← New search

2007 Toyota Camry Hybrid

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

543 reports with mileage · 59 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Service Brakes. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Vehicle Speed Control. Review the 160 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electronic Stability Control (esc). Review the 115 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

31 crash reports7 fire reports14 injury reports

Structure complaints

30 reports
Clear category filter
79,119 miles · May 1, 2014
StructureVehicle Speed ControlCrash

CHECK VSC SYSTEM WARNING, ABS, MULTI LIGHTS ON. WHEN BUZZ SOUND CONTINUALLY ARMS, IT IS SO HARD TO APPLY BRAKE PEDAL TO STOP COMPLETELY. THE BRAKES ARE OUT OF CONTROL. IT IS A DEFECT FROM MANUFACTURE, NOT A USING CONSUMER. THE BRAKE SYSTEM IS SO IMPORTANT WHEN MOVING. PLEASE RECALL TO FIX BEFORE CAUSING DEATHLY ACCIDENT. *TR

NHTSA ODI #10586069

49,000 miles · Apr 10, 2014
Air BagsElectrical SystemStructureCrashInjury

AT A PARKING SPOT, FULL STOP, SUDDENLY THE VEHICLE SURGED AND HIT A CEMENT POST. AIR BAGS DID NOT DEPLOY. DAMAGE TO VEHICLE WAS OVER $7500 LEFT KNEE/SHIN HIT DASH DUE TO KNEE AIR BAG NOT DEPLOYING. INJURY WAS NOT REPORTED AS IT DID NOT SHOW UP UNTIL LATER. *TR

NHTSA ODI #10578831

11,126 miles · Mar 30, 2014
Service Brakes, HydraulicStructureCrash

STOP AND GO TRAFFIC ON THE 101 EB GOING 10 MPH AT 8:50 AM. TRIED TO STOP AND BRAKES FAILED. I TRIED AGAIN TO STOP AND BRAKES FAILED. RAN INTO THE LEFT REAR OF CAR IN FRONT OF ME. WE WERE ALL MOVING SLOWLY SO DAMAGE TO HIS CAR WAS LESS THAN MINE. BUT THE FEELING OF NOT BEING ABLE TO STOP THE CAR WAS TRAUMATIC! CAR IS NOT DU…

Read full complaint

STOP AND GO TRAFFIC ON THE 101 EB GOING 10 MPH AT 8:50 AM. TRIED TO STOP AND BRAKES FAILED. I TRIED AGAIN TO STOP AND BRAKES FAILED. RAN INTO THE LEFT REAR OF CAR IN FRONT OF ME. WE WERE ALL MOVING SLOWLY SO DAMAGE TO HIS CAR WAS LESS THAN MINE. BUT THE FEELING OF NOT BEING ABLE TO STOP THE CAR WAS TRAUMATIC! CAR IS NOT DUE FOR SERVICE FOR ANOTHER 1000 MILES. IT IS SERVICED REGULARLY BY DEALER. *TR

NHTSA ODI #10575739

140,000 miles · Jan 31, 2014
StructureVisibility

MY DRAIN TUBE FOR MY SUNROOF HAS BECOME DISCONNECTED TWICE NOW. I PAID SEVERAL HUNDRED DOLLARS TO HAVE IT REPAIRED AT THE TOYOTA DEALERSHIP IN 2010 AND IT HAS HAPPENED AGAIN IN 2014. *TR

NHTSA ODI #10562351

35,753 miles · Nov 14, 2013
Structure

THE DASHBOARD OF MY 2007 CAMRY IS MELTING. IT IS VERY STICKY AND PARTS ARE ALSO VERY SHINY CAUSING A GLARE. TOYOTA SAYS THEY HAVE NO CURRENT PROGRAM TO RESOLVE THIS SO I THEY EXPECT ME TO PAY 2200 TO REPLACE THE DASHBOARD. I HAVE CHECKED THE INTERNET AND FOUND A NUMBER OF OTHER PEOPLE WITH THE SAME PROBLEM. *TR

NHTSA ODI #10552254

108,000 miles · Aug 12, 2013
Structure

MY DASHBOARD IS VERY STICKY, SHINY AND MELTING. IT IS SO SHINY THAT IT MAKES A GLARE UPON MY WINDSHIELD, IMPAIRING THE VISIBILITY. I HAVE ONLY USED A DAMP CLOTH TO CLEAN THE DASHBOARD. I GOOGLED THIS CONDITION AND FOUND MANY OTHER CAMRY OWNERS OF 07, 08, AND 09 YEAR CARS FROM HAWAII, US MAINLAND, AND AUSTRALIA THAT HAVE PROBLEMS…

Read full complaint

MY DASHBOARD IS VERY STICKY, SHINY AND MELTING. IT IS SO SHINY THAT IT MAKES A GLARE UPON MY WINDSHIELD, IMPAIRING THE VISIBILITY. I HAVE ONLY USED A DAMP CLOTH TO CLEAN THE DASHBOARD. I GOOGLED THIS CONDITION AND FOUND MANY OTHER CAMRY OWNERS OF 07, 08, AND 09 YEAR CARS FROM HAWAII, US MAINLAND, AND AUSTRALIA THAT HAVE PROBLEMS WITH THEIR DASHBOARD MELTING. IT IS SOFT AND STICKY AT NIGHTTIME AND IN THE SHADE ALSO. THIS IS CLEARLY DEFECTIVE MATERIAL USED FOR THE DASHBOARD. I AM CONCERNED ABUT FUMES FROM THE MELTING MATERIAL WHEN ENTERING THE CAR WHEN IT IS HOT. I BELIEVE TOYOTA SHOULD REPLACE THIS AS IT IS NOT COVERED UNDER WARRANTY, EVEN IF IT WAS STILL UNDER WARRANTY. *TR

NHTSA ODI #10534836

78,000 miles · Jun 21, 2013
Structure

I RECENTLY PURCHASED A '07 TOYOTA CAMRY FROM MY MOTHER. IT STILL HAS WARRANTY. I HAVEN'T TAKEN IT IN YET, BUT THE DASHBOARD IS MELTING. I WAS IN AN UNDERGROUND PARKING DECK AWAY FROM HOME. I WAS PUTTING AN ADDRESS INTO MY GPS WHILE RESTING ONE OF MY FINGERS ON THE DASHBOARD WHILE I TYPED. I WENT TO REMOVE MY FINGER AND REAL…

Read full complaint

I RECENTLY PURCHASED A '07 TOYOTA CAMRY FROM MY MOTHER. IT STILL HAS WARRANTY. I HAVEN'T TAKEN IT IN YET, BUT THE DASHBOARD IS MELTING. I WAS IN AN UNDERGROUND PARKING DECK AWAY FROM HOME. I WAS PUTTING AN ADDRESS INTO MY GPS WHILE RESTING ONE OF MY FINGERS ON THE DASHBOARD WHILE I TYPED. I WENT TO REMOVE MY FINGER AND REALIZED THAT MY FINGERNAIL WAS STUCK IN THE DASHBOARD. A COUPLE OF DAYS LATER I WAS LOADING SOME THIN BAMBOO STALKS (LESS THAN 1/4 INCH THICK) AND THEY GOUGED HOLES MY DASHBOARD. I AM VERY SAD. I WANTED TO SEE IF ANYONE ELSE HAD THIS PROBLEM.....APPARENTLY SO...AND SOME SOUND MUCH WORSE THAN MINE. I HOPE THEY WILL FIX THIS. *TR

NHTSA ODI #10521153

45,000 miles · Jun 14, 2013
Structure

CAR PARKED IN SUN, DASHBOARD MATERIAL GETTING VERY STICKY/GOOEY. IF TOUCHED, IT GETS DAMAGED. IT SHOWS A VERY SHINY APPEARANCE WHEN HOT ( LIKE IF YOU USED A TIRE SHINE ON IT), ON SUNNY DAYS IT CREATES A LOT OF GLARE ON THE WINDSHIELD AFFECTING VISIBILITY. DASH CANNOT BE WIPED WITH ANYTHING BECAUSE IT IS VERY STICKY AND GOOEY. I …

Read full complaint

CAR PARKED IN SUN, DASHBOARD MATERIAL GETTING VERY STICKY/GOOEY. IF TOUCHED, IT GETS DAMAGED. IT SHOWS A VERY SHINY APPEARANCE WHEN HOT ( LIKE IF YOU USED A TIRE SHINE ON IT), ON SUNNY DAYS IT CREATES A LOT OF GLARE ON THE WINDSHIELD AFFECTING VISIBILITY. DASH CANNOT BE WIPED WITH ANYTHING BECAUSE IT IS VERY STICKY AND GOOEY. I CAN ACCEPT DASHBOARD DAMAGE ON A 10YEAR PLUS CAR, BUT NOT ON A 6 YEAR OLD CAR.THIS IS CLEARLY A MATERIAL DEFECT AND IT PROMPTS FOR A RECALL. SPECIALLY BECAUSE OF THE GLARE ON THE FRONT WINDSHIELD THE DASH CREATES WHEN IT IS VERY HOT. *TR

NHTSA ODI #10519839

Mileage unknown · May 8, 2008
Structure

VERY POOR PAINT ON MY CAMRY 2007. *TR

NHTSA ODI #10227044

1,500 miles · Jul 18, 2007
Structure

TOYOTA CAMRY HYBRID 2007 BLACK PAINT IS DEFECTIVE DESIGN TECHNOLOGY. TOYOTA CHANGED TO A WATER BASED PAINT TWO YEARS AGO, AND THE PRODUCT IS A MANUFACTURER'S DEFECTIVE DESIGN AND PROCESS. TOYOTA IS HIDING THIS FACT FROM ITS CUSTOMER BASE. CALL TOYOTA CORPORATE GET CASE NUMBER AND COMPLAINT LIKE CRAZY. FILE A COMPLAINT WITH NHT…

Read full complaint

TOYOTA CAMRY HYBRID 2007 BLACK PAINT IS DEFECTIVE DESIGN TECHNOLOGY. TOYOTA CHANGED TO A WATER BASED PAINT TWO YEARS AGO, AND THE PRODUCT IS A MANUFACTURER'S DEFECTIVE DESIGN AND PROCESS. TOYOTA IS HIDING THIS FACT FROM ITS CUSTOMER BASE. CALL TOYOTA CORPORATE GET CASE NUMBER AND COMPLAINT LIKE CRAZY. FILE A COMPLAINT WITH NHTSA. BE HONEST, YOU PAID A LOT OF MONEY FOR A DEFECTIVE PAINT JOB AND THEY KNEW IT. NEVER BUY A TOYOTA AGAIN! *AK

NHTSA ODI #10196702

Official recalls

3

15V689000 · Visibility:power Window Devices And Controls

Oct 22, 2015

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

Consequence & remedy

Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.

Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.

12V491000 · Visibility:power Window Devices And Controls

Oct 10, 2012

Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.

Consequence & remedy

Consequence: If the switch overheats, it may melt, possibly resulting in a fire.

Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.

09V388000 · Vehicle Speed Control:accelerator Pedal

Oct 5, 2009

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2004-2010 PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT.

Consequence & remedy

Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.

Remedy: TOYOTA FILED AN AMENDED DEFECT REPORT ON NOVEMBER 25, 2009, STATING THAT DEALERS WILL MODIFY THE ACCELERATOR PEDAL AND, ON CERTAIN VEHICLES, ALTER THE SHAPE OF THE FLOOR SURFACE UNDER THE PEDAL. THESE CHANGES ADDRESS THE RISK OF PEDAL ENTRAPMENT DUE TO INTERFERENCE WITH THE FLOOR MAT. REDESIGNED ACCELERATOR PEDALS WILL BECOME AVAILABLE BEGINNING IN APRIL 2010 AND DEALERS WILL REPLACE ANY MODIFIED PEDAL WITH THE NEW PEDAL IF DESIRED. ALSO, DEALERS WILL REPLACE ANY GENUINE TOYOTA OR LEXUS ALL-WEATHER FLOOR MATS WITH REDESIGNED ALL-WEATHER MATS, OR REPURCHASE THE PREVIOUS MATS FROM OWNERS WHO DO NOT WANT THE NEW ONES. ADDITIONALLY, SOFTWARE MODIFICATIONS WILL BE INSTALLED ON CAMRY, AVALON AND LEXUS ES 350, IS 350 AND IS 250 MODELS THAT WILL ENSURE THAT THE BRAKE OVERRIDES THE ACCELERATOR IN THE EVENT BOTH BRAKE AND ACCELERATOR PEDALS ARE APPLIED. TOYOTA WILL BEGIN MAILING LETTERS TO OWNERS ON DECEMBER 31, 2009. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331, LEXUS AT 1-800-255-3987.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

4

DP22005 · Pedestrian Alert Sounds

Opened Jan 27, 2023 · Closed Aug 7, 2023

Status: closed (inferred from source dates) · Electrical System:propulsion System

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

PE14001 · Brake Actuator Malfunction

Opened Jan 23, 2014 · Closed Aug 22, 2014

Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Air:supply:reservoir/tank; Service Brakes, Electric; Service Brakes, Hydraulic:power Assist

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

Additional source detail variants (4)

Service Brakes, Air:supply:reservoir/tank

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

Service Brakes, Electric

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

Service Brakes, Hydraulic:power Assist

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

Service Brakes

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

EA12006 · Power Window Master Switch Fire

Opened Jun 14, 2012 · Closed Feb 12, 2013

Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Additional source detail variants (3)

Electrical System

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Structure:body

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Unknown Or Other

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

PE12002 · Power Window Master Switch Fire

Opened Feb 6, 2012 · Closed Jun 14, 2012

Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Additional source detail variants (3)

Electrical System

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Structure:body

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Unknown Or Other

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.