NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
66 reports13,000 miles · Jul 28, 2014
Visibility
TL* THE CONTACT OWNS A 2013 ACURA ILX. WHILE DRIVING APPROXIMATELY 65 MPH, THE CONTACT HEARD A LOUD POPPING SOUND INSIDE THE VEHICLE. THE CONTACT DISCOVERED THAT THE SUN ROOF GLASS WAS SHATTERED AND THE PANEL SIDING WAS IN THE UPRIGHT POSITION. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED. THE APPROXI…
Read full complaint
TL* THE CONTACT OWNS A 2013 ACURA ILX. WHILE DRIVING APPROXIMATELY 65 MPH, THE CONTACT HEARD A LOUD POPPING SOUND INSIDE THE VEHICLE. THE CONTACT DISCOVERED THAT THE SUN ROOF GLASS WAS SHATTERED AND THE PANEL SIDING WAS IN THE UPRIGHT POSITION. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE MANUFACTURER WAS NOTIFIED. THE APPROXIMATE FAILURE MILEAGE WAS 13,000.
NHTSA ODI #10616990
8,000 miles · Jun 29, 2014
Electrical System
OCTOBER 13, 2013 I WAS IN THE CHURCH PARKING LOT AND TRIED TO START THE CAR. THE CAR WON'T START OR CRANK UP.. JUNE 4, 2014, AGAIN THE ILX WON'T START OR CRANK UP. THE CAR WAS IN A PARKING LOT OF A SCHOOL. BOTH TIMES THE CAR HAD TO BE JUMP START. I WAS TOLD THE FOG LIGHT WAS USING UP THE BATTERY SO THE DEALER TURNED THE FOG LI…
Read full complaint
OCTOBER 13, 2013 I WAS IN THE CHURCH PARKING LOT AND TRIED TO START THE CAR. THE CAR WON'T START OR CRANK UP.. JUNE 4, 2014, AGAIN THE ILX WON'T START OR CRANK UP. THE CAR WAS IN A PARKING LOT OF A SCHOOL. BOTH TIMES THE CAR HAD TO BE JUMP START. I WAS TOLD THE FOG LIGHT WAS USING UP THE BATTERY SO THE DEALER TURNED THE FOG LIGHT OFF. THEN I WAS TOLD THE NAV WAS USING UP THE BATTERY AND FINALLY I WAS TOLD THE BATTERY CELL WAS FAULTY. THE ACURA DEALER FINALLY CHANGED THE BATTERY SINCE THE BATTERY IS STILL ON WARRANTY. I AM ON WAIT AND SEE SITUATION RIGHT NOW WHETHER I WOULD HAVE THE SAME BATTERY PROBLEM IN SIX MONTHS. *TR
NHTSA ODI #10606812
45 miles · Jun 10, 2014
EngineSuspension
SINCE ONE WEEK AFTER I PURCHASED THE ACURA ILX (CAR WAS NEW), I HAVE HEARD A RATTLING, BUMPING SOUND COMING FROM EITHER THE FRONT OR MIDDLE OF THE UNDERNEATH AREA OF THE CAR. I HAVE TAKEN IT TO THE ACURA DEALERSHIP WHERE I PURCHASED THE VEHICLE AND THEY TRIED 4 TIMES TO FIX IT, AND ALTHOUGH THE DEALERSHIP WAS VERY ACCOMMODATING…
Read full complaint
SINCE ONE WEEK AFTER I PURCHASED THE ACURA ILX (CAR WAS NEW), I HAVE HEARD A RATTLING, BUMPING SOUND COMING FROM EITHER THE FRONT OR MIDDLE OF THE UNDERNEATH AREA OF THE CAR. I HAVE TAKEN IT TO THE ACURA DEALERSHIP WHERE I PURCHASED THE VEHICLE AND THEY TRIED 4 TIMES TO FIX IT, AND ALTHOUGH THE DEALERSHIP WAS VERY ACCOMMODATING, THEY WERE UNABLE TO FIX THE VEHICLE AND THE SOUND REMAINED UNCHANGED. ONE OF THE TIMES THE VEHICLE WAS WITH THEM FOR OVER A MONTH. THE ANSWER I RECEIVED WAS THAT ACURA IS AWARE OF THE PROBLEM, THEY THINK IT IS THE ENGINE MOUNT, BUT NO FIX IS YET IN SIGHT. WHEN I DID AN INTERNET SEARCH OF "ACURA ILX NOISE" I DISCOVERED THAT THE ACURAZINE (ILX.ACURAZINE.COM) WEBSITE HAD MANY REVIEWS BY INDIVIDUALS WHO HAVE PURCHASED THE ILX NEW AND HAVE THE SAME PROBLEM. THE SOUND HAS BECOME PROGRESSIVELY WORSE IN THE YEAR I HAVE HAD IT AND I AM VERY CONCERNED OF THE SAFETY OF THIS CAR, ESPECIALLY WHEN DRIVING THE FREEWAY. I HAD INITIALLY THOUGHT ABOUT TURNING THE CAR OVER UNDER THE LEMON LAW (I LIVE IN NEVADA), BUT I WAS ASSURED BY ACURA THE PROBLEM WOULD BE FIXED. *TR
NHTSA ODI #10597516
1,825 miles · Oct 17, 2013
TiresWheelsCrash
WHILE DRIVING ON THE HIGHWAY, THE "CHECK TIRE PRESSURE" LIGHT CAME ON. I THEN PROCEEDED TO SLOW DOWN IN ORDER TO MAKE IT SAFELY TO THE NEXT GAS STATION OR REST STOP . ON ANY OTHER OCCASION, I WOULD HAVE PULLED OVER ON THE SIDE OF THE ROAD, BUT HIGHWAY SIGNS HAD INDICATED THAT NO STOPPING ON THE SIDE WAS ALLOWED. ALTHOUGH I W…
Read full complaint
WHILE DRIVING ON THE HIGHWAY, THE "CHECK TIRE PRESSURE" LIGHT CAME ON. I THEN PROCEEDED TO SLOW DOWN IN ORDER TO MAKE IT SAFELY TO THE NEXT GAS STATION OR REST STOP . ON ANY OTHER OCCASION, I WOULD HAVE PULLED OVER ON THE SIDE OF THE ROAD, BUT HIGHWAY SIGNS HAD INDICATED THAT NO STOPPING ON THE SIDE WAS ALLOWED. ALTHOUGH I WAS ATTEMPTING TO SAFELY REMAIN IN CONTROL OF THE VEHICLE, WITHIN 20 MINUTES MY CAR STARTED TO LOSE CONTROL AND FORCEFULLY SWERVED OFF THE HIGHWAY, CAUSING THE CAR TO RAPIDLY ROLL OFF OF THE SIDE OF THE HIGHWAY. IT SEEMED THAT THE TIRE HAD SEPARATED FROM THE RIM SPONTANEOUSLY, WITHOUT ANY INDICATION OF AN INCREASED WARNING FROM THE CAR'S INFORMATION / WARNING SYSTEM. *TR
NHTSA ODI #10548308
4,200 miles · Jun 13, 2013
Service BrakesCrash
PULLING UP TO A RED LIGHT AND WENT TO PRESS THE BRAKES AND THEY GAVE OUT AND HIT THE SUV IN FRONT OF ME. *TR
NHTSA ODI #10519617
300 miles · Apr 19, 2013
Structure
TL* THE CONTACT OWNS A 2013 ACURA ILX. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 45 MPH, HE NOTICED A LOUD, ABNORMAL ROAR FROM INSIDE THE CABIN OF THE VEHICLE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THERE WAS NOT A REPAIR AVAILABLE FOR THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE F…
Read full complaint
TL* THE CONTACT OWNS A 2013 ACURA ILX. THE CONTACT STATED THAT WHILE DRIVING APPROXIMATELY 45 MPH, HE NOTICED A LOUD, ABNORMAL ROAR FROM INSIDE THE CABIN OF THE VEHICLE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND STATED THAT THERE WAS NOT A REPAIR AVAILABLE FOR THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 300. *TR UPDATED 06/10/13 *BF
NHTSA ODI #10508850
Official recalls
6Dec 10, 2020
Honda (American Honda Motor Co.) is recalling certain 2013-2015 Acura ILX, 2013 Acura ILX Hybrid, 2012 Honda Civic Hybrid, and 2007-2008 Honda Fit vehicles with a manual transmission and 2009-2013 Honda Fit vehicles originally sold, or ever registered, in Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The drive shafts' protective coating may not have been applied properly during manufacturing, making it more susceptible to damage from road salt, or other contaminants, and potentially cause it to break.
Consequence & remedy
Consequence: A broken drive shaft may cause a sudden loss of drive power. The vehicle could also roll away if the parking brake has not been applied before the vehicle has been exited. Either condition can increase the risk of a crash or injury.
Remedy: Honda will notify owners, and dealers will inspect the drive shafts, replacing either the left or right drive shaft, if necessary, free of charge. Owners were notified of the safety risk with an interim letter mailed February 2, 2021. A second letter will be sent once the remedy is available. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are P9M, PAV, BAY, TAX, CA0, and MAZ.
Jun 27, 2019
Honda (American Honda Motor Co.) is recalling certain 2013 Acura ILX, 2015 RDX, 2005-2010 and 2012 RL, 2009-2014 TL, 2010 and 2012 ZDX, 2007-2011 CR-V, 2011-2013 and 2015 CR-Z, 2009-2013 Fit, 2013 Fit EV, 2010-2011 and 2013 Insight and 2007-2014 Ridgeline vehicles. These vehicles are equipped with driver frontal air bag inflators assembled as a recall remedy part or replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the driver frontal air bag inflator, free of charge. The recall began August 12, 2019. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are S5B and W59.
Mar 6, 2019
Honda (American Honda Motor Co.) is recalling specific 2003 Acura 3.2CL, 2013-2016 ILX, 2013-2014 ILX Hybrid, 2003-2006 MDX, 2007-2016 RDX, 2002-2003 3.2TL, 2004-2006, and 2009-2014 TL, 2010-2013 ZDX and 2001-2007 and 2009 Honda Accord, 2001-2005 Civic, 2003-2005 Civic Hybrid, 2001-2005 Civic GX NGV, 2002-2007 and 2010-2011 CR-V, 2003-2011 Element, 2007 Fit, 2002-2004 Odyssey, 2003-2008 Pilot, and 2006-2014 Ridgeline vehicles. The affected vehicles received a replacement driver air bag inflator as part of a previous Takata inflator recall remedy or a replacement driver air bag module containing the same inflator type as a service part. Due to a manufacturing error, in the event of a crash necessitating deployment of the driver frontal air bag, these inflators may explode.
Consequence & remedy
Consequence: An explosion of an inflator within the driver frontal air bag module may result in sharp metal fragments striking the driver, front seat passenger or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the driver's air bag inflator with an alternate inflator, free of charge. The recall began April 10, 2019. Honda owners may contact customer service at 1-888-234-2138. Honda's number for this recall is O41. Acura owners may contact customer service at 1-888-234-2138. Acura's number for this recall is U40.
Feb 3, 2016
Honda (American Honda Motor Co.) is recalling certain model year 2007-2011 Honda CR-V, 2011-2015 CR-Z, 2010-2014 FCX, and Insight, 2009-2013 Fit, 2013-2014 Fit EV, 2007-2014 Ridgeline, 2013-2016 Acura ILX, 2013-2014 Acura ILX Hybrid, 2007-2016 RDX, 2005-2012 Acura RL, 2009-2014 Acura TL, and 2010-2013 Acura ZDX vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the inflator, free of charge. The recall began March 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are JY0, JY1, and JY2.
Jun 13, 2014
American Honda Motor Co., Inc (Honda) is recalling certain model year 2013 Acura ILX vehicles manufactured January 16, 2012 to March 1, 2013, ILX Hybrid vehicles manufactured January 12, 2012 to February 7, 2013, and certain model year 2014 ILX vehicles manufactured May 2, 2013, to May 31, 2014, and ILX Hybrid vehicles manufactured October 18, 2013 to February 19, 2014. Excessive heat temperatures around the headlight bulb and reflector unit may diminish the output of the headlight and cause smoke, melting, and fire. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: The diminished light output may decrease the driver's visibility, increasing the risk of a crash. Additonally, the excessive heat coming from around the bulb and reflector could cause the headlights to overheat, increasing the risk of a fire.
Remedy: Honda will notify owners, and dealers will replace the headlights, free of charge. The recall began in July 2014. Owners may contact Acura customer service at 1-800-862-2872. Honda's number for this recall is JE9.
Jul 19, 2012
Honda is recalling certain model year 2012 Honda CR-V and model year 2013 Acura ILX vehicles. If the manual or power door lock is activated while an interior front door handle is being operated by an occupant, the cable connecting the interior door handle to the door latch mechanism may become loose and move out of position. There is a possibility that the cable can move far enough out of position to prevent the door from properly latching.
Consequence & remedy
Consequence: If the door is not fully latched, the door may open while driving or in a crash, increasing the risk of personal injury to the vehicle occupants.
Remedy: Honda will notify owners, and dealers will replace the front door latch assemblies in the affected vehicles, free of charge. Additionally, the interior front door handles in certain Honda CR-Vs will also be replaced, free of charge. The safety recall is expected to begin on, or about, August 16, 2012. Owners may contact Honda customer service at 1-800-999-1009.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration