← New search

2013 Toyota Sienna

Owner reports · Recalls · Investigations

Similar to other model years

Owner complaints for the 2013 Toyota Sienna do not stand out strongly from the model-year median of 183.

About this comparison →

When problems were reported

Mileage at the reported incident

100 reports with mileage · 83 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Structure. Review the 44 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Air Bags. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electrical System. Review the 22 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

7 crash reports1 fire reports8 injury reports

Structure complaints

44 reports
Clear category filter
48,000 miles · Dec 19, 2017
Structure

I HAVE HAD A SLIDING DOOR FAILURE, EXACTLY AS DESCRIBED IN NOTIFICATION ZH4 AND ZH5, AND SAFETY RECALL 16V-858. THE REAR SLIDING DOOR WOULD NOT FULLY CLOSE, OR WOULD NOT LATCH, AND WOULD OFTEN RE-OPEN AUTOMATICALLY. THE DOOR EXHIBITED A GRINDING NOISE AND WOULD OFTEN NOT LATCH. THIS ON A VEHICLE JUST OVER 3 YEARS OLD WITH 4…

Read full complaint

I HAVE HAD A SLIDING DOOR FAILURE, EXACTLY AS DESCRIBED IN NOTIFICATION ZH4 AND ZH5, AND SAFETY RECALL 16V-858. THE REAR SLIDING DOOR WOULD NOT FULLY CLOSE, OR WOULD NOT LATCH, AND WOULD OFTEN RE-OPEN AUTOMATICALLY. THE DOOR EXHIBITED A GRINDING NOISE AND WOULD OFTEN NOT LATCH. THIS ON A VEHICLE JUST OVER 3 YEARS OLD WITH 48,880 MILES ON IT, ALWAYS GARAGED AND NEVER IN AN ACCIDENT. WHEN I THE VEHICLE IN TO THE DEALER ON JUNE 13TH, 2017, THE DEALER REPAIRED THE PROBLEM BY REPLACING THE UPPER DOOR HINGE WHICH APPARENTLY HAD FAILED. I WAS CHARGED $323.46 AND WAS TOLD IT WAS NOT COVERED UNDER MY WARRANTY. AFTER THE RECALL WAS ANNOUNCED, I CONTACTED TOYOTA AND REQUESTED REIMBURSEMENT, WHICH WAS DENIED AS THEY SAID THE CONDITION MY VEHICLE EXHIBITED WAS NOT COVERED BY THE RECALL. I DON'T UNDERSTAND WHY THIS SERIOUS SAFETY DEFECT ON A CURRENT VEHICLE IS NOT COVERED BY TOYOTA WHEN THE SYMPTOM MIRRORS THAT DESCRIBED IN THE CURRENT RECALL.

NHTSA ODI #11055496

74,000 miles · Nov 10, 2017
Structure

I HAD THE RECENT SLIDING DOOR RECALL DONE BUT MY DRIVER'S SIDE SLIDING DOOR STILL ISN'T WORKING CORRECTLY. AFTER THE FIX THE CAR WAS HARD TO START SOMETIMES, AS IF THE BATTERY WAS GETTING WEAK. I PUT AN AMMETER ON THE POSITIVE LEAD OF THE BATTERY AND NOTICES MINIMAL AMPERAGE UNTIL I STARTED OPERATING THE DRIVER SIDE SLIDING …

Read full complaint

I HAD THE RECENT SLIDING DOOR RECALL DONE BUT MY DRIVER'S SIDE SLIDING DOOR STILL ISN'T WORKING CORRECTLY. AFTER THE FIX THE CAR WAS HARD TO START SOMETIMES, AS IF THE BATTERY WAS GETTING WEAK. I PUT AN AMMETER ON THE POSITIVE LEAD OF THE BATTERY AND NOTICES MINIMAL AMPERAGE UNTIL I STARTED OPERATING THE DRIVER SIDE SLIDING DOOR, THEN THERE WAS A 2.4 AMP DRAW EVEN AFTER THE DOORS WERE CLOSED AND THE CAR WAS LOCKED. THE DOOR ALSO SOMETIMES WILL OPEN WITH A POPPING NOISE AS IF THE DOOR ISN'T LATCHING PROPERLY SOMETIMES. WHILE TESTING, THE DRIVER SIDE SLIDING DOOR GOT TO WHERE IT WOULD NOT OPEN OR CLOSE USING THE OVERHEAD BUTTON, THE DOOR POST BUTTON, OR THE REMOTE DOOR BUTTON. WHILE TRYING TO CLOSE THE DOOR MANUALLY IT WOULD ROLL FOR A SHORT DISTANCE AND STOP. AFTER SITTING A FEW SECONDS I CAN CLOSE IT A LITTLE MORE BUT THEN THE SAME THING WOULD HAPPEN. IT TOOK SEVERAL ATTEMPTS TO GET THE DOOR TO CLOSE. THE PASSENGER SIDE DOOR OPENS AND CLOSES NORMALLY. NO POPPING NOISE AND THE BUTTONS WORK EVEN WHEN THE BUTTONS FOR THE DRIVER SIDE SLIDING DOOR DO NOT.

NHTSA ODI #11045135

Mileage unknown · Nov 6, 2017
Structure

2013 TOYOTA SIENNA. CONSUMER WRITES IN REGARDS TO SAFETY RECALL NOT BEING REPAIRED IN A TIMELY MANNER. *LD THE CONSUMER STATED THE BACK PASSENGER DOOR WOULD NOT OPEN. IT WAS REPAIRED BUT THE FAILURE RECURRED. UPDATED 11/6/2017*JS

NHTSA ODI #11041248

26,000 miles · Oct 19, 2017
Structure

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. WHILE DRIVING APPROXIMATELY 45 MPH, THE DRIVER'S SIDE SLIDING DOOR OPENED. THE CONTACT STOPPED THE VEHICLE AND SWITCHED THE DOOR TO MANUAL OPERATION. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V858000 (STRUCTURE). THE CONTACT TOOK THE VEHICLE TO THE DEALER (GREENFIELD…

Read full complaint

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. WHILE DRIVING APPROXIMATELY 45 MPH, THE DRIVER'S SIDE SLIDING DOOR OPENED. THE CONTACT STOPPED THE VEHICLE AND SWITCHED THE DOOR TO MANUAL OPERATION. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V858000 (STRUCTURE). THE CONTACT TOOK THE VEHICLE TO THE DEALER (GREENFIELD TOYOTA, GREENFIELD, MA, 413-772-0231), BUT THE FAILURE WAS NOT REMEDIED DUE TO A HANDICAP SEAT THAT WAS INSTALLED ON THE FRONT PASSENGER SIDE. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND WANTED THE HANDICAP SEAT REMOVED BEFORE THE RECALL REMEDY COULD BE PERFORMED. THE FAILURE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 26,000.

NHTSA ODI #11034592

26,000 miles · Oct 19, 2017
Structure

WHILE DRIVING HOME FROM THE TOYOTA DEALERSHIP FOLLOWING ROUTINE MAINTENANCE MY DRIVERS SIDE SLIDING DOOR OPENED WHILE TRAVELING AT SPEED. I WENT ONLINE AND LEARNED THERE IS A SAFETY RECALL ISSUED FOR MY VEHICLE FOR THIS PROBLEM. I CALLED THE DEALERSHIP AND SCHEDULED A VISIT TO HAVE THE PROBLEM FIXED. WHEN I ARRIVED THEY REFUSED …

Read full complaint

WHILE DRIVING HOME FROM THE TOYOTA DEALERSHIP FOLLOWING ROUTINE MAINTENANCE MY DRIVERS SIDE SLIDING DOOR OPENED WHILE TRAVELING AT SPEED. I WENT ONLINE AND LEARNED THERE IS A SAFETY RECALL ISSUED FOR MY VEHICLE FOR THIS PROBLEM. I CALLED THE DEALERSHIP AND SCHEDULED A VISIT TO HAVE THE PROBLEM FIXED. WHEN I ARRIVED THEY REFUSED TO MAKE THE REPAIR BECAUSE I HAD A BRUNO HANDICAPPED SEAT INSTALLED SO THAT MY WIFE, WHO IS HANDICAPPED, COULD ENTER AND EXIT THE VEHICLE. THEY SAID I WOULD HAVE TO HAVE THE SEAT REMOVED BEFORE THEY COULD MAKE THE REPAIR. I CONTACTED THE COM[PANY THAT INSTALLED THE SEAT WHO SAID IT WOULD COST A MINIMUM OF $500 TO REMOVE AND REINSTALL THE SEAT. IT IS TOYOTA'S DOOR THAT IS DEFECTIVE AND I FEEL THEY SHOULD BE RESPONSIBLE FOR ANY COSTS FOR REPAIR. THEIR RECALL NOTICE ALSO STATES REPAIRS WILL BE MADE AT "NO CHARGE" TO THE CUSTOMER.

NHTSA ODI #11034588

Mileage unknown · Sep 21, 2017
Structure

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V858000 (STRUCTURE); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CALLED TEAM TOYOTA AT (219) 898-4466 …

Read full complaint

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V858000 (STRUCTURE); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CALLED TEAM TOYOTA AT (219) 898-4466 (LOCATED AT 400 INDIANAPOLIS BLVD, SCHERERVILLE, IN 46375) WHERE AN APPOINTMENT WAS SCHEDULED FOR AUGUST 17, 2017. WHEN THE VEHICLE WAS TAKEN TO THE DEALER ON THAT DATE, THE CONTACT WAS INFORMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS NOTIFIED OF THE ISSUE AND STATED THAT PARTS WERE AVAILABLE. THE CONTACT WAS ADVISED TO TAKE THE VEHICLE TO ANY TOYOTA DEALER. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.

NHTSA ODI #11024857

50,000 miles · Sep 18, 2017
Structure

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. WHILE THE VEHICLE WAS STATIONARY, BOTH SLIDING DOORS MALFUNCTIONED. THE CONTACT STATED THAT THE DOORS REMAINED OPEN WHEN PROMPTED TO AUTOMATICALLY CLOSE. IN ADDITION, THE SLIDING DOORS HAD TO BE MANUALLY LOCKED AND UNLOCKED. A DEALER AND THE MANUFACTURER WERE NOT AWARE OF THE FAILURE. T…

Read full complaint

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. WHILE THE VEHICLE WAS STATIONARY, BOTH SLIDING DOORS MALFUNCTIONED. THE CONTACT STATED THAT THE DOORS REMAINED OPEN WHEN PROMPTED TO AUTOMATICALLY CLOSE. IN ADDITION, THE SLIDING DOORS HAD TO BE MANUALLY LOCKED AND UNLOCKED. A DEALER AND THE MANUFACTURER WERE NOT AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 50,000.

NHTSA ODI #11023955

Mileage unknown · Aug 21, 2017
Structure

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V858000 (STRUCTURE); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE LOCAL DEALER WAS NOT CONTACTED. THE MANUFACTU…

Read full complaint

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V858000 (STRUCTURE); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE LOCAL DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS NOT NOTIFIED. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.

NHTSA ODI #11018664

Mileage unknown · Aug 21, 2017
Structure

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V858000 (STRUCTURE); HOWEVER, THE PART NEEDED FOR THE REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CALLED VANDERGRIFF TOYOTA (LOCAT…

Read full complaint

TL* THE CONTACT OWNS A 2013 TOYOTA SIENNA. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V858000 (STRUCTURE); HOWEVER, THE PART NEEDED FOR THE REPAIR WAS NOT AVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE CONTACT CALLED VANDERGRIFF TOYOTA (LOCATED AT 1000 W INTERSTATE 20, ARLINGTON, TX 76017). THE DEALER IS CURRENTLY PREPARING THE REMEDY PART AND STATED THAT THEY WOULD NOTIFY THE CONTACT WHEN PARTS BECOME AVAILABLE. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.

NHTSA ODI #11016506

Mileage unknown · Aug 7, 2017
Structure

TOYOTA HAS YET TO FIX THE POWER SLIDING DOOR PROBLRSM FOR MY VEHICLE. I AM HANDICAPPED AND THE POWER DOORS WERE THE REASON I BOUGHT THIS VEHICLE. I HAVE TRIED THREE TIMES TO GET THIS FIXED. THE LATEST TIME THEY SET UP THE APPOINTMENT AND THEN CALLED STATING THAT THEY COULDN'T FIX IT AND AGAIN I NEEDED TO WAIT. I JUST NEED THIS F…

Read full complaint

TOYOTA HAS YET TO FIX THE POWER SLIDING DOOR PROBLRSM FOR MY VEHICLE. I AM HANDICAPPED AND THE POWER DOORS WERE THE REASON I BOUGHT THIS VEHICLE. I HAVE TRIED THREE TIMES TO GET THIS FIXED. THE LATEST TIME THEY SET UP THE APPOINTMENT AND THEN CALLED STATING THAT THEY COULDN'T FIX IT AND AGAIN I NEEDED TO WAIT. I JUST NEED THIS FIXED AS SOON AS POSSIBLE. THIS RECALL HAS BEEN OUT FOR A VERY LONG TIME BUT THEY HAVE YET TO TRY TO FIX MY VAN.

NHTSA ODI #11013515

Official recalls

6

19V741000 · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

Oct 17, 2019

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

Additional source detail variants (2)

Air Bags:frontal:passenger Side:inflator Module

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

Air Bags:frontal:driver Side:inflator Module

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.

19V553000 · Service Brakes, Hydraulic:foundation Components:hoses, Lines/piping, And Fittings

Jul 25, 2019

Vantage Mobility International, LLC (Vantage) is recalling certain 2012-2018 AMS Genesis wheelchair vans, built on a Toyota Sienna vehicles. The rubber brake hoses that attach to the rear wheel assembly may be too short, causing them to rub against the rear axle trailing arm.

Consequence & remedy

Consequence: The contact may cause failure of the rear brake hoses, resulting in a loss of vehicle control and reduced braking ability, increasing the risk of a crash.

Remedy: Vantage will notify owners, and dealers will install a set of rear brake hoses that will provide the proper clearance, free of charge. The recall began December 16, 2019. Owners may contact Vantage customer service at 1-800-488-9082.

19V005000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2019

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2014-2016 Toyota 4Runner, 2014-2015 Scion xB, Lexus IS350C, IS250C, 2014 Toyota Sienna, Lexus IS-F, and 2014-2017 Lexus GX460 vehicles sold, or ever registered in the states of Alabama, California, Florida, Georgia, Hawaii, Louisiana, Mississippi, South Carolina, Texas, Puerto Rico, American Samoa, Guam, the Northern Mariana Islands (Saipan), and the U.S. Virgin Islands or "Zone A." Toyota is also recalling certain 2011-2013 Toyota Corolla, Corolla Matrix, Lexus IS250, IS350, 2011-2016 4Runner, 2011-2015 Scion xB, Lexus IS350C, IS250C, 2011-2014 Toyota Sienna, Lexus IS-F, 2011-2017 Lexus GX460, and 2011-2012 Lexus ES350 vehicles ever registered in the states of Arizona, Arkansas, Delaware, District of Columbia, Illinois, Indiana, Kansas, Kentucky, Maryland, Missouri, Nebraska, Nevada, New Jersey, New Mexico, North Carolina, Ohio, Oklahoma, Pennsylvania, Tennessee, Virginia, and West Virginia or "Zone B." Toyota is also recalling certain 2010-2013 Toyota Corolla, Corolla Matrix, Lexus IS350, 2010-2016 4Runner, 2010-2013 Lexus IS250, 2010-2015 Scion xB, Lexus IS350C, IS250C, 2010-2017 Lexus GX460, 2010-2014 Lexus IS-F, and 2010-2012 Lexus ES350 vehicles ever registered in the states of Alaska, Colorado, Connecticut, Idaho, Iowa, Maine, Massachusetts, Michigan, Minnesota, Montana, New Hampshire, New York, North Dakota, Oregon, Rhode Island, South Dakota, Utah, Vermont, Washington, Wisconsin, and Wyoming or "Zone C." These vehicles are equipped with air bag inflators assembled as part of the passenger frontal air bag modules, used as original equipment or replacement equipment (such as after a vehicle crash necessitating replacement of the original air bags), that may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front passenger air bag inflator, or replace the air bag assembly. The recall began February 15, 2019. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are "Zone A" Toyota: G0P, Lexus: GLG; "Zone B" Toyota: G0R, Lexus GLH; "Zone C" Toyota: H0A, and Lexus: HLA.

18V024000 · Air Bags:frontal:passenger Side:inflator Module

Jan 9, 2018

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2013 Scion xB, Toyota Corolla, Corolla Matrix, Sienna, 4Runner, Lexus IS250, IS350, IS250C, IS350C, IS-F, and GX460 vehicles sold, ever registered, in the states of AL, CA, FL, GA, HI, LA, MS, SC, TX, PR, AS, GU, the MP (Saipan), and the U.S. VI or "Zone A." Toyota is also recalling certain 2010 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, 4Runner, Lexus IS250, IS350, IS250C, IS350C, ES350, IS-F, GX460, and Pontiac Vibe vehicles sold, ever registered, in the states of AZ, AR, DE, DC, IL, IN, KS, KY, MD, MO, NE, NV, NJ, NM, NC, OH, OK, PA, TN, VA, and WV or "Zone B." Toyota is also recalling certain 2009 Scion xB, Toyota Corolla, Corolla Matrix, Yaris, Lexus IS250, IS350, ES350, IS-F, and Pontiac Vibe vehicles ever registered in the states of AK, CO, CT, ID, IA, ME, MA, MI, MN, MT, NH, NY, ND, OR, RI, SD, UT, VT, WA, WI, and WY or "Zone C." These vehicles are equipped with certain air bag inflators assembled as part of the passenger frontal air bag modules used as original equipment or replacement equipment. In the event of a crash necessitating deployment of the passenger frontal air bag, these inflators may explode due to propellant degradation occurring after long-term exposure to absolute humidity and temperature cycling.

Consequence & remedy

Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.

Remedy: Toyota will notify the Toyota, Scion and Lexus owners. General Motors will contact the Pontiac owners. Depending on the vehicle model, dealers will replace the front passenger air bag inflator, or replace the air bag assembly. The recall began on January 29, 2018. Owners may contact Toyota customer service at 1-800-331-4331, or Pontiac customer service at 1-800-762-2737. Toyota's numbers for this recall are "Zone A" Toyota: G0P, Lexus: GLG; "Zone B" Toyota: G0R, Lexus GLH; "Zone C" Toyota: H0A, and Lexus: HLA.

16V858000 · Structure:body:door

Nov 29, 2016

Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2011-2016 Toyota Sienna minivans manufactured January 4, 2010, to August 12, 2016. If the power sliding door is unable to be opened when commanded, such as if the door is frozen shut, the door may subsequently open unexpectedly, possibly while the vehicle is moving.

Consequence & remedy

Consequence: If door opens while the vehicle is moving, there would be an increased risk of injury to the vehicle occupants.

Remedy: Toyota will notify owners, and dealers will replace the junction block, rear sliding door wire harnesses, and install two sub wire harnesses, free of charge. The recall began on July 28, 2017. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G04.

13V014000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seats

Jan 16, 2013

Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.

Consequence & remedy

Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.

Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.

Additional source detail variants (2)

Seats

Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.

Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.

Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.

Air Bags:frontal:sensor/control MODULE-INACTIVE

Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.

Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.

Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

1

EA21002 · Desiccated Air Bag Inflator Rupture

Opened Sep 17, 2021 · No close date supplied

Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Additional source detail variants (2)

Air Bags:frontal:driver Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.

Air Bags:frontal:passenger Side:inflator Module

From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.