NHTSA owner reports · September 18, 2026 snapshot.
Engine complaints
6 reportsClear category filterMileage unknown · Jul 14, 2026
EngineUnknown Or Other
I am submitting this complaint to document what I believe is a recurring defect involving the air conditioning compressor on my 2013 Acura ILX Hybrid. Vehicle history: * 2013: Vehicle purchased new. * 2019: Original A/C compressor failed and required replacement. * 2026: Replacement A/C compressor has failed again. This means…
Read full complaint
I am submitting this complaint to document what I believe is a recurring defect involving the air conditioning compressor on my 2013 Acura ILX Hybrid. Vehicle history: * 2013: Vehicle purchased new. * 2019: Original A/C compressor failed and required replacement. * 2026: Replacement A/C compressor has failed again. This means the vehicle is now on its third A/C compressor since new. Based on my experience, each compressor has lasted only about 4–6 years before failing. The first compressor replacement, performed by an Acura dealer in 2019, cost approximately $5,700. I have now been quoted approximately $3,600 by an independent repair facility and approximately $5,200 by an Acura dealer for the current repair. In addition to the extremely high repair cost, I have found that many independent A/C repair shops are reluctant to perform this repair because of the complexity and expense of replacing the compressor on this hybrid model. Replacement options are also very limited because this compressor is essentially an Acura OEM-specific component, with few, if any, widely available equivalent alternatives. The current failure began with a rattling/chattering noise whenever the A/C was engaged. Eventually, the compressor load became severe enough that the accessory belt was thrown off when the A/C engaged. An independent mechanic inspected the vehicle, ruled out the belt tensioner, and concluded that the compressor is the source of the problem. While compressors are wear items, replacing the compressor three times over the life of the vehicle—with each unit lasting only about five years—appears to be an unusually short service life, especially considering the exceptionally high cost of repair. In my opinion, this suggests a potential design or durability issue with the compressor used in the 2013 Acura ILX Hybrid. I am requesting that NHTSA document this complaint and review whether other owners of the same vehicle have experienced similar repeated compressor failur
NHTSA ODI #11750204
Mileage unknown · Feb 16, 2026
Electrical SystemEngineService Brakes
IIU malfunction not valid for this vin, even though it is the exact issue that every other model faced. Acura REFUSED to complete the repair without paying $3400
NHTSA ODI #11718193
Mileage unknown · Jun 1, 2024
Electrical SystemEngineSteering
Issue had not been persistent, on Sunday, May the 12th, 2024, while driving home, I was on a slight downward slope coming to a halt at a red light, when the car jolted slightly and the warning lights came. The auto-shutoff feature on the vehicle stopped working immediately. I was able to drive the car home, but after parking - t…
Read full complaint
Issue had not been persistent, on Sunday, May the 12th, 2024, while driving home, I was on a slight downward slope coming to a halt at a red light, when the car jolted slightly and the warning lights came. The auto-shutoff feature on the vehicle stopped working immediately. I was able to drive the car home, but after parking - the vehicle wouldn’t start again. Electronic screen on the radio came on and I could see error codes P1437 & P15A5. Also warnings on the dash to check IMA system, check charging system, check battery, check breaking system. Power steering locked up due to the voltage shortage. What is the reason/explanation provided by the dealer, as to what caused this issue? DTC'S P0A78 - MPI INTERNAL CIRCUIT MALFUNCTION, P1440 - MPI OUT CIRCUIT MALFUNCTION. MPI FAILING INTERNALLY, CAUSING 12V BATTERY TO LOSE CHARGE. Previously parts involved were recalled in Dec 2020, since American Honda didn’t not include my VIN they have refused to be of any assistance - monopolizing on being the only available source to change the parts. Had I received the recall, I would have had it addressed prior to the part going out. I’m 6330 miles over what they would have covered because I had no idea this was an issue until I found the safety bulletin which exactly described the recall and what happened to be my experience. Same issues, but I’m being told I couldn’t be included. They are charging me over $1400 for the part alone and then service which includes a complete removal of my back seats. I JUST spent nearly $4000 in Feb 2023 on the AC because the car wouldn’t start, who is to say this wasn’t undetected issue at the time?!
NHTSA ODI #11591884
Mileage unknown · Dec 28, 2023
Engine
engine failure
NHTSA ODI #11562398
Mileage unknown · Jul 25, 2023
Electrical SystemEngineVehicle Speed Control
On July 20th, 2023, while driving home from work, my vehicle without warning made a sudden jerk and all the warning light s came on the dash board. The car had reduced power and acceleration and an automated voice from the dash board warned to pull over the car. I pulled over into a garage who performed a diagnostic. They stated…
Read full complaint
On July 20th, 2023, while driving home from work, my vehicle without warning made a sudden jerk and all the warning light s came on the dash board. The car had reduced power and acceleration and an automated voice from the dash board warned to pull over the car. I pulled over into a garage who performed a diagnostic. They stated the error codes indicated MPI failure (IMA power moter invertor). They also stated there was a Service Bulletin 20-021 for tis issue with this car (same year /model). When a VIN check was performed, the vehicle did not come up on this TSB. I had the car towed to an acura dealer and they ran a diagnostic. They confirmed error codes P1440,P15A5,P0AE1,P0DA8 - all codes listed in the service builletin 20-021 for this vehicle year, make and model. I have no doubt, as the data indicates, this failure/incident was caused by the same issues which are covered under TSB 20-021 and this VIN should be included.
NHTSA ODI #11534323
45 miles · Jun 10, 2014
EngineSuspension
SINCE ONE WEEK AFTER I PURCHASED THE ACURA ILX (CAR WAS NEW), I HAVE HEARD A RATTLING, BUMPING SOUND COMING FROM EITHER THE FRONT OR MIDDLE OF THE UNDERNEATH AREA OF THE CAR. I HAVE TAKEN IT TO THE ACURA DEALERSHIP WHERE I PURCHASED THE VEHICLE AND THEY TRIED 4 TIMES TO FIX IT, AND ALTHOUGH THE DEALERSHIP WAS VERY ACCOMMODATING…
Read full complaint
SINCE ONE WEEK AFTER I PURCHASED THE ACURA ILX (CAR WAS NEW), I HAVE HEARD A RATTLING, BUMPING SOUND COMING FROM EITHER THE FRONT OR MIDDLE OF THE UNDERNEATH AREA OF THE CAR. I HAVE TAKEN IT TO THE ACURA DEALERSHIP WHERE I PURCHASED THE VEHICLE AND THEY TRIED 4 TIMES TO FIX IT, AND ALTHOUGH THE DEALERSHIP WAS VERY ACCOMMODATING, THEY WERE UNABLE TO FIX THE VEHICLE AND THE SOUND REMAINED UNCHANGED. ONE OF THE TIMES THE VEHICLE WAS WITH THEM FOR OVER A MONTH. THE ANSWER I RECEIVED WAS THAT ACURA IS AWARE OF THE PROBLEM, THEY THINK IT IS THE ENGINE MOUNT, BUT NO FIX IS YET IN SIGHT. WHEN I DID AN INTERNET SEARCH OF "ACURA ILX NOISE" I DISCOVERED THAT THE ACURAZINE (ILX.ACURAZINE.COM) WEBSITE HAD MANY REVIEWS BY INDIVIDUALS WHO HAVE PURCHASED THE ILX NEW AND HAVE THE SAME PROBLEM. THE SOUND HAS BECOME PROGRESSIVELY WORSE IN THE YEAR I HAVE HAD IT AND I AM VERY CONCERNED OF THE SAFETY OF THIS CAR, ESPECIALLY WHEN DRIVING THE FREEWAY. I HAD INITIALLY THOUGHT ABOUT TURNING THE CAR OVER UNDER THE LEMON LAW (I LIVE IN NEVADA), BUT I WAS ASSURED BY ACURA THE PROBLEM WOULD BE FIXED. *TR
NHTSA ODI #10597516
Official recalls
6Dec 10, 2020
Honda (American Honda Motor Co.) is recalling certain 2013-2015 Acura ILX, 2013 Acura ILX Hybrid, 2012 Honda Civic Hybrid, and 2007-2008 Honda Fit vehicles with a manual transmission and 2009-2013 Honda Fit vehicles originally sold, or ever registered, in Connecticut, Delaware, District of Columbia, Illinois, Indiana, Iowa, Kentucky, Maine, Maryland, Massachusetts, Michigan, Minnesota, Missouri, New Hampshire, New Jersey, New York, Ohio, Pennsylvania, Rhode Island, Vermont, Virginia, West Virginia, and Wisconsin. The drive shafts' protective coating may not have been applied properly during manufacturing, making it more susceptible to damage from road salt, or other contaminants, and potentially cause it to break.
Consequence & remedy
Consequence: A broken drive shaft may cause a sudden loss of drive power. The vehicle could also roll away if the parking brake has not been applied before the vehicle has been exited. Either condition can increase the risk of a crash or injury.
Remedy: Honda will notify owners, and dealers will inspect the drive shafts, replacing either the left or right drive shaft, if necessary, free of charge. Owners were notified of the safety risk with an interim letter mailed February 2, 2021. A second letter will be sent once the remedy is available. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are P9M, PAV, BAY, TAX, CA0, and MAZ.
Jun 27, 2019
Honda (American Honda Motor Co.) is recalling certain 2013 Acura ILX, 2015 RDX, 2005-2010 and 2012 RL, 2009-2014 TL, 2010 and 2012 ZDX, 2007-2011 CR-V, 2011-2013 and 2015 CR-Z, 2009-2013 Fit, 2013 Fit EV, 2010-2011 and 2013 Insight and 2007-2014 Ridgeline vehicles. These vehicles are equipped with driver frontal air bag inflators assembled as a recall remedy part or replacement service part, that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the driver frontal air bag inflator, free of charge. The recall began August 12, 2019. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are S5B and W59.
Mar 6, 2019
Honda (American Honda Motor Co.) is recalling specific 2003 Acura 3.2CL, 2013-2016 ILX, 2013-2014 ILX Hybrid, 2003-2006 MDX, 2007-2016 RDX, 2002-2003 3.2TL, 2004-2006, and 2009-2014 TL, 2010-2013 ZDX and 2001-2007 and 2009 Honda Accord, 2001-2005 Civic, 2003-2005 Civic Hybrid, 2001-2005 Civic GX NGV, 2002-2007 and 2010-2011 CR-V, 2003-2011 Element, 2007 Fit, 2002-2004 Odyssey, 2003-2008 Pilot, and 2006-2014 Ridgeline vehicles. The affected vehicles received a replacement driver air bag inflator as part of a previous Takata inflator recall remedy or a replacement driver air bag module containing the same inflator type as a service part. Due to a manufacturing error, in the event of a crash necessitating deployment of the driver frontal air bag, these inflators may explode.
Consequence & remedy
Consequence: An explosion of an inflator within the driver frontal air bag module may result in sharp metal fragments striking the driver, front seat passenger or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the driver's air bag inflator with an alternate inflator, free of charge. The recall began April 10, 2019. Honda owners may contact customer service at 1-888-234-2138. Honda's number for this recall is O41. Acura owners may contact customer service at 1-888-234-2138. Acura's number for this recall is U40.
Feb 3, 2016
Honda (American Honda Motor Co.) is recalling certain model year 2007-2011 Honda CR-V, 2011-2015 CR-Z, 2010-2014 FCX, and Insight, 2009-2013 Fit, 2013-2014 Fit EV, 2007-2014 Ridgeline, 2013-2016 Acura ILX, 2013-2014 Acura ILX Hybrid, 2007-2016 RDX, 2005-2012 Acura RL, 2009-2014 Acura TL, and 2010-2013 Acura ZDX vehicles. The affected vehicles are equipped with a dual-stage driver frontal air bag that may be susceptible to moisture intrusion which, over time, could cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Honda will notify owners, and dealers will replace the inflator, free of charge. The recall began March 2017. Owners may contact Honda customer service at 1-888-234-2138. Honda's numbers for this recall are JY0, JY1, and JY2.
Jun 13, 2014
American Honda Motor Co., Inc (Honda) is recalling certain model year 2013 Acura ILX vehicles manufactured January 16, 2012 to March 1, 2013, ILX Hybrid vehicles manufactured January 12, 2012 to February 7, 2013, and certain model year 2014 ILX vehicles manufactured May 2, 2013, to May 31, 2014, and ILX Hybrid vehicles manufactured October 18, 2013 to February 19, 2014. Excessive heat temperatures around the headlight bulb and reflector unit may diminish the output of the headlight and cause smoke, melting, and fire. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard No. 108, "Lamps, Reflective Devices, and Associated Equipment."
Consequence & remedy
Consequence: The diminished light output may decrease the driver's visibility, increasing the risk of a crash. Additonally, the excessive heat coming from around the bulb and reflector could cause the headlights to overheat, increasing the risk of a fire.
Remedy: Honda will notify owners, and dealers will replace the headlights, free of charge. The recall began in July 2014. Owners may contact Acura customer service at 1-800-862-2872. Honda's number for this recall is JE9.
Jul 19, 2012
Honda is recalling certain model year 2012 Honda CR-V and model year 2013 Acura ILX vehicles. If the manual or power door lock is activated while an interior front door handle is being operated by an occupant, the cable connecting the interior door handle to the door latch mechanism may become loose and move out of position. There is a possibility that the cable can move far enough out of position to prevent the door from properly latching.
Consequence & remedy
Consequence: If the door is not fully latched, the door may open while driving or in a crash, increasing the risk of personal injury to the vehicle occupants.
Remedy: Honda will notify owners, and dealers will replace the front door latch assemblies in the affected vehicles, free of charge. Additionally, the interior front door handles in certain Honda CR-Vs will also be replaced, free of charge. The safety recall is expected to begin on, or about, August 16, 2012. Owners may contact Honda customer service at 1-800-999-1009.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration