MY STEERING WHEEL HAS LOCKED ON ME A COUPLE OF TIMES IT JUST DID IT AGAIN AS I WAS ON A RED LIGHT ALSO AS I WAS PARKING. CAN U LET ME KNOW ANY INFO. MY NUMBER IS [XXX]. INFORMATION Redacted PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).
2007 Toyota Corolla
Owner reports · Recalls · Investigations
More warning signs than most Corolla years
Owner complaints for the 2007 Toyota Corolla are substantially higher than the model-year median of 129.
About this comparison →How this year compares
Owner complaints by model year
Compare all Corolla years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
417 reports with mileage · 419 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 436 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 95 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 89 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
836 reportsTL* THE CONTACT OWNS A 2007 TOYOTA COROLLA. WHEN THE CONTACT STARTED THE VEHICLE IN THE DRIVEWAY AND DEPRESSED THE ACCELERATOR PEDAL, THE VEHICLE SURGED WITH A HIGH RATE OF SPEED AND CRASHED INTO THE GARAGE. THE AIR BAGS DID NOT DEPLOY. THERE WERE NO INJURIES. THE INSURANCE COMPANY HAD THE VEHICLE TOWED AND WAS TO HAVE A FACILIT…
Read full complaint
TL* THE CONTACT OWNS A 2007 TOYOTA COROLLA. WHEN THE CONTACT STARTED THE VEHICLE IN THE DRIVEWAY AND DEPRESSED THE ACCELERATOR PEDAL, THE VEHICLE SURGED WITH A HIGH RATE OF SPEED AND CRASHED INTO THE GARAGE. THE AIR BAGS DID NOT DEPLOY. THERE WERE NO INJURIES. THE INSURANCE COMPANY HAD THE VEHICLE TOWED AND WAS TO HAVE A FACILITY INSPECT THE VEHICLE. THE VEHICLE WAS NOT DIAGNOSED. THE DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS NOTIFIED. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 130,000. *TT CONSUMER STATED UNINTENDED ACCELERATION AT GREAT SPEED.*JB
TAKATA RECALLON BUT THIS IS NOT UNDER THE RECALL, BUT I DID SEE IT THERE WERE RECALLED IN EUROPE JUST THE OTHER DAY FOR NOT GOING OFF AS WELL AS GOING OFF WITHOUT BEING HIT. I JUST WISH MINE HAD GONE OFF. 09/23/2018 I WAS HIT HEADON BY A VEHICLE GOING 45 MPH. THERE WAS NO WHERE ON MY FRONT END THAT WAS NOT EFFECTED BY THE ACCIDE…
Read full complaint
TAKATA RECALLON BUT THIS IS NOT UNDER THE RECALL, BUT I DID SEE IT THERE WERE RECALLED IN EUROPE JUST THE OTHER DAY FOR NOT GOING OFF AS WELL AS GOING OFF WITHOUT BEING HIT. I JUST WISH MINE HAD GONE OFF. 09/23/2018 I WAS HIT HEADON BY A VEHICLE GOING 45 MPH. THERE WAS NO WHERE ON MY FRONT END THAT WAS NOT EFFECTED BY THE ACCIDENT. RESEARCHING I FOUND WHERE THE SENSORS WERE FOR THE AIR BAG, EACH ON EACH SIDE OF THE RADITOR WAS HIT. THE AIR BAG DID NOT DEFLATE CASING MYSELF NECK AND BACK INJURY THAT WILL NEVER REPAIR. PICTURES WILL SHOW THAT THERE IS NO WAY NONE OF THE AIR BAG SENSORS WERE NOT DAMAGED OR HIT TO ADVISE THE AIR BAG TO GO OFF AND HOLD THE PERSON IN PLACE SO THEY DO NOT GET SLUNG AROUND LIKE A RAG DOLL UNTIL THE ACCIDENT IS OVER. I REMEMBER SEEING THAT THE ACCIDENT WAS GOING TO HAPPEN, I JUST DID NOT THINK I WOULD OF BEEN INVOLVED IN IT. UNFORTUNATELY, A TRUCK HIT ANOTHER VEHICLE WHICH THAT VEHICLE SLAMMED INTO ME AT FULL FORCE. I FIRST WAS SLUNG INTO THE DOOR, THE NEXT THING I REMEMBER IS MY ACCELERATOR STICKING SO I HAD TO TURN OFF MY KEY TO AVOID FLYING ACROSS A BUSY ROAD. I HAVE A BULDGING DISC, DAMAGED TENDONS AND MUSCLES. I AM 61 YEARS OLD AND NOW FEAR THAT IF HIT EVER AGAIN THE AIR BAG WILL NOT DEPLOY.
TL* THE CONTACT OWNS A 2007 TOYOTA COROLLA. WHILE STARTING THE VEHICLE, THE DRIVER'S SIDE AIR BAG WARNING INDICATOR ILLUMINATED. THE CONTACT STATED THAT THE WARNING INDICATOR REMAINED ILLUMINATED WHILE DRIVING, WHICH WAS A SAFETY CONCERN. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE CLOCKSPRIN…
Read full complaint
TL* THE CONTACT OWNS A 2007 TOYOTA COROLLA. WHILE STARTING THE VEHICLE, THE DRIVER'S SIDE AIR BAG WARNING INDICATOR ILLUMINATED. THE CONTACT STATED THAT THE WARNING INDICATOR REMAINED ILLUMINATED WHILE DRIVING, WHICH WAS A SAFETY CONCERN. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC WHERE IT WAS DIAGNOSED THAT THE CLOCKSPRING AND THE AIR BAGS NEEDED TO BE REPLACED. THE VEHICLE WAS TAKEN TO EAST STREET AUTO (746 EAST ST, PITTSFIELD, MA 01201, (413) 443-3447) WHERE IT WAS REPAIRED. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS APPROXIMATELY 104,000.
SATURDAY, JUNE 2. THE DRIVER'S AIRBAG LIGHT CAME ON INTERMITTENTLY WHILE I WAS DRIVING MY 2007 TOYOTA COROLLA. I IMMEDIATELY TOOK MY VEHICLE TO THE LOCAL TOYOTA DEALER. THE DIAGNOSIS WAS INTERMITTENT OPEN CIRCUIT IN THE SPIRAL CABLE. I READ ON THE NHTSA WEBSITE THAT THIS IS A PROBLEM WITH OTHER TOYOTA MODELS AND YEARS AND THAT…
Read full complaint
SATURDAY, JUNE 2. THE DRIVER'S AIRBAG LIGHT CAME ON INTERMITTENTLY WHILE I WAS DRIVING MY 2007 TOYOTA COROLLA. I IMMEDIATELY TOOK MY VEHICLE TO THE LOCAL TOYOTA DEALER. THE DIAGNOSIS WAS INTERMITTENT OPEN CIRCUIT IN THE SPIRAL CABLE. I READ ON THE NHTSA WEBSITE THAT THIS IS A PROBLEM WITH OTHER TOYOTA MODELS AND YEARS AND THAT A RECALL NOTICE WAS SENT TO OWNERS AND REPAIRS WERE MADE AT NO COST TO THE CONSUMER. TUESDAY, JUNE 5. THE DEFECTIVE PART WAS REPLACED AND I WAS TOLD THAT TOYOTA WOULD NOT PAY FOR THE PARTS AND LABOR. I SPOKE WITH THE DIRECTOR OF PARTS AND SERVICE TO ASK WHY I WAS CHARGED FOR THE REPAIR. HE SAID THE SPIRAL CABLE WAS NOT RELATED DIRECTLY TO THE AIRBAG, SO IT IS NOT A RECALL ISSUE; IT'S A PART THAT WEARS OUT, LIKE A WORN-OUT TIRE OR BRAKE PADS THAT ONE WOULD NEED TO REPLACE. I TOLD HIM THAT OTHER TOYOTA VEHICLES WITH DEFECTIVE SPIRAL CABLES WERE REPAIRED AT NO COST TO THE CONSUMER. HE SAID THAT THERE WAS NOTHING HE COULD DO TO HELP BECAUSE IT WAS OUT OF HIS HANDS AND THAT I WOULD NEED TO CALL THE 800 NUMBER FOR CUSTOMER SERVICE. JUNE 6. I CALLED CUSTOMER SERVICE AND EXPLAINED MY CONCERN. THE REPRESENTATIVE WHO TOOK MY INFORMATION SAID THAT I WOULD GET A CALL BACK IN A DAY AFTER HE RESEARCHED THE SITUATION. THURSDAY, JUNE 7. I RECEIVED A CALL FROM CUSTOMER SERVICE INFORMING ME THAT MY REQUEST FOR TOYOTA TO PAY THE FOR THE REPAIR WAS DENIED. THIS IS OBVIOUSLY A SAFETY-RELATED DEFECT AS OTHER VEHICLES WERE RECALLED FOR THE SAME REASON. I WAS TOLD I COULD DRIVE MY VEHICLE WITHOUT THE DEFECTIVE PART REPLACED, BUT I DIDN'T HAVE PEACE OF MIND THAT IT WOULD BE SAFE TO ME OR TO OTHERS IN THE EVENT OF AN ACCIDENT WHILE DRIVING; I NEEDED TO BE ASSURED THAT THE AIRBAG WOULD DEPLOY UNDER CONDITIONS IT IS MEANT TO DEPLOY. TOYOTA SHOULD REIMBURSE ME FOR THE TOTAL COST AS THE AIRBAG DID NOT MEET THE STANDARDS TO SAFELY OPERATE MY VEHICLE.
TAKATA INFLATORS I HAVEN'T HAD AN ISSUE WITH MY AIRBAGS YET, BUT I SAW A NEWS ARTICLE THAT THERE ARE PROBLEM WITH MAKERS OF MOST CAR COMPANY'S AIRBAGS AND MY CAR WAS ON OF THE MODELS.
TAKATA RECALL, AIR BAG LIGHT WONT GO OUT
AFTER HAVING MY CAR SERVICED FOR THE RECALL, I NOTICED THE DRIVERS SIDE AIR BAG RED LIGHT DISPLAYED. SHOWING THAT MY DRIVERS SIDE AIRBAG HAS EITHER BEEN TURNED OFF OR MALFUNCTIONED. THIS IS A HUGE CONCERN FOR THE SAFETY OF MYSELF AND OTHERS WHO HAVE PERMISSION TO DRIVE MY VEHICLE.
PARKING MY COROLLA I PUT THE CAR IN REVERSE LIGHTLY DEPRESSED ACCELERATOR PEDAL TO REVERSE THE VEHICLE. THE VEHICLE SURGED IN REVERSE.I WAS ABLE TO STOP THE CAR BY STEPPING ON THE BRAKE AND MOVING GEAR SHIFTER TO NEUTRAL PREVENTING CAR FROM HITTING FENCE.THIS VEHICLE HAD THE ECM REPLACED FOR A PREVIOUS RECALL ON 6-18-11 ON THE 1…
Read full complaint
PARKING MY COROLLA I PUT THE CAR IN REVERSE LIGHTLY DEPRESSED ACCELERATOR PEDAL TO REVERSE THE VEHICLE. THE VEHICLE SURGED IN REVERSE.I WAS ABLE TO STOP THE CAR BY STEPPING ON THE BRAKE AND MOVING GEAR SHIFTER TO NEUTRAL PREVENTING CAR FROM HITTING FENCE.THIS VEHICLE HAD THE ECM REPLACED FOR A PREVIOUS RECALL ON 6-18-11 ON THE 1ZZ-FE ENGINE 4CYL 1.8L
YOUR SITE DOES NOT SEEM TO BE WORKING PROPERLY. I ENTERED MY VIN IN THE APPROPRIATE PLACE AND CLICKED START, IT DID NOTHING. I WISH TO CHECK IF MY VEHICLE HAS AN OPEN RECALL, SPECIFICALLY, FOR TAKATA AIR BAG RECALL.
Official recalls
619V741000 · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
Oct 17, 2019
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence & remedy
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.
Additional source detail variants (2)
Air Bags:frontal:passenger Side:inflator Module
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.
Air Bags:frontal:driver Side:inflator Module
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2010-2016 4Runner, 2003-2006 Tundra, 2003-2013 Corolla, 2009-2010 Corolla Matrix, 2004-2005 RAV4, 2002-2007 Sequoia, 2011-2013 Sienna, 2008-2012 Scion xB, 2008-2009 Lexus IS-F, 2007-2012 Yaris and Lexus ES350, 2010-2017 Lexus GX460, 2002-2010 Lexus SC430, 2006-2012 Lexus IS250 and IS350 and 2010-2015 Lexus IS250C and IS350C vehicles. These vehicles had their driver or passenger frontal air bag inflators previously replaced under a prior recall using inflators of the same design. The inflators may explode due to propellant degradation occurring after long-term exposure to high absolute humidity, temperature and temperature cycling.
Consequence: An inflator explosion may result in sharp metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: Toyota will notify owners. Depending on the vehicle model, dealers will replace the front driver inflator, front passenger airbag inflator, the airbag assembly, or the front passenger airbag sub-assembly and inflator. The recall began November 20, 2019. Owners may contact Toyota customer service at 1-888-270-9371 or Lexus customer service at 1-800-255-3987. Toyota's numbers for this recall are J0A, J0B, and J0C. Lexus' numbers for this recall are JLI, JLJ, and JLK.
19V627000 · Air Bags:frontal:passenger Side:inflator Module
Aug 28, 2019
Toyota Motor Engineering & Manufacturing (Toyota) is recalling certain 2003-2008 Corolla, 2005-2008 Corolla Matrix, and Pontiac Vibe vehicles equipped with a front passenger air bag assembly replaced under a prior recall. The air bag may not unfold as designed during inflation under high temperature conditions, possibly resulting in the air bag not inflating properly.
Consequence & remedy
Consequence: An improperly inflated air bag increases the risk of injury during a crash.
Remedy: Toyota will notify their owners. Pontiac Vibe owners will be notified by GM. Dealers will replace the front passenger air bag assembly or sub-assembly, free of charge. Toyota owners may contact Toyota customer service at 1-888-270-9371. Toyota's numbers for this recall are K1Q and K0Q. Pontiac owners may contact GM customer service at 1-800-762-2737. GM's number for this recall is N192273760.
15V285000 · Air Bags
May 13, 2015
Toyota Motor Engineering & Manufacturing (Toyota) notified the agency on May 13, 2015 that they are recalling certain model year 2004 Sequoia vehicles manufactured August 18, 2003, to August 19, 2004, and 2003-2004 Tundra vehicles manufactured March 18, 2003, to August 25, 2004. On June 16, 2015, Toyota expanded the recall to include an additional 1,270,468 vehicles, including model year 2002-2003 and 2005-2007 Sequoia, 2005-2006 Tundra, 2003-2007 Corolla, 2003-2007 Corolla Matrix, 2003-2007 Pontiac Vibe and 2002-2007 Lexus SC vehicles. This is to address a safety defect in the passenger side frontal air bag inflator which may produce excessive internal pressure causing the inflator to rupture upon deployment of the air bag. This recall addresses both the passenger side frontal air bags that were originally installed in the vehicles, as well as replacement air bags that may have been installed as replacement service parts. A replacement air bag may have been installed, as one example, if a vehicle had been in a crash necessitating the replacement of the passenger side frontal air bag.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: 2003-2004 Corolla and Corolla Matrix vehicles that are recalled under both 15V-043 and 15V-285 are under a Do Not Drive advisory. Owners of these vehicles are advised not to drive their vehicles until the recall remedy has been completed. Toyota will notify their owners. Pontiac Vibe owners will be notified by GM. Dealers will replace the front passenger air bag. The recall began on July 13, 2015. Toyota owners may contact Toyota customer service at 1-800-331-4331. Pontiac owners may call 1-800-762-2737. NOTE: This recall supersedes recall 14V-312 in its entirety.
15V286000 · Air Bags
May 13, 2015
Toyota Motor Engineering & Manufacturing (Toyota) notified the agency on May 13, 2015, that they are recalling 2005-2007 Lexus SC, Toyota Corolla, Corolla Matrix, Sequoia, and Pontiac Vibe, and 2005-2006 Toyota Tundra vehicles that were originally sold, or ever registered, in Florida, along the Gulf Coast, Puerto Rico, Hawaii, the U.S. Virgin Islands, Guam, Saipan and American Samoa. On June 16, 2015 Toyota expanded the recall to cover an additional 769,055 vehicles, including certain model year 2002-2004 Lexus SC, Toyota Sequoia, 2003-2004 Toyota Corolla Matrix, Toyota Corolla, Pontiac Vibe, and Toyota Tundra vehicles, as well the vehicles covered by the May 13, 2015 notification in the portions of Georgia, Alabama, Louisiana, Mississippi and Texas that were not previously included. The inflators in the front passenger air bags are susceptible to rupture in the event of a crash necessitating the deployment of the front passenger air bag.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the passenger's frontal air bag, the inflator could rupture with metal fragments striking the vehicle occupants potentially resulting in serious injury or death.
Remedy: 2003-2004 Corolla and Corolla Matrix vehicles that are recalled under both 15V-043 and 15V-286 are under a Do Not Drive advisory. Owners of these vehicles are advised not to drive their vehicles until the recall remedy has been completed. Toyota will notify their owners. Pontiac Vibe owners will be notified by GM. Dealers will replace the passenger side front air bag, free of charge. Owners may contact Toyota customer service at 1-800-331-4331. Toyota began the recall on July 13, 2015. Pontiac Vibe owners may contact GM at 1-800-762-2737. GM began the recall on June 29, 2015. NOTE: This recacll supersedes recall 14V-655 in its entirety. For vehicles located in the U.S. states not listed above, please see Toyota recall 15V-285 which covers all other U.S. states.
10V384000 · Engine And Engine Cooling
Aug 26, 2010
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2008 COROLLA AND COROLLA MATRIX VEHICLES. THE ENGINE CONTROL MODULE (ECM) FOR THE SUBJECT MODELS EQUIPPED WITH THE 1ZZ-FE ENGINE AND TWO-WHEEL DRIVE MAY HAVE BEEN IMPROPERLY MANUFACTURED. THERE IS A POSSIBILITY THAT A CRACK MAY DEVELOP AT CERTAIN SOLDER POINTS OR ON VARISTORS ON THE CIRCUIT BOARD.
Consequence & remedy
Consequence: THERE ARE A VARIETY OF WARNINGS AND CONSEQUENCES ASSOCIATED WITH THE DEFECT. THE ENGINE WARNING LAMP COULD BE ILLUMINATED, HARSH SHIFTING COULD RESULT, THE ENGINE MAY NOT START, OR THE ENGINE COULD SHUT OFF WHILE THE VEHICLE IS BEING DRIVEN. AN ENGINE SHUTOFF WHILE THE VEHICLE IS BEING DRIVEN INCREASES THE RISK OF A CRASH.
Remedy: DEALERS WILL INSPECT THE PRODUCTION NUMBER OF THE ECM AND REPLACE THE ECM IF NECESSARY. THIS SERVICE WILL BE PERFORMED FREE OF CHARGE. TOYOTA WILL MAIL AN INTERIM OWNER NOTIFICATION THE MIDDLE OF SEPTEMBER 2010 TO ADVISE OWNERS OF THIS DEFECT AND RECALL. THIS INTERIM NOTIFICATION WILL INFORM OWNERS THAT THEY WILL RECEIVE A FUTURE NOTIFICATION WHEN PARTS BECOME AVAILABLE TO HAVE THE FREE REMEDY PERFORMED ON THEIR VEHICLE. THE SAFETY RECALL BEGAN ON NOVEMBER 29, 2010. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331.
10V036000 · Equipment:other:labels
Feb 3, 2010
SOUTHEAST TOYOTA IS RECALLING CERTAIN MODEL YEAR 2005-2011 PASSENGER VEHICLES FOR FAILING TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTION AND RIMS." THESE VEHICLES WERE SOLD WITHOUT THE REQUISITE LOAD CARRYING CAPACITY MODIFICATION LABELS.
Consequence & remedy
Consequence: A DRIVER MAY OVERLOAD A VEHICLE WHICH MAY INCREASE THE RISK OF A CRASH.
Remedy: DEALERS WILL MAIL TO CONSUMERS THE CORRECTED LABEL OR THE CUSTOMER WILL HAVE THE OPTION FOR DEALERS TO INSTALL THE LABEL FREE OF CHARGE. THE SAFETY RECALL BEGAN ON MAY 27, 2010. OWNERS MAY CONTACT SOUTHEAST TOYOTA AT 1-800-301-6859.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
DP14003 · Low-speed Surging
Opened Sep 19, 2014 · Closed Apr 29, 2015
Status: closed (inferred from source dates) · Vehicle Speed Control
The Agency received a petition on September 11, 2014 requesting an investigation into, low-speed surging in the 2006-2010 Toyota Corolla [vehicles] with ETCS-i, in which the brakes fail to stop the vehicle in time to prevent a crash.NHTSA conducted a technical review of the material cited and provided by the petitioner, material Toyota submitted in response to a NHTSA formal request, interviews with complainants and manufacturer representatives, as well as the results of testing of the complaint vehicle.Taking into account the allocation of agency resources, agency priorities, and the likelihood that an additional investigation would result in a finding that a defect related to motor vehicle safety exists, NHTSA has concluded that further investigation of the issues raised by the petition is not warranted.The agency accordingly has denied the petition.The official petition denial, as published in the Federal Register, is available in the document file for this defect petition, as well as copies of reference material related to the denial.Regarding the VOQs associated with the closing of this investigation, the scope as defined by the petitioner is MY 2006 through 2010 Toyota Corollas.Of the 163 VOQs submitted by the petitioner, 149 are within that specific population (11 of the 163 were outside the model and model year scope of investigation as defined by the petitioner and 3 VOQs were submitted by owners from foreign countries) and 6 of the 163 are duplicate submissions.Therefore, there are 143 unique vehicles vins are within the specific population.Of the 143 only 105 fit the alleged defect category as defined by the petitioner.The single complaint and crash noted in the Failure Report above is the petitioner's VOQ.The 143 VOQs are: 10165337, 10166526, 10209540, 10216514, 10256808 (duplicate with 10266580 and 10335955), 10272505, 10293497, 10293688, 10294727, 10297407, 10298012, 10302217, 10302877, 10303106, 10303469, 10303730, 10304192, 10305748, 10305845, 10306012, 10306480, 10307953, 10310973, 10311137, 10311176, 10311185, 10311756, 10312246, 10312272 (duplicate with 10343088), 10312771, 10313972, 10314880, 10315240, 10315442, 10315836, 10315927, 10316192, 10316627, 10316643, 10316800, 10316952, 10317128, 10317598, 10317725, 10317804, 10317894, 10317972, 10317978, 10318562, 10319589, 10320693, 10320720, 10322163, 10322213, 10322333, 10322415, 10324355, 10325755, 10326481, 10327623, 10328492, 10328519, 10329537, 10330026 (duplicate with 10356866), 10330952, 10332679, 10334005 (duplicate with 10340570 and 10547602), 10334028, 10334628, 10334936, 10336649, 10339772, 10339969, 10341515, 10342670, 10342932, 10343174, 10344874, 10345714, 10348120, 10350342, 10351112, 10352668, 10352691, 10353587, 10358767, 10359645, 10360875, 10360905, 10361254, 10363529, 10363685, 10363866, 10364127, 10366100, 10366413, 10369073, 10369494, 10371991, 10376535, 10376721, 10377193, 10379320, 10380210, 10381365, 10381849, 10382018, 10392618, 10396747, 10402827, 10412382, 10433860, 10437011, 10437801, 10450183, 10461118, 10479582, 10482133, 10489344, 10494568, 10496026, 10499932, 10520195, 10521013, 10523677, 10534094, 10537426, 10543949, 10549101, 10551478, 10552563, 10558153, 10562577, 10564980, 10566370, 10572873, 10578871, 10579722, 10587140, 10597296, 10621449, and 10637908 (which is the petitioner's VOQ and not one of the 163 submitted with the petition).The three VOQs that were submitted from foreign countries: 10303105, 10303749, and 10308974. The eleven VOQs that are out of the specified population by model or model year: 10447756, 10453401, 10490200, 10507434, 10521377, 10563214, 10563585, 10575230, 10583796, 10584534,
EA10006 · Engine Stall
Opened Aug 18, 2010 · Closed Sep 16, 2010
Status: closed (inferred from source dates) · Engine And Engine Cooling
On August 26, 2010, Toyota submitted a Defect Information Report to the National Highway Traffic Safety Administration (NHTSA) regarding problems with Engine Control Modules that could result in engine stall while driving in certain model year (MY) 2005 through 2008 Toyota Corolla, Corolla Matrix and Pontiac Vibe vehicles equipped with the 1ZZ-FE engine and two-wheel drive and manufactured between April 19, 2004 and January 2, 2008.Toyota's report indicated that cracks may develop at certain solder point or on varistors on the ECMs.According to Toyota, such cracks generally resulted in engine warning lamp illumination, harsh shifting or engine no-start.In some cases, if the cracking occurs on particular solder points or varistors, the engine could stop while the vehicle is being driven.Toyota will notify owners of subject vehicles that they should return their vehicles to a Toyota or Pontiac dealer.Dealers will be instructed to inspect the production number of the ECM for each vehicle and replace the ECM if necessary.On November 30, 2009, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE09-054) to investigate alleged engine stall while driving in model year (MY) 2006 Toyota Corolla and Corolla Matrix vehicles.In its response to ODI's information request, submitted on March 2, 2010, Toyota indicated that it had identified two possible conditions with ECMs used in MY 2005 through 2007 Toyota Corolla and Matrix vehicles:1) cracks forming between the IC and the board caused by an improperly cured conformal coating applied to the circuit boards after the soldering process is completed; and 2) cracks occurring in a variable resistor (varistor) due to overheating.During the manufacturing process a glass coating is created on the surface of the varistor.Between March and August 2010, Toyota began collecting ECMs from the field to further investigate failure modes that may result in engine stall.Toyota also conducted durability testing on ECMs collected from in-use vehicles to assess whether the problems may be a continuing trend. In addition, they conducted durability testing in order to assess whether this problem was a continuing trend.Toyota found that 4 of 32 collected ECMs malfunctioned after thermal shock testing.Toyota also confirmed that cracking could develop at solder points on the ECM circuit board that could lead to engine stall while driving and that this trend was likely to continue.The manufacturer failure data in this resume is limited to MY 2005 through 2007 Toyota Corolla and Corolla Matrix vehicles.Based on Toyota's recall, this Engineering analysis has been closed.
Additional source detail variants (2)
Engine And Engine Cooling
On August 26, 2010, Toyota submitted a Defect Information Report to the National Highway Traffic Safety Administration (NHTSA) regarding problems with Engine Control Modules that could result in engine stall while driving in certain model year (MY) 2005 through 2008 Toyota Corolla, Corolla Matrix and Pontiac Vibe vehicles equipped with the 1ZZ-FE engine and two-wheel drive and manufactured between April 19, 2004 and January 2, 2008.Toyota's report indicated that cracks may develop at certain solder point or on varistors on the ECMs.According to Toyota, such cracks generally resulted in engine warning lamp illumination, harsh shifting or engine no-start.In some cases, if the cracking occurs on particular solder points or varistors, the engine could stop while the vehicle is being driven.Toyota will notify owners of subject vehicles that they should return their vehicles to a Toyota or Pontiac dealer.Dealers will be instructed to inspect the production number of the ECM for each vehicle and replace the ECM if necessary.On November 30, 2009, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE09-054) to investigate alleged engine stall while driving in model year (MY) 2006 Toyota Corolla and Corolla Matrix vehicles.In its response to ODI's information request, submitted on March 2, 2010, Toyota indicated that it had identified two possible conditions with ECMs used in MY 2005 through 2007 Toyota Corolla and Matrix vehicles:1) cracks forming between the IC and the board caused by an improperly cured conformal coating applied to the circuit boards after the soldering process is completed; and 2) cracks occurring in a variable resistor (varistor) due to overheating.During the manufacturing process a glass coating is created on the surface of the varistor.Between March and August 2010, Toyota began collecting ECMs from the field to further investigate failure modes that may result in engine stall.Toyota also conducted durability testing on ECMs collected from in-use vehicles to assess whether the problems may be a continuing trend. In addition, they conducted durability testing in order to assess whether this problem was a continuing trend.Toyota found that 4 of 32 collected ECMs malfunctioned after thermal shock testing.Toyota also confirmed that cracking could develop at solder points on the ECM circuit board that could lead to engine stall while driving and that this trend was likely to continue.The manufacturer failure data in this resume is limited to MY 2005 through 2007 Toyota Corolla and Corolla Matrix vehicles.Based on Toyota's recall, this Engineering analysis has been closed.
Engine And Engine Cooling
On August 26, 2010, Toyota submitted a Defect Information Report to the National Highway Traffic Safety Administration (NHTSA) regarding problems with Engine Control Modules that could result in engine stall while driving in certain model year (MY) 2005 through 2008 Toyota Corolla, Corolla Matrix and Pontiac Vibe vehicles equipped with the 1ZZ-FE engine and two-wheel drive and manufactured between April 19, 2004 and January 2, 2008.Toyota's report indicated that cracks may develop at certain solder point or on varistors on the ECMs.According to Toyota, such cracks generally resulted in engine warning lamp illumination, harsh shifting or engine no-start.In some cases, if the cracking occurs on particular solder points or varistors, the engine could stop while the vehicle is being driven.Toyota will notify owners of subject vehicles that they should return their vehicles to a Toyota or Pontiac dealer.Dealers will be instructed to inspect the production number of the ECM for each vehicle and replace the ECM if necessary.On November 30, 2009, the Office of Defects Investigation (ODI) opened a Preliminary Evaluation (PE09-054) to investigate alleged engine stall while driving in model year (MY) 2006 Toyota Corolla and Corolla Matrix vehicles.In its response to ODI's information request, submitted on March 2, 2010, Toyota indicated that it had identified two possible conditions with ECMs used in MY 2005 through 2007 Toyota Corolla and Matrix vehicles:1) cracks forming between the IC and the board caused by an improperly cured conformal coating applied to the circuit boards after the soldering process is completed; and 2) cracks occurring in a variable resistor (varistor) due to overheating.During the manufacturing process a glass coating is created on the surface of the varistor.Between March and August 2010, Toyota began collecting ECMs from the field to further investigate failure modes that may result in engine stall.Toyota also conducted durability testing on ECMs collected from in-use vehicles to assess whether the problems may be a continuing trend. In addition, they conducted durability testing in order to assess whether this problem was a continuing trend.Toyota found that 4 of 32 collected ECMs malfunctioned after thermal shock testing.Toyota also confirmed that cracking could develop at solder points on the ECM circuit board that could lead to engine stall while driving and that this trend was likely to continue.The manufacturer failure data in this resume is limited to MY 2005 through 2007 Toyota Corolla and Corolla Matrix vehicles.Based on Toyota's recall, this Engineering analysis has been closed.
Illustration