NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
510 reports90,000 miles · Jul 28, 2020
Engine
NOTED OVER A PERIOD OF SEVERAL WEEKS, AN INCREASE IN EXHAUST NOISE FROM THE FRONT OF THE CAR. THE CABIN WOULD FILL WITH EXHAUST FUMES WHEN STOPPED WITH THE ENGINE RUNNING. I TOOK THE CAR TO THE DEALER TWICE TO HAVE THE ISSUE DIAGNOSED AND BOTH TIMES THEY INDICATED THAT NO ISSUE WAS FOUND. ON THE THIRD TRIP, THEY CONFIRMED A H…
Read full complaint
NOTED OVER A PERIOD OF SEVERAL WEEKS, AN INCREASE IN EXHAUST NOISE FROM THE FRONT OF THE CAR. THE CABIN WOULD FILL WITH EXHAUST FUMES WHEN STOPPED WITH THE ENGINE RUNNING. I TOOK THE CAR TO THE DEALER TWICE TO HAVE THE ISSUE DIAGNOSED AND BOTH TIMES THEY INDICATED THAT NO ISSUE WAS FOUND. ON THE THIRD TRIP, THEY CONFIRMED A HOLE IN THE EXHAUST MANIFOLD AND INITIALLY REFUSED TO REPLACE IT UNDER WARRANTY, EVEN THOUGH THE VEHICLE WAS COVERED UNDER THE PZEV EMISSIONS WARRANTY AND EXTENDED VEHICLE COVERAGE. AFTER POINTING OUT THE PZEV COVERAGE, THE DEALER REPLACED THE MANIFOLD.
NHTSA ODI #11341893
53,800 miles · Jul 16, 2020
Electrical System
2015 SUBARU OUTBACK BATTERY FAILS TO HOLD A CHARGE. I WAS ADVISED IN JANUARY 2020 BY THE SUBARU DEALERSHIP TO REPLACE THE BATTERY, WHICH I DID. THE PROBLEM IS NOW RECURRING AND THE CAR BATTERY WILL NOT HOLD A CHARGE OVER NIGHT. THE DEALERSHIP CLAIMS IT DOES NOT KNOW WHAT THE ISSUE IS. THE CAR HAS BECOME COMPLETELY UNRELIABLE.
NHTSA ODI #11339832
58,878 miles · Jul 7, 2020
Electrical System
2015 SUBARU OUTBACK 3.6L MILEAGE-58969. ALL LIGHTS FLASHING ON DASHBOARD, THEN SOME STOP BUT MANY STAY FLASHING.
NHTSA ODI #11337861
65,000 miles · Jul 5, 2020
Electrical System
I HAVE HAD TO REPLACE MY STOCK SUBARU BATTERY FROM THE DEALER NOW FOUR TIMES. I DRIVE IT FOR WORK EVERYDAY AND EVERY SO OFTEN IT WILL NOT START UP ONE MORNING. I DO NOT LEAVE MY LIGHTS ON, DOME LIGHTS, OR ANY OTHER ELECTRICAL COMPONENTS. IT WAS STATIONARY AND WOULD ALWAYS HAPPEN THE NEXT MORNING, THE BATTERY WOULD BE DRAINED AND…
Read full complaint
I HAVE HAD TO REPLACE MY STOCK SUBARU BATTERY FROM THE DEALER NOW FOUR TIMES. I DRIVE IT FOR WORK EVERYDAY AND EVERY SO OFTEN IT WILL NOT START UP ONE MORNING. I DO NOT LEAVE MY LIGHTS ON, DOME LIGHTS, OR ANY OTHER ELECTRICAL COMPONENTS. IT WAS STATIONARY AND WOULD ALWAYS HAPPEN THE NEXT MORNING, THE BATTERY WOULD BE DRAINED AND THE DEALERSHIP WOULD REPLACE JUST THE BATTERY AS THEIR FIX. MONTHS LATER, IT WOULD ONLY HAPPEN AGAIN ON A BRAND NEW BATTERY FROM THE DEALER.
NHTSA ODI #11337584
44,000 miles · Jul 1, 2020
Structure
MY CAR WAS PARKED IN MY DRIVEWAY AND DEVELOPED A CRACK IN THE FRONT WINDSHIELD. NO IMPACT MARK OR ANYTHING. CRACKED IN THE LOWER PASSENGER SIDE WINDSHIELD LIKE ALL 2015 AND NEWER SUBARU OUTBACKS APPARENTLY DO. THERE ARE NUMEROUS COMPLAINTS ONLINE WITH PEOPLE DETAILING THE EXACT SAME ISSUE YET NO RECALL YET.
NHTSA ODI #11337063
52,000 miles · Jul 1, 2020
Visibility/wiper
WHILE DRIVING MY 2015 SUBARU OUTBACK, I NOTICED THE FRONT WINDSHIELD SPONTANEOUSLY HAD A CRACK THAT STARTED AT THE LOWER PASSENGER SIDE AND RAN DIAGONALLY ACROSS THE WINDSHIELD ABOUT 12", NO EVIDENCE OF BEING HIT BY STONE, ETC.
NHTSA ODI #11331954
25,600 miles · Jun 29, 2020
Engine
TL* THE CONTACT OWNS A 2015 SUBARU OUTBACK. THE CONTACT STATED THAT WHEN THE VEHICLE WAS TAKEN TO AUSTIN SUBARU (8100 BURNET ROAD, AUSTIN, TX 78757 PHONE (512)220-0930) TO BE REPAIRED UNDER NHTSA CAMPAIGN NUMBER: 15V502000 (POWER TRAIN), THE MECHANIC FOUND AN INTERNAL OIL LEAK AND NEEDED TO REMOVE THE ENGINE TO BE ABLE TO CORREC…
Read full complaint
TL* THE CONTACT OWNS A 2015 SUBARU OUTBACK. THE CONTACT STATED THAT WHEN THE VEHICLE WAS TAKEN TO AUSTIN SUBARU (8100 BURNET ROAD, AUSTIN, TX 78757 PHONE (512)220-0930) TO BE REPAIRED UNDER NHTSA CAMPAIGN NUMBER: 15V502000 (POWER TRAIN), THE MECHANIC FOUND AN INTERNAL OIL LEAK AND NEEDED TO REMOVE THE ENGINE TO BE ABLE TO CORRECT THE ENGINE OIL LEAK. THE CONTACT STATED THAT THE DEALER REPLACED ENGINE RINGS, CYLINDER HEADS, AND INSTALLED A LONGER LASTING SILICONE SEALER. THE VEHICLE WAS REPAIRED. THE VEHICLE WAS OUT OF WARRANTY HOWEVER, THE MANUFACTURER REPAIRED THE ENGINE OIL LEAK FAILURE AS A GOOD WILL OFFER. THE FAILURE MILEAGE WAS 25,600.
NHTSA ODI #11331439
18,000 miles · Jun 15, 2020
Electrical System
BATTERY DISCHARGES WHEN NOT DRIVEN FREQUENTLY. SUBARU TECH SUGGESTED PURCHASING LARGER BATTERY AS OEM IS NOT ADEQUATE. DATE OF EVENT IS EST. *TR
NHTSA ODI #11328953
66,000 miles · Jun 12, 2020
Visibility/wiper
WINDSHIELD CRACKED, STARTING AT HEATING ELEMENT AND GREW TO ENTIRE WINDSHIELD. MFR ADMITTED FAULT (I HAVE DOCUMENTATION) BUT WOULD NOT COVER FULL COST OF REPAIR. VEHICLE WAS STATIONARY WHEN CRACK APPEARED AND HAD BEEN STATIONARY FOR SOME TIME DUE TO COVID-19 STAY AT HOME GUIDELINES. *TR
NHTSA ODI #11328454
69,000 miles · Apr 6, 2020
Electrical SystemEngine
TL* THE CONTACT OWNS A 2015 SUBARU OUTBACK . THE CONTACT STATED THAT THE VEHICLE FAILED TO START. THERE WERE NO WARNING LIGHTS ILLUMINATED. THE LOCAL DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS CONTACTED BUT NO FURTHER ASSISTANCE WAS PROVIDED. THE FAILURE MILEAGE WAS 69,000.
NHTSA ODI #11320331
Official recalls
5May 11, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Apr 27, 2016
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Legacy and Outback vehicles manufactured on July 20, 2015. The brake fluid used in these vehicles may contain excess moisture which may adversely affect the performance of the electronic stability control system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 126, "Electronic Stability Control Systems."
Consequence & remedy
Consequence: Poor performance of the electronic stability control system when it is activated may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Subaru will notify owners, and dealers will perform an ABS activation, then flush and replace the brake fluid, free of charge. The recall began on May 20, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTC-64.
Aug 10, 2015
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Jun 12, 2015
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Legacy vehicles manufactured March 10, 2014, to April 16, 2015, Outback vehicles manufactured February 24, 2014, to April 16, 2015, Impreza vehicles manufactured September 9, 2014, to April 14, 2015, XV Crosstrek vehicles manufactured October 16, 2014, to April 15, 2015, and 2016 WRX vehicles manufactured March 23, 2015, and equipped with the Eyesight Driver Assist System. If the switch that activates the brake lights fails, the automatic pre-collision braking component of the driver assist system will not function.
Consequence & remedy
Consequence: If the automatic pre-collision braking system does not function as intended, the vehicle will not react to an obstacle in its path, increasing the risk of a crash.
Remedy: Subaru will notify owners, and dealers will reprogram the driver assist system, free of charge. The recall began on July 20, 2015. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WQS-54.
Additional source detail variants (2)
Forward Collision Avoidance: Crash Imminent Braking
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Legacy vehicles manufactured March 10, 2014, to April 16, 2015, Outback vehicles manufactured February 24, 2014, to April 16, 2015, Impreza vehicles manufactured September 9, 2014, to April 14, 2015, XV Crosstrek vehicles manufactured October 16, 2014, to April 15, 2015, and 2016 WRX vehicles manufactured March 23, 2015, and equipped with the Eyesight Driver Assist System. If the switch that activates the brake lights fails, the automatic pre-collision braking component of the driver assist system will not function.
Consequence: If the automatic pre-collision braking system does not function as intended, the vehicle will not react to an obstacle in its path, increasing the risk of a crash.
Remedy: Subaru will notify owners, and dealers will reprogram the driver assist system, free of charge. The recall began on July 20, 2015. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WQS-54.
Exterior Lighting:brake Lights:switch
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Legacy vehicles manufactured March 10, 2014, to April 16, 2015, Outback vehicles manufactured February 24, 2014, to April 16, 2015, Impreza vehicles manufactured September 9, 2014, to April 14, 2015, XV Crosstrek vehicles manufactured October 16, 2014, to April 15, 2015, and 2016 WRX vehicles manufactured March 23, 2015, and equipped with the Eyesight Driver Assist System. If the switch that activates the brake lights fails, the automatic pre-collision braking component of the driver assist system will not function.
Consequence: If the automatic pre-collision braking system does not function as intended, the vehicle will not react to an obstacle in its path, increasing the risk of a crash.
Remedy: Subaru will notify owners, and dealers will reprogram the driver assist system, free of charge. The recall began on July 20, 2015. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WQS-54.
Sep 19, 2014
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Outback vehicles manufactured January 22, 2014, to August 18, 2014, and equipped with a Subaru accessory trailer hitch assembly. During installation, the trailer hitch mounting nuts may have been overtightened, potentially resulting in failure of the trailer hitch mounting studs.
Consequence & remedy
Consequence: The mounting nut(s) may not provide sufficient force to remain attached to the studs or the studs themselves might break. If this were to happen while a trailer is being towed, the driver might not be able to operate the vehicle as desired or the trailer may detach from the vehicle. Either situation could increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will replace all eight mounting nuts for the trailer hitch assembly, and will inspect all eight mounting studs for damage, free of charge. The recall began on October 7, 2014. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WQN-50.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration