NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
4 reportsClear category filterMileage unknown · May 19, 2026
EngineFuel/propulsion SystemUnknown Or Other
Prior to August 2024, this vehicle operated with zero check engine lights or drivetrain faults. In August 2024, BMW of Pittsburgh executed federally mandated Safety Recall 23V-707, which required opening the cylinder head. Immediately following this service, the Check Engine Light began illuminating persistently.On or about Octo…
Read full complaint
Prior to August 2024, this vehicle operated with zero check engine lights or drivetrain faults. In August 2024, BMW of Pittsburgh executed federally mandated Safety Recall 23V-707, which required opening the cylinder head. Immediately following this service, the Check Engine Light began illuminating persistently.On or about October 3, 2024, an independent diagnostic scan at Bobby Rahal BMW pulled BMW Factory Code 002A89: Exhaust VANOS Camshaft Mechanism Fault (Mechanical Sticking/Flow Restriction). Technicians at Bobby Rahal BMW explicitly instructed me to return the car to BMW of Pittsburgh because they suspected the original VANOS safety recall repair was botched.On October 28, 2024, I returned the vehicle to BMW of Pittsburgh to address this issue. Their technicians opened the engine block assembly a second time, yet failed to correct the defect. Following this second visit, the check engine light continued to come on intermittently. The vehicle began suffering rough idling, difficulty starting, and dangerous stalling events during operation. Cycling the ignition on and off provided only temporary relief.The check engine light has now become permanently illuminated. The safety hazards have severely escalated into a protective engine "limp mode," causing violent drivetrain shuddering and a catastrophic loss of driveability. BMW of Pittsburgh refuses to honor the recall workmanship, demanding a predatory $6,000 out-of-pocket teardown fee to bypass their liability. The manufacturer (BMW North America) has been notified under Case Reference VH78028, but the safety defect remains unaddressed, and the vehicle is completely unsafe to drive.
NHTSA ODI #11738803
Mileage unknown · Mar 24, 2026
Engine
Due to BMW using plastic parts when you live in Hot and cold environments the plastic begins to mold to other plastic parts and pvc diaphragms tear rather easy causing rough idle , stalls and can cause over revving and send a car into another car while in gear. The cheap plastic cause oil leaks and when oil gets low cause engine…
Read full complaint
Due to BMW using plastic parts when you live in Hot and cold environments the plastic begins to mold to other plastic parts and pvc diaphragms tear rather easy causing rough idle , stalls and can cause over revving and send a car into another car while in gear. The cheap plastic cause oil leaks and when oil gets low cause engine failure as well.
NHTSA ODI #11726596
Mileage unknown · Mar 6, 2026
EngineFuel/propulsion System
On February 25, 2026, BMW of South Miami performed the VANOS safety recall repair on my vehicle. The repair order documented that VANOS bolts were missing and retrieved from the engine oil pan and that VANOS components were serviced. Within approximately 24–48 hours of picking up the vehicle, the check engine light illuminated …
Read full complaint
On February 25, 2026, BMW of South Miami performed the VANOS safety recall repair on my vehicle. The repair order documented that VANOS bolts were missing and retrieved from the engine oil pan and that VANOS components were serviced. Within approximately 24–48 hours of picking up the vehicle, the check engine light illuminated and the vehicle began operating abnormally, including rough idle and irregular shifting. The vehicle stored diagnostic fault code P054B (camshaft position timing over-retarded), which directly relates to camshaft timing and the VANOS system involved in the recall repair. I returned the vehicle to the dealership for further diagnosis. The dealership stated an aftermarket camshaft position sensor with two O-rings was installed and removed one O-ring to correct the gap between the sensor and the camshaft reluctor wheel. The faults were cleared and the vehicle was returned to me. However, the check engine light returned again the following morning upon cold start, indicating the issue was not corrected. My service advisor has since stated that replacing the camshaft position sensor is not part of the recall repair and the dealership has declined to repair the vehicle under the recall. Because the malfunction appeared immediately after the VANOS safety recall repair and involves the camshaft timing system connected to VANOS operation, I believe the recall repair may not have been properly completed or corrected. I am requesting that NHTSA review this matter as a potential recall effectiveness issue, as the safety recall repair appears unresolved and the vehicle continues to experience faults related to the system that was repaired.
NHTSA ODI #11722577
79,769 miles · Jun 16, 2022
Engine
The contact owns a 2012 BMW 128i. The contact stated after completing an oil change at the dealer and starting the vehicle, the RPM started fluctuating. The contact stated that after coming to a complete stop at a traffic light, the RPM fluctuated rapidly and the vehicle decelerated while driving. The dealer was notified of the …
Read full complaint
The contact owns a 2012 BMW 128i. The contact stated after completing an oil change at the dealer and starting the vehicle, the RPM started fluctuating. The contact stated that after coming to a complete stop at a traffic light, the RPM fluctuated rapidly and the vehicle decelerated while driving. The dealer was notified of the failure and advised the contact to take the vehicle back to the dealer for a diagnostic test. The contact was able to drive to the dealer at a slower speed. The dealer diagnosed that the VANOS (Variable Nockenwell Steuerung) system needed to be replaced. The dealer informed the contact that the failure was a manufacturing defect; however, she would be responsible for the cost of the repair. The manufacturer was notified of the failure and informed the contact that they could not assist since an unknown recall was converted to an extended warranty repair which had expired. The vehicle was not repaired. The failure mileage was 79,769.
NHTSA ODI #11469556
Official recalls
5Mar 2, 2022
BMW of North America, LLC (BMW) is recalling certain 2008-2013 1 Series Coupe (128i); 2007-2013 3 Series Coupe (328i, 328xi, 328i xDrive); 2007-2010 X3 SAV (X3 3.0si, X3 xDrive30i); 2008-2013 1 Series Convertible (128i); 2006-2011 3 Series Sedan (325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi); 2006-2012 3 Series Wagon (328i, 328i xDrive); 2007-2013 3 Series Convertible (328i); 2006-2010 5 Series Sedan (525i, 525xi, 528i, 528xi, 530i, 530xi); 2006-2007 5 Series Wagon (530xi); 2007-2010 X5 SAV (X5 3.0si, X5 xDrive30i); 2006-2008 Z4 Coupe (Z4 3.0si); and 2006-2011 Z4 Roadster (Z4 3.0i, Z4 3.0si, Z4 sDrive30i) vehicles. The heater for the positive crankcase ventilation (PCV) valve may short circuit.
Consequence & remedy
Consequence: An electrical short can cause the PCV valve heater to overheat, increasing the risk of a fire while driving or, soon after driving when parked.
Remedy: This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Dealers will install an electrical wiring harness with fuse protection for the PCV Valve heater in potentially affected vehicles, free of charge. This recall supersedes and expands previous NHTSA recalls 17V-683 and 19V-273. Vehicles previously repaired under the prior recalls will need to come back for the new recall remedy. The remedy is currently being developed. Interim owner notification letters informing owners of the safety risk were mailed on April 1, 2022. Owner notification letters were mailed on July 22, 2022. Owners may contact BMW customer service at 1-800-525-7417.
Jan 15, 2020
BMW of North America, LLC (BMW) is recalling certain 2008-2013 128i and 135i Convertibles, 128i, 135i, and M Coupes, 2007-2010 X3 30si and X3 xDrive30i, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i, 2007-2013 328i, 328i xDrive, 335i, 335is, 335i xDrive and M3 Coupes, 2006-2011 328i, 328xi, 328i xDrive, 325i, 325xi, 330i, 330xi, 335i, 335xi, 335i xDrive and M3, 2009-2011 335D, 2006-2012 325xi, 328i, 328xi and 328i xDrive, 2010-2011 X6 ActiveHybrid, 2007-2013 328i, 335i, 335is, M3 Coupes, X5 30si, X5 xDrive30i, X5 xDrive35i, X5 48i, X5 xDrive48i, X5 xDrive50i and X5 M, 2009-2013 X5 xDrive35d and 2008-2014 X6 xDrive35i, X6 xDrive50i and X6M vehicles equipped with non-desiccated driver frontal air bag inflators containing phase stabilized ammonium nitrate (PSAN) that were used as interim remedy parts for previous Takata recalls. These inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, high temperatures, and high temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver air bag. On X5 and X6 vehicles, only the inflator will be replaced. All repairs will be performed free of charge. The recall began March 11, 2020. Owners may contact BMW customer service at 1-800-525-7417.
Aug 6, 2019
BMW of North America, LLC (BMW) is recalling certain 2008-2012 BMW 128i, 135i, 135is Coupes and 128i, 135i Convertible vehicles. The wiring and electrical connectors in the blower-regulator wiring harness may overheat.
Consequence & remedy
Consequence: Wiring that overheats could cause the electrical connectors to melt, and increase the risk of a fire, even when the vehicle is unattended.
Remedy: BMW will notify owners, and dealers will inspect the blower-regulator wiring harness, and replace it with a new part, free of charge. The recall began October 4, 2019. Owners may contact BMW customer service at 1-800-525-7417. Note: This recall is an expansion of an earlier recall number 17V-676.
Feb 5, 2016
BMW of North America, LLC (BMW) is recalling certain model year 2008-2013 128i and 135i coupes and convertibles and 1 Series M coupes, 2006-2011 325i, 325xi, 328i, 328xi, 328i xDrive, 330i, 330xi, 335i, 335xi, 335i xDrive Sedans, 2009-2011 335d sedans, 2006-2012 325xiT, 328i and 328xi sports wagons, 2007-2013 328i, 328xi, 328i xDrive, 335i, 335xi, 335i xDrive, 335is and M3 Coupes and Convertibles, 2013-2015 X1 sDrive28i, X1 xDrive28i and X1 xDrive35i SAVs, 2007-2010 X3 xDrive30i SAVs, 2007-2013 X5 xDrive30i, X5 xDrive35i, X5 xDrive48i, X5 xDrive50i and X5 M SAVs, 2009-2013 BMW X5 xDrive35d SAVs, 2008-2014 X6 xDrive35i, X6 xDrive50i, and X6 M SACs, 2010-2011 BMW X6 xDrive50i SACs and 2008-2011 M3 Sedan vehicles. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: BMW will notify owners, and dealers will replace the driver's frontal air bag module or inflator depending on the vehicle model, free of charge. The recall began March 9, 2018. Owners may contact BMW customer service at 1-800-525-7417.
Feb 7, 2013
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence & remedy
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Additional source detail variants (3)
Electrical System:wiring:fuses And Circuit Breakers
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Electrical SYSTEM:12V/24V/48V Battery:cables
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Electrical System
BMW is recalling certain model year 2008-2012 1-Series coupes and convertibles manufactured December 2007 through September 2011; and 2007-2011 3-Series coupes and convertibles manufactured March 2007 through October 2011; 2007-2011 3-Series sedans manufactured March 2007 through October 2011; 2007-2011 3-Series sports wagons manufactured March 2007 through June 2011; and 2009-2011 Z4 vehicles manufactured March 2009 through June 2011. In February 2013, BMW recalled 504,545 vehicles. In July 2013, BMW informed the agency that it was adding 1-Series, 3-Series, and Z4 vehicles, representing an additional 12,094 vehicles. The total number of vehicles being recalled is now 516,791. The connector for the positive battery cable connector and the corresponding terminal on the fuse box may degrade over time. Over time, the high current flow and heat from electrical resistance may lead to a breakage of the connection, and a loss of electrical power to the vehicle.
Consequence: If there is a loss of electrical power to the vehicle, the vehicle may unexpectedly stall, increasing the risk of a crash.
Remedy: BMW will notify owners, and dealers will replace the positive battery cable connector and secure it with an improved method, free of charge. The recall began on March 13, 2013. Owners may call BMW at 1-800-525-7417 or email BMW at CustomerRelations@bmwusa.com.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration