← New search

2007 Toyota Camry Hybrid

Owner reports · Recalls · Investigations

Limited comparison data

There is not enough comparable history to draw a useful model-year comparison.

About this comparison →

When problems were reported

Mileage at the reported incident

543 reports with mileage · 59 unknown

NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.

What to inspect

Issues worth paying extra attention to based on owner reports.

  • Service Brakes. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Vehicle Speed Control. Review the 160 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
  • Electronic Stability Control (esc). Review the 115 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →

NHTSA owner reports · September 18, 2026 snapshot.

31 crash reports7 fire reports14 injury reports

Electronic Stability Control (esc) complaints

115 reports
Clear category filter
87,225 miles · Feb 19, 2013
Electronic Stability Control (esc)Service BrakesService Brakes, Hydraulic

THE VEHICLE HAD BEEN FOR THE PAST WEEKS WITH A PULSATING NOISE UNDER THE HOOD, SPECIALLY AT STOPS WAITING FOR A RED LIGHT. YOU CAN FEEL THE PULSATION ON THE PEDAL WHEN YOU DEPRESS THE BRAKE PEDAL. THE NOISE GETS LOUDER THE HARDER YOU PRESS THE PEDAL AND THE CAR SEEMS LIKE ITS TRYING TO MOVE FORWARD ON ITS OWN. NO PROBLEM LIGHTS …

Read full complaint

THE VEHICLE HAD BEEN FOR THE PAST WEEKS WITH A PULSATING NOISE UNDER THE HOOD, SPECIALLY AT STOPS WAITING FOR A RED LIGHT. YOU CAN FEEL THE PULSATION ON THE PEDAL WHEN YOU DEPRESS THE BRAKE PEDAL. THE NOISE GETS LOUDER THE HARDER YOU PRESS THE PEDAL AND THE CAR SEEMS LIKE ITS TRYING TO MOVE FORWARD ON ITS OWN. NO PROBLEM LIGHTS WERE ON THE CONTROL PANEL UNTIL IT REACHED 87,225. AFTER THAT I HAD THE ABS, BRAKE, WARNING, VST LIGHTS ALL ON WITH THE MESSAGE OF CHECK VST ON THE LCD OF THE CONTROL PANEL. TOOK THE CAR TO THE DEALER AND AFTER INSPECTION THEY DETERMINED THAT THE ABS ACTUATOR MODULE HAD TO BE REPLACED. THE QUOTE WAS FOR $2,600!!!!! I STARTED SEARCHING ONLINE AND FOUND OUT SEVERAL OTHER CAMRY OWNERS HAD THE SAME PROBLEM. I'M FILING THE COMPLAINT BECAUSE THIS IS A VERY CRITICAL COMPONENT IN TERMS OF SAFETY AND IT IS FAILING AT A VERY LOW MILEAGE (UNDER 100K) AND SOMETIMES EVEN UNDER 60K. ALSO THE COST OF REPAIR IS SO HIGH YOU HAVE NO CHOICE BUT TO INCREASE THE FINANCIAL BURDEN BECAUSE IT IS A PART THAT IT IS CRITICAL FOR THE CAR'S SAFETY OPERATION. I WOULD NEVER DRIVE A CAR WITH BRAKE PROBLEMS. PLEASE INVESTIGATE THIS ISSUE. *TR UPDATED 08/15/13*LJ

NHTSA ODI #10499211

115,000 miles · Jan 23, 2013
Electronic Stability Control (esc)Service BrakesVehicle Speed Control

THE"CHECK VSC SYSTEM" SENSOR CAME ON WHILE I WAS DRIVING. I WAS DOING APPROXIMATELY 45 MPH ON THE ROAD. THE ROAD CONDITIONS WERE GOOD AND I KEEP UP WITH MAINTENANCE. THE ABS FAILURE LIGHT, BRAKE AND WARNING ICONS. I HAVE IT CHECKED OUT AND I'M TOLD BY TOYOTA CAR'S ABS ACCUMULATOR SYSTEM AND WATER PUMP MUST BE REPLACED AND THA…

Read full complaint

THE"CHECK VSC SYSTEM" SENSOR CAME ON WHILE I WAS DRIVING. I WAS DOING APPROXIMATELY 45 MPH ON THE ROAD. THE ROAD CONDITIONS WERE GOOD AND I KEEP UP WITH MAINTENANCE. THE ABS FAILURE LIGHT, BRAKE AND WARNING ICONS. I HAVE IT CHECKED OUT AND I'M TOLD BY TOYOTA CAR'S ABS ACCUMULATOR SYSTEM AND WATER PUMP MUST BE REPLACED AND THAT THEY HADN'T HAVE SUCH ISSUES BEFORE. AFTER MUCH RESEARCH, THIS IS A COMMON COMPLAINT AMONG TOYOTA CAMRY HYBRID OWNERS. THIS SEEMS TO BE A DESIGN FLAW AND WORSE, MY BREAK PADS AND TIRES ARE BRAND NEW. THIS SHOULDN'T BE AN ISSUE BUT BREAKS PULSATE AND MAKES THE VEHICLE UNSAFE AS YOU CAN'T CONTROL BREAKS WHEN NEEDED, ESPECIALLY, WHILE PARKED ON A INCLINED POSITION. I AM VERY CONCERNED FOR MY SAFETY AND THE SAFETY OF OTHERS IF MY BREAKS WERE TO FAIL BECAUSE TOYOTA HAS FAILED TO RECOGNIZE THIS AS A VITAL RECALL REPAIR. WITHOUT BRAKES YOU CAN KILL OR INJURE SOMEONE AND THAT BAD WATER PUMP CAN CAUSE YOUR ENGINE TO OVERHEAT. PLEASE LOOK INTO THIS AND HAVE TOYOTA TAKE RESPONSIBILITY FOR THIS SITUATION! *TR

NHTSA ODI #10494412

123,000 miles · Nov 1, 2012
Electronic Stability Control (esc)Service Brakes, HydraulicVehicle Speed Control

VSC SYSTEM, CHECK ENGINE, AND EMERGENCY BRAKE LIGHTS COME ON AT THE SAME TIME THE BRAKES STOPPED WORKING PROPERLY. I WAS BRAKING AND THE BRAKE PEDDLE PUSHED BACK AT ME, RELEASING THE BRAKES. WHEN I CONTINUED TO DEPRESS THE BRAKES, THE USUAL RESISTANCE AND BRAKING POWER WAS GONE. I HAD TO PRESS DOWN AS HARD AS I COULD TO GET T…

Read full complaint

VSC SYSTEM, CHECK ENGINE, AND EMERGENCY BRAKE LIGHTS COME ON AT THE SAME TIME THE BRAKES STOPPED WORKING PROPERLY. I WAS BRAKING AND THE BRAKE PEDDLE PUSHED BACK AT ME, RELEASING THE BRAKES. WHEN I CONTINUED TO DEPRESS THE BRAKES, THE USUAL RESISTANCE AND BRAKING POWER WAS GONE. I HAD TO PRESS DOWN AS HARD AS I COULD TO GET THE CAR TO STOP. THIS IS INTERMITTENT AND TENDS TO HAPPEN WHEN THE CAR IS COLD. DEALERSHIP COULD NOT DISCOVER A PROBLEM AS THE COMPUTER DID NOT RECORD AN ERROR. INTERNET RESEARCH INDICATED OTHER TOYOTA HYBRID OWNERS EXPERIENCED THE SAME PROBLEM AND DETERMINED THE CAUSE WAS THE STROKE SENSOR. WHEN I RETURNED THE VEHICLE TO A DIFFERENT DEALERSHIP, THEY INSISTED I CHANGE THE TIRES. THE PROBLEM CONTINUES TO OCCUR. *TR UPDATED 07/30/13*LJ UPDATED 8/22/13 *CN

NHTSA ODI #10482932

119,170 miles · Oct 6, 2012
Electronic Stability Control (esc)Fuel/propulsion System

WHILE MY WIFE WAS DRIVING THE CAR A WARNING ("CHECK VSC SYSTEM") APPEARED IN THE STATUS SCREEN AND ABOUT A MINUTE AFTER, ANOTHER MESSAGE APPEARED ("CHECK HYBRID SYSTEM"). THEN, THE CAR STOPPED RUNNING. THE IMPULSE ALLOWED FOR DRIVING THE CAR TO THE ROAD SIDE. TRIED TO POWER IT BACK WITHOUT SUCCESS. IT WAS REQUIRED TO TOW …

Read full complaint

WHILE MY WIFE WAS DRIVING THE CAR A WARNING ("CHECK VSC SYSTEM") APPEARED IN THE STATUS SCREEN AND ABOUT A MINUTE AFTER, ANOTHER MESSAGE APPEARED ("CHECK HYBRID SYSTEM"). THEN, THE CAR STOPPED RUNNING. THE IMPULSE ALLOWED FOR DRIVING THE CAR TO THE ROAD SIDE. TRIED TO POWER IT BACK WITHOUT SUCCESS. IT WAS REQUIRED TO TOW THE CAR HOME AND THEN TO THE DEALERSHIP FOR DIAGNOSTIC. PRIOR THIS INCIDENT THERE WERE NO PREVIOUS WARNINGS OR SIGNS. *TR

NHTSA ODI #10478893

73,118 miles · Dec 28, 2011
Electronic Stability Control (esc)Service Brakes, HydraulicVehicle Speed Control

MINUTES AFTER LEAVING HOME WHILE TRAVELING 10 MPH IN THE NEIGHBORHOOD, ALL OF THE WARNING LIGHTS ON THE DASH ILLUMINATED - BRAKE, VSC, TIRE, ETC. THE CAR LOST ACCELERATION, THE STEERING BECAME "GUMMY", AND THE BRAKES BECAME "MUSHY". IT TOOK CONSTANT, COMPLETE DEPRESSION OF THE BRAKE PEDAL TO STOP THE CAR OVER A LENGTH OF ABOUT…

Read full complaint

MINUTES AFTER LEAVING HOME WHILE TRAVELING 10 MPH IN THE NEIGHBORHOOD, ALL OF THE WARNING LIGHTS ON THE DASH ILLUMINATED - BRAKE, VSC, TIRE, ETC. THE CAR LOST ACCELERATION, THE STEERING BECAME "GUMMY", AND THE BRAKES BECAME "MUSHY". IT TOOK CONSTANT, COMPLETE DEPRESSION OF THE BRAKE PEDAL TO STOP THE CAR OVER A LENGTH OF ABOUT 25 FEET. I TOOK THE CAR TO 355 TOYOTA IN ROCKVILLE, MD WHERE IT WAS HOOKED TO A COMPUTER, BUT NO PROBLEM WAS DETECTED. THE PROBLEM OCCURRED A SECOND AND THIRD TIME, ONCE MINUTES AFTER STARTUP AND ONCE WHILE TRAVELING AT 30 MPH NOT FAR FROM MY DESTINATION, THANKFULLY. AFTER PARKING THE CAR FOR 2 HOURS, THE CAR DROVE NORMALLY. THE FOURTH TIME THIS PROBLEM OCCURRED, I HAD JUST LEFT THE CAPITAL BELTWAY AND WAS IN THE PROCESS OF BRAKING IN ORDER TO SAFELY ROUND A CLOVERLEAF ONTO RIVER ROAD. THE BRAKES WERE BARELY RESPONSIVE, AND I NARROWLY MISSED CRASHING INTO THE CARS IN FRONT OF ME. I TOOK THE CAR BACK TO 355 TOYOTA ON DECEMBER 27. THE CAR WAS KEPT FOR 24 HOURS. THE MECHANICS COULD FIND NOTHING WRONG WITH IT. I WAS TOLD THIS WAS THE VERY FIRST TIME A PROBLEM SUCH AS MINE HAS BEEN REPORTED TO 355 TOYOTA. A GOOGLE QUERY PROVED THAT THIS PROBLEM IS MORE PERVASIVE THAN THE DEALERSHIP KNOWS OR IS WILLING TO ADMIT KNOWING. *TR UPDATED 7/31/13 *CN THE CONSUMER EXPERIENCED ANOTHER EPISODE AND THE VEHICLE WAS LEFT AT THE DEALER, WHERE THE TECH EXPERIENCED THE PROBLEM HIMSELF. THE TECHNICIAN ADDED BRAKE FLUID. SINCE THE BRAKE FLUID WAS ADDED, THE VEHICLE HAS PERFORMED PERFECTLY.

NHTSA ODI #10441560

Official recalls

3

15V689000 · Visibility:power Window Devices And Controls

Oct 22, 2015

Toyota Motor Company (Toyota) is recalling certain model year 2009-2011 Tundra, Sequoia, Corolla, Corolla Matrix and Scion xB, 2008-2011 Highlander and Highlander Hybrid, 2007 Camry and Camry Hybrid, 2009 Camry and Camry Hybrid, 2006-2011 RAV4, 2006-2010 Yaris, and 2009-2010 Scion xD and Pontiac Vibe vehicles. During the manufacturing of the Power Window Master Switch (PWMS), grease lubricant may have been inconsistently applied to the sliding electrical contacts.

Consequence & remedy

Consequence: If the sliding electrical contacts are not protected by lubricant, debris and moisture that get into the switch may cause a short circuit and the switch assembly may overheat and melt, increasing the risk of a fire.

Remedy: Toyota will notify owners, and dealers will inspect the switch, applying a lubricant if no abnormality is found. If abnormality is found, the PWMS circuit board will be replaced, free of charge. The recall is expected to begin December 20, 2015. Owners may contact Toyota customer service at 1-800-331-4331. Toyota's number for this recall is C0M.

12V491000 · Visibility:power Window Devices And Controls

Oct 10, 2012

Toyota is recalling certain model year 2007-2009 Camry, Camry Hybrid, RAV4, Corolla, Corolla Matrix, Tundra, Sequoia, Highlander, Highlander Hybrid, Yaris, Scion xB, Scion xD and Pontiac Vibe vehicles. The power window master switch assemblies in some of these vehicles were built using a less precise process for lubricating the internal components of the switch assemblies. Irregularities in this lubrication process may cause the power window master switch assemblies to malfunction and overheat.

Consequence & remedy

Consequence: If the switch overheats, it may melt, possibly resulting in a fire.

Remedy: Toyota will notify its owners, and dealers will inspect the switch and apply a special grease that inhibits heat build up or replace any switch damaged by the defect, free of charge. Toyota owners that experience a problem with a switch should not attempt to make repairs, but should contact their Toyota dealer or the Toyota Customer Experience Center at 1-800-331-4331. General Motors will contact the Pontiac Vibe owners affected by this recall and GM dealers will inspect and repair switches as necessary. Those owners may contact Pontiac Customer Care at 1-800-762-2737.

09V388000 · Vehicle Speed Control:accelerator Pedal

Oct 5, 2009

TOYOTA IS RECALLING CERTAIN MODEL YEAR 2004-2010 PASSENGER VEHICLES. THE ACCELERATOR PEDAL CAN GET STUCK IN THE WIDE OPEN POSITION DUE TO ITS BEING TRAPPED BY AN UNSECURED OR INCOMPATIBLE DRIVER'S FLOOR MAT.

Consequence & remedy

Consequence: A STUCK OPEN ACCELERATOR PEDAL MAY RESULT IN VERY HIGH VEHICLE SPEEDS AND MAKE IT DIFFICULT TO STOP THE VEHICLE, WHICH COULD CAUSE A CRASH, SERIOUS INJURY OR DEATH.

Remedy: TOYOTA FILED AN AMENDED DEFECT REPORT ON NOVEMBER 25, 2009, STATING THAT DEALERS WILL MODIFY THE ACCELERATOR PEDAL AND, ON CERTAIN VEHICLES, ALTER THE SHAPE OF THE FLOOR SURFACE UNDER THE PEDAL. THESE CHANGES ADDRESS THE RISK OF PEDAL ENTRAPMENT DUE TO INTERFERENCE WITH THE FLOOR MAT. REDESIGNED ACCELERATOR PEDALS WILL BECOME AVAILABLE BEGINNING IN APRIL 2010 AND DEALERS WILL REPLACE ANY MODIFIED PEDAL WITH THE NEW PEDAL IF DESIRED. ALSO, DEALERS WILL REPLACE ANY GENUINE TOYOTA OR LEXUS ALL-WEATHER FLOOR MATS WITH REDESIGNED ALL-WEATHER MATS, OR REPURCHASE THE PREVIOUS MATS FROM OWNERS WHO DO NOT WANT THE NEW ONES. ADDITIONALLY, SOFTWARE MODIFICATIONS WILL BE INSTALLED ON CAMRY, AVALON AND LEXUS ES 350, IS 350 AND IS 250 MODELS THAT WILL ENSURE THAT THE BRAKE OVERRIDES THE ACCELERATOR IN THE EVENT BOTH BRAKE AND ACCELERATOR PEDALS ARE APPLIED. TOYOTA WILL BEGIN MAILING LETTERS TO OWNERS ON DECEMBER 31, 2009. OWNERS MAY CONTACT TOYOTA AT 1-800-331-4331, LEXUS AT 1-800-255-3987.

Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗

NHTSA investigations

4

DP22005 · Pedestrian Alert Sounds

Opened Jan 27, 2023 · Closed Aug 7, 2023

Status: closed (inferred from source dates) · Electrical System:propulsion System

NHTSA received a petition on or about July 18, 2022, requesting that Federal Motor Vehicle Safety Standard (FMVSS) 141 be applied to all electric and hybrid vehicles operating in the United States. The petition can be reviewed at NHTSA.gov under ODI Number 11486072. FMVSS 141 establishes performance requirements for pedestrian alert sounds for motor vehicles. The standard applies to hybrid and electric vehicles that have a gross vehicle weight rating of 4,536 KG or less or are defined as low-speed vehicles. The standard became fully applicable to all such vehicles manufactured on or after March 1, 2021.On January 27, 2023, NHTSA opened Defect Petition (DP) 22-005 to evaluate the subject matter described in the petition. On June 24, 2023 and as supplemented on June 25, 2023, the petitioner notified NHTSA he was withdrawing his petition. The petitioner indicated that, based on his review of data, there is no justification for asserting potential benefits that could be derived from actions sought by my petition. Based on the petitioner's withdrawal, DP22-005 is closed. Closure of this DP does not represent a determination by NHTSA regarding the subject matter of the petition.

PE14001 · Brake Actuator Malfunction

Opened Jan 23, 2014 · Closed Aug 22, 2014

Status: closed (inferred from source dates) · Service Brakes; Service Brakes, Air:supply:reservoir/tank; Service Brakes, Electric; Service Brakes, Hydraulic:power Assist

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

Additional source detail variants (4)

Service Brakes, Air:supply:reservoir/tank

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

Service Brakes, Electric

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

Service Brakes, Hydraulic:power Assist

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

Service Brakes

On June 25, 2014, Toyota initiated a Warranty Enhancement Program (ZE1) to extend warranty coverage for the brake actuator assembly and skid control ECU/brake pedal stroke sensor in certain MY 2007 to 2011 Toyota Camry hybrid vehicles. Toyota's program covers repairs related to two conditions:internal malfunctions of the Brake Actuator assembly; and overly sensitive monitoring logic for the Brake Pedal Stroke Sensor.Primary coverage provides warranty enhancement until November 30, 2015, with no mileage limitation.After the primary coverage period ends, secondary coverage is provided for 10 years or 150,000 miles from the date of first use, whichever occurs first.In addition, on July 10, 2014, Toyota initiated Limited Service Campaign E0U to replace the Brake Reservoir Tank in MY 2007 through 2011 Toyota Camry hybrid vehicles.The LSC will be available until June 30, 2017, and will only be available at an authorized Toyota dealer.ODI's analysis of failure data determined that the majority of records were related to the Brake Actuator condition, which appeared to be the causal component in 734 complaints/field reports and 864 warranty claims.The Brake Pedal Stroke Sensor (80 reports/189 claims) and Brake Reservoir Tank (91 reports/44 claims) conditions were identified in far fewer records.Analysis of the failure data indicate that each condition provides warning prior to any reduction in power assisted braking, with less than 10 percent of all reports and claims involving diagnostic codes or complaint narratives indicating increased braking effort or reduced brake effectiveness.In addition, most of the incidents in which reduced braking assist appears to have occurred involved operation in a reduced assist mode and not a sudden, complete loss of power assisted braking.ODI assessed reduced assist mode in a subjective driving evaluation which indicated that the brake system provided normal and harddeceleration capability with reasonable increases in pedal effort.Less than one percent of reports and claims analyzed by ODI included evidence indicating a complete loss of power assisted braking occurred and this mode requires operation for a significant period of time with multiple audible and visual warnings.Repair expense was cited in many of the complaints reviewed by ODI, especially those related to the Brake Actuator, which had repair costs exceeding $3,000 according to some complaints.High repair cost appears to have been a factor in the only crash identified by ODI for the fault conditions identified by Toyota, which involved a Brake Actuator failure that was diagnosed but the owner declined repair approximately eight months prior to the reported crash incident.This preliminary evaluation is closed.The closing of this investigation does not constitute a finding that a safety-related defect does not exist.For additional information regarding this investigation, including analysis of the Brake Actuator, Brake Pedal Stroke Sensor, and Brake Reservoir Tank fault conditions and failure experience, see Attachment A to this closing resume.

EA12006 · Power Window Master Switch Fire

Opened Jun 14, 2012 · Closed Feb 12, 2013

Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Additional source detail variants (3)

Electrical System

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Structure:body

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

Unknown Or Other

On October 10, 2012, Toyota initiated a safety recall of approximately 2.5 million U.S. vehicles involving the following models and model years:2007-2009 Camry and Camry Hybrid, 2009 Corolla and Corolla Matrix, 2008 Highlander and Highlander Hybrid, 2007-2009 RAV4, 2008-2009 Scion xB and xD, 2008-2009 Sequoia, 2007-2008 Tundra, 2007-2008 Yaris, and 2009 Pontiac Vibe.See NHTSA recall number 12V-491 for more details, including the affected vehicle manufacture dates for each vehicle model.Note that only early-production 2009 model year vehicles are included in the recall.Toyota and GM dealers will inspect the power window master switch (PWMS) assemblies and apply a specialized grease that inhibits heat build-up.The circuit board in the PWMS may be replaced with a new one if notchy or sticking feeling is observed during the inspection.The failure report summary above shows counts for the vehicles identified at the start of this Engineering Analysis, specifically the approximately 1.4 million vehicles that share an identical PWMS assembly design including, model year 2007-2009 Camry, Camry Hybrid, RAV4, and Yaris built from September 2006 through August 2008, as well as all 2008 Highlander Hybrid.Toyota subsequently identified approximately one million additional vehicles that have a slightly different PWMS design but contain the same defect condition.Note that the totals for complaints and fires shown above may include duplicative reports (between ODI and manufacturer reports).This Engineering Analysis is closed.See attached report for additional information.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10323848, 10360414, 10392622, 10394453, 10411328, 10429983, 10436663, 10446699, 10447416, 10447417, 10447419, 10447444, 10447515, 10447845, 10447947, 10449270, 10450133, 10450568, 10450606, 10450641, 10451821, 10455540, 10455614, 10456353, 10456438, 10457854, 10457955, 10459730, 10460166, 10460691, 10461220, 10462140, 10462200, 10462247, 10462404, 10462705, 10462761, 10464451, 10464769, 10465421, 10466279, 10466667, 10468126, 10468265, 10475230, 10470313, 10470684, 10471551, 10471824, 10472336, 10472910, 10473753, 10473967, 10473969, 10476921, 10477469, 10478563 and 10478657.

PE12002 · Power Window Master Switch Fire

Opened Feb 6, 2012 · Closed Jun 14, 2012

Status: closed (inferred from source dates) · Electrical System; Structure:body; Unknown Or Other

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Additional source detail variants (3)

Electrical System

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Structure:body

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.

Unknown Or Other

ODI has identified certain Toyota vehicles experiencing a higher rate of fire and thermal event incidents among all Toyota vehicles that use the same power window master switch design.They include a total of approximately 1.4 million model year (MY) 2007 through 2009 Camry, Camry Hybrid, RAV4 and Yaris vehicles built from approximately September 2006 through August 2008, as well as all MY 2008 Highlander Hybrid vehicles.This Preliminary Evaluation has been upgraded to an Engineering Analysis (EA12-006) to further study the alleged defect and its consequences.The ODI reports cited above can be viewed at www-odi.nhtsa.dot.gov/owners/SearchNHTSAID under the following identification numbers: 10461220, 10460691, 10460166, 10459730, 10457955, 10457854, 10456438, 10456353, 10455614, 10455540, 10451821, 10450641, 10450606, 10450568, 10450133, 10449270, 10447947, 10447845, 10447515, 10447444, 10447419, 10447417, 10447416, 10446699, 10436663, 10429983, 10411328, 10407290, 10394453, 10392622, 10360414, 10323848.