IllustrationI WAS DRIVING FROM DELAWARE TO PHILADELPHIA ON A RAINY DAY AND SUDDENLY THE LIGHT OF THE BREAK, ABS AND STABILITY LIGHT COME UP. ALSO THERE IS A MESSAGE TELLING TO CHECK VSC SYSTEM. I PULLED OVER AND STARTED THE CAR AGAIN AND NOTHING HAPPENED . I'M SCARE TO DRIVE THE CAR ON HIS CONDITION SINCE I'M PREGNANT.
2007 Toyota Camry Hybrid
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all Camry Hybrid years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
350–25K
5325–50K
8650–75K
11975–100K
169100–150K
81150K+
543 reports with mileage · 59 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Service Brakes. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Vehicle Speed Control. Review the 160 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electronic Stability Control (esc). Review the 115 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
31 crash reports7 fire reports14 injury reports
What owners actually said
602 reportsTAKATA MY 2007 TOYOTA HYBRID HAS BEEN BEHAVING BADLY, WITH JUST 190K MILES.MY TRACTION BATTERY MONITOR WOULD SHOW 7 BARS FALLING TO 1 BAR INSTANTLY. INSTANTLY, AS I WOULD BE LOOKING AT IT AND IT JUST DROPPED THAT FAST. IT WOULD GET PARKED WITH A FULL CHARGE INDICATED AND THEN THE NEXT MORNING ONE BAR. SOMETIMES IT GOES INTO E M…
Read full complaint
TAKATA MY 2007 TOYOTA HYBRID HAS BEEN BEHAVING BADLY, WITH JUST 190K MILES.MY TRACTION BATTERY MONITOR WOULD SHOW 7 BARS FALLING TO 1 BAR INSTANTLY. INSTANTLY, AS I WOULD BE LOOKING AT IT AND IT JUST DROPPED THAT FAST. IT WOULD GET PARKED WITH A FULL CHARGE INDICATED AND THEN THE NEXT MORNING ONE BAR. SOMETIMES IT GOES INTO E MODE AND SHUTS OFF WHILE DRIVING ON HIGHWAY IVE BEEN CLOSE TO CRASH WITH OTHER VEHICLES. THE ECM THROWS A WARNING, "CHECK HYBRID SYSTEM". I BORROWED AN ACTRON SCANNER THAT HAD THE CAPABILITY OF BASIC HYBRID CODES AND ONE CODE WAS PRESENT "P0A80". ALSO, CHECK VSC WOULD SHOW ALL THE TIMES. SOMEWHERE I READ THIS IS NORMAL WITH P0A80 AS THE ECM SHUTS DOWN THE VSC TO CONSERVE POWER..
TL* THE CONTACT OWNS A 2007 TOYOTA CAMRY HYBRID. WHEN THE CONTACT APPLIED THE BRAKES, THE ABS AND VSC WARNING INDICATORS ILLUMINATED. THE CONTACT HAD TO APPLY FORCE TO THE BRAKE PEDAL TO STOP THE VEHICLE. A MECHANIC WAS UNABLE TO REPLICATE AND DIAGNOSE THE FAILURE DUE TO THE DTC NOT BEING ILLUMINATED WHEN IT WAS INSPECTED. THE V…
Read full complaint
TL* THE CONTACT OWNS A 2007 TOYOTA CAMRY HYBRID. WHEN THE CONTACT APPLIED THE BRAKES, THE ABS AND VSC WARNING INDICATORS ILLUMINATED. THE CONTACT HAD TO APPLY FORCE TO THE BRAKE PEDAL TO STOP THE VEHICLE. A MECHANIC WAS UNABLE TO REPLICATE AND DIAGNOSE THE FAILURE DUE TO THE DTC NOT BEING ILLUMINATED WHEN IT WAS INSPECTED. THE VEHICLE WAS TAKEN TO A DEALER (NASHVILLE TOYOTA NORTH, 2400 GALLATIN PIKE N, MADISON, TN 37115, (615) 868-7990) WHERE IT WAS DIAGNOSED THAT THE BRAKE ACTUATOR NEEDED TO BE REPLACED WITH A WARRANTY REPAIR. THE DEALER AND THE MANUFACTURER INDICATED THAT THE WARRANTY ENHANCEMENT WAS NO LONGER AVAILABLE AND THE VEHICLE SHOULD HAVE BEEN REPAIRED BEFORE THE CAMPAIGN ENDED ON AUGUST 31, 2017. THE CONTACT RECEIVED NO DOCUMENTATION FROM THE MANUFACTURER PERTAINING TO THE WARRANTY ENHANCEMENT PROGRAM. THE MANUFACTURER STATED THAT THEY WERE AWARE THAT THE FAILURE WAS A KNOWN ISSUE AND THERE WAS A TECHNICAL SERVICE BULLETIN ON THE BRAKE SYSTEM. THE CONTACT REFUSED TO REPAIR THE VEHICLE AND INDICATED THAT THE CONTACT NEEDED TO REPLACE THE PART. THE APPROXIMATE FAILURE MILEAGE WAS 76,000.
BRAKE ACTUATOR FAILED, TRIGGERING WARNING LIGHTS AND MAKING IT HARD TO PUSH ON THE PEDAL TO STOP THE CAR WHILE IN MOTION. ABS FUNCTION WON'T ACTIVATE. THE ISSUE STARTED IN MAY 2017 AND WAS TAKEN TO A TOYOTA DEALER IN LUFKIN, TEXAS FOR DIAGNOSIS. THE TECHNICIANS "COULDN'T" DETERMINE THE PROBLEM AND RELEASED THE VEHICLE. THIS SA…
Read full complaint
BRAKE ACTUATOR FAILED, TRIGGERING WARNING LIGHTS AND MAKING IT HARD TO PUSH ON THE PEDAL TO STOP THE CAR WHILE IN MOTION. ABS FUNCTION WON'T ACTIVATE. THE ISSUE STARTED IN MAY 2017 AND WAS TAKEN TO A TOYOTA DEALER IN LUFKIN, TEXAS FOR DIAGNOSIS. THE TECHNICIANS "COULDN'T" DETERMINE THE PROBLEM AND RELEASED THE VEHICLE. THIS SAME STEP HAPPENED MULTIPLE TIMES OVER THE ENSUING MONTHS, ONLY TO BE FINALLY DIAGNOSED ON DEC 13, 2017. I RESEARCHED THE ISSUE ONLINE AND FOUND THAT THE ACTUATOR PROBLEM IS COVERED BY A 'WARRANTY EXTENSION,' WHICH STRETCHES OUT THE WARRANTY PERIOD BEYOND THE STANDARD THREE YEARS OR 36 MONTHS TO, ULTIMATELY, 10 YEARS OR 150,000 MILES, WHICHEVER COMES FIRST. I THOUGHT THAT WAS GOOD NEWS, BUT AFTER SPEAKING WITH TOYOTA CORPORATE REP, THE WARRANTY WAS DENIED DUE TO THE VEHICLE BEING OUT OF THE COVERAGE PERIOD SINCE JUNE. I EXPLAINED THAT THERE WERE ATTEMPTS TO HAVE THE ISSUE DIAGNOSED PRIOR TO THE EXPIRATION, BUT THE REP STATED THAT SINCE THE ACTUAL DETERMINATION HAPPENED OUTSIDE OF THE PERIOD, COVERAGE COULD NOT BE EXTENDED. SINCE THIS IS A KNOWN ISSUE, THEIR TECHS SHOULD HAVE RECOGNIZED THE PROBLEM IMMEDIATELY AND REPAIRED THE VEHICLE, WHICH WOULD HAVE BEEN COVERED BY THE EXTENDED WARRANTY. FURTHERMORE, IT'S A SAFETY ISSUE AND AN ACTUAL RECALL SHOULD BE THE REMEDY INSTEAD OF WORKING AROUND IT WITH A "SERVICE CAMPAIGN." I AM ASKING FOR ASSISTANCE TO HAVE TOYOTA COVER THIS REPAIR DUE THEIR FAILURE TO EDUCATE THEIR SERVICE TECHS OR A POTENTIAL DELIBERATE ATTEMPT TO MOVE THE DIAGNOSE OUTSIDE OF THE WARRANTY COVERAGE PERIOD.
THE VSC WARNING SYSTEM CAME ON INCLUDING SEVERAL WARNING LIGHTS. THE ABS ACTUATOR FAILED. I AM TOLD THIS IS A KNOWN ISSUE BUT IS OUT OF WARRANTY AND THE REPAIR IS $1500-$2000. THIS SHOULD HAVE BEEN RECALLED.
TODAY, DECEMBER 11, 2017, WHILE DRIVING MY 2007 TOYOTA CAMRY HYBRID VEHICLE ON A CITY STREET IN TRAFFIC, THE 'CHECK VSC SYSTEM' WARNING CAME ON. ALL DASH LIGHTS INCLUDING 'BRAKES' CAME ON AND VEHICLE BECAME DIFFICULT TO STOP. THERE WAS NO POWER ASSISTED BRAKING. BRAKE PEDAL WAS HARD TO ENGAGE AND WHEN VEHICLE CAME TO A STOP, THE…
Read full complaint
TODAY, DECEMBER 11, 2017, WHILE DRIVING MY 2007 TOYOTA CAMRY HYBRID VEHICLE ON A CITY STREET IN TRAFFIC, THE 'CHECK VSC SYSTEM' WARNING CAME ON. ALL DASH LIGHTS INCLUDING 'BRAKES' CAME ON AND VEHICLE BECAME DIFFICULT TO STOP. THERE WAS NO POWER ASSISTED BRAKING. BRAKE PEDAL WAS HARD TO ENGAGE AND WHEN VEHICLE CAME TO A STOP, THERE WAS A SINGLE "KNOCK OR BANG" SOUND. THIS WARNING HAD COME ON PREVIOUSLY WITHOUT BRAKING ISSUE UNTIL LAST WEEK WHEN MY WIFE TOLD ME SHE HAD A SIMILAR PROBLEM DRIVING HOME FROM WORK. I CLEANED AND SUBSEQUENTLY REPLACED THE GAS CAP AS PER A YOU TUBE DESCRIBED REPAIR OF THE CHECK VSC WARNING. I THEN DROVE THE CAR INTERMITTENTLY SINCE THAT TIME WITHOUT INCIDENT UNTIL TODAY. MY WIFE EXPERIENCED THE PROBLEM 12/7/2017.
ON MY 2007 CAMRY HYBRID, AS I WAS BACKING UP, THE BRAKES WENT SOFT TO THE FLOOR, AND THEN ALL OF A SUDDEN ENGAGED. IT BRAKED SO HARD, IT FELT LIKE A HIT SOMETHING. A FEW DAYS LATER, THE BRAKE LIGHT, TRACTION CONTROL AND ABS LIGHTS TURNED ON, AND CHECK VSC SYSTEM DISPLAYED.
THE HYBRID BATTERIE IS NOT RESPONDING WITH THE CARS VELOCITY. IT TURNS OFF IN THE MIďDLE OF MY TRIP. I WORRY FOR MY SAFTEY AND MY FAMILIES BCUS I FEAR TO HAVE AN ACCIDENT DUE TO THAT REASON
DRIVING NORMAL AND BRAKE LIGHT INDICATOR LIGHTS UP WITH VCS MESSAGE AND POWER BRAKES FAIL. THIS IS AN INTERMITTENT PROBLEM ON HIGHWAY OR LOCAL ROADS.
I NEEDED TO SLOW FOR TRAFFIC CONGESTION. I APPLIED THE BRAKES, BUT THEY DIDN'T SEEM TO WORK. SEVERAL LIGHTS ON THE DASH CAME ON INCLUDING THE CHECK HYBRID ENGINE, THE CHECK VSC SYSTEM, AND THE ABS LIGHTS. THE POWER BRAKES WERE OFF AND IT BECAME DIFFICULT TO STOP. THEN THE VEHICLE'S ENGINE STOPPED COMPLETELY REQUIRING ME TO MANEU…
Read full complaint
I NEEDED TO SLOW FOR TRAFFIC CONGESTION. I APPLIED THE BRAKES, BUT THEY DIDN'T SEEM TO WORK. SEVERAL LIGHTS ON THE DASH CAME ON INCLUDING THE CHECK HYBRID ENGINE, THE CHECK VSC SYSTEM, AND THE ABS LIGHTS. THE POWER BRAKES WERE OFF AND IT BECAME DIFFICULT TO STOP. THEN THE VEHICLE'S ENGINE STOPPED COMPLETELY REQUIRING ME TO MANEUVER OUT OF HEAVY TRAFFIC TO THE SHOULDER OF THE ROAD. I TURNED THE CAR OFF AND WAITED 10 MINUTES. I WAS ABLE TO DRIVE THE CAR TO A TOYOTA DEALER WHO SAID SOMETIMES THIS HAPPENS IF GAS CAP IS LOOSE. I WAS TOLD I COULD LEAVE AND THEY WOULD TROUBLESHOOT FOR A COUPLE OF HOURS AND A COUPLE HUNDRED DOLLARS. I LEFT AND CONDUCTED MY OWN TROUBLESHOOTING ON GOOGLE AND SOUNDS LIKE A BRAKE ACTUATOR PROBLEM DUE TO SIMILAR ISSUES WITH OTHER OWNERS. TOYOTA HAS A KNOW ISSUE WITH THIS VEHICLE AND NEEDS TO MAKE AMENDS. PLEASE ADVISE.
Official recalls
315V689000 · Visibility:power Window Devices And Controls
Oct 22, 2015
Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.
Consequence & remedy
Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.
Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.
12V491000 · Visibility:power Window Devices And Controls
Oct 10, 2012
Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.
Consequence & remedy
Consequence: If the switch overheats, it may melt, possibly resulting in a fire.
Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.
09V388000 · Vehicle Speed Control:accelerator Pedal
Oct 5, 2009
TOYOTA IS RECALLING CERTAIN MODEL YEAR 2004-2010 PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT.
Consequence & remedy
Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.
Remedy: TOYOTA FILED AN AMENDED DEFECT REPORT ON NOVEMBER 25, 2009, STATING THAT DEALERS WILL MODIFY THE ACCELERATOR PEDAL AND, ON CERTAIN VEHICLES, ALTER THE SHAPE OF THE FLOOR SURFACE UNDER THE PEDAL. THESE CHANGES ADDRESS THE RISK OF PEDAL ENTRAPMENT DUE TO INTERFERENCE WITH THE FLOOR MAT. REDESIGNED ACCELERATOR PEDALS WILL BECOME AVAILABLE BEGINNING IN APRIL 2010 AND DEALERS WILL REPLACE ANY MODIFIED PEDAL WITH THE NEW PEDAL IF DESIRED. ALSO, DEALERS WILL REPLACE ANY GENUINE TOYOTA OR LEXUS ALL-WEATHER FLOOR MATS WITH REDESIGNED ALL-WEATHER MATS, OR REPURCHASE THE PREVIOUS MATS FROM OWNERS WHO DO NOT WANT THE NEW ONES. ADDITIONALLY, SOFTWARE MODIFICATIONS WILL BE INSTALLED ON CAMRY, AVALON AND LEXUS ES 350, IS 350 AND IS 250 MODELS THAT WILL ENSURE THAT THE BRAKE OVERRIDES THE ACCELERATOR IN THE EVENT BOTH BRAKE AND ACCELERATOR PEDALS ARE APPLIED. TOYOTA WILL BEGIN MAILING LETTERS TO OWNERS ON DECEMBER 31, 2009. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331, LEXUS AT 1-800-255-3987.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4DP22005 · Pedestrian Alert Sounds
Opened Jan 27, 2023 · Closed Aug 7, 2023
Status: closed (inferred from source dates) · Electrical System:propulsion System
NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.
PE14001 · Brake Actuator Malfunction
Opened Jan 23, 2014 · Closed Aug 22, 2014
Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Air:supply:reservoir/tank; Service Brakes, Electric; Service Brakes, Hydraulic:power Assist
On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.
Additional source detail variants (4)
Service Brakes, Air:supply:reservoir/tank
On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.
Service Brakes, Electric
On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.
Service Brakes, Hydraulic:power Assist
On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.
Service Brakes
On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.
EA12006 · Power Window Master Switch Fire
Opened Jun 14, 2012 · Closed Feb 12, 2013
Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Additional source detail variants (3)
Electrical System
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Structure:body
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
Unknown Or Other
On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.
PE12002 · Power Window Master Switch Fire
Opened Feb 6, 2012 · Closed Jun 14, 2012
Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Additional source detail variants (3)
Electrical System
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Structure:body
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.
Unknown Or Other
ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.