Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
2040–25K
20725–50K
7750–75K
2075–100K
6100–150K
2150K+
516 reports with mileage · 401 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Electrical System. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Visibility/wiper. Review the 205 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Power Train. Review the 47 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
32 crash reports3 fire reports17 injury reports
What owners actually said
917 reports
38,718 miles · Oct 30, 2019
Engine
TL* THE CONTACT OWNS A 2017 SUBARU OUTBACK. DURING COLD WEATHER, THE VEHICLE FAILED TO START. THE FAILURE OCCURRED EVER SINCE THE VEHICLE WAS PURCHASED ON APRIL 15, 2017. THE VEHICLE WAS TAKEN TO CAPITAL SUBARU (920 CAPITAL EXPRESSWAY AUTO MALL, SAN JOSE, CA 95136) ON THREE DIFFERENT OCCASIONS, BUT THEY WERE NOT ABLE TO REPLICAT…
Read full complaint
TL* THE CONTACT OWNS A 2017 SUBARU OUTBACK. DURING COLD WEATHER, THE VEHICLE FAILED TO START. THE FAILURE OCCURRED EVER SINCE THE VEHICLE WAS PURCHASED ON APRIL 15, 2017. THE VEHICLE WAS TAKEN TO CAPITAL SUBARU (920 CAPITAL EXPRESSWAY AUTO MALL, SAN JOSE, CA 95136) ON THREE DIFFERENT OCCASIONS, BUT THEY WERE NOT ABLE TO REPLICATE THE FAILURE. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE APPROXIMATE FAILURE MILEAGE WAS 38,718.
NHTSA ODI #11277169
20,000 miles · Oct 30, 2019
Visibility/wiper
MY WINDSHIELD SPONTANEOUSLY CRACKED AND SPREAD TO THE POINT WHERE I HAD TO REPLACE IT. THE CAR WAS PARKED IN MY GARAGE WHEN IT CRACKED. AFTER DRIVING THE CAR THE CRACK SPREAD THE ENTIRE SPAN OF THE WINDSHIELD.
NHTSA ODI #11277088
29,000 miles · Oct 29, 2019
Visibility
TL* THE CONTACT OWNS A 2017 SUBARU OUTBACK. THE CONTACT STATED THAT THE WINDSHIELD CRACKED WITHOUT IMPACT OR WARNING. THE VEHICLE WAS TAKEN TO TWO DIFFERENT DEALERS, INCLUDING LITHIA RENO SUBARU (775-800-5534, LOCATED AT 2270 KIETZKE LN, RENO, NV 89502). BOTH DEALERS INSISTED THAT THE WINDSHIELD WAS IMPACTED BY SOMETHING. THE MA…
Read full complaint
TL* THE CONTACT OWNS A 2017 SUBARU OUTBACK. THE CONTACT STATED THAT THE WINDSHIELD CRACKED WITHOUT IMPACT OR WARNING. THE VEHICLE WAS TAKEN TO TWO DIFFERENT DEALERS, INCLUDING LITHIA RENO SUBARU (775-800-5534, LOCATED AT 2270 KIETZKE LN, RENO, NV 89502). BOTH DEALERS INSISTED THAT THE WINDSHIELD WAS IMPACTED BY SOMETHING. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE FAILURE MILEAGE WAS APPROXIMATELY 29,000. THE VIN WAS UNKNOWN.
NHTSA ODI #11276969
39,000 miles · Oct 28, 2019
Unknown Or Other
WINDSHIELD CRACKING.
NHTSA ODI #11271599
12,000 miles · Oct 28, 2019
Unknown Or Other
WITHIN A COUPLE WEEKS OF HAVING TO HAVE OUR WINDSHIELD FIXED, I WAS DRIVING STRAIGHT AHEAD ON A FREEWAY, APPROXIMATELY 70 MPH, WHEN A CRACK STREAKED ACROSS OUR WINDSHIELD. WE COULDN'T FIGURE OUT WHY, THINKING MAYBE A TINY ROCK HIT US. A FEW DAYS LATER WE ASKED SUBARU TO FIX IT, BUT THEY SAID THAT'S NOT WHAT THEY DO AND SENT US T…
Read full complaint
WITHIN A COUPLE WEEKS OF HAVING TO HAVE OUR WINDSHIELD FIXED, I WAS DRIVING STRAIGHT AHEAD ON A FREEWAY, APPROXIMATELY 70 MPH, WHEN A CRACK STREAKED ACROSS OUR WINDSHIELD. WE COULDN'T FIGURE OUT WHY, THINKING MAYBE A TINY ROCK HIT US. A FEW DAYS LATER WE ASKED SUBARU TO FIX IT, BUT THEY SAID THAT'S NOT WHAT THEY DO AND SENT US TO A LOCAL AUTO GLASS COMPANY. THEY SAID THESE NEW WINDSHIELDS WITH ALL THE TECHNOLOGY LIKE EYESIGHT, ETC. SEEM TO MAKE THE WINDSHIELDS MORE FRAGILE. ON JUNE 1ST, 2017 (OUR CAR WAS ONLY 6 MONTHS OLD), HAVING THE WINDSHIELD REPLACED, WE PICKED IT UP TO A TUNE OF $1,485.02. I WONDERED WHEN WE WOULD HAVE TO BE BACK IN FOR ANOTHER FIX. VERY CONCERNING.
NHTSA ODI #11271549
30,000 miles · Oct 28, 2019
Unknown Or Other
WINDSHIELD HAS BROKEN FOR THE 2ND TIME SINCE PURCHASE. BOTH TIMES SUBARU GLASS.
NHTSA ODI #11271493
16,000 miles · Oct 28, 2019
Unknown Or Other
THE WINDSHIELD DEVELOPED A CRACK FROM THE BOTTOM CORNER OF THE DRIVER'S SIDE FOR NO APPARENT REASON WHEN THE CAR WAS GARAGED. THERE WAS NO ROCK OR OTHER DAMAGE TO CAUSE IT. IT HAS SPREAD ACROSS THE WINDSHIELD. THE WINDSHIELD REPLACEMENT IS PROHIBITIVELY EXPENSIVE AND THIS IS A KNOWN PROBLEM TO SUBARU.
NHTSA ODI #11271492
20,000 miles · Oct 27, 2019
Visibility/wiper
WINDSHIELD CRACKED WHILE CAR WAS PARKED.
NHTSA ODI #11271412
20,000 miles · Oct 27, 2019
Visibility/wiper
THE WINDSHIELD CRACKED AND BY THE END OF THE DAY (SITTING IN A PARKING LOT) WAS SEVERAL FEET LONG. I TOOK IT TO THE DEALER SERVICE CENTER AND HAD IT REPLACED. USED MY INSURANCE CLAIM AND PAID OUT OF POCKET.
NHTSA ODI #11271405
45,000 miles · Oct 27, 2019
Visibility/wiper
WINDSHIELD DEVELOPED A CRACK FROM THE VERY TOP EDGE WITHOUT ANY IMPACT OR SIGNS OF DAMAGE. VEHICLE WAS STATIONARY AND IN A COVERED GARAGE.
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence & remedy
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Additional source detail variants (2)
Air Bags:knee Bolster
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Steering:column
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence & remedy
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Additional source detail variants (2)
Service Brakes, Hydraulic:foundation Components:disc:caliper
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Suspension
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration