I am on my 3rd battery since May 2015 when the Outback was purchased in El Cajon, California. There have been multiple instances when I prepare to venture out and am unable to as the result of a dead battery. In every instance there was not an obvious instigating factor such as a light inadvertently left on. This situation is ex…
Read full complaint
I am on my 3rd battery since May 2015 when the Outback was purchased in El Cajon, California. There have been multiple instances when I prepare to venture out and am unable to as the result of a dead battery. In every instance there was not an obvious instigating factor such as a light inadvertently left on. This situation is extremely disruptive resulting in my belief that I have an unreliable vehicle that has caused me to miss appointments and meetings. There is also a significant monetary loss in that this is a known and well- publicized issue that will render me unable to recoup market value upon sale of the vehicle. '
NHTSA ODI #11492726
Mileage unknown · Oct 18, 2022
Electrical System
I have had to replace battery sooner than it should have. Also, it seems to be causing an electrical issue with the computer board where all the dashboard warnings are blanking. I have been disconnecting the battery and reconnecting to reset the computer board.
NHTSA ODI #11489815
Mileage unknown · Oct 17, 2022
Electrical System
1st time battery died when car was not in use at least for three days, back in Jan 2022. was replaced. on 10/11/22, after the car was not in use for 4 days, 8 month old battery was died, had to replace, again. Recently received a Subaru Battery settlement letter of a design defect that cuase battery drain.
NHTSA ODI #11489640
Mileage unknown · Sep 26, 2022
Electrical System
I am reporting this deficiency as it is related to: Subaru Battery Drain Products Liability Litigation, No. 1:20-cv-03095-JHR-MJS Deficiency: Battery will discharge to an unusable degree within a relatively short amount of time (10 to 20 min.) when any power is used (radio, cabin lig…
Read full complaint
I am reporting this deficiency as it is related to: Subaru Battery Drain Products Liability Litigation, No. 1:20-cv-03095-JHR-MJS Deficiency: Battery will discharge to an unusable degree within a relatively short amount of time (10 to 20 min.) when any power is used (radio, cabin lights) while engine is off. This has happened 4 times since my purchase of my new 2015 Subaru Outback. I now carry an emergency battery jump starter power unit so as to not be stranded. As the amount of power used is so small there is no warning from the car's system that the discharge is causing such a power drain as to make starting the car not possible. Although I have been contacted by the above class action suit sponsors I am mostly interested in Subaru fixing the electrical system from this obvious deficiency.
NHTSA ODI #11486438
Mileage unknown · Sep 25, 2022
Electrical System
On multiple occasions I have had the tailgate open and the light has drained the battery to the point that it needs a jump start or a battery charging to get it to start back up. On one occasion the tailgate was only left open for 30 minutes and the car would not start due to the battery being drained from it. The battery is in …
Read full complaint
On multiple occasions I have had the tailgate open and the light has drained the battery to the point that it needs a jump start or a battery charging to get it to start back up. On one occasion the tailgate was only left open for 30 minutes and the car would not start due to the battery being drained from it. The battery is in perfect condition as it would start fine any other time.
NHTSA ODI #11486285
Mileage unknown · Aug 15, 2022
Electrical System
Replaced 2 new batteries in 6 months. Batteries went totally dead. Batteries wer replaced by independent shop. Dealer changed battery to a subaru oem battery, checked system, said everything ok. Read about complaints about subaru batteries going dead months apart. Want to find out if there is a defect in subarus.
NHTSA ODI #11479335
Mileage unknown · Jul 10, 2022
Electrical System
Inoperative horn. Traced to continuity failure in steering roll connector, part #83111AL13. No indication of fault and no other apparent continuity failure in adjoining wire paths.
NHTSA ODI #11473223
Mileage unknown · Jun 23, 2022
Electrical System
Battery repeatedly drains when vehicle not used. Have replaced multiple batteries. Alternator checked and functioning.
NHTSA ODI #11470739
Mileage unknown · Jun 21, 2022
Electrical System
On multiple occasions the car battery was drained and required a jump to start. Battery replaced less than 5 months ago. Service technicians unable to identify problem with alternator or parasitic drain.
NHTSA ODI #11470330
Mileage unknown · Jun 13, 2022
Electrical System
The electrical system failed to go into sleep mode after parking the car. The battery was totally drained by morning causing us to find someone to use jumper cables to juice it up again.
Subaru of America, Inc. (Subaru) is recalling certain model year 2016-2017 Legacy and Outback vehicles manufactured February 29, 2016, to May 6, 2016. The steering column on the affected vehicles may have been improperly machined, and as a result, turning the steering wheel may have no effect on the direction of the wheels.
Consequence & remedy
Consequence: The loss of steering ability would increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will inspect the lot number on the steering column, replacing the steering column, as necessary, free of charge. The recall began May 13, 2016. Owners may contact Subaru customer service at 1-800-782-2783 or by visiting http://www.wtd65.service-campaign.com. Subaru's number for this recall is WTD-65. Note: Until the vehicles have been inspected, owners are advised not to drive their vehicles.
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Legacy and Outback vehicles manufactured on July 20, 2015. The brake fluid used in these vehicles may contain excess moisture which may adversely affect the performance of the electronic stability control system. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 126, "Electronic Stability Control Systems."
Consequence & remedy
Consequence: Poor performance of the electronic stability control system when it is activated may result in a loss of vehicle control, increasing the risk of a crash.
Remedy: Subaru will notify owners, and dealers will perform an ABS activation, then flush and replace the brake fluid, free of charge. The recall began on May 20, 2016. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WTC-64.
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence & remedy
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Additional source detail variants (2)
Power Train:driveline:driveshaft
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Power Train:automatic Transmission
Subaru of America, Inc. (Subaru) is recalling certain 2015 and 2016 model year Subaru Legacy 4-Door and Outback vehicles manufactured July 3, 2015, to July 27, 2015. Transmission oil may leak from a deformed seal cap on the propeller shaft yoke.
Consequence: If the transmission oil leaks onto the exhaust pipe, there is a possible risk of fire.
Remedy: Subaru will notify owners, and dealers will replace the propeller shaft, free of charge. The recall began on August 28, 2015. Owners may contact 1-800-782-2783. Subaru's number for this recall is WQU-56.
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Legacy vehicles manufactured March 10, 2014, to April 16, 2015, Outback vehicles manufactured February 24, 2014, to April 16, 2015, Impreza vehicles manufactured September 9, 2014, to April 14, 2015, XV Crosstrek vehicles manufactured October 16, 2014, to April 15, 2015, and 2016 WRX vehicles manufactured March 23, 2015, and equipped with the Eyesight Driver Assist System. If the switch that activates the brake lights fails, the automatic pre-collision braking component of the driver assist system will not function.
Consequence & remedy
Consequence: If the automatic pre-collision braking system does not function as intended, the vehicle will not react to an obstacle in its path, increasing the risk of a crash.
Remedy: Subaru will notify owners, and dealers will reprogram the driver assist system, free of charge. The recall began on July 20, 2015. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WQS-54.
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Legacy vehicles manufactured March 10, 2014, to April 16, 2015, Outback vehicles manufactured February 24, 2014, to April 16, 2015, Impreza vehicles manufactured September 9, 2014, to April 14, 2015, XV Crosstrek vehicles manufactured October 16, 2014, to April 15, 2015, and 2016 WRX vehicles manufactured March 23, 2015, and equipped with the Eyesight Driver Assist System. If the switch that activates the brake lights fails, the automatic pre-collision braking component of the driver assist system will not function.
Consequence: If the automatic pre-collision braking system does not function as intended, the vehicle will not react to an obstacle in its path, increasing the risk of a crash.
Remedy: Subaru will notify owners, and dealers will reprogram the driver assist system, free of charge. The recall began on July 20, 2015. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WQS-54.
Exterior Lighting:brake Lights:switch
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Legacy vehicles manufactured March 10, 2014, to April 16, 2015, Outback vehicles manufactured February 24, 2014, to April 16, 2015, Impreza vehicles manufactured September 9, 2014, to April 14, 2015, XV Crosstrek vehicles manufactured October 16, 2014, to April 15, 2015, and 2016 WRX vehicles manufactured March 23, 2015, and equipped with the Eyesight Driver Assist System. If the switch that activates the brake lights fails, the automatic pre-collision braking component of the driver assist system will not function.
Consequence: If the automatic pre-collision braking system does not function as intended, the vehicle will not react to an obstacle in its path, increasing the risk of a crash.
Remedy: Subaru will notify owners, and dealers will reprogram the driver assist system, free of charge. The recall began on July 20, 2015. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WQS-54.
Subaru of America, Inc. (Subaru) is recalling certain model year 2015 Outback vehicles manufactured January 22, 2014, to August 18, 2014, and equipped with a Subaru accessory trailer hitch assembly. During installation, the trailer hitch mounting nuts may have been overtightened, potentially resulting in failure of the trailer hitch mounting studs.
Consequence & remedy
Consequence: The mounting nut(s) may not provide sufficient force to remain attached to the studs or the studs themselves might break. If this were to happen while a trailer is being towed, the driver might not be able to operate the vehicle as desired or the trailer may detach from the vehicle. Either situation could increase the risk of a crash.
Remedy: Subaru will notify owners, and dealers will replace all eight mounting nuts for the trailer hitch assembly, and will inspect all eight mounting studs for damage, free of charge. The recall began on October 7, 2014. Owners may contact Subaru customer service at 1-800-782-2783. Subaru's number for this recall is WQN-50.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Illustration