IllustrationTHE WINDSHIELD IS CRACKING AND IT SEEMS TO BE WITHOUT ANY REASON. THERE IS A VERY TINY DINK THAT CAN BE SEEN, BUT THE CRACK IS SIGNIFICANT COMPARED TO THE SLIGHT DINK. THERE WAS NO INCIDENT THAT OCCURRED PRIOR TO MY NOTICING THE CRACK.
2017 Subaru Outback
Owner reports · Recalls · Investigations
More warning signs than most Outback years
Owner complaints for the 2017 Subaru Outback are substantially higher than the model-year median of 207.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all Outback years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
2040–25K
20725–50K
7750–75K
2075–100K
6100–150K
2150K+
516 reports with mileage · 401 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Electrical System. Review the 391 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Visibility/wiper. Review the 205 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Power Train. Review the 47 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
32 crash reports3 fire reports17 injury reports
Structure complaints
26 reportsTHE DRIVER SIDE DOOR IS RUSTING FROM INSIDE. ISSUE WAS INFORMED TO SUBARU IN 2018 AND IN JAN 2021 THE ISSUE HAS GOTTEN WORSE.
WINDSHIELD IS CRACKING WITHOUT ANY CAUSE. IT CRACKED NEAR THE PASSENGER SIDE WIPER WHILE IT WAS SITTING IN A PARKING GARAGE UNDER NORMAL CONDITIONS. I HAD THE WINDSHIELD REPLACED TODAY, WEATHER WAS PERFECT (SUNNY, 65 DEGREES F), AND IT CRACKED AGAIN, WHILE PARKED, ONLY HOURS AFTER THE REPLACEMENT IN ALMOST THE SAME SPOT..
WE WERE TRAVELING SOUTH ON INTERSTATE 15 AND ABOUT 45 MINUTES INTO MY TRIP TO TAKE MY COUSINS BACK TO THE AIRPORT IN SALT LAKE CITY FROM IDAHO FALLS THE HOOD OF THE CAR JUST FLEW UP AND SMASHED INTO THE WINDSHIELD. THE CARE WAS UN-DRIVABLE AND HAD TO BE TOWED. ULTIMATELY THE INSURANCE COMPANY TOTALED THE VEHICLE. THE WEEKEND …
Read full complaint
WE WERE TRAVELING SOUTH ON INTERSTATE 15 AND ABOUT 45 MINUTES INTO MY TRIP TO TAKE MY COUSINS BACK TO THE AIRPORT IN SALT LAKE CITY FROM IDAHO FALLS THE HOOD OF THE CAR JUST FLEW UP AND SMASHED INTO THE WINDSHIELD. THE CARE WAS UN-DRIVABLE AND HAD TO BE TOWED. ULTIMATELY THE INSURANCE COMPANY TOTALED THE VEHICLE. THE WEEKEND AFTER I WAS BACK IN COLORADO MY BROTHER AND I SAW ANOTHER SUBARU BUT DIFFERENT MODEL THAT IT LOOKED LIKE THE SAME THING HAPPENED. HAVE PICTURES OF THAT AS WELL.
2017 SUBARU OUTBACK. CONSUMER WRITES IN REGARDS TO ISSUES WITH THE GAS AND BRAKE PEDALS. *LD THE CONSUMER STATED WHEN DEPRESSING THE BRAKE PEDAL IT TRAVELS ALL THE WAY DOWN, CAUSING THE DRIVER TO INADVERTENTLY MAKE CONTACT WITH THE GAS PEDAL. THE DEALER WAS NOTIFIED AND STATED THE VEHICLE WAS OPERATING AS DESIGNED. *JS
PARKED MY LEASED 2017 OUTBACK IN MY DRIVEWAY LAST NIGHT WITH NOTHING OVERHEAD, NO TREES, ETC. THIS MORNING THERE WAS A LARGE CRACK IN THE WINDSHIELD WHICH BEGAN AT THE BOTTOM OF THE GLASS ON THE PASSENGER SIDE AND CONTINUED ON FOR OVER 15 INCHES. TOTAL MYSTERY. *TR
I PURCHASED A BRAND NEW 2017 SUBARU OUTBACK, IN NOV 2019, WINDSHIELD CRACK BY ITSELF WITHOUT ANY EXTERNAL INFLUENCE DURING NORMAL DRIVING @ 9200 MILES, GOT NEW ONE REPLACED ON 12/5/19, THEN AFTER 3 MONTHS DRIVING LESS 500 MILES, IT CRACKED AGAIN. MADE REPORT TO SUBARU OF AMERICA, THEY DENY THE DEFECTIVE OF THEIR WINDSHIELD AND R…
Read full complaint
I PURCHASED A BRAND NEW 2017 SUBARU OUTBACK, IN NOV 2019, WINDSHIELD CRACK BY ITSELF WITHOUT ANY EXTERNAL INFLUENCE DURING NORMAL DRIVING @ 9200 MILES, GOT NEW ONE REPLACED ON 12/5/19, THEN AFTER 3 MONTHS DRIVING LESS 500 MILES, IT CRACKED AGAIN. MADE REPORT TO SUBARU OF AMERICA, THEY DENY THE DEFECTIVE OF THEIR WINDSHIELD AND REFUSE TO BE RESPONSIBLE FOR THE REPLACEMENT COST..
MY WINDSHIELD DEVELOPED A CRACK STARTING FROM THE BOTTOM CENTER, RIGHT WHERE THE WINDHIELD HEATING ELEMENT IS. THE VEHICLE WAS IN MOTION BUT NOTHING HIT THE WINDSHIELD, I JUST HEARD A POP AND SAW THE CRACK APPEAR AND IN A MATTER OF MINUTES IT WAS HALF WAY UP. ENDED UP REPLACING THE WINDSHIELD WITH AN AFTERMARKET ONE AFTER SUBARU…
Read full complaint
MY WINDSHIELD DEVELOPED A CRACK STARTING FROM THE BOTTOM CENTER, RIGHT WHERE THE WINDHIELD HEATING ELEMENT IS. THE VEHICLE WAS IN MOTION BUT NOTHING HIT THE WINDSHIELD, I JUST HEARD A POP AND SAW THE CRACK APPEAR AND IN A MATTER OF MINUTES IT WAS HALF WAY UP. ENDED UP REPLACING THE WINDSHIELD WITH AN AFTERMARKET ONE AFTER SUBARU OF AMERICA SAID THEY WON'T COVER IT.
MY WINDSHIELD CRACKED WHILE SITTING IN A PARKING GARAGE DURING A WORKDAY. THE CRACK STARTED OFF ABOUT 12", AND ABOUT A MONTH LATER SPREAD ALL THE WAY ACROSS THE WINDSHIELD.
WINDSHIELD DEVELOPED A CHIP WHICH TURNED INTO A 12 INCH CRACK WITHOUT IMPACT FROM ROCKS OR LARGE ROAD DEBRIS. THE CHIP APPEARED WILL DRIVING ON THE HIGHWAY WHEN THE SOUND OF SAND OR BUGS WAS HEAR TO HIT THE WINDSHIELD BUT WAS NOT ANYTHING THAT WOULD RESULT IN A CHIP THAT WOULD LEAD TO A 12 INCH CRACK. THE WINDSHIELD HAD TO BE RE…
Read full complaint
WINDSHIELD DEVELOPED A CHIP WHICH TURNED INTO A 12 INCH CRACK WITHOUT IMPACT FROM ROCKS OR LARGE ROAD DEBRIS. THE CHIP APPEARED WILL DRIVING ON THE HIGHWAY WHEN THE SOUND OF SAND OR BUGS WAS HEAR TO HIT THE WINDSHIELD BUT WAS NOT ANYTHING THAT WOULD RESULT IN A CHIP THAT WOULD LEAD TO A 12 INCH CRACK. THE WINDSHIELD HAD TO BE REPLACED. COST TO REPLACE THE WINDSHIELD OUT OF POCKET WAS $675.73 PLUS TAX
Official recalls
419V910000 · Air Bags: Air Bag/restraint Control Module
Dec 19, 2019
Subaru of America, Inc. (Subaru) is recalling certain 2016-2017 Outback vehicles. A replacement air bag control module may have been installed that is not compatible with the passenger air bag module, possibly affecting air bag deployment.
Consequence & remedy
Consequence: In the event of a crash necessitating passenger frontal air bag deployment, the air bag may not deploy properly, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will replace the passenger air bag module, free of charge. The recall began February 3, 2020. Owners may contact Subaru customer service at 1-844-373-6614. Subaru's number for this recall is WUX-09.
16V716000 · Air Bags:knee Bolster; Steering:column
Oct 6, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence & remedy
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Additional source detail variants (2)
Air Bags:knee Bolster
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
Steering:column
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Legacy and Outback vehicles manufactured September 21, 2016, to September 23, 2016. In the affected vehicles, the knee guard bracket may not be properly attached to the steering beam assembly.
Consequence: If the knee guard is not properly attached and the driver is not wearing a seatbelt, the knee guard may not be able to properly restrain the driver's lower body in the event of a crash, increasing the risk of injury.
Remedy: Subaru will notify owners, and dealers will inspect the knee guard welding on each vehicle's steering beam, replacing the beam as necessary, free of charge. The recall began November 14, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTL-72.
16V576000 · Service Brakes, Hydraulic:foundation Components:disc:caliper; Suspension
Aug 3, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence & remedy
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Additional source detail variants (2)
Service Brakes, Hydraulic:foundation Components:disc:caliper
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
Suspension
Subaru of America, Inc. (Subaru) is recalling certain model year 2017 Outback vehicles manufactured June 20, 2016, to June 23, 2016. The affected vehicles may have improperly tightened attaching bolts for the front left and right brake calipers, wheel hubs, and the right stabilizer clamp.
Consequence: If any of the front brake caliper, wheel hub or stabilizer clamp attaching bolts loosen or detach, the related components would also become loose and may detach possibly making the vehicle unstable and reducing the braking capability. These conditions would increase the risk of a crash.
Remedy: Subaru has notified owners, and dealers will inspect the bolts for proper torque, and replace any loose bolts, free of charge. The recall began on August 8, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTE-66.
16V292000 · Steering:column
May 11, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.