2019 Autocar Xpeditor

Electrical System: Instrument Cluster/panel

Autocar, LLC (Autocar) is recalling certain 2019-2021 Xpeditor and 2021-2022 Legend vehicles equipped with a MRS 7" display. The display may restart during operation, resulting in the warning lights not being visible until the restart is completed. The display may restart during operation and the warning icons for the Seat Belt, Low Air, Check Engine, ABS, Park Brake Applied, Turn Signal Indicator, Fuel Level, Electrical Charge, Coolant Temperature and Oil Pressure will not be visible until restart has completed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Control and Displays."

Consequence: During a display restart, warning lights such as the seat belt, check engine, fuel level, and other important warnings may not display, increasing the risk of a crash or injury.

Remedy: Autocar will notify owners, and dealers will replace the display, free of charge. Interim notices informing owners of the safety risk were mailed April 19, 2021. A second notice will be sent when the remedy becomes available in February 2022. Owners may contact Autocar customer service at 1-888-218-3611 or 1-877-973-3486. Autocar's number for this recall is ACX-2102- DC-2101.

Seat Belts:front:warning Light/devices

Autocar, LLC (Autocar) is recalling certain 2019-2021 Xpeditor and 2021-2022 Legend vehicles equipped with a MRS 7" display. The display may restart during operation, resulting in the warning lights not being visible until the restart is completed. The display may restart during operation and the warning icons for the Seat Belt, Low Air, Check Engine, ABS, Park Brake Applied, Turn Signal Indicator, Fuel Level, Electrical Charge, Coolant Temperature and Oil Pressure will not be visible until restart has completed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Control and Displays."

Consequence: During a display restart, warning lights such as the seat belt, check engine, fuel level, and other important warnings may not display, increasing the risk of a crash or injury.

Remedy: Autocar will notify owners, and dealers will replace the display, free of charge. Interim notices informing owners of the safety risk were mailed April 19, 2021. A second notice will be sent when the remedy becomes available in February 2022. Owners may contact Autocar customer service at 1-888-218-3611 or 1-877-973-3486. Autocar's number for this recall is ACX-2102- DC-2101.

Parking Brake:indicator Light

Autocar, LLC (Autocar) is recalling certain 2019-2021 Xpeditor and 2021-2022 Legend vehicles equipped with a MRS 7" display. The display may restart during operation, resulting in the warning lights not being visible until the restart is completed. The display may restart during operation and the warning icons for the Seat Belt, Low Air, Check Engine, ABS, Park Brake Applied, Turn Signal Indicator, Fuel Level, Electrical Charge, Coolant Temperature and Oil Pressure will not be visible until restart has completed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Control and Displays."

Consequence: During a display restart, warning lights such as the seat belt, check engine, fuel level, and other important warnings may not display, increasing the risk of a crash or injury.

Remedy: Autocar will notify owners, and dealers will replace the display, free of charge. Interim notices informing owners of the safety risk were mailed April 19, 2021. A second notice will be sent when the remedy becomes available in February 2022. Owners may contact Autocar customer service at 1-888-218-3611 or 1-877-973-3486. Autocar's number for this recall is ACX-2102- DC-2101.

Service Brakes, Hydraulic:antilock/traction Control/electronic Limited Slip:abs Warning Light

Autocar, LLC (Autocar) is recalling certain 2019-2021 Xpeditor and 2021-2022 Legend vehicles equipped with a MRS 7" display. The display may restart during operation, resulting in the warning lights not being visible until the restart is completed. The display may restart during operation and the warning icons for the Seat Belt, Low Air, Check Engine, ABS, Park Brake Applied, Turn Signal Indicator, Fuel Level, Electrical Charge, Coolant Temperature and Oil Pressure will not be visible until restart has completed. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 101, "Control and Displays."

Consequence: During a display restart, warning lights such as the seat belt, check engine, fuel level, and other important warnings may not display, increasing the risk of a crash or injury.

Remedy: Autocar will notify owners, and dealers will replace the display, free of charge. Interim notices informing owners of the safety risk were mailed April 19, 2021. A second notice will be sent when the remedy becomes available in February 2022. Owners may contact Autocar customer service at 1-888-218-3611 or 1-877-973-3486. Autocar's number for this recall is ACX-2102- DC-2101.

Engine

Autocar, LLC (Autocar) is recalling certain 2018-2021 Xpeditor vehicles. The turbocharger heat shield may fail and detach from the vehicle.

Consequence: A detached heat shield can become a road hazard, increasing the risk of a crash or injury.

Remedy: Autocar will notify owners, and dealers will replace the turbocharger heat shield, free of charge. Owner notification letters were mailed on June 24, 2021. Owners may contact Autocar customer service at 1-888-218-3611 or 1-877-973-3486. Autocar's number for this recall is ACX-2103.

Engine And Engine Cooling:engine:gasoline:turbo/supercharger

Autocar, LLC (Autocar) is recalling certain 2018-2021 Xpeditor vehicles. The turbocharger heat shield may fail and detach from the vehicle.

Consequence: A detached heat shield can become a road hazard, increasing the risk of a crash or injury.

Remedy: Autocar will notify owners, and dealers will replace the turbocharger heat shield, free of charge. Owner notification letters were mailed on June 24, 2021. Owners may contact Autocar customer service at 1-888-218-3611 or 1-877-973-3486. Autocar's number for this recall is ACX-2103.

Parking Brake

On April 1, 2020, following information received from the Office of Defects Investigation (ODI) network of fleet contacts, ODI opened PE20-003 to investigate reports of vehicle roll away in certain model year (MY) 2008-2020 Autocar and Mack refuse trucks equipped with certain Bendix PP-1 push-pull pneumatic park brake control valves with a pipe-away exhaust configuration. Prior to ODI’s investigation,[KK(1]  Bendix Commercial Vehicle Systems LLC (Bendix), the subject component manufacturer, published two related technical service bulletins (TSBs): Bendix Push-Pull Type Control Valves Service Data SD-03-3611 Rev. 007 (2019-03) and Bendix PP-1 & PP-8 Park Control Valve Wear and Replacement Notice Technical Bulletin TCH-003-056 (2019-11-20). ODI sent Information Request (IR) letters to motor vehicle manufacturers Autocar LLC (Autocar) and Volvo Trucks North America/Mack Trucks, Inc. (Volvo/Mack) and motor vehicle equipment manufacturer Bendix. IR response data from all three manufacturers was analyzed and cross-referenced to gain further understanding. To date, ODI is aware of 5 vehicle roll-away incidents related to the alleged defect condition in the subject vehicles equipped with the subject components, resulting in 4 crashes and 1 injury. On December 9, 2021, Volvo/Mack notified the agency of a safety recall (21V953) to address a safety defect in certain MY 2008-2019 TerraPro (MRU) and MY 2019-2022 TerraPro (TE) trucks originally equipped with the subject components. [KK(2] On January 1, 2023, Autocar notified the agency of a safety recall (23V023) to address a safety defect in certain MY 2008-2020 ACX (Xpeditor), MY 2012-2020 ACMD (Xpert), MY 2010-2020 ACTT (Xspotter), MY 2008-2010 WX and MY 2008-2010 WXLL trucks. Volvo/Mack and Autocar's recall remedies involve removing the vent line fitting threaded into the exhaust port of the subject PP-1 valve. [VD(3] Both Autocar and Mack have stopped equipping new refuse trucks with park control valves using the exhaust pipe-away configuration. After discussions between ODI and Bendix concerning ways to prevent new PP-1 valves from being sold and installed with a potential for the exhaust to become restricted, Bendix will take the following actions: 1) issue a letter to all original equipment (OE) customers with important safety information warning them about the safety risk of attaching plumbing to the exhaust port when the subject component is used as a park control valve; and 2) affix a warning label on all aftermarket parts warning not to install pipe-away exhaust port plumbing. In view of the recalls being conducted by Volvo/Mack and Autocar, and the actions taken by Bendix, ODI has closed this Preliminary Evaluation. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist in equipment or other model or MY vehicles that have not been recalled. The agency reserves the right to take further action if warranted.

Parking Brake

On April 1, 2020, following information received from the Office of Defects Investigation (ODI) network of fleet contacts, ODI opened PE20-003 to investigate reports of vehicle roll away in certain model year (MY) 2008-2020 Autocar and Mack refuse trucks equipped with certain Bendix PP-1 push-pull pneumatic park brake control valves with a pipe-away exhaust configuration. Prior to ODI’s investigation,[KK(1]  Bendix Commercial Vehicle Systems LLC (Bendix), the subject component manufacturer, published two related technical service bulletins (TSBs): Bendix Push-Pull Type Control Valves Service Data SD-03-3611 Rev. 007 (2019-03) and Bendix PP-1 & PP-8 Park Control Valve Wear and Replacement Notice Technical Bulletin TCH-003-056 (2019-11-20). ODI sent Information Request (IR) letters to motor vehicle manufacturers Autocar LLC (Autocar) and Volvo Trucks North America/Mack Trucks, Inc. (Volvo/Mack) and motor vehicle equipment manufacturer Bendix. IR response data from all three manufacturers was analyzed and cross-referenced to gain further understanding. To date, ODI is aware of 5 vehicle roll-away incidents related to the alleged defect condition in the subject vehicles equipped with the subject components, resulting in 4 crashes and 1 injury. On December 9, 2021, Volvo/Mack notified the agency of a safety recall (21V953) to address a safety defect in certain MY 2008-2019 TerraPro (MRU) and MY 2019-2022 TerraPro (TE) trucks originally equipped with the subject components. [KK(2] On January 1, 2023, Autocar notified the agency of a safety recall (23V023) to address a safety defect in certain MY 2008-2020 ACX (Xpeditor), MY 2012-2020 ACMD (Xpert), MY 2010-2020 ACTT (Xspotter), MY 2008-2010 WX and MY 2008-2010 WXLL trucks. Volvo/Mack and Autocar's recall remedies involve removing the vent line fitting threaded into the exhaust port of the subject PP-1 valve. [VD(3] Both Autocar and Mack have stopped equipping new refuse trucks with park control valves using the exhaust pipe-away configuration. After discussions between ODI and Bendix concerning ways to prevent new PP-1 valves from being sold and installed with a potential for the exhaust to become restricted, Bendix will take the following actions: 1) issue a letter to all original equipment (OE) customers with important safety information warning them about the safety risk of attaching plumbing to the exhaust port when the subject component is used as a park control valve; and 2) affix a warning label on all aftermarket parts warning not to install pipe-away exhaust port plumbing. In view of the recalls being conducted by Volvo/Mack and Autocar, and the actions taken by Bendix, ODI has closed this Preliminary Evaluation. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist in equipment or other model or MY vehicles that have not been recalled. The agency reserves the right to take further action if warranted.

Parking Brake:conventional:air

On April 1, 2020, following information received from the Office of Defects Investigation (ODI) network of fleet contacts, ODI opened PE20-003 to investigate reports of vehicle roll away in certain model year (MY) 2008-2020 Autocar and Mack refuse trucks equipped with certain Bendix PP-1 push-pull pneumatic park brake control valves with a pipe-away exhaust configuration. Prior to ODI’s investigation,[KK(1]  Bendix Commercial Vehicle Systems LLC (Bendix), the subject component manufacturer, published two related technical service bulletins (TSBs): Bendix Push-Pull Type Control Valves Service Data SD-03-3611 Rev. 007 (2019-03) and Bendix PP-1 & PP-8 Park Control Valve Wear and Replacement Notice Technical Bulletin TCH-003-056 (2019-11-20). ODI sent Information Request (IR) letters to motor vehicle manufacturers Autocar LLC (Autocar) and Volvo Trucks North America/Mack Trucks, Inc. (Volvo/Mack) and motor vehicle equipment manufacturer Bendix. IR response data from all three manufacturers was analyzed and cross-referenced to gain further understanding. To date, ODI is aware of 5 vehicle roll-away incidents related to the alleged defect condition in the subject vehicles equipped with the subject components, resulting in 4 crashes and 1 injury. On December 9, 2021, Volvo/Mack notified the agency of a safety recall (21V953) to address a safety defect in certain MY 2008-2019 TerraPro (MRU) and MY 2019-2022 TerraPro (TE) trucks originally equipped with the subject components. [KK(2] On January 1, 2023, Autocar notified the agency of a safety recall (23V023) to address a safety defect in certain MY 2008-2020 ACX (Xpeditor), MY 2012-2020 ACMD (Xpert), MY 2010-2020 ACTT (Xspotter), MY 2008-2010 WX and MY 2008-2010 WXLL trucks. Volvo/Mack and Autocar's recall remedies involve removing the vent line fitting threaded into the exhaust port of the subject PP-1 valve. [VD(3] Both Autocar and Mack have stopped equipping new refuse trucks with park control valves using the exhaust pipe-away configuration. After discussions between ODI and Bendix concerning ways to prevent new PP-1 valves from being sold and installed with a potential for the exhaust to become restricted, Bendix will take the following actions: 1) issue a letter to all original equipment (OE) customers with important safety information warning them about the safety risk of attaching plumbing to the exhaust port when the subject component is used as a park control valve; and 2) affix a warning label on all aftermarket parts warning not to install pipe-away exhaust port plumbing. In view of the recalls being conducted by Volvo/Mack and Autocar, and the actions taken by Bendix, ODI has closed this Preliminary Evaluation. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist in equipment or other model or MY vehicles that have not been recalled. The agency reserves the right to take further action if warranted.

Parking Brake:conventional:air

On April 1, 2020, following information received from the Office of Defects Investigation (ODI) network of fleet contacts, ODI opened PE20-003 to investigate reports of vehicle roll away in certain model year (MY) 2008-2020 Autocar and Mack refuse trucks equipped with certain Bendix PP-1 push-pull pneumatic park brake control valves with a pipe-away exhaust configuration. Prior to ODI’s investigation,[KK(1]  Bendix Commercial Vehicle Systems LLC (Bendix), the subject component manufacturer, published two related technical service bulletins (TSBs): Bendix Push-Pull Type Control Valves Service Data SD-03-3611 Rev. 007 (2019-03) and Bendix PP-1 & PP-8 Park Control Valve Wear and Replacement Notice Technical Bulletin TCH-003-056 (2019-11-20). ODI sent Information Request (IR) letters to motor vehicle manufacturers Autocar LLC (Autocar) and Volvo Trucks North America/Mack Trucks, Inc. (Volvo/Mack) and motor vehicle equipment manufacturer Bendix. IR response data from all three manufacturers was analyzed and cross-referenced to gain further understanding. To date, ODI is aware of 5 vehicle roll-away incidents related to the alleged defect condition in the subject vehicles equipped with the subject components, resulting in 4 crashes and 1 injury. On December 9, 2021, Volvo/Mack notified the agency of a safety recall (21V953) to address a safety defect in certain MY 2008-2019 TerraPro (MRU) and MY 2019-2022 TerraPro (TE) trucks originally equipped with the subject components. [KK(2] On January 1, 2023, Autocar notified the agency of a safety recall (23V023) to address a safety defect in certain MY 2008-2020 ACX (Xpeditor), MY 2012-2020 ACMD (Xpert), MY 2010-2020 ACTT (Xspotter), MY 2008-2010 WX and MY 2008-2010 WXLL trucks. Volvo/Mack and Autocar's recall remedies involve removing the vent line fitting threaded into the exhaust port of the subject PP-1 valve. [VD(3] Both Autocar and Mack have stopped equipping new refuse trucks with park control valves using the exhaust pipe-away configuration. After discussions between ODI and Bendix concerning ways to prevent new PP-1 valves from being sold and installed with a potential for the exhaust to become restricted, Bendix will take the following actions: 1) issue a letter to all original equipment (OE) customers with important safety information warning them about the safety risk of attaching plumbing to the exhaust port when the subject component is used as a park control valve; and 2) affix a warning label on all aftermarket parts warning not to install pipe-away exhaust port plumbing. In view of the recalls being conducted by Volvo/Mack and Autocar, and the actions taken by Bendix, ODI has closed this Preliminary Evaluation. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist in equipment or other model or MY vehicles that have not been recalled. The agency reserves the right to take further action if warranted.

Service Brakes, Air:controls

On April 1, 2020, following information received from the Office of Defects Investigation (ODI) network of fleet contacts, ODI opened PE20-003 to investigate reports of vehicle roll away in certain model year (MY) 2008-2020 Autocar and Mack refuse trucks equipped with certain Bendix PP-1 push-pull pneumatic park brake control valves with a pipe-away exhaust configuration. Prior to ODI’s investigation,[KK(1]  Bendix Commercial Vehicle Systems LLC (Bendix), the subject component manufacturer, published two related technical service bulletins (TSBs): Bendix Push-Pull Type Control Valves Service Data SD-03-3611 Rev. 007 (2019-03) and Bendix PP-1 & PP-8 Park Control Valve Wear and Replacement Notice Technical Bulletin TCH-003-056 (2019-11-20). ODI sent Information Request (IR) letters to motor vehicle manufacturers Autocar LLC (Autocar) and Volvo Trucks North America/Mack Trucks, Inc. (Volvo/Mack) and motor vehicle equipment manufacturer Bendix. IR response data from all three manufacturers was analyzed and cross-referenced to gain further understanding. To date, ODI is aware of 5 vehicle roll-away incidents related to the alleged defect condition in the subject vehicles equipped with the subject components, resulting in 4 crashes and 1 injury. On December 9, 2021, Volvo/Mack notified the agency of a safety recall (21V953) to address a safety defect in certain MY 2008-2019 TerraPro (MRU) and MY 2019-2022 TerraPro (TE) trucks originally equipped with the subject components. [KK(2] On January 1, 2023, Autocar notified the agency of a safety recall (23V023) to address a safety defect in certain MY 2008-2020 ACX (Xpeditor), MY 2012-2020 ACMD (Xpert), MY 2010-2020 ACTT (Xspotter), MY 2008-2010 WX and MY 2008-2010 WXLL trucks. Volvo/Mack and Autocar's recall remedies involve removing the vent line fitting threaded into the exhaust port of the subject PP-1 valve. [VD(3] Both Autocar and Mack have stopped equipping new refuse trucks with park control valves using the exhaust pipe-away configuration. After discussions between ODI and Bendix concerning ways to prevent new PP-1 valves from being sold and installed with a potential for the exhaust to become restricted, Bendix will take the following actions: 1) issue a letter to all original equipment (OE) customers with important safety information warning them about the safety risk of attaching plumbing to the exhaust port when the subject component is used as a park control valve; and 2) affix a warning label on all aftermarket parts warning not to install pipe-away exhaust port plumbing. In view of the recalls being conducted by Volvo/Mack and Autocar, and the actions taken by Bendix, ODI has closed this Preliminary Evaluation. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist in equipment or other model or MY vehicles that have not been recalled. The agency reserves the right to take further action if warranted.

Service Brakes, Air:controls

On April 1, 2020, following information received from the Office of Defects Investigation (ODI) network of fleet contacts, ODI opened PE20-003 to investigate reports of vehicle roll away in certain model year (MY) 2008-2020 Autocar and Mack refuse trucks equipped with certain Bendix PP-1 push-pull pneumatic park brake control valves with a pipe-away exhaust configuration. Prior to ODI’s investigation,[KK(1]  Bendix Commercial Vehicle Systems LLC (Bendix), the subject component manufacturer, published two related technical service bulletins (TSBs): Bendix Push-Pull Type Control Valves Service Data SD-03-3611 Rev. 007 (2019-03) and Bendix PP-1 & PP-8 Park Control Valve Wear and Replacement Notice Technical Bulletin TCH-003-056 (2019-11-20). ODI sent Information Request (IR) letters to motor vehicle manufacturers Autocar LLC (Autocar) and Volvo Trucks North America/Mack Trucks, Inc. (Volvo/Mack) and motor vehicle equipment manufacturer Bendix. IR response data from all three manufacturers was analyzed and cross-referenced to gain further understanding. To date, ODI is aware of 5 vehicle roll-away incidents related to the alleged defect condition in the subject vehicles equipped with the subject components, resulting in 4 crashes and 1 injury. On December 9, 2021, Volvo/Mack notified the agency of a safety recall (21V953) to address a safety defect in certain MY 2008-2019 TerraPro (MRU) and MY 2019-2022 TerraPro (TE) trucks originally equipped with the subject components. [KK(2] On January 1, 2023, Autocar notified the agency of a safety recall (23V023) to address a safety defect in certain MY 2008-2020 ACX (Xpeditor), MY 2012-2020 ACMD (Xpert), MY 2010-2020 ACTT (Xspotter), MY 2008-2010 WX and MY 2008-2010 WXLL trucks. Volvo/Mack and Autocar's recall remedies involve removing the vent line fitting threaded into the exhaust port of the subject PP-1 valve. [VD(3] Both Autocar and Mack have stopped equipping new refuse trucks with park control valves using the exhaust pipe-away configuration. After discussions between ODI and Bendix concerning ways to prevent new PP-1 valves from being sold and installed with a potential for the exhaust to become restricted, Bendix will take the following actions: 1) issue a letter to all original equipment (OE) customers with important safety information warning them about the safety risk of attaching plumbing to the exhaust port when the subject component is used as a park control valve; and 2) affix a warning label on all aftermarket parts warning not to install pipe-away exhaust port plumbing. In view of the recalls being conducted by Volvo/Mack and Autocar, and the actions taken by Bendix, ODI has closed this Preliminary Evaluation. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist in equipment or other model or MY vehicles that have not been recalled. The agency reserves the right to take further action if warranted.

Service Brakes, Air:supply:hoses, Lines/piping, And Fittings

On April 1, 2020, following information received from the Office of Defects Investigation (ODI) network of fleet contacts, ODI opened PE20-003 to investigate reports of vehicle roll away in certain model year (MY) 2008-2020 Autocar and Mack refuse trucks equipped with certain Bendix PP-1 push-pull pneumatic park brake control valves with a pipe-away exhaust configuration. Prior to ODI’s investigation,[KK(1]  Bendix Commercial Vehicle Systems LLC (Bendix), the subject component manufacturer, published two related technical service bulletins (TSBs): Bendix Push-Pull Type Control Valves Service Data SD-03-3611 Rev. 007 (2019-03) and Bendix PP-1 & PP-8 Park Control Valve Wear and Replacement Notice Technical Bulletin TCH-003-056 (2019-11-20). ODI sent Information Request (IR) letters to motor vehicle manufacturers Autocar LLC (Autocar) and Volvo Trucks North America/Mack Trucks, Inc. (Volvo/Mack) and motor vehicle equipment manufacturer Bendix. IR response data from all three manufacturers was analyzed and cross-referenced to gain further understanding. To date, ODI is aware of 5 vehicle roll-away incidents related to the alleged defect condition in the subject vehicles equipped with the subject components, resulting in 4 crashes and 1 injury. On December 9, 2021, Volvo/Mack notified the agency of a safety recall (21V953) to address a safety defect in certain MY 2008-2019 TerraPro (MRU) and MY 2019-2022 TerraPro (TE) trucks originally equipped with the subject components. [KK(2] On January 1, 2023, Autocar notified the agency of a safety recall (23V023) to address a safety defect in certain MY 2008-2020 ACX (Xpeditor), MY 2012-2020 ACMD (Xpert), MY 2010-2020 ACTT (Xspotter), MY 2008-2010 WX and MY 2008-2010 WXLL trucks. Volvo/Mack and Autocar's recall remedies involve removing the vent line fitting threaded into the exhaust port of the subject PP-1 valve. [VD(3] Both Autocar and Mack have stopped equipping new refuse trucks with park control valves using the exhaust pipe-away configuration. After discussions between ODI and Bendix concerning ways to prevent new PP-1 valves from being sold and installed with a potential for the exhaust to become restricted, Bendix will take the following actions: 1) issue a letter to all original equipment (OE) customers with important safety information warning them about the safety risk of attaching plumbing to the exhaust port when the subject component is used as a park control valve; and 2) affix a warning label on all aftermarket parts warning not to install pipe-away exhaust port plumbing. In view of the recalls being conducted by Volvo/Mack and Autocar, and the actions taken by Bendix, ODI has closed this Preliminary Evaluation. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist in equipment or other model or MY vehicles that have not been recalled. The agency reserves the right to take further action if warranted.

Service Brakes, Air:supply:hoses, Lines/piping, And Fittings

On April 1, 2020, following information received from the Office of Defects Investigation (ODI) network of fleet contacts, ODI opened PE20-003 to investigate reports of vehicle roll away in certain model year (MY) 2008-2020 Autocar and Mack refuse trucks equipped with certain Bendix PP-1 push-pull pneumatic park brake control valves with a pipe-away exhaust configuration. Prior to ODI’s investigation,[KK(1]  Bendix Commercial Vehicle Systems LLC (Bendix), the subject component manufacturer, published two related technical service bulletins (TSBs): Bendix Push-Pull Type Control Valves Service Data SD-03-3611 Rev. 007 (2019-03) and Bendix PP-1 & PP-8 Park Control Valve Wear and Replacement Notice Technical Bulletin TCH-003-056 (2019-11-20). ODI sent Information Request (IR) letters to motor vehicle manufacturers Autocar LLC (Autocar) and Volvo Trucks North America/Mack Trucks, Inc. (Volvo/Mack) and motor vehicle equipment manufacturer Bendix. IR response data from all three manufacturers was analyzed and cross-referenced to gain further understanding. To date, ODI is aware of 5 vehicle roll-away incidents related to the alleged defect condition in the subject vehicles equipped with the subject components, resulting in 4 crashes and 1 injury. On December 9, 2021, Volvo/Mack notified the agency of a safety recall (21V953) to address a safety defect in certain MY 2008-2019 TerraPro (MRU) and MY 2019-2022 TerraPro (TE) trucks originally equipped with the subject components. [KK(2] On January 1, 2023, Autocar notified the agency of a safety recall (23V023) to address a safety defect in certain MY 2008-2020 ACX (Xpeditor), MY 2012-2020 ACMD (Xpert), MY 2010-2020 ACTT (Xspotter), MY 2008-2010 WX and MY 2008-2010 WXLL trucks. Volvo/Mack and Autocar's recall remedies involve removing the vent line fitting threaded into the exhaust port of the subject PP-1 valve. [VD(3] Both Autocar and Mack have stopped equipping new refuse trucks with park control valves using the exhaust pipe-away configuration. After discussions between ODI and Bendix concerning ways to prevent new PP-1 valves from being sold and installed with a potential for the exhaust to become restricted, Bendix will take the following actions: 1) issue a letter to all original equipment (OE) customers with important safety information warning them about the safety risk of attaching plumbing to the exhaust port when the subject component is used as a park control valve; and 2) affix a warning label on all aftermarket parts warning not to install pipe-away exhaust port plumbing. In view of the recalls being conducted by Volvo/Mack and Autocar, and the actions taken by Bendix, ODI has closed this Preliminary Evaluation. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist in equipment or other model or MY vehicles that have not been recalled. The agency reserves the right to take further action if warranted.