IllustrationVEHICLE SPEED CONTROL: THE RAV4 HAS SOME SPEED CONTROL PROBLEMS. SOMETIMES, IT DOES NOT DOWN-SHIFT PROPERLY. THEN, SUDDENLY IT DOWN SHIFTS AND ACCELERATES EXTREMELY. THERE IS NO CERTAIN WAY OF CONTROLLING THE SHIFT. IT MAY CREATE HAZARDOUS SITUATIONS ESPECIALLY MERGING TO THE TRAFFIC. *NM
2006 Toyota RAV4
Owner reports · Recalls · Investigations
More warning signs than most RAV4 years
Owner complaints for the 2006 Toyota RAV4 are substantially higher than the model-year median of 258.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all RAV4 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
1130–25K
12025–50K
12450–75K
8075–100K
81100–150K
22150K+
540 reports with mileage · 164 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 230 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 109 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 74 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
26 crash reports5 fire reports9 injury reports
What owners actually said
704 reportsANOTHER DRIVER WAS DOING ABOUT 60 WEDNESDAY NIGHT IN THE POURING RAIN AND HIT A LOW SPOT ON THE FREEWAY THAT HAD ABOUT 3" OF WATER IN IT. HE DIDN'T SEE IT SOON ENOUGH TO AVOID IT SO HE JUST HUNG ON TO THE STEERING WHEEL AND PRAYED. THE CAR SLOWED DOWN QUITE A BIT BUT KEPT GOING STRAIGHT SPRAYING WATER EVERYWHERE. THE NOISE FROM …
Read full complaint
ANOTHER DRIVER WAS DOING ABOUT 60 WEDNESDAY NIGHT IN THE POURING RAIN AND HIT A LOW SPOT ON THE FREEWAY THAT HAD ABOUT 3" OF WATER IN IT. HE DIDN'T SEE IT SOON ENOUGH TO AVOID IT SO HE JUST HUNG ON TO THE STEERING WHEEL AND PRAYED. THE CAR SLOWED DOWN QUITE A BIT BUT KEPT GOING STRAIGHT SPRAYING WATER EVERYWHERE. THE NOISE FROM THE WATER HITTING THE UNDERSIDE OF THE CAR WAS DEAFENING. THE NEXT DAY THE CHECK ENGINE LIGHT, VSC LIGHT AND 4X4 LIGHT, CAME ON. HE STOPPED BY THE DEALER ON HIS WAY HOME TO HAVE IT CHECKED. HE WAS IN THE WAITING ROOM A FEW MINUTES WHEN THE SERVICE MGR. CAME AND GOT HIM SAYING HE WANTED TO SHOW HIM SOMETHING. THEY WENT OUT SIDE AND HE POINTED TO THE VEHICLE. THERE WERE TWO HOSES HANGING FROM THE CAR BELOW THE DRIVERS SEAT. IT SEEMS THERE WAS A PLASTIC CANISTER BEHIND THE CHARCOAL FILTER THAT RECIRCS TANK FUMES BACK TO THE ENGINE. IT GOT RIPPED OFF WHEN HE HIT THAT PUDDLE. HE EXPLAINED TO HIM WHAT HAD HAPPENED AND HE TOLD HIM THAT WARRANTY WOULDN'T COVER THE DAMAGE (~$150.00). HE TOLD HIM THAT HE HAD NEVER LOST CAR PARTS BY DRIVING THROUGH A PUDDLE IN ALL HIS YEARS OF DRIVING. HE WAS UNSYMPATHETIC TO SAY THE LEAST. THE WORST PART ABOUT THIS IS THE PARTS ARE ON BACKORDER FROM TOYOTA AND THEY DON'T KNOW WHEN THEY'LL HAVE THEM. UNTIL THEN, THE LIGHTS WERE ON ON THE DASH. *NM
WHEN USING THE DRYER IN A CAR WASH THE HARD SPARE TIRE COVER WAS BLOWN OFF THE SPARE TIRE AND BASHED AGAINST THE VEHICLE AND THEN THE GROUND SEVERELY SCRATCHING IT AND CRACKING IT. HAD IT NO COMPLETELY COME OFF AT THAT POINT IT IS PROBABLE THAT IT WOULD HAVE FLOWN OFF INTO THE FROM OF ANY FOLLOWING VEHICLE HAD I BEEN TRAVELING …
Read full complaint
WHEN USING THE DRYER IN A CAR WASH THE HARD SPARE TIRE COVER WAS BLOWN OFF THE SPARE TIRE AND BASHED AGAINST THE VEHICLE AND THEN THE GROUND SEVERELY SCRATCHING IT AND CRACKING IT. HAD IT NO COMPLETELY COME OFF AT THAT POINT IT IS PROBABLE THAT IT WOULD HAVE FLOWN OFF INTO THE FROM OF ANY FOLLOWING VEHICLE HAD I BEEN TRAVELING DOWN A BUSY ROAD POTENTIALLY CAUSING AN ACCIDENT. THESE ITEMS SHOULD "NEVER" COME OF UNDER NORMAL USE CONDITIONS. THIS IS A SERIOUS POTENTIAL ACCIDENT SOURCE AS WELL AS A POTENTIAL SOURCE OF A LAW SUIT AGAINST THE OWNER OPERATOR OF THE VEHICLE. IN ADDITION IT IS HARD AND CAN CAUSE WINDSHIELD DAMAGE TO ANY FOLLOWING VEHICLES AND SHOULD NEVER COME OFF WHEN PROPERLY ATTACHED. *NM
HESITATION PROBLEM - '06 RAV4 I4 SPORT MODEL WHEN TRYING TO OVERTAKE, WHEN PRESSING THE PEDAL HARDER, ENGINE DIDN'T RESPOND RIGHT AWAY. *JB
2006 TOYOTA RAV4, SPORT, 4X4. SOMETIMES WHILE PUSHING DOWN THE GAS PEDAL, THE CAR WILL HESITATE FOR ABOUT 1 OR 2 SECONDS BEFORE SPEEDING FORWARD. THIS IS USUALLY WHEN AT A VERY SLOW SPEED, LESS THAN 15 MILES/HR. IT HAS BEEN MOST NOTICEABLE MAKING LEFT AND RIGHT HAND TURNS NOT FROM A FULL STOP. THE FORWARD ACCELERATION AFTER …
Read full complaint
2006 TOYOTA RAV4, SPORT, 4X4. SOMETIMES WHILE PUSHING DOWN THE GAS PEDAL, THE CAR WILL HESITATE FOR ABOUT 1 OR 2 SECONDS BEFORE SPEEDING FORWARD. THIS IS USUALLY WHEN AT A VERY SLOW SPEED, LESS THAN 15 MILES/HR. IT HAS BEEN MOST NOTICEABLE MAKING LEFT AND RIGHT HAND TURNS NOT FROM A FULL STOP. THE FORWARD ACCELERATION AFTER THE HESITATION IS VERY EXTREME, EVEN WHEN I AM NOT PRESSING THE GAS PEDAL HEAVILY. THIS DOES NOT OCCUR ALL THE TIME AND I HAVE NOT NOTICED A TREND OF WHEN IT DOES OR DOES NOT HAPPEN (E.G., WEATHER, TEMPERATURE OF CAR OR AIR). *NM
SAT, JULY 1, 2006 THE REAR WINDOW OF MY 2006 TOYOTA RAV4 SIMPLY BLEWOUT SITTING IN OUR DRIVEWAY. THERE WAS NO TRAFFIC, PRECIPITATION OR WIND AND TEMP HOVERED 75-80 DEGREES. MOST OF GLASS REMAINED LOOSELY INTACT BUT WAS ALL SHATTERED WITH A MEDIUM SIZE HOLE IN THE RIGHT SIDE OF THE REAR WINDOW, WITH SMALL FRAGMENTS FOUND OUTSIDE…
Read full complaint
SAT, JULY 1, 2006 THE REAR WINDOW OF MY 2006 TOYOTA RAV4 SIMPLY BLEWOUT SITTING IN OUR DRIVEWAY. THERE WAS NO TRAFFIC, PRECIPITATION OR WIND AND TEMP HOVERED 75-80 DEGREES. MOST OF GLASS REMAINED LOOSELY INTACT BUT WAS ALL SHATTERED WITH A MEDIUM SIZE HOLE IN THE RIGHT SIDE OF THE REAR WINDOW, WITH SMALL FRAGMENTS FOUND OUTSIDE OF WINDOW. SMALL PIECES OF GLASS CONTINUED TO FALL OUT. THE CAR HAD BEEN SITTING COLD (NOT RUNNING) SINCE THE EVENING PRIOR (6:30PM) AND WAS IN PARTLY SHADED AREA. BOTH REAR DRIVER/ PASSENGER SIDE WINDOWS LOWERED ABOUT 2 INCHES TO CIRCULATE AIR. NOTHING WAS IN CAR TO CONTRIBUTE TO INTERNAL PRESSURE AND NOTHING HIT THE CAR AS I WAS WITNESS TO THIS EVENT AS IT OCCURRED. DRIVEWAY IS ON A HILL; CAR FACED FORWARD AND ANGLED DOWN THE HILL TOWARD GARAGE (CAR REAR END HIGHEST). LARGE GLASS PIECES FOUND MOSTLY OUTSIDE OF CAR JUST BELOW WINDOW WITH SOME LARGER PIECES LAYING ON OUTSIDE OF REAR DOOR WITH SMALLER FRAGMENTS ON THE GROUND BELOW. SMALL GLASS FRAGMENTS FOUND INSIDE CAR BELOW WINDOW. PICTURES TAKEN. TOYOTA CONTACTED AND QUESTIONED AS TO NEXT STEP. TOYOTA REPRESENTATIVE OFFERED NOTHING AS THIS WAS HOLIDAY WEEKEND AND NOTHING WAS AVAILABLE,ACCORDING TO TOYOTA. AUTO GLASS REPAIR COMPANIES CALLED AND NO ONE AVAILABLE DUE TO HOLIDAY. INSURANCE COMPANY CALLED, GIVEN SAME STORY AGAIN! TOYOTA CALLED AGAIN. CAN'T LEAVE CAR SIT WITH BROKEN REAR WINDOW AND WE EXPECT RAIN. ASKED ABOUT KNOCKING REST OF GLASS OUT AS THE GLASS NEEDED TO BE CLEANED UP AND OPENING NEEDED TO BE SECURED. I EXPLAINED I COULDN'T DRIVE THE CAR, IT WAS UNSAFE TO DRIVE & TOWING WAS NOT AN OPTION AS NEAREST TOYOTA DEALER DIDN'T HAVE TOWING CAPACITY...AND CLOSED IN AN HOUR. KNOCKED REST OF GLASS OUT AND TAPED UP REAR WINDOW OPENING. DROVE TO DEALER MON MORNING TO LEAVE RAV FOR REPAIR AND SECURED RENTAL CAR. TOLD MY CAR WOULD NOT BE LOOKED AT UNTIL WED. THUR MY CAR LOOKED AT AND NEW WINDOW ORDERED AND HOPED TO BE HERE IN A WEEK OR SO. BROKEN GLASS DISPOSED OF. *NM
A 2006 TOYOTA RAV4 V6 LIMITED 4X2. PROBLEM: AUTOMATIC TRANSMISSION DEFECT? SOMETIMES WHEN I STEP ON ACCELERATOR THERE'S LAG TIME BEFORE CAR SHIFTS AND GETS GOING. ALSO THERE'S AN ONGOING (MONTH OR SO) DRONING NOISE. I TOOK CAR TO TOYOTA DEALER 6/15/06. SERVICE WRITER AND 2 TECHS HEARD DRONING NOISE WHILE I WAS THERE. WITH TH…
Read full complaint
A 2006 TOYOTA RAV4 V6 LIMITED 4X2. PROBLEM: AUTOMATIC TRANSMISSION DEFECT? SOMETIMES WHEN I STEP ON ACCELERATOR THERE'S LAG TIME BEFORE CAR SHIFTS AND GETS GOING. ALSO THERE'S AN ONGOING (MONTH OR SO) DRONING NOISE. I TOOK CAR TO TOYOTA DEALER 6/15/06. SERVICE WRITER AND 2 TECHS HEARD DRONING NOISE WHILE I WAS THERE. WITH THE CAR. I ASKED TO BRING THE CAR IN THE FOLLOWING SATURDAY AS I WORK DURING THE WEEK, BUT THEY SAID SATURDAYS NOT GOOD SO I MADE APPOINTMENT FOR 6/26/06. THEY TOLD ME IT WASN'T DANGEROUS TO DRIVE THE CAR. I TOOK CAR IN 6/26/06 & RODE WITH MASTER TECH WHO WAS ABLE TO HEAR THE DRONING NOISE. HE DROVE CAR, ALSO SAT IN PARKING LOT WITH ENGINE RUNNING AND SHIFTED INTO PARK AND INTO REVERSE ETC. WITH HIS FOOT ON THE BRAKE AND NOISE CHANGED IN INTENSITY IN DIFFERENT GEARS. HE TOOK CAR BACK TO SERVICE CENTER AND CHECKED IT OUT. THE SERVICE WRITER SAID THE TECH NOT ABLE TO PINPOINT PROBLEM, BUT TECH WOULD CALL TOYOTA ENGINEERING THE NEXT MORNING BECAUSE HE DIDN'T WANT TO TRY A FIX WHEN HE DIDN'T KNOW WHAT THE PROBLEM WAS. THEY GAVE ME MY CAR BACK, SAID THEY'D CALL ME AFTER TALKING TO TOYOTA ENGINEERING. THEY CALLED ME 6/27/06, SAID MASTER TECH HAD TALKED TO TOYOTA ENGINEERING AND THEY'VE HAD OTHER COMPLAINTS RE SAME DRONING NOISE, ARE WORKING TO FIND CAUSE SO THEY CAN CREATE A TSB AND EITHER REDUCE OR ELIMINATE THE NOISE. SERVICE WRITER TOLD ME T THERE IS NO TIMELINE FOR A FIX AND TO JUST "SIT TIGHT" AND WAIT UNTIL THEY CALL. THEY AGREE THE NOISE SHOULD NOT BE THERE. I'M WORRIED THAT ONGOING NOISE INDICATES THAT SOME PART IS OVERWORKING AND MAY WEAR OUT AND SINCE THE NOISE CHANGES IN INTENSITY SOMETIMES DEPENDING WHAT GEAR THE CAR IS IN I WORRY THAT IT IS THE TRANSMISSION AND THAT A FAILURE MAY RESULT. I DON'T UNDERSTAND HOW THEY CAN TELL ME THE VEHICLE IS SAFE TO DRIVE WHEN THEY CLAIM THEY DON'T KNOW WHAT THE PROBLEM IS. IT IS VERY UNSETTLING TO HAVE TO JUST WAIT FOR WHO KNOWS HOW LONG FOR THEM TO FIX THE PROBLEM. *NM
ERRATIC ACCELERATION WHICH CREATES HAZARDOUS SITUATIONS. SOMETIMES VEHICLE CONTINUES TO ACCELERATE WHEN ACCELERATOR PEDAL IS DEPRESSED, CAUSING UNPREDICTABLE BEHAVIOR WHICH LEADS TO DANGEROUS SITUATIONS. SOMETIMES VEHICLE ACCELERATES VERY RAPIDLY WITH VERY LITTLE PRESSURE ON ACCELERATOR PEDAL, WHICH IS HARD TO CONTROL IN A STOP …
Read full complaint
ERRATIC ACCELERATION WHICH CREATES HAZARDOUS SITUATIONS. SOMETIMES VEHICLE CONTINUES TO ACCELERATE WHEN ACCELERATOR PEDAL IS DEPRESSED, CAUSING UNPREDICTABLE BEHAVIOR WHICH LEADS TO DANGEROUS SITUATIONS. SOMETIMES VEHICLE ACCELERATES VERY RAPIDLY WITH VERY LITTLE PRESSURE ON ACCELERATOR PEDAL, WHICH IS HARD TO CONTROL IN A STOP AND GO TRAFFIC, I ALMOST HIT A CAR IN FRONT OF ME SEVERAL TIMES. SOMETIMES PRESSING ACCELERATOR PEDAL HAS NO REACTION FOR 1 TO 3 SECONDS, WHICH MAKES IT DIFFICULT TO PREDICT VEHICLE BEHAVIOR WHEN MERGING TO FASTER TRAFFIC. *JB
WINDSHIELD FOR THE TOYOTA RAV 4 ARE CRACKING VERY EASY. MINE HAS LESS THAN 3000 AND I HAVE ALREADY REPAIRED IT ONCE AND TODAY IT CRACKED AGAIN. THE DOT RATING IS NOT RIGHT DOT 20 . MY PONTIAC IS 147 AND HAS TAKEN MUCH BIGGER HITS AN NO DAMAGE. *NM
I HAVE A NEW 2006 TOYOTA RAV4 WITH AUTOMATIC TRANSMISSION AND, IN THE FIRST 2000 MILES, IT HAS FAILED TO SHIFT CORRECTLY ON 3 SEPARATE OCCASIONS. THIS HAS CREATED DANGEROUS SITUATIONS WHEN MERGING IN TRAFFIC. SPECIFICALLY, WHEN I STEP ON THE GAS PEDAL, THE RPMS SHOOT ABOVE 4-5K BUT THERE IS NO ACCOMPANIED INCREASE IN SPEED. G…
Read full complaint
I HAVE A NEW 2006 TOYOTA RAV4 WITH AUTOMATIC TRANSMISSION AND, IN THE FIRST 2000 MILES, IT HAS FAILED TO SHIFT CORRECTLY ON 3 SEPARATE OCCASIONS. THIS HAS CREATED DANGEROUS SITUATIONS WHEN MERGING IN TRAFFIC. SPECIFICALLY, WHEN I STEP ON THE GAS PEDAL, THE RPMS SHOOT ABOVE 4-5K BUT THERE IS NO ACCOMPANIED INCREASE IN SPEED. GIVEN THE REPEATED POSTINGS ON EDMUNDS.COM ABOUT THESE PROBLEMS, IT DOES NOT APPEAR TO BE AN ISOLATED CASE WITH MY VEHICLE. *JB
Official recalls
1116V596000 · Suspension:rear
Aug 12, 2016
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2011 Toyota RAV4 vehicles manufactured October 31, 2005, to September 7, 2010, and 2010 Lexus HS250h vehicles manufactured July 6, 2009, to August 26, 2010. The affected vehicles have rear suspension arms (rear tie rods) with adjusting lock nuts that may have been improperly tightened after servicing. As a result of being loose, the arm may have thread damage and may rust, possibly leading to the failure of the arm and an abrupt change in the vehicle's alignment.
Consequence & remedy
Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy: Toyota will notify owners and dealers will replace both rear suspension arms and encapsulate the locknuts, free of charge. The recall began on September 30, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's numbers for this recall are G0V for Toyota vehicles and GLK for Lexus vehicles. Note: This recall supersedes recall 13V-383, in which some vehicles were only inspected, sealed, and did not have both arms replaced. The affected vehicles were previously recalled under 13V-383, but did not have both rear suspension arms replaced at that time. Those vehicles need to have both arms replaced as part of this recall remedy.
16V396000 · Seats:front Assembly:seat Heater/cooler
Jun 2, 2016
Southeast Toyota Distributors, LLC (SET) is recalling certain 2005-2011 4Runner, Highlander, Sequoia, and Sienna, 2005-2010 Avalon and Tundra, 2006-2008 Camry Solara, 2006-2010 Highlander hybrid, 2006-2011 Rav4 and Tacoma, 2007-2010 FJ Cruiser, 2007-2011 Camry hybrid, 2009-2010 Venza, 2010-2012 Prius, 1988-1990 and 2005-2010 Camry, and 1989 and 2009-2010 Corolla vehicles equipped with aftermarket accessory seat heaters with a copper strand heating element. The electrical wiring in the seat heaters may be damaged when the seat cushion is compressed.
Consequence & remedy
Consequence: If damaged, the copper strand heating element may short circuit, increasing the risk of a fire.
Remedy: SET will notify owners, and dealers will disconnect the seat heaters, free of charge, and refund the purchase price of the seat heater accessory. The recall began on July 14, 2016. Owners may contact SET customer service at 1-866-405-4226. SET number for this recall is SET16B.
16V096000 · Seat Belts:rear/other
Feb 19, 2016
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain model year 2006-2012 RAV4 vehicles manufactured July 28, 2005, to December 19, 2012, and 2012-2014 RAV4 EV vehicles manufactured July 24, 2012, to August 29, 2014. In the event of a frontal collision, the rear seat belts for the outboard seats may be cut by the seat cushion frame.
Consequence & remedy
Consequence: A cut seat belt may not properly restrain the seat occupant, increasing their risk of injury in a crash.
Remedy: Toyota will notify owners, and dealers will install a protector over both rear seat cushion frames, free of charge. The recall began on June 24, 2016. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is G0F.
15V689000 · Visibility:power Window Devices And Controls
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
14V168000 · Air Bags:frontal:driver Side:inflator Module
Apr 9, 2014
Toyota is recalling certain model year 2006-2008 RAV4, 2006-2010 Yaris, 2008-2010 Highlander, and 2009-2010 Tacoma, Corolla, Corolla Matrix and General Motors Pontiac Vibe vehicles. In the affected vehicles, the steering column assembly contains electrical connections to the driver's airbag module housed in a spiral cable assembly, which includes a Flexible Flat Cable (FFC). Due to the shape and location of the FFC's retainer, the FFC could become damaged when the steering wheel is turned.
Consequence & remedy
Consequence: If the FFC is damaged, connectivity to the driver's air bag module could be lost and the air bag deactivated. The failure of the driver's air bag to deploy in the event of a crash that typically necessitates deployment increases the risk of injury to the driver.
Remedy: Toyota will notify the Toyota vehicle owners, and General Motors will notify the Pontiac Vibe owners. Toyota sent owners an interim notification letter in May 2014 to advise owners of the recall. Toyota will mail owners a second letter when remedy parts are available. General Motors sent Pontiac Vibe owners an Interim letter on June 20, 2014 notifying them that parts are currently unavailable. General Motors sent notices to the Pontiac Vibe owners on September 15, 2014, that a remedy is available. The recall began on October 27, 2014. Owners may contact Toyota at 1-800-331-4331. Owners may contact General Motors at 1-800-762-2737.
13V383000 · Suspension:rear
Aug 28, 2013
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust leading to thread damage and eventual failure. Failure of the rear tie rod will cause an abrupt change in the vehicle's alignment.
Consequence & remedy
Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will inspect the tie rods and replace any that have rust or corrosion on the alignment adjustment threads. All of the rear tie rods will then be encased in an epoxy to prevent future environmental damage. Due to limitations in parts, the recall remedy will be launched in phases from September 2013 through mid-April 2014. All owners will receive notification of the recall, with most receiving second notifications when parts are available in their area. IMPORTANT: This recall supersedes Toyota and Lexus recall 12V-373. All vehicles that have been inspected and remedied under the previous recall need to be re-inspected and have the appropriate remedy applied.
12V373000 · Suspension:rear
Aug 2, 2012
Toyota is recalling certain model year 2006 through 2011 RAV4 and 2010 Lexus HS250h passenger vehicles manufactured from October 2005 through September 2010. If the nuts for adjusting the rear wheel alignment are improperly tightened during service, the rear suspension arm (rear tie rod) may develop unwanted movement and rust, leading to thread damage and eventual failure. Failure of the rear tie rod will cause an abrupt change in the vehicle's alignment.
Consequence & remedy
Consequence: Failure of the rear tie rod could cause a loss of vehicle control, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will inspect the rear tie-rod nut for looseness and replace any suspect tie-rod found loose. Dealers will also affix instructions in multiple places to prevent improper servicing in the future. The recall began on November 30, 2012. Owners may contact Toyota at 1-800-331-4331 or Lexus at 1-800-255-3987.
11V113000 · Vehicle Speed Control:accelerator Pedal
Feb 24, 2011
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2008 THROUGH 2011 LEXUS LX570, 2003 THROUGH 2009 TOYOTA 4RUNNER, AND 2006 THROUGH 2010 RAV4 VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT.
Consequence & remedy
Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
Remedy: THE REMEDY IS NOW AVAILABLE. THE SAFETY RECALL BEGAN EARLY APRIL 2011. THE REMEDY WILL INVOLVE MODIFICATION OR REPLACEMENT OF THE ACCELERATOR PEDAL AND REPLACEMENT OF ANY TOYOTA ALL-WEATHER FLOOR MAT. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331 OR LEXUS AT 1-800-255-3987.
10V035000 · Equipment:other:labels
Feb 3, 2010
GULF STATES TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2010 VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD BETWEEN SEPTEMBER 1, 2005 AND JUNE 2, 2008 WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: THIS DOES NOT MEET THE STANDARD REQUIREMENTS.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. DEALERS WILL ALSO CORRECT THE OWNER'S MANUAL. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT GULF STATES TOYOTA AT 713-580-3300.
10V036000 · Equipment:other:labels
Feb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
09V223000 · Equipment:other:labels
Jun 15, 2009
TOYOTA IS RECALLING 27,080 MODEL YEAR 2005 THROUGH 2010 PASSENGER CARS BUILT FROM SEPTEMBER 1, 2005 TO MAY 4, 2009. THESE VEHICLES WERE NOT EQUIPPED WITH LOAD CARRYING CAPACITY MODIFICATION LABELS WHICH FAILS TO CONFORM WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS."
Consequence & remedy
Consequence: INCORRECT LOAD CARRYING CAPACITY MODIFICATION LABELS COULD RESULT IN THE VEHICLE BEING OVERLOADED, INCREASING THE RISK OF A CRASH.
Remedy: TOYOTA WILL NOTIFY OWNERS AND PROVIDE THEM WITH A NEW, ACCURATE LABEL TO BE INSTALLED OVER THE INACCURATE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON AUGUST 18, 2009. OWNERS MAY CONTACT TOYOTA AT 1-888-270-9371.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2PE12013 · Rear Suspension Arm Assembly Failure
Opened Jun 4, 2012 · Closed Sep 13, 2012
Status: closed (inferred from source dates) · Suspension; Suspension:rear
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
Additional source detail variants (4)
Suspension:rear
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
Suspension:rear
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
Suspension
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
Suspension
In a letter dated August 1, 2012 Toyota Motor Engineering & Manufacturing North America, Inc. (Toyota) submitted a Defect Information Report (NHTSA Recall No. 12V-373) to the NHTSA identifying a safety defect regarding possible separation of the Rear Suspension Arm No. 1 Assembly (arm) at the threaded portion (shaft and turn buckle) of the component in MY 2006 through MY 2011 Toyota RAV4 vehicles built from October 2005 through September 2010 and in MY 2010 Lexus HS250h vehicles manufactured from July 2009 through August 2010.According to Toyota, if the adjustment nuts for the rear wheel alignment are improperly tightened when alignment is performed in service, backlash may develop at the threaded portion of the arm, followed by rust formation.The threads may then wear causing the arm to separate, which may result in a loss of vehicle control.In analysis of both Vehicle Owner Questionnaire (VOQ) data submitted to the Office of Defects Investigation (ODI) and consumer complaint data submitted to Toyota, ODI identified 131 non-duplicative reports alleging failure of the subject rear suspension arm (Note:some of the complaints and related service records refer to the arm as a rear tie rod).Six of the complainants allege the failure resulted in some loss of vehicle control.For purposes of this analysis, loss of control events involve alleged complete or partial departure from the intended lane of travel.An additional four complaints reported difficulty maintaining control of the vehicle when the arm failed.Recalled vehicles will be inspected for proper torque of the adjustment nuts and replaced as necessary.In addition, Toyota will take several actions to reduce the potential for improper torque in future alignment procedures.This includes:(1) providing proper tightening sequence and torque specification information to two major wheel alignment equipment manufacturers, who would disseminate the information to alignment shops using their equipment; (2) installation of a clip on each arm with an instructional label showing proper tightening sequence and torque specification (the clip must be removed to perform a wheel alignment); (3) installation of additional labels on the front and back vertical surfaces of the Rear Suspension Arm No. 2 assemblies; and (4) providing an instruction booklet to owners to place in the glove box.This investigation is closed.
RQ10003 · Unintended And Uncontrolled Acceleration
Opened Feb 16, 2010 · Closed Mar 1, 2011
Status: closed (inferred from source dates) · Electrical System:software; Vehicle Speed Control:accelerator Pedal
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Additional source detail variants (6)
Electrical System:software
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Electrical System:software
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Electrical System:software
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Vehicle Speed Control:accelerator Pedal
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Vehicle Speed Control:accelerator Pedal
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.
Vehicle Speed Control:accelerator Pedal
On February 16, 2010, NHTSA's Office of Defects Investigation (ODI) opened RQ10-003 to determine whether the scope of prior Toyota recalls relating to potential unintended acceleration were sufficiently broad, including, among others, Toyota recalls 07E-082, 09V-388, 10V-017, and 10V-023.NHTSA also requested information regarding potential electronic causes of unintended acceleration in Toyota and Lexus vehicles.I. Pedal Interference from Floor mats, Carpet Covers and Plastic Pads in Carpets.During the RQ10-003 investigation, ODI reviewed a large volume of documents to assess whether additional vehicles should be recalled.Following the agency's analysis, NHTSA requested that Toyota recall additional vehicles.Toyota complied with the agency's request.The details of these recalls are set forth more fully in Toyota's reports to NHTSA pursuant to 49 CFR Part 573.These recalls are as follows:Recall 11V-112: (1) model year (MY) 2004-2006 Toyota Highlander and Highlander Hybrid; and, (2) MY 2004-2007 Lexus RX330,RX350, and RX400h (hybrid model). The total estimated population under this recall is 769,379 vehicles.This recall remedies potential accelerator pedal entrapment caused by a loose floor carpet cover (trim panel). Recall 11V-113: (1) MY 2003-2009 through 2009 Toyota 4Runner; (2) MY 2006-2010 Toyota RAV4; and, (3) MY 2008-2011 Lexus LX570.The total estimated population under this recall is 1,381,000 vehicles.This recall supplements recall 09V-388 and remedies potential accelerator pedal entrapment by an unsecured floor mat.Recall 11V-115: (1) MY 2006-2007 Lexus GS300 (all wheel drive vehicles); and, (2) MY 2006-2007 Lexus GS350 (all wheel drive vehicles). The total estimated population under this recall is 19,647 vehicles.This recall remedies potential accelerator pedal entrapment caused by inadequate clearance between the pedal linkage and a plastic pad embedded in the vehicle's carpet.II. Potential Electronic Causes of Unintended Acceleration.After NHTSA opened RQ10-003, NHTSA launched a ten-month study of potential electronic causes of unintended acceleration in Toyota vehicles.NHTSA launched the study in the spring of 2010 in light of concerns aired in Congressional hearings.NHTSA enlisted engineers at the National Aeronautics and Space Administration (NASA) with expertise in areas such as computer controlled electronic systems, electromagnetic interference and software integrity to assess whether electronic systems or electromagnetic interference played a role in incidents of unintended acceleration in Toyota vehicles.That study has concluded.Two reports are associated with the study and are available on NHTSA's website.NASA's report is entitled Technical Support to the National Highway Traffic Safety Administration (NHTSA) on the Reported Toyota Motor Corporation (TMC) Unintended Acceleration (UA) Investigation, NESC Assessment No. TI-10-00618 (Jan. 18, 2011).NHTSA's report is entitled Technical Assessment of Toyota Electronic Throttle Control (ETC) Systems (Feb. 2011).Both reports should be read in conjunction with each other. As stated in its report, NASA did not find an electronic cause of large throttle openings that can result in unintended acceleration incidents. NHTSA did not find a vehicle-based cause of unintended acceleration incidents other than the physical pedal interference causes that are being addressed by Toyota's recalls. This RQ is closed.