE CAR IS BRAKING AS THE LIGHT IS ALWAYS ON AND WILL BURN OUT TH…
Read full complaint
BRAKE LIGHTS ON BOTH SIDES GETS STUCK ON ONCE THE PEDAL IS PRESSED. THIS PRODUCES NO ERROR CODES. I WAS TOLD IT COULD BE THE BRAKE PEDAL PRESSURE SENSOR SWITCH. I CHANGED THIS AND IT DID NOTHING. THIS IS VERY DANGEROUS TO OTHER DRIVERS BECAUSE THEY ARE NOT SURE IF THE CAR IS BRAKING AS THE LIGHT IS ALWAYS ON AND WILL BURN OUT THE BULBS AND MELT THE HOUSING IF CONSTANTLY ON. THIS CAN BE REPRODUCED EITHER WHILE PARKED OR IN MOTION.
NHTSA ODI #11220395
Mileage unknown · Nov 27, 2016
Exterior Lighting
THE ZKW XENON HEADLIGHTS HAVE A FLAW IN THE PLASTIC PROJECTOR HOUSING. THE HOUSING GETS TOO HOT AND MELTS AND THE LIGHT OUTPUT IS SEVERELY RESTRICTED. THIS HAPPENS TO 100% OF THE HEADLIGHTS MADE BY THIS MANUFACTURER AND IS A SAFETY ISSUE. THE REFLECTIVE COATING ON THE HEADLIGHTS MELTS AND THE LIGHT CAN NO LONGER BE PROJECTED O…
Read full complaint
THE ZKW XENON HEADLIGHTS HAVE A FLAW IN THE PLASTIC PROJECTOR HOUSING. THE HOUSING GETS TOO HOT AND MELTS AND THE LIGHT OUTPUT IS SEVERELY RESTRICTED. THIS HAPPENS TO 100% OF THE HEADLIGHTS MADE BY THIS MANUFACTURER AND IS A SAFETY ISSUE. THE REFLECTIVE COATING ON THE HEADLIGHTS MELTS AND THE LIGHT CAN NO LONGER BE PROJECTED OUT CORRECTLY. THE FOG LIGHTS ARE NOW BRIGHTER THEN THE HEADLIGHTS. THE VEHICLE CAN NO LONGER BE SAFELY DRIVEN AT NIGHT. SPARE PARTS ARE NOT AVAILABLE AND THE ONLY FIX IS TO REPLACE THE ENTIRE HEADLIGHTS AT A COST OF OVER $2000. THERE SHOULD BE A RECALL TO REPLACE THE HEADLIGHTS AS THIS IS A SAFETY ISSUE OF NOT BEING ABLE TO SEE.
NHTSA ODI #10928130
197,300 miles · May 21, 2014
Exterior Lighting
THERE IS LIMITED LIGHT OUTPUT FROM THE XENON/HID HEADLIGHT ASSEMBLIES DUE TO "MELTED" PROJECTOR BOWLS FROM BMW. THIS IS A SERIOUS SAFETY DEFECT THAT PREVENTS END USERS FROM BEING ABLE TO SEE THE ROAD AND OBJECTS AHEAD OF THEM. *TR
NHTSA ODI #10592995
70,000 miles · Feb 16, 2013
Exterior Lighting
OEM PROJECTOR HEADLIGHTS BURNT BEHIND PROJECTOR CAUSING VERY DIM LIGHTS. *TR
NHTSA ODI #10498383
115,650 miles · Nov 19, 2012
Exterior Lighting
MY TAIL LIGHTS AND TURN SIGNALS WORK FOR A WHILE THEN QUITE WORKING. THE EXACT SAME SYMPTOMS AS RECALL #11V438000 FOR THE SAME TYPE, MODEL AND YEAR AS MY CAR, BUT BMW SAYS MY VEHICLE IS NOT INCLUDED. *TR
NHTSA ODI #10485181
110,304 miles · Jun 23, 2012
Electrical SystemExterior Lighting
THE PROJECTOR BOWLS ON THE ZKW HEADLIGHTS WERE BURNT OUT DUE TO A DESIGN FLAW. I SEE LOT OF COMPLAINTS ONLINE WITH THE SAME ISSUE. DRIVING IN NIGHT IS REALLY DIFFICULT AND DANGEROUS. *TT
NHTSA ODI #10462866
Mileage unknown · Mar 24, 2012
Exterior Lighting
DUE TO THE PLASTIC BOWELS IN THE HEADLIGHT PROJECTORS, WHICH ARE CHROME LIKE LINED, AND THE HIGH HEAT OF THE HID BULBS, THIS CHROME LIKE COATING HAS BURNED OFF MAKING THE LIGHT OUTPUT OF MY HID HEAD LIGHTS VERY DIM. THE OUTSIDE OF THE BOWELS HAVE GONE FROM A CHROME LIKE COATING TO A BRONZE/CARAMEL COLOR/COATING. THIS PROBLEM IS …
Read full complaint
DUE TO THE PLASTIC BOWELS IN THE HEADLIGHT PROJECTORS, WHICH ARE CHROME LIKE LINED, AND THE HIGH HEAT OF THE HID BULBS, THIS CHROME LIKE COATING HAS BURNED OFF MAKING THE LIGHT OUTPUT OF MY HID HEAD LIGHTS VERY DIM. THE OUTSIDE OF THE BOWELS HAVE GONE FROM A CHROME LIKE COATING TO A BRONZE/CARAMEL COLOR/COATING. THIS PROBLEM IS VERY OBVIOUS. I HAVE HAD OTHER VEHICLES WITH HID HEADLIGHTS, AND THE LIGHT OUTPUT OF THOSE CARS IS EASILY DOUBLE OR MORE, TO THE POINT WHERE ALOT OF TIMES I HAVE TO DRIVE WITH MY FOG LIGHTS ON JUST TO LIGHT THE ROAD UP TO BE ABLE TO SEE WELL ENOUGH SO THAT I DON'T HAVE A ACCIDENT. I HAVE PICTURES I TOOK OF THE DISCOLORED BOWELS IM TALKING ABOUT ON MY PHONE THAT I WOULD BE ABLE TO SEND. *TR
NHTSA ODI #10452861
50,000 miles · Jan 18, 2012
Exterior Lighting
ZKW XENON HEADLIGHT REFLECTOR BOWL IS BURNED RESULTING IN VERY DIM LIGHT OUTPUT. I AM OFTEN AFRAID OF DRIVING AT NIGHT BECAUSE I FEEL IT IS A DANGER TO MY SAFETY.
NHTSA ODI #10444460
150,000 miles · Jan 13, 2012
Exterior Lighting
TL* THE CONTACT OWNS A 2003 BMW 323. THE CONTACT STATED THAT THE HEADLIGHTS WOULD FLICKER ON AND OFF. THE TURN SIGNAL LIGHT WOULD ALSO FLICKER ABNORMALLY. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THEY ADVISED HIM THAT THE TAILLIGHT ASSEMBLY NEEDED TO BE REPLACED. THE VEHICLE HAD NOT BEEN REPAIRED. THE MANUFACTURER …
Read full complaint
TL* THE CONTACT OWNS A 2003 BMW 323. THE CONTACT STATED THAT THE HEADLIGHTS WOULD FLICKER ON AND OFF. THE TURN SIGNAL LIGHT WOULD ALSO FLICKER ABNORMALLY. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE THEY ADVISED HIM THAT THE TAILLIGHT ASSEMBLY NEEDED TO BE REPLACED. THE VEHICLE HAD NOT BEEN REPAIRED. THE MANUFACTURER WAS CONTACTED AND THEY ADVISED THE CONTACT THAT THE VEHICLE WAS NOT INCLUDED IN NHTSA CAMPAIGN ID NUMBER: 11V438000 (EXTERIOR LIGHTING:TAIL LIGHTS). THE FAILURE MILEAGE WAS APPROXIMATELY 150,000.
NHTSA ODI #10443677
80,000 miles · Jan 2, 2012
Exterior Lighting
THE BMW E46 (3 SERIES BMW) THAT WAS MADE FROM 1999 TO 2006. IN SOME CASES DURING THESE YEARS THEY USED A LIGHTING MANUFACTURER "ZKW" FOR THEIR XENON HEADLIGHTS. UNFORTUNATELY THESE LIGHTS HAVE A COMMON FAILURE ISSUE COMMONLY REFERRED TO AS A "BURNT REFLECTOR" ON THE INTERNET AND ON BMW FORUMS. THIS IS A NON-CONSUMER REPLACEABL…
Read full complaint
THE BMW E46 (3 SERIES BMW) THAT WAS MADE FROM 1999 TO 2006. IN SOME CASES DURING THESE YEARS THEY USED A LIGHTING MANUFACTURER "ZKW" FOR THEIR XENON HEADLIGHTS. UNFORTUNATELY THESE LIGHTS HAVE A COMMON FAILURE ISSUE COMMONLY REFERRED TO AS A "BURNT REFLECTOR" ON THE INTERNET AND ON BMW FORUMS. THIS IS A NON-CONSUMER REPLACEABLE PART. WHEN THIS PART FAILS IT CAUSES THE VEHICLE TO NOT HAVE EFFECTIVE HEADLIGHTS. I PERSONALLY HAVE HAD TIMES WHERE MY FIELD OF VISION COULD NOT SEE ITEMS ON THE ROAD DUE TO THE DIM LIGHTS. THE ONLY REMEDY APPEARS TO BE TO REPLACE THE ENTIRE HEADLIGHT ASSEMBLY TO THE TUNE OF HUNDREDS OF DOLLARS (WELL OVER A THOUSAND IF YOU DO BOTH SIDES). IN MY OPINION BMW SHOULD CORRECT THIS ISSUE FOR THE CONSUMER. HEADLIGHTS ARE AN IMPORTANT SAFETY ITEM. TO HAVE A PART FAIL THAT IS NOT CONSUMER REPLACEABLE IS UNACCEPTABLE. MANY PEOPLE HAVE THIS ISSUE BUT HAVE NO WAY TO REMEDY IT. JUST GOOGLE IT OR CHECK E46FANATICS.COM. YOU WILL SEE THAT THERE ARE PLENTY OF PEOPLE THAT REALIZE THIS IS AN ISSUE. *TR
NHTSA ODI #10442114
Official recalls
0
No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3
EA09019 · Rear Lamp Illumination
Opened Dec 18, 2009 · Closed Sep 28, 2011
Status: closed (inferred from source dates) · Exterior Lighting; Exterior Lighting:brake Lights; Exterior Lighting:tail Lights; Exterior Lighting:turn Signal
In a letter submitted to the Office of Defects Investigation (ODI) dated August25, 2011, BMWindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.The issue involves the rear lamps in the vehicles body panel.Through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.This can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.The recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.An 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.BMW will complete dealer notification in September 2011 and will begin owner notification in October 2011.All 3 series sedans (except for the M3 sedan which utilized a different rear lamp assembly) that were built between September 1, 2001 and March 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.The action taken by BMW is sufficient to resolve the issues raised by this investigation.Accordingly, this investigation is closed.
Additional source detail variants (4)
Exterior Lighting
In a letter submitted to the Office of Defects Investigation (ODI) dated August25, 2011, BMWindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.The issue involves the rear lamps in the vehicles body panel.Through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.This can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.The recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.An 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.BMW will complete dealer notification in September 2011 and will begin owner notification in October 2011.All 3 series sedans (except for the M3 sedan which utilized a different rear lamp assembly) that were built between September 1, 2001 and March 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.The action taken by BMW is sufficient to resolve the issues raised by this investigation.Accordingly, this investigation is closed.
Exterior Lighting:brake Lights
In a letter submitted to the Office of Defects Investigation (ODI) dated August25, 2011, BMWindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.The issue involves the rear lamps in the vehicles body panel.Through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.This can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.The recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.An 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.BMW will complete dealer notification in September 2011 and will begin owner notification in October 2011.All 3 series sedans (except for the M3 sedan which utilized a different rear lamp assembly) that were built between September 1, 2001 and March 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.The action taken by BMW is sufficient to resolve the issues raised by this investigation.Accordingly, this investigation is closed.
Exterior Lighting:tail Lights
In a letter submitted to the Office of Defects Investigation (ODI) dated August25, 2011, BMWindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.The issue involves the rear lamps in the vehicles body panel.Through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.This can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.The recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.An 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.BMW will complete dealer notification in September 2011 and will begin owner notification in October 2011.All 3 series sedans (except for the M3 sedan which utilized a different rear lamp assembly) that were built between September 1, 2001 and March 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.The action taken by BMW is sufficient to resolve the issues raised by this investigation.Accordingly, this investigation is closed.
Exterior Lighting:turn Signal
In a letter submitted to the Office of Defects Investigation (ODI) dated August25, 2011, BMWindicated that it will conduct a voluntary recall campaign to remedy the subject vehicles.The issue involves the rear lamps in the vehicles body panel.Through normal vehicle use over time, the rear lamps ground wiring and associated 8-pin connector can experience an increase of the resistance at the electrical contact points.This can lead to intermittent or permanent loss of the rear lamp functions which include tail, brake, and turn signal operation.The recall consists of modifying the rear lamps in the vehicles body panel by adding a secondary ground connection in parallel to the existing primary ground connection.An 8-pin connector that attaches the primary ground wiring to the rear lamp assembly will also be inspected and replaced if necessary.BMW will complete dealer notification in September 2011 and will begin owner notification in October 2011.All 3 series sedans (except for the M3 sedan which utilized a different rear lamp assembly) that were built between September 1, 2001 and March 1, 2005 are included in this recall, totalling approximately 241,000 vehicles.The action taken by BMW is sufficient to resolve the issues raised by this investigation.Accordingly, this investigation is closed.
PE09036 · Rear Lamp Illumination
Opened Aug 7, 2009 · Closed Dec 22, 2009
Status: closed (inferred from source dates) · Exterior Lighting; Exterior Lighting:brake Lights; Exterior Lighting:tail Lights; Exterior Lighting:turn Signal
ODI HAS RECEIVED COMPLAINTS FROM CONSUMERS STATING THAT THEIR TAIL LIGHT ASSEMBLY IS NOT PROPERLY ILLUMINATING.THE TAIL LIGHT ASSEMBLY CONSISTS OF A TURN SIGNAL LAMP, A TAIL LAMP AND A BRAKE LAMP.THE COMPLAINANTS HAVE INDICATED THAT THE ISSUE IS WITH AN 8 PIN CONNECTOR AND ASSOCIATED GROUND WIRING.THESE COMPONENTS ARE ALLEGEDLY OVERHEATING AND MELTING DUE TO EXCESSIVE ELECTRICAL CURRENT THAT RUNS THROUGH THE SYSTEM.BMW ISSUED A TECHNICAL SERVICE BULLETIN (TSB) SIB-630306 ON FEBRUARY 2007 TO ADDRESS THE CONDITION BY ADDING SUPPLEMENTARY GROUND WIRING TO THE TAIL LAMP ASSEMBLY.ODI IS UPGRADING TO AN EA TO FURTHER INVESTIGATE THE ISSUE.
Additional source detail variants (4)
Exterior Lighting
ODI HAS RECEIVED COMPLAINTS FROM CONSUMERS STATING THAT THEIR TAIL LIGHT ASSEMBLY IS NOT PROPERLY ILLUMINATING.THE TAIL LIGHT ASSEMBLY CONSISTS OF A TURN SIGNAL LAMP, A TAIL LAMP AND A BRAKE LAMP.THE COMPLAINANTS HAVE INDICATED THAT THE ISSUE IS WITH AN 8 PIN CONNECTOR AND ASSOCIATED GROUND WIRING.THESE COMPONENTS ARE ALLEGEDLY OVERHEATING AND MELTING DUE TO EXCESSIVE ELECTRICAL CURRENT THAT RUNS THROUGH THE SYSTEM.BMW ISSUED A TECHNICAL SERVICE BULLETIN (TSB) SIB-630306 ON FEBRUARY 2007 TO ADDRESS THE CONDITION BY ADDING SUPPLEMENTARY GROUND WIRING TO THE TAIL LAMP ASSEMBLY.ODI IS UPGRADING TO AN EA TO FURTHER INVESTIGATE THE ISSUE.
Exterior Lighting:brake Lights
ODI HAS RECEIVED COMPLAINTS FROM CONSUMERS STATING THAT THEIR TAIL LIGHT ASSEMBLY IS NOT PROPERLY ILLUMINATING.THE TAIL LIGHT ASSEMBLY CONSISTS OF A TURN SIGNAL LAMP, A TAIL LAMP AND A BRAKE LAMP.THE COMPLAINANTS HAVE INDICATED THAT THE ISSUE IS WITH AN 8 PIN CONNECTOR AND ASSOCIATED GROUND WIRING.THESE COMPONENTS ARE ALLEGEDLY OVERHEATING AND MELTING DUE TO EXCESSIVE ELECTRICAL CURRENT THAT RUNS THROUGH THE SYSTEM.BMW ISSUED A TECHNICAL SERVICE BULLETIN (TSB) SIB-630306 ON FEBRUARY 2007 TO ADDRESS THE CONDITION BY ADDING SUPPLEMENTARY GROUND WIRING TO THE TAIL LAMP ASSEMBLY.ODI IS UPGRADING TO AN EA TO FURTHER INVESTIGATE THE ISSUE.
Exterior Lighting:tail Lights
ODI HAS RECEIVED COMPLAINTS FROM CONSUMERS STATING THAT THEIR TAIL LIGHT ASSEMBLY IS NOT PROPERLY ILLUMINATING.THE TAIL LIGHT ASSEMBLY CONSISTS OF A TURN SIGNAL LAMP, A TAIL LAMP AND A BRAKE LAMP.THE COMPLAINANTS HAVE INDICATED THAT THE ISSUE IS WITH AN 8 PIN CONNECTOR AND ASSOCIATED GROUND WIRING.THESE COMPONENTS ARE ALLEGEDLY OVERHEATING AND MELTING DUE TO EXCESSIVE ELECTRICAL CURRENT THAT RUNS THROUGH THE SYSTEM.BMW ISSUED A TECHNICAL SERVICE BULLETIN (TSB) SIB-630306 ON FEBRUARY 2007 TO ADDRESS THE CONDITION BY ADDING SUPPLEMENTARY GROUND WIRING TO THE TAIL LAMP ASSEMBLY.ODI IS UPGRADING TO AN EA TO FURTHER INVESTIGATE THE ISSUE.
Exterior Lighting:turn Signal
ODI HAS RECEIVED COMPLAINTS FROM CONSUMERS STATING THAT THEIR TAIL LIGHT ASSEMBLY IS NOT PROPERLY ILLUMINATING.THE TAIL LIGHT ASSEMBLY CONSISTS OF A TURN SIGNAL LAMP, A TAIL LAMP AND A BRAKE LAMP.THE COMPLAINANTS HAVE INDICATED THAT THE ISSUE IS WITH AN 8 PIN CONNECTOR AND ASSOCIATED GROUND WIRING.THESE COMPONENTS ARE ALLEGEDLY OVERHEATING AND MELTING DUE TO EXCESSIVE ELECTRICAL CURRENT THAT RUNS THROUGH THE SYSTEM.BMW ISSUED A TECHNICAL SERVICE BULLETIN (TSB) SIB-630306 ON FEBRUARY 2007 TO ADDRESS THE CONDITION BY ADDING SUPPLEMENTARY GROUND WIRING TO THE TAIL LAMP ASSEMBLY.ODI IS UPGRADING TO AN EA TO FURTHER INVESTIGATE THE ISSUE.
DP09002 · Rear Lamp Illumination
Opened Apr 8, 2009 · Closed Aug 6, 2009
Status: closed (inferred from source dates) · Exterior Lighting; Exterior Lighting:back Up Lights; Exterior Lighting:brake Lights; Exterior Lighting:tail Lights; Exterior Lighting:turn Signal
IN MARCH 2009, THE OFFICE OF DEFECTS INVESTIGATION (ODI) RECEIVED A PETITION FROM MR. MARK PETERS REQUESTING AN INVESTIGATION OF REAR LAMP FAILURE IN MODEL YEAR 2002-2005 BMW 3-SERIES VEHICLES.AN INFORMATION REQUEST LETTER WAS SENT TO BMW IN APRIL 2009, AND ODI RECEIVED BMW'S RESPONSE IN JUNE 2009.THE TAIL LAMP ASSEMBLY CONTAINS LIGHTING FOR THE BRAKE LAMPS, TAIL LAMPS, AND TURN SIGNALS.A TECHNICAL SERVICE BULLETIN (TSB) WAS ISSUED BY BMW IN JANUARY OF 2007 INSTRUCTING SERVICE TECHNICIANS TO EXAMINE AN 8 PIN ELECTRICAL CONNECTOR FOR HEAT-RELATED DAMAGE AND TO INCORPORATE ADDITIONAL GROUND WIRING TO THE CONNECTOR.COMPLAINANTS HAVE ALLEGED THAT SIGNIFICANT THERMAL DAMAGE TO THE CONNECTOR AND ASSOCIATED GROUND WIRING HAS OCCURRED.THIS CONDITION CAN RESULT IN INTERMITTENT OR TOTAL LOSS OF ALL LIGHTING (BRAKE, TAIL, AND TURN SIGNAL) FOR THE EFFECTED REAR LAMP ASSEMBLY.ODI WILL OPEN A PRELIMINARY EVALUATION TO FURTHER EXAMINE THIS ISSUE INCLUDING FURTHER EVALUATING BMW COMPLAINTS AND RELATED WARRANTY DATA.
Additional source detail variants (5)
Exterior Lighting:back Up Lights
IN MARCH 2009, THE OFFICE OF DEFECTS INVESTIGATION (ODI) RECEIVED A PETITION FROM MR. MARK PETERS REQUESTING AN INVESTIGATION OF REAR LAMP FAILURE IN MODEL YEAR 2002-2005 BMW 3-SERIES VEHICLES.AN INFORMATION REQUEST LETTER WAS SENT TO BMW IN APRIL 2009, AND ODI RECEIVED BMW'S RESPONSE IN JUNE 2009.THE TAIL LAMP ASSEMBLY CONTAINS LIGHTING FOR THE BRAKE LAMPS, TAIL LAMPS, AND TURN SIGNALS.A TECHNICAL SERVICE BULLETIN (TSB) WAS ISSUED BY BMW IN JANUARY OF 2007 INSTRUCTING SERVICE TECHNICIANS TO EXAMINE AN 8 PIN ELECTRICAL CONNECTOR FOR HEAT-RELATED DAMAGE AND TO INCORPORATE ADDITIONAL GROUND WIRING TO THE CONNECTOR.COMPLAINANTS HAVE ALLEGED THAT SIGNIFICANT THERMAL DAMAGE TO THE CONNECTOR AND ASSOCIATED GROUND WIRING HAS OCCURRED.THIS CONDITION CAN RESULT IN INTERMITTENT OR TOTAL LOSS OF ALL LIGHTING (BRAKE, TAIL, AND TURN SIGNAL) FOR THE EFFECTED REAR LAMP ASSEMBLY.ODI WILL OPEN A PRELIMINARY EVALUATION TO FURTHER EXAMINE THIS ISSUE INCLUDING FURTHER EVALUATING BMW COMPLAINTS AND RELATED WARRANTY DATA.
Exterior Lighting
IN MARCH 2009, THE OFFICE OF DEFECTS INVESTIGATION (ODI) RECEIVED A PETITION FROM MR. MARK PETERS REQUESTING AN INVESTIGATION OF REAR LAMP FAILURE IN MODEL YEAR 2002-2005 BMW 3-SERIES VEHICLES.AN INFORMATION REQUEST LETTER WAS SENT TO BMW IN APRIL 2009, AND ODI RECEIVED BMW'S RESPONSE IN JUNE 2009.THE TAIL LAMP ASSEMBLY CONTAINS LIGHTING FOR THE BRAKE LAMPS, TAIL LAMPS, AND TURN SIGNALS.A TECHNICAL SERVICE BULLETIN (TSB) WAS ISSUED BY BMW IN JANUARY OF 2007 INSTRUCTING SERVICE TECHNICIANS TO EXAMINE AN 8 PIN ELECTRICAL CONNECTOR FOR HEAT-RELATED DAMAGE AND TO INCORPORATE ADDITIONAL GROUND WIRING TO THE CONNECTOR.COMPLAINANTS HAVE ALLEGED THAT SIGNIFICANT THERMAL DAMAGE TO THE CONNECTOR AND ASSOCIATED GROUND WIRING HAS OCCURRED.THIS CONDITION CAN RESULT IN INTERMITTENT OR TOTAL LOSS OF ALL LIGHTING (BRAKE, TAIL, AND TURN SIGNAL) FOR THE EFFECTED REAR LAMP ASSEMBLY.ODI WILL OPEN A PRELIMINARY EVALUATION TO FURTHER EXAMINE THIS ISSUE INCLUDING FURTHER EVALUATING BMW COMPLAINTS AND RELATED WARRANTY DATA.
Exterior Lighting:brake Lights
IN MARCH 2009, THE OFFICE OF DEFECTS INVESTIGATION (ODI) RECEIVED A PETITION FROM MR. MARK PETERS REQUESTING AN INVESTIGATION OF REAR LAMP FAILURE IN MODEL YEAR 2002-2005 BMW 3-SERIES VEHICLES.AN INFORMATION REQUEST LETTER WAS SENT TO BMW IN APRIL 2009, AND ODI RECEIVED BMW'S RESPONSE IN JUNE 2009.THE TAIL LAMP ASSEMBLY CONTAINS LIGHTING FOR THE BRAKE LAMPS, TAIL LAMPS, AND TURN SIGNALS.A TECHNICAL SERVICE BULLETIN (TSB) WAS ISSUED BY BMW IN JANUARY OF 2007 INSTRUCTING SERVICE TECHNICIANS TO EXAMINE AN 8 PIN ELECTRICAL CONNECTOR FOR HEAT-RELATED DAMAGE AND TO INCORPORATE ADDITIONAL GROUND WIRING TO THE CONNECTOR.COMPLAINANTS HAVE ALLEGED THAT SIGNIFICANT THERMAL DAMAGE TO THE CONNECTOR AND ASSOCIATED GROUND WIRING HAS OCCURRED.THIS CONDITION CAN RESULT IN INTERMITTENT OR TOTAL LOSS OF ALL LIGHTING (BRAKE, TAIL, AND TURN SIGNAL) FOR THE EFFECTED REAR LAMP ASSEMBLY.ODI WILL OPEN A PRELIMINARY EVALUATION TO FURTHER EXAMINE THIS ISSUE INCLUDING FURTHER EVALUATING BMW COMPLAINTS AND RELATED WARRANTY DATA.
Exterior Lighting:tail Lights
IN MARCH 2009, THE OFFICE OF DEFECTS INVESTIGATION (ODI) RECEIVED A PETITION FROM MR. MARK PETERS REQUESTING AN INVESTIGATION OF REAR LAMP FAILURE IN MODEL YEAR 2002-2005 BMW 3-SERIES VEHICLES.AN INFORMATION REQUEST LETTER WAS SENT TO BMW IN APRIL 2009, AND ODI RECEIVED BMW'S RESPONSE IN JUNE 2009.THE TAIL LAMP ASSEMBLY CONTAINS LIGHTING FOR THE BRAKE LAMPS, TAIL LAMPS, AND TURN SIGNALS.A TECHNICAL SERVICE BULLETIN (TSB) WAS ISSUED BY BMW IN JANUARY OF 2007 INSTRUCTING SERVICE TECHNICIANS TO EXAMINE AN 8 PIN ELECTRICAL CONNECTOR FOR HEAT-RELATED DAMAGE AND TO INCORPORATE ADDITIONAL GROUND WIRING TO THE CONNECTOR.COMPLAINANTS HAVE ALLEGED THAT SIGNIFICANT THERMAL DAMAGE TO THE CONNECTOR AND ASSOCIATED GROUND WIRING HAS OCCURRED.THIS CONDITION CAN RESULT IN INTERMITTENT OR TOTAL LOSS OF ALL LIGHTING (BRAKE, TAIL, AND TURN SIGNAL) FOR THE EFFECTED REAR LAMP ASSEMBLY.ODI WILL OPEN A PRELIMINARY EVALUATION TO FURTHER EXAMINE THIS ISSUE INCLUDING FURTHER EVALUATING BMW COMPLAINTS AND RELATED WARRANTY DATA.
Exterior Lighting:turn Signal
IN MARCH 2009, THE OFFICE OF DEFECTS INVESTIGATION (ODI) RECEIVED A PETITION FROM MR. MARK PETERS REQUESTING AN INVESTIGATION OF REAR LAMP FAILURE IN MODEL YEAR 2002-2005 BMW 3-SERIES VEHICLES.AN INFORMATION REQUEST LETTER WAS SENT TO BMW IN APRIL 2009, AND ODI RECEIVED BMW'S RESPONSE IN JUNE 2009.THE TAIL LAMP ASSEMBLY CONTAINS LIGHTING FOR THE BRAKE LAMPS, TAIL LAMPS, AND TURN SIGNALS.A TECHNICAL SERVICE BULLETIN (TSB) WAS ISSUED BY BMW IN JANUARY OF 2007 INSTRUCTING SERVICE TECHNICIANS TO EXAMINE AN 8 PIN ELECTRICAL CONNECTOR FOR HEAT-RELATED DAMAGE AND TO INCORPORATE ADDITIONAL GROUND WIRING TO THE CONNECTOR.COMPLAINANTS HAVE ALLEGED THAT SIGNIFICANT THERMAL DAMAGE TO THE CONNECTOR AND ASSOCIATED GROUND WIRING HAS OCCURRED.THIS CONDITION CAN RESULT IN INTERMITTENT OR TOTAL LOSS OF ALL LIGHTING (BRAKE, TAIL, AND TURN SIGNAL) FOR THE EFFECTED REAR LAMP ASSEMBLY.ODI WILL OPEN A PRELIMINARY EVALUATION TO FURTHER EXAMINE THIS ISSUE INCLUDING FURTHER EVALUATING BMW COMPLAINTS AND RELATED WARRANTY DATA.
2003 BMW 3 Series Problems, Complaints & Recalls | Skip That Year
Illustration