IllustrationWHILE TURNING THE WHEEL, THERE IS A LOUD POPPING NOISE. THE STEERING ASSEMBLY ALSO FEELS LOOSE WHEN TURNING. THIS HAPPENS AT ALL SPEEDS AND WHETHER TURNING LEFT OR RIGHT.
2012 Toyota Highlander
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2012 Toyota Highlander do not stand out strongly from the model-year median of 186.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Highlander years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
360–25K
2625–50K
3150–75K
1675–100K
15100–150K
3150K+
127 reports with mileage · 55 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 46 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 29 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Structure. Review the 20 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
16 crash reports3 fire reports5 injury reports
What owners actually said
182 reportsTHE DRIVER SEAT WINDOW IS GOING OFF TRACK. THE GLASS DOES NOT GO UP CORRECTLY AND HAS ALMOST LOOKED LIKE IT WAS GOING TO FALL OUT. THIS HAS HAPPENED WHILE DRIVING THE VEHICLE AND WITH THE VEHICLE STATIONARY.
WHILE TURNING STEERING COLUMN WAS MAKING LIGHT CLICKING NOISE FOR A FEW YEARS. IN 2019 CLICKING RATE AND VOLUME INCREASED AND WAS ACCOMPANIED BY A DEFINITE FEEL IN THE COLUMN. RESOLUTION WAS REPLACING INTERMEDIATE STEERING SHAFT AT A COST OF FOUR HUNDRED AND FORTY FOUR DOLLARS.
STEERING COLUMN MAKING TICKING SOUND. TOOK TO A MECHANIC AND HE STATED KNUCKLE JOINT IS BAD. HAPPENS WHEN DRIVING. POTENTIALLY COULD CAUSE STEERING TOFAIL
WHILE DRIVING ON THE FREEWAY AT 75 MPH I HEARD A VERY LOUD POPPING NOISE IN THE ROOF OF THE VEHICLE. WHEN I PULLED OFF ON A SIDE ROAD AT 45 MPH, THE SUNROOF EXPLODED, SOUNDING LIKE A SHOTGUN WAS FIRED OVER MY HEAD. THE COVER TO THE SUNROOF WAS OPEN AND TINY SHARDS OF GLASS FELL INTO THE CAR AND I WAS PICKING THEM OUT OF MY HAIR…
Read full complaint
WHILE DRIVING ON THE FREEWAY AT 75 MPH I HEARD A VERY LOUD POPPING NOISE IN THE ROOF OF THE VEHICLE. WHEN I PULLED OFF ON A SIDE ROAD AT 45 MPH, THE SUNROOF EXPLODED, SOUNDING LIKE A SHOTGUN WAS FIRED OVER MY HEAD. THE COVER TO THE SUNROOF WAS OPEN AND TINY SHARDS OF GLASS FELL INTO THE CAR AND I WAS PICKING THEM OUT OF MY HAIR ALL DAY. IT WAS VERY DISTRESSING AS I DIDN'T KNOW IF SOMEONE WAS SHOOTING AT ME SO I KEPT DRIVING UNTIL I WAS OUT OF THE AREA. WHEN I FELT SAFE, I STOPPED THE CAR TO INSPECT THE DAMAGE AND THAT'S WHEN I SAW THE SUNROOF GLASS PROTRUDING UPWARDS. THERE WERE NO OTHER CARS AROUND ME AND NOTHING OVERHEAD. IN THE ATTACHED PICTURE YOU CAN SEE THE GLASS OF THE SUNROOF PROTRUDING UPWARDS, WHICH COULD NOT BE THE RESULT OF AN IMPACT FROM OUTSIDE OF THE VEHICLE. WHEN I TOOK THE CAR TO THE TOYOTA DEALER, THE SERVICE MANAGER SAID HE'D HEARD OF IT HAPPENING BEFORE AND ADMITTED IT WAS A STRUCTURAL DEFECT, YET TOYOTA WOULD NOT COVER IT. HE SUGGESTED I SUBMIT A CLAIM TO MY INSURANCE, WHICH I DID. THIS IS A KNOWN ISSUE THAT TOYOTA NEEDS TO RECTIFY.
FOR SEVERAL MONTHS NOW I HAVE BEEN HEARING A CLUCKING NOISE WHEN TURNING THE STEERING WHEEL LEFT OR RIGHT AND UPON BREAKING A THUD SOUND IN THE FRONT OF MY CAR. AFTER TAKING MY CAR IN TO THE DEALERSHIP THEY CAME BACK AND SAID THAT THE NOISE WAS COMING FROM THE INTERMEDIATE SHAFT. I ASKED WELL HOW DO YOU DAMAGE A WHOLE INTERMEDIA…
Read full complaint
FOR SEVERAL MONTHS NOW I HAVE BEEN HEARING A CLUCKING NOISE WHEN TURNING THE STEERING WHEEL LEFT OR RIGHT AND UPON BREAKING A THUD SOUND IN THE FRONT OF MY CAR. AFTER TAKING MY CAR IN TO THE DEALERSHIP THEY CAME BACK AND SAID THAT THE NOISE WAS COMING FROM THE INTERMEDIATE SHAFT. I ASKED WELL HOW DO YOU DAMAGE A WHOLE INTERMEDIATE SHAFT? THEY SAID IT OCCURS OVER A PERIOD OF TIME. MY VEHICLE HAS 92,000 MILES ON IT BUT ITS BEEN MAINTAINED AND SERVICED AND NOT DRIVEN ROUGHLY BUT TO MAKE A LONG STORY SHORT THEY SAID IT WOULD COST ME ABOUT $615.00 TO HAVE THE VEHICLE REPAIRED PLUS AN ADDITIONAL $89.95 FOR THE ALIGNMENT. THIS APPEARS TO BE A MANUFACTURE ISSUE AND NEEDS TO HAVE A RECALL. I'M VERY DISAPPOINTED IN TOYOTA SINCE THEY PRIDE THEMSELVES AS BEING ONE OF THE LEADING AUTO MAKERS AROUND THE WORLD.
THE POWER DOOR LOCK ACTUATOR WENT OUT ON THE REAR PASSENGER DOOR IF MY 2012 TOYOTA HIGHLANDER. I ONLY NOTICED THE FAILURE BY CHANCE. AFTER MY SIX YEAR OLD SON GOT OUT OF THE CAR ONE DAY, I TRIED THE DOOR HANDLE AND NOTICED IT WAS UNLOCKED. I HIT THE KEY FOB LOCK BUTTON AGAIN, AND THE OTHER THREE DOORS LOCKED, BUT NOT THAT ONE…
Read full complaint
THE POWER DOOR LOCK ACTUATOR WENT OUT ON THE REAR PASSENGER DOOR IF MY 2012 TOYOTA HIGHLANDER. I ONLY NOTICED THE FAILURE BY CHANCE. AFTER MY SIX YEAR OLD SON GOT OUT OF THE CAR ONE DAY, I TRIED THE DOOR HANDLE AND NOTICED IT WAS UNLOCKED. I HIT THE KEY FOB LOCK BUTTON AGAIN, AND THE OTHER THREE DOORS LOCKED, BUT NOT THAT ONE. IT TURNS OUT, THE DOOR HAD NOT BEEN LOCKING FOR MONTHS. I PARK IN THE DRIVEWAY AT HOME, AND A REMOTE SURFACE LOT AT WORK, SO ESSENTIALLY THE CONTENTS OF MY VEHICLE HAVE BEEN WIDE OPEN TO THEFT FOR A LONG TIME. MORE SERIOUSLY, THE REAR PASSENGER DOOR WILL NOT UNLOCK WHEN THE TRANSMISSION IS PUT INTO PARK, OR THE UNLOCK BUTTON DEPRESSED. MY SON, WHO IS STILL IN A CAR SEAT WITH A FIVE-POINT SEATBELT, IS ESSENTIALLY TRAPPED IN THE VEHICLE. SOMEONE HAS TO OPEN THE FRONT PASSENGER DOOR, AND REACH PAST THE HEADREST TO MANUALLY UNLOCK THE REAR DOOR. IF YOU CONDUCT A LITTLE RESEARCH, YOU WILL SEE THIS IS A COMMON PROBLEM ON TOYOTA VEHICLES. IT COSTS $500 PER DOOR TO FIX AT THE DEALERSHIP. WHILE AUTOMATIC LOCKING MAY BE ONLY A CONVENIENCE ISSUE FOR OWNERS, FAILURE TO UNLOCK DOORS IS A MAJOR SAFETY ISSUE.
THE SEAL COATING ON THE ROOF PAINT CLEAR COAT IS UNDER CURRENT WARRANTEE AND THE DEALER WANTS NOT TO COVER IT. INSTEAD THEY WANT TO NOT USE THE POLICY ,BUT CHARGE ME $1000 FOR THEM TO PAINT IT.THIS I CONSUMER FRAUD.
WHILE OPERATING THE VEHICLE AND TRAVELING AT LESS THAN 20 MILES PER HOUR, A POPPING NOISE WAS PRESENT WHEN TURNING THE STEERING WHEEL IN EITHER DIRECTION. I TOOK IT TO A LOCAL MECHANIC AND IT WAS DIAGNOSED AS A INTERMEDIATE STEERING SHAFT PROBLEM AND WAS TOLD IT SHOULD BE REPLACED. THE PROBLEM WAS FIRST DETECTED AT ABOUT 55,00…
Read full complaint
WHILE OPERATING THE VEHICLE AND TRAVELING AT LESS THAN 20 MILES PER HOUR, A POPPING NOISE WAS PRESENT WHEN TURNING THE STEERING WHEEL IN EITHER DIRECTION. I TOOK IT TO A LOCAL MECHANIC AND IT WAS DIAGNOSED AS A INTERMEDIATE STEERING SHAFT PROBLEM AND WAS TOLD IT SHOULD BE REPLACED. THE PROBLEM WAS FIRST DETECTED AT ABOUT 55,000 MILES.
UPON TURNING STEERING WHEEL, EVEN SLIGHTLY, AN OBVIOUS "CLUNKING" NOISE IS HEARD AND FELT THROUGH THE STEERING COLUMN. THE MILEAGE ON THE CAR WAS APPROXIMATELY 62K. AT 70K I AM HAVING IT REPAIRED ALTHOUGH I WAS TOLD THERE WASN'T A SAFETY ISSUE. THE SOUND SEEMS TO HAVE INCREASED IN THE LAST 8K MILES.
Official recalls
213V123000 · Equipment:other:labels
Apr 9, 2013
Southeast Toyota is recalling certain model year 2008 and 2010-2013 Toyota Tundra, 2010-2012 Rav4, 2012 Toyota Sequoia, 2010-2011 Toyota Corolla, 2010-2011 Toyota Camry and Camry Hybrid, 2010-2013 Toyota Highlander and Highlander Hybrid, 2010-2013 Toyota FJ Cruiser, 2011 Toyota Land Cruiser, 2010-2013 Toyota Venza, 2010-2011 Toyota 4Runner, 2010-2013 Toyota Tacoma, 2011-2012 Toyota Sienna, 2012 Toyota Prius, 2013 Scion FR-S, 2011 Scion XD, 2011 Scion XB, and 2012 Scion TC vehicles. These vehicles were sold with labels that were outside the allowable one percent of accuracy of actual weight added. Thus, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) Number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An inaccurate label could lead to owners overloading their vehicles and tires. An overloaded vehicle can result in a tire failure which may result in a vehicle crash, personal injury, or property damage.
Remedy: Southeast Toyota will notify owners and provide a corrected label with instructions concerning its installation. A small group of the affected vehicles will need additonal remedies which are still being developed. The recall began on May 28, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
13V014000 · Air Bags:frontal:sensor/control MODULE-INACTIVE ; Seats
Jan 16, 2013
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence & remedy
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Additional source detail variants (2)
Seats
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Air Bags:frontal:sensor/control MODULE-INACTIVE
Southeast Toyota Distributors, LLC (SET) is recalling certain models interspersed through model years 2009 through 2013 as follows: model year 2009-2012 Tacoma, 4Runner, Camry, Camry Hybrid, Prius, and RAV4; model year 2009-2010 Avalon, FJ Cruiser, and Highlander Hybrid; model year 2010-2013 model year Corolla, Sienna and Tundra; model year 2009-2013 Highlander and Venza; model year 2012 Prius V; and model year 2010-2012 Sequoia. During modification by SET to include accessories such as leather seat covers, seat heaters or headrest DVD systems, these vehicles may not have had the passenger seat occupant sensing system calibration tested. Without passing the calibration test, the occupant sensing system may not operate as designed.
Consequence: If the front passenger seat occupant sensing system is out of calibration, the front passenger airbags may not deploy or they may deploy inappropriately for the passenger's size and position. This could increase the risk of personal injury during the event of a vehicle crash necessitating airbag deployment.
Remedy: Southeast Toyota will notify owners, and dealers will test the sensitivity of the occupant detection sensors, and recalibrate them as necessary. The recall began on March 21, 2013. Owners may contact Southeast Toyota at 1-800-301-6859.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
2EA18006 · Steering Column Separation
Opened Nov 16, 2018 · Closed Apr 2, 2024
Status: closed (inferred from source dates) · Steering; Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Steering:column
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Steering
On November 16, 2018, the Office of Defects Investigation (ODI) opened an Engineering Analysis (EA18-006) as an upgrade to a Preliminary Evaluation (PE18-005). The investigation focused on allegations of steering wheel separation from the lower steering column after using the tilt and/or telescoping mechanism. Given the separation occurring when operating the tilt and/or telescoping function and failure of both shear capsules to maintain the lower steering column mounting position, potential for shear capsule damage in the known failures due to collisions, the overall low rate of occurrence, and the updated manufacturer documentation, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that no safety-related defect exists. The agency reserves right to take further action if warranted by the circumstances. A detailed summary of the investigation is attached to this closing resume. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18005 · Upper Steering Column Separation
Opened May 4, 2018 · Closed Nov 20, 2018
Status: closed (inferred from source dates) · Steering; Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Additional source detail variants (2)
Steering:column
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.
Steering
On May 4, 2018, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18-005 to investigate three allegations of steering column separation for Model Year (MY) 2008 through 2013 Toyota Highlander vehicles. Two (2) of the 3 complaints were received by ODI in April 2018 and occurred while the vehicle was in motion. Since opening PE18-005, one (1) additional VOQ involving steering column separation has been received. This incident occurred while the vehicle was stationary.As part of PE18-005, ODI examined the field data, warranty data, and relevant technical information submitted by Toyota in response to the PE18-005 information request letter. Ten (10) additional incidents of steering column separation were identified. Four (4) of these instances occurred while driving. During PE18-005, ODI confirmed that the steering columns in the subject vehicles are equipped with breakaway capsules that are designed to collapse/shear during certain types of vehicle collisions. This design feature aims to reduce driver injury severity from impact with the steering wheel in frontal vehicle collisions. There is no direct method for detecting when the capsules in the subject vehicles have sheared. If the driver operates the tilt/telescoping feature after the breakaway capsules have separated, the steering column may drop out of position and could subsequently detach entirely from the rest of the steering assembly. Loss of steering while driving may cause a loss of vehicle control, which could lead to a vehicle crash.To date, ODI has identified 14 incidents involving complete steering column separation, 6 of which occurred while driving. One of these incidents involved a minor crash. Additionally, there have been 16 events where the steering column dropped from the dashboard mounting brackets, but column separation did not occur. Four of these incidents happened while driving. Of these 30 total separation/drop incidents, 5 of the vehicles have evidence of minor collision repairs months or years prior to the steering column failure.This investigation has been upgraded an to Engineering Analysis (EA18-006) in order to 1) conduct a more detailed analysis of the conditions that may cause the steering column breakaway capsules to separate and 2) assess factors that may contribute to the problem of failing to detect and repair breakaway capsules after they have separated. Toyota has recently revised their repair manual and issued a Collision Repair Information Bulletin to help address the second concern.The VOQs associated with this investigation can be viewed at www.NHTSA.gov under the following ODI complaint numbers: 11141761, 11083623, 11083280, 10888043.