Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
410–25K
925–50K
250–75K
275–100K
1100–150K
0150K+
55 reports with mileage · 147 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Power Train. Review the 54 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Engine. Review the 39 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Air Bags. Review the 31 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
23 crash reports1 fire reports10 injury reports
What owners actually said
202 reports
Mileage unknown · Sep 16, 2026
Power Train
Component that failed was the CSC Concentric Slave Cylinder. I went to press the clutch and it stuck to the floor. I checked for leaks in the cabin beneath the clutch and it was dry. I then proceeded to check the reservoir and saw that it needed fluid. I managed to get it to a nearby convenience center to purchase and fill the r…
Read full complaint
Component that failed was the CSC Concentric Slave Cylinder. I went to press the clutch and it stuck to the floor. I checked for leaks in the cabin beneath the clutch and it was dry. I then proceeded to check the reservoir and saw that it needed fluid. I managed to get it to a nearby convenience center to purchase and fill the reservoir when that did not work I called a tow truck to move it to an auto repair shop. This put others at risk, should the clutch have remained in neutral I would have, and or all the break fluid would have leaked and i would have been without brakes since the clutch and break share a reservoir. This issue could have caused serious life threatening injuries not only to myself but others had there been an accident. Thankfully this took place at 4 am before other drives were out and about for the morning commute. The component has since been looked at by an independent service center. There were no warning lamps or messages prior to the issue. the vehicle currently has roughlty 84,000 miles.
NHTSA ODI #11764719
Mileage unknown · Sep 10, 2026
Power Train
Slave cylinder on clutch failed and leaked fluid in to clutch and flywheel. Clutch pedal would not rebound after being pressed in to shift gear, stuck in middle of road trying to get vehicle in first gear. Had vehicle towed to dealership, estimate of $5800 to repair. Apparently this is a known problem with this manual transmis…
Read full complaint
Slave cylinder on clutch failed and leaked fluid in to clutch and flywheel. Clutch pedal would not rebound after being pressed in to shift gear, stuck in middle of road trying to get vehicle in first gear. Had vehicle towed to dealership, estimate of $5800 to repair. Apparently this is a known problem with this manual transmission, many others have experienced similar failure at around 60,000 miles.
NHTSA ODI #11763432
46,091 miles · Aug 4, 2026
Electrical System
Odometer Fraud. The contact purchased a 2019 Toyota Corolla. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. At the time of purchase, the vehicle mileage was 45,709, and at the time of registration, it was discovered that the…
Read full complaint
Odometer Fraud. The contact purchased a 2019 Toyota Corolla. The contact stated that while attempting to register the vehicle, it was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. At the time of purchase, the vehicle mileage was 45,709, and at the time of registration, it was discovered that the mileage listed on the title was 46,091. Additionally, the contact later became aware that the vehicle was a salvaged vehicle. The seller was contacted several times but blocked all communications.
NHTSA ODI #11754726
75,000 miles · Jun 17, 2026
Electrical SystemTires
The contact owns a 2019 Toyota Corolla. The contact stated that while driving at an undisclosed speed, the low tire pressure warning light illuminated, with several other unknown warning lights illuminated. The vehicle was taken to an independent mechanic to be diagnosed. However, the independent mechanic stated that the tire pr…
Read full complaint
The contact owns a 2019 Toyota Corolla. The contact stated that while driving at an undisclosed speed, the low tire pressure warning light illuminated, with several other unknown warning lights illuminated. The vehicle was taken to an independent mechanic to be diagnosed. However, the independent mechanic stated that the tire pressures were not low, and that the cause of the failure was not determined. The vehicle was not repaired. The manufacturer was not notified of the failure. The failure mileage was approximately 75,000.
NHTSA ODI #11744710
Mileage unknown · May 4, 2026
Air BagsCrash
I was driving on a two lane state road. Two vehicles we traveling in front of me in the left lane. The further vehicle in left decide to make a sudden stop at a traffic light. The silver sedan behind that vehicle was traveling too close to react appropriately. The sedan avoid the vehicle in front of it and impeded into my lane a…
Read full complaint
I was driving on a two lane state road. Two vehicles we traveling in front of me in the left lane. The further vehicle in left decide to make a sudden stop at a traffic light. The silver sedan behind that vehicle was traveling too close to react appropriately. The sedan avoid the vehicle in front of it and impeded into my lane and collide with my vehicle. My airbags in my 2019 Corolla failed to deploy.
NHTSA ODI #11735650
Mileage unknown · Apr 11, 2026
Power Train
Premature slave cylinder failure at ~70k miles. Suddenly started leaking brake fluid profusely. Inspected and confirmed by Toyota dealership. No symptoms prior to failure. Clutch stopped functioning, unable to shift while driving. Pulled over to inspect and all of the brake fluid had leaked out. Refilled brake fluid and bled sy…
Read full complaint
Premature slave cylinder failure at ~70k miles. Suddenly started leaking brake fluid profusely. Inspected and confirmed by Toyota dealership. No symptoms prior to failure. Clutch stopped functioning, unable to shift while driving. Pulled over to inspect and all of the brake fluid had leaked out. Refilled brake fluid and bled system, reservoir leaked to minimum fill line within 24 hours.
NHTSA ODI #11730580
Mileage unknown · Apr 7, 2026
Power Train
DESCRIPTION OF SAFETY ISSUE: The Concentric Slave Cylinder (CSC) on my 2019 Toyota Corolla Hatchback 6-speed manual failed during normal driving at around 60mph, creating an immediate and uncontrolled safety hazard. The clutch pedal depressed fully to the floor while I was shifting from 5th gear to 6th gear and the vehicle beca…
Read full complaint
DESCRIPTION OF SAFETY ISSUE: The Concentric Slave Cylinder (CSC) on my 2019 Toyota Corolla Hatchback 6-speed manual failed during normal driving at around 60mph, creating an immediate and uncontrolled safety hazard. The clutch pedal depressed fully to the floor while I was shifting from 5th gear to 6th gear and the vehicle became unable to be shifted out of gear, leaving me unable to properly control vehicle speed or movement. The only way to release the transmission was to physically reach down and lift the clutch pedal up with my foot while attempting to drive. CRITICAL SAFETY CONCERN - SHARED BRAKE AND CLUTCH FLUID RESERVOIR: On this vehicle, the brake fluid reservoir and clutch hydraulic system share a single reservoir. When the CSC fails and leaks fluid, brake fluid is consumed directly from the same reservoir that supplies the braking system. A CSC failure does not only result in loss of clutch function — it results in loss of brake fluid, and with sufficient fluid loss, partial or complete brake failure. This is not a theoretical risk. This vehicle can fail in a way that simultaneously removes the driver's ability to control vehicle speed via the transmission AND reduces or eliminates braking capability — both at the same time, without warning I am requesting that NHTSA investigate this as a safety defect and consider whether a recall or service campaign is warranted given the risk of simultaneous clutch and brake failure on these vehicles.
NHTSA ODI #11729790
Mileage unknown · Apr 2, 2026
Power Train
6 speed manual transmission. 79K miles. Vehicle was checked at a dealer due to a sluggish clutch. Dealer found low brake fluid, but no problems with the clutch. The next day the clutch failed completely and car had to be towed off the highway. Slave cylinder for the clutch is a design flaw on these vehicles.
NHTSA ODI #11728777
Mileage unknown · Mar 28, 2026
Power Train
Clutch release bearing/slave cylinder failed at 29,900 miles. Without warning or unusual symptoms, clutch pedal stuck to floor and was unable to shift gears without manually pulling clutch pedal up.
NHTSA ODI #11727668
Mileage unknown · Mar 27, 2026
Power Train
The clutch slave cylinder in my 2019 Toyota Corolla Hatchback failed, causing brake fluid to leak out. The leaking fluid contaminated the clutch assembly, resulting in both the slave cylinder and clutch needing replacement. The failed components should be available for inspection from the repair facility upon request. The failur…
Read full complaint
The clutch slave cylinder in my 2019 Toyota Corolla Hatchback failed, causing brake fluid to leak out. The leaking fluid contaminated the clutch assembly, resulting in both the slave cylinder and clutch needing replacement. The failed components should be available for inspection from the repair facility upon request. The failure led to a loss of proper clutch operation, which made it difficult to shift gears and control the vehicle. This created a risk of stalling in traffic or being unable to accelerate when needed, increasing the potential for a collision, especially in busy or high-speed driving conditions. Yes, the issue was diagnosed and confirmed by the dealership. They identified the failed slave cylinder and verified that brake fluid leakage caused contamination of the clutch, requiring replacement of both components. The vehicle has been inspected by a service technician/mechanic at the Toyota dealership. Prior to the failure, there were no warning lights or dashboard messages indicating a problem. The issue appeared suddenly when the clutch began to malfunction due to the fluid leak causing me to not be able to shift gears and the clutch pedal not returning.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2011-2019 Corolla, 2011-2013 Matrix, 2012-2018 Avalon, and 2013-2018 Avalon Hybrid vehicles. During certain crashes, the air bag electronic control unit (ECU) may malfunction, possibly disabling the deployment of the air bags and/or seat belt pretensioners.
Consequence & remedy
Consequence: In the event of a crash, air bags and/or seat belt pretensioners that do not deploy as intended may increase the risk of injury.
Remedy: Toyota will notify owners, and dealers will inspect the ECU and install a noise filter between the air bag control module and its wire harness, as necessary, free of charge. Owners were notified of the safety risk beginning March 2, 2020. A second letter notifying owners of the remedy repair will be mailed between March 16, 2020 and June 27, 2020. Owners may contact Toyota customer service at 1-888-270-9371. Toyota's numbers for this recall are 20TB03, 20TA03 and 20TA05.
Toyota Motor Engineering & Manufacturing (Toyota) recalled certain 2018-2019 4Runner, Highlander, Camry, Land Cruiser, Sequoia, Sienna, Tacoma and Tundra, and Lexus RC 300, RC 350, GS 350, GX 460, IS 300, LC 500, LS 500, LX 570, RX 350L, and 2019 Toyota Avalon and Corolla, and certain Lexus NX 300, and ES 350 vehicles on January 13, 2020. On March 4, 2020, Toyota expanded the recall to include certain 2014-2015 Toyota 4Runner and Land Cruiser, 2018 Avalon, Corolla, 2014 FJ Cruiser, 2017 Sienna and Lexus 2018 ES 350, 2018-2019 GS 300, 2013-2014 GS350, 2014-2015 GX 460, IS 350 and LX 570, 2014 IS F, 2018-2019 IS 350, LC 500H and LS 500H, 2013-2015 LS 460, 2015 NX 200T and RC350, 2017 RC 200T and RX 350. Toyota also removed the 2018-2019 Toyota 4Runner and Land Cruiser and 2018-2019 Lexus GX 460 and LX 570 and 2019 NX300 from inclusion in this recall. On March 19, 2020, Toyota expanded the recall to include 2015 Lexus GS350 vehicles. The low-pressure fuel pump inside the fuel tank may fail.
Consequence & remedy
Consequence: If the fuel pump fails, the engine can stall while driving, increasing the risk of a crash.
Remedy: Toyota will notify owners, and dealers will replace the fuel pump, free of charge. The recall began May 4, 2020. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are 20TB02 and 20TA02 for Toyota vehicles and 20LB01 and 20LA01 for Lexus vehicles.
Southeast Toyota Distributors, LLC (SET) is recalling certain 2017-2019 Toyota Camry, Corolla, Rav4, Sienna, and Yaris iA vehicles equipped with factory-installed floor mats. The load carrying capacity modification label may be incorrect. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: An incorrect label may lead to unintentionally overloading the vehicle, increasing the risk of a crash.
Remedy: SET will notify owners and provide a corrected label for placement over the inaccurate label, free of charge. The recall began August 23, 2019. Owners may contact Toyota customer service at 1-888-270-9371. SET's number for this recall is SET19A.
Gulf States Toyota (GST) is recalling certain 2019 C-HR, 4Runner, Avalon, Avalon Hybrid, Camry, Camry Hybrid, Highlander, Land Cruiser, Prius, RAV4, Sequoia, Tacoma, Sienna, Tundra and Yaris vehicles. The text on the load capacity label may become illegible. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 110, "Tire Selection and Rims."
Consequence & remedy
Consequence: If the driver cannot read the label, they may unknowingly overload the vehicle, increasing the risk of a crash.
Remedy: GST will notify owners, and dealers will provide corrected load carrying capacity modification labels, free of charge. The recall began May 24, 2019. Owners may contact GST customer service at 1-800-444-1074. GST's number for this recall is 19R1.
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2019 Toyota Corolla hatchback vehicles equipped with Continuously Variable Transmissions (CVT). The pump impeller blades within the torque converter may detach, especially when driven under high load, potentially causing a vehicle stall.
Consequence & remedy
Consequence: A vehicle stall, especially when driving a high rate of speed, can increase the risk of a crash.
Remedy: Toyota has notified owners, and dealers will replace the CVT and torque converter, free of charge. The recall began April 22, 2019. Owners may contact Toyota customer service at 1-888-270-9371. Toyota's number for this recall is J17/J07.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA19001 · Electrical Overstress
Opened Apr 19, 2019 · Closed Sep 19, 2024
Status: closed (inferred from source dates) · Air Bags: Air Bag/restraint Control Module
The Office of Defects Investigation (ODI) opened this investigation to determine if the failure of airbags to deploy during severe crashes, in certain vehicles, was the result of a safety related defect. During the investigation a complex failure was studied that can result in non-deployment of subject vehicle air bags and other restraint system devices in severe crash events. The subject vehicles may be equipped with an airbag control unit (ACU) for the supplemental restraint system (SRS) Electronic Control Unit (ECU) manufactured by ZF-TRW. The ECU receives signals from crash sensors mounted in the vehicle and deploys the vehicle air bags and seat belt pretensioners in accordance with manufacturer design specifications. The ECU in the subject vehicles contains a model DS84 application-specific integrated circuit (ASIC) which controls the communication of the crash sensor signal, firing commands (i.e., when to deploy the airbag(s) and/or pretensioners), and fault information (e.g., diagnostic trouble codes). In September 2016, FCA announced recall 16V-668 for certain model year (MY) 2010 to 2014 Chrysler, Dodge and Jeep products manufactured with the subject ZF-TRW ACU. In this recall, FCA discussed an EOS condition that resulted in a failure of the subject DS84 ASIC, which caused air bag non-deployment. FCA noted that the defect condition had only been observed in vehicles equipped with sensor harnessing routed across the front of the vehicle. Other FCA vehicles that also used the subject ACU, but were not equipped with cross-car harnessing, had not experienced EOS failures, despite similar time in service. During the course of this investigation, ODI sent two separate Information Request (IR) letters to six vehicle manufactures (including FCA, Hyundai, Honda, Kia, Mitsubishi, and Toyota) and one IR letter to ZF-TRW. These IR letters resulted in ODI receiving comprehensive data from these manufacturers and suppliers. Studies of this data found that the DS84 ASIC does not have sufficient protection against negative electrical transients or electrical overstress (“EOS”) that can be generated in certain severe crashes. An electrical transient occurs when the electrical power supplied to a circuit changes momentarily over a short duration of time. In these severe crash cases, the crash sensors and other powered wiring can be damaged and short circuited so as to create a negative electrical transient of sufficient intensity and duration (that are outside the vehicle manufacturer's specification) to damage the ASIC before the restraint device deployment signal is received by the SRS ECU. This damaged signal can lead to incomplete or nondeployment of the air bags and/or pretensioners. Airbag non-deployment and/or lack of pretensioner operation can increase the risk or severity of injury in a crash.A total of 8 fatalities and 14 injuries were associated with known EOS events. The common element in all investigated manufacturers vehicles is the SRS ECU containing a DS84 ASIC manufactured by ZF-TRW. The risk associated with the ASIC is equally shared among all OEMS involved in the investigation. The actual real-world risk can be mitigated by other factors which were assessed by ODI during this investigation. The first mitigating factor involves protections built into the ACU design which protect the DS84 ASIC from damage. There are multiple strategies and levels of protection employed by different OEMs that provide effective EOS mitigation. The two most common strategies at the ACU level are circuit protection diodes on the remote senor signal lines, and current limiting resistors that protect critical components. The second mitigating factor is found at the vehicle level and involves the location and routing of the wires leading from the crash sensors to the SRS ECU. If the wires are well protected in a crash and are not routed with other power wires carrying large currents, the risk for an EOS event is significantly reduced or eliminated. These design specific factors combine to produce a spectrum of risk for the vehicles equipped with ACUs using the DS84 ASIC. Given the many of years of field exposure, it is possible to divide the subject population into two groups; vehicles which have experienced EOS events, and vehicles which have not experienced EOS field events. Four of the six OEMs involved in this investigation have experienced EOS field events on at least one of their models equipped with a DS84 ASIC. All vehicle models (including the Toyota models identified in the Failure Report Summary of the opening resume for this investigation) with field events have been recalled. In an abundance of caution, ODI kept this investigation open five years to monitor field performance and did not identify any field events on vehicles not included in existing safety recalls. Given the spectrum of risk identified in this investigation and that all vehicles with a demonstrated unreasonable risk have been recalled, ODI is closing this investigation. ODI is closing this investigation with the following manufacturer safety recalls: 16V-668, 18E-043, 18V-137, 18V-363, and 20V-024. With the recall actions taken by the subject vehicle and equipment manufacturers, this investigation is closed. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exists on other model or model year vehicles outside of the recall scopes. The agency reserves the right to take further action if warranted by the circumstances.
Illustration