IllustrationTAKATA RECALL HAS NOT BEEN RESOLVED. THE DEALER HAS NOT YET RECEIVED THE AIRBAGS.
2006 Saab 9-3
Owner reports · Recalls · Investigations
More warning signs than most 9-3 years
Owner complaints for the 2006 Saab 9-3 are substantially higher than the model-year median of 61.5.
About this comparison →How this year compares
Owner complaints by model year
Compare all 9-3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
260–25K
2425–50K
950–75K
1675–100K
14100–150K
4150K+
93 reports with mileage · 86 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Air Bags. Review the 87 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Service Brakes, Hydraulic. Review the 23 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Seat Belts. Review the 15 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
11 crash reports3 fire reports4 injury reports
What owners actually said
179 reportsTL* TAKATA RECALL. THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISS…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
TL* THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTAC…
Read full complaint
TL* THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE. ...UPDATED 12/28/16 *BF UPDATED 01/04/17.*JB
TAKATA RECALL. I FEEL THAT GM SHOULD BE READY AND COMPLETING THESE RECALLS IN A MUCH MORE TIMELY FASHION. THIS HAS BEEN A KNOWN ISSUE FOR QUITE SOME TIME AND OWNERS SHOUKD NOT HAVE TO LIVE WITH THE WORRY ABOUT THESE POTENTIALLY LETHAL AIRBAGS!
TL* THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT…
Read full complaint
TL* THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
TL* THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT…
Read full complaint
TL* THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE.
WE RECEIVED A LETTER FROM SAAB APPROXIMATELY 1 YEAR AGO AND THE DEALERSHIP (A REGISTERED SAAB SERVICE CENTER) SAYS THAT IT IS NOT AN ACTIVE RECALL, EVEN THOUGH WHEN WE TYPE IN THE VIN NUMBER ON THE NHTSA WEBSITE, IT COMES BACK AS HAVING THIS PARTICULAR RECALL FOR THE AIRBAGS. WE HAVE BEEN CALLING THE DEALERSHIP EVERY MONTH AND T…
Read full complaint
WE RECEIVED A LETTER FROM SAAB APPROXIMATELY 1 YEAR AGO AND THE DEALERSHIP (A REGISTERED SAAB SERVICE CENTER) SAYS THAT IT IS NOT AN ACTIVE RECALL, EVEN THOUGH WHEN WE TYPE IN THE VIN NUMBER ON THE NHTSA WEBSITE, IT COMES BACK AS HAVING THIS PARTICULAR RECALL FOR THE AIRBAGS. WE HAVE BEEN CALLING THE DEALERSHIP EVERY MONTH AND THEY REFUSE TO WORK WITH US AND INSIST THAT THIS RECALL IS NOT REAL. *TR
TL* TAKATA RECALL. THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOTIFIED OF THE ISS…
Read full complaint
TL* TAKATA RECALL. THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS NOTIFIED OF THE ISSUE. THE VIN WAS INVALID. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
TAKATA RECALL. I HAVE BEEN NOTIFIED OF THE RECALL ABOUT 9 MONTHS AGO. THERE HAVE BEEN MULTIPLE DEATHS RELATED TO THE AIRBAG DEPLOYMENT. I FEEL UNSAFE DRIVING MY CAR AND WOULD LIKE A REMEDY NOW. IF YOU CAN NOT FIX THE AIRBAG NOW I WOULD LIKE TO HAVE AN ALTERNATIVE OPTION TO DRIVING THE TICKING TIMEBOMB.
TL* THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT…
Read full complaint
TL* THE CONTACT OWNS A 2006 SAAB 9-3. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 16V063000 (AIR BAGS); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. VIN TOOL CONFIRMS PARTS NOT AVAILABLE.
Official recalls
216V063000 · Air Bags:frontal:driver Side:inflator Module
Feb 3, 2016
General Motors LLC (GM) is recalling certain model year 2006-2011 Saab 9-3 vehicles manufactured May 31, 2002, to February 15, 2011, 2006-2009 Saab 9-5 vehicles manufactured June 7, 2005, to May 28, 2009, and 2008-2009 Saturn Astra vehicles manufactured April 11, 2007, to July 24, 2008. Upon deployment of the driver's frontal air bag, excessive internal pressure may cause the inflator to rupture.
Consequence & remedy
Consequence: In the event of a crash necessitating deployment of the driver's frontal air bag, the inflator could rupture with metal fragments striking the driver or other occupants resulting in serious injury or death.
Remedy: GM will notify owners, and dealers will replace the driver's frontal air bag inflator on Saab 9-3 and 9-5 vehicles and will replace the driver's frontal airbag module on Saturn Astra vehicles, free of charge. The recall began on March 1, 2017. Owners may contact Saab customer service at 1-800-955-9007 or Saturn customer service at 1-800-553-6000. GM's number for this recall is 28810.
14V318000 · Seat Belts:front:retractor
Jun 12, 2014
General Motors LLC (GM) is recalling certain model year 2004-2011 Saab 9-3 Convertible vehicles manufactured July 30, 2003, to February 15, 2011. In the affected vehicles, the driver's side front seat belt retractor may break, causing the seat belt webbing not to retract.
Consequence & remedy
Consequence: In the event of a crash, a seat belt that has not retracted may not properly restrain the seat occupant, increasing their risk of injury.
Remedy: GM will notify owners, and dealers will replace the driver's seat belt retractor, free of charge. The recall began on October 6, 2015. Owners may contact Saab customer service at 1-800-955-9007. GM's number for this recall is 14222. Note: Special Coverage 10086 will replace the passenger side seat belt retractor if it fails, free of charge, for the life of the vehicle.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA08026 · Front Suspension Coil Spring Fracture
Opened Dec 22, 2008 · Closed Jun 4, 2010
Status: closed (inferred from source dates) · Suspension:front:springs:coil Springs
To date, ODI is aware of 142 non-duplicative complaints related to the alleged defect.In addition, ODI is aware of 2,626 subject vehicles with one or more warranty claims related to the alleged defect.In total, ODI is aware of 2,714 unique subject vehicles that have experienced one or more front suspension coil spring fractures.ODI is not aware of any crashes or injuries related to the alleged defect.The engineering design and testing data supplied by GM, along with the frequency of consumer complaints and warranty claims related to the alleged defect, tends to support the position that, in general, the coil springs that fractured on many subject vehicles did not achieve the expected service life.However, in regard to the subject vehicles, a front suspension coil spring fracture itself has little safety consequence, as evidenced by the minimal impact on vehicle ride and handling and by the number of drivers who were unaware of the failure condition for some time until alerted by service personnel.The ratio of tire punctures to coil spring fractures appears low and there are no reports of crashes, deaths or injuries related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will continue to monitor this issue and will take further action if warranted by the circumstances.See the EA08-026 Engineering Analysis Closing Report for more details.
PE08051 · Front Suspension Coil Spring Fracture
Opened Aug 28, 2008 · Closed Dec 23, 2008
Status: closed (inferred from source dates) · Suspension:front:springs:coil Springs
ON AUGUST 28, 2008, THE OFFICE OF DEFECTS INVESTIGATION (ODI) OPENED A PRELIMINARY EVALUATION (PE08-051) TO INVESTIGATE ALLEGED FRONT SUSPENSION COIL SPRING FRACTURES IN CERTAIN MODEL YEAR (MY) 2003-2004 SAAB 9-3 VEHICLES SOLD OR REGISTERED IN SALT BELT STATES.(NOTE: FOR PURPOSES OF THIS INVESTIGATION, THE SALT BELT INCLUDES CONNECTICUT, DELAWARE, THE DISTRICT OF COLUMBIA, ILLINOIS, INDIANA, IOWA, MAINE, MARYLAND, MASSACHUSETTS, MICHIGAN, MINNESOTA, MISSOURI, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT, WEST VIRGINIA AND WISCONSIN).SUBSEQUENT ANALYSIS OF DATA PROVIDED BY GENERAL MOTORS CORP. (GM) HAS LED THE AGENCY TO EXPAND THE SCOPE OF THIS INVESTIGATION TO INCLUDE ALL MY 2003-2006 SAAB 9-3 VEHICLES SOLD OR REGISTERED IN SALT BELT STATES. TO DATE, ODI IS AWARE OF 53 NON-DUPLICATIVE COMPLAINTS AND/OR FIELD REPORTS THAT ALLEGE COIL SPRING FRACTURE IN THE SUBJECT VEHICLES, INCLUDING 23 ALLEGING THE FRACTURED SPRING DAMAGED A TIRE, WITH 16 OF THOSE INVOLVING A TIRE PUNCTURE.ANALYSIS OF WARRANTY DATA PROVIDED BY GM IDENTIFIED 1,218 CLAIMS PAID TO REPAIR SUBJECT VEHICLES THAT EXPERIENCED THE ALLEGED DEFECT, OF WHICH 138 VEHICLES ALSO SUFFERED DAMAGE TO THE ADJACENT TIRE AND OF THOSE, 79 VEHICLES EXPERIENCED A TIRE PUNCTURE.ODI IS NOT AWARE OF ANY CRASHES OR INJURIES RELATED TO THE ALLEGED DEFECT. GM MADE SEVERAL DESIGN CHANGES TO THE COIL SPRINGS AND/OR MCPHERSON STRUT ASSEMBLIES USED IN THE SUBJECT VEHICLES IN AN APPARENT EFFORT TO ADDRESS THE ALLEGED DEFECT CONDITION.HOWEVER, GM MAINTAINS THAT THE SUBJECT VEHICLES REMAIN WELL CONTROLLED IN THE EVENT OF TIRE PUNCTURE, THAT THE RATE OF TIRE PUNCTURE INCIDENTS RELATED TO COIL SPRING FRACTURES IS LOW, AND THAT THE ALLEGED DEFECT DOES NOT POSE AN UNREASONABLE RISK TO MOTOR VEHICLE SAFETY.ACCORDINGLY, THIS INVESTIGATION HAS BEEN UPGRADED TO AN ENGINEERING ANALYSIS (EA08-026) TO FURTHER STUDY THE SAFETY CONSEQUENCES OF THE ALLEGED DEFECT.
PE08005 · Reduced Brake POWER-ASSIST
Opened Jan 28, 2008 · Closed Jun 3, 2008
Status: closed (inferred from source dates) · Service Brakes, Hydraulic:power Assist:vacuum; Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
SAAB AUTOMOBILE AB, A SUBSIDIARY OF GENERAL MOTORS CORP. (GM), MANUFACTURED 12,317 SUBJECT VEHICLES THROUGH FEBRUARY 15, 2008, EQUIPPED WITH THE HIGH FEATURE V6 TURBOCHARGED ENGINE IDENTIFIED BY REGULAR PRODUCTION OPTION LP9.A TANDEM VACUUM BRAKE BOOSTER ASSEMBLY PROVIDES BRAKE POWER-ASSIST.THE ENGINE IS THE PRIMARY VACUUM SOURCE TO THE BOOSTER AND ITS EFFECT IS AMPLIFIED BY A VENTURI.UNDER CERTAIN CONDITIONS, SUCH AS A COLD ENGINE START OR AT HIGH ALTITUDES, AN ELECTRIC VACUUM PUMP (EVP) SUPPLEMENTS ENGINE VACUUM.A PRESSURE SWITCH MEASURES BRAKE BOOSTER VACUUM AND COMMANDS THE EVP WHEN TO TURN ON/OFF.CHECK VALVES ARE LOCATED AT THE INTAKE MANIFOLD, VENTURI, AND PRESSURE SWITCH. GM IDENTIFIED TWO ISSUES THAT AFFECT EVP PERFORMANCE: CORROSION OF ELECTRICAL COMPONENTS INSIDE THE PUMP CAUSED BY MOISTURE INGRESS THROUGH THE AIR OUTLET WHEN THE EVP SHUTS OFF AND THE VACUUM IN A SECTION OF PIPING BETWEEN THE EVP AND THE PRESSURE SWITCH IS RELEASED TO THE ATMOSPHERE; AND SILICONE CONTAMINATION OF THE ELECTRICAL CONTACTS INSIDE THE PRESSURE SWITCH RESULTING IN A NOISY OR IMPEDED ELECTRICAL SIGNAL.GM ADDRESSED EVP PERFORMANCE WITH TWO DESIGN CHANGES.IN NOVEMBER 2007, GM MODIFIED THE RUBBER PROTECTIVE CAP THAT COVERS THE EVP AIR OUTLET TO IMPROVE SEALING AND IN FEBRUARY 2008, GM ADDED A CHECK VALVE TO THE SECTION OF PIPING BETWEEN THE EVP AND THE PRESSURE SWITCH AS CLOSE AS POSSIBLE TO THE EVP IN AN EFFORT TO REDUCE THE BACK FLOW OF MOISTURE THROUGH THE PUMP. IN TOTAL, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 240 SUBJECT VEHICLES AFFECTED BY THE ALLEGED DEFECT.COMPLAINANTS REPORT THAT SYMPTOMS OCCUR IMMEDIATELY AFTER A COLD ENGINE START AND ONLY FOR A SHORT DURATION (30 TO 60 SECONDS), DURING WHICH PERIOD THE AMOUNT OF BRAKE POWER-ASSIST PROVIDED TO THE OPERATOR MAY BE REDUCED DUE TO AN INOPERATIVE EVP.THE SYMPTOMS MAY BE MORE PRONOUNCED THE LONGER THE VEHICLE HAS BEEN PARKED AS THERE IS A NATURAL TENDENCY FOR THE BRAKE BOOSTER TO SLOWLY RELEASE THE VACUUM OVER TIME IF IT IS NOT REPLENISHED.FULL BRAKE POWER-ASSIST CAPABILITY RESUMES AFTER THIS BRIEF COLD START PERIOD OR IMMEDIATELY AFTER A WARM ENGINE START.THE THREE REPORTED CRASHES ALL OCCURRED AT LOW SPEEDS (< 5MPH) WHILE REVERSING FROM A GARAGE OR PARKING SPACE AND RESULTED IN MINIMAL TO MINOR PROPERTY DAMAGE. THE SUBJECT ISSUE DIFFERS FROM A PREVIOUS SAFETY RECALL (05V-236) AFFECTING CERTAIN MODEL YEAR (MY) 2003-2005 SAAB 9-3 VEHICLES EQUIPPED WITH A DEFECTIVE CHECK VALVE THAT COULD BECOME BRITTLE AND FRACTURE, RESULTING IN A LASTING AND TOTAL LOSS OF BRAKE POWER-ASSIST AT ANY TIME.THE DEFECTIVE CHECK VALVE DID NOT MEET LIFETIME DURABILITY REQUIREMENTS AND GM PREDICTED A 100% FAILURE RATE AT LESS THAN 4 YEARS OF SERVICE.IN COMPARISON, GM PREDICTS AN EVP FAILURE RATE OF APPROXIMATELY 6.4% AT 3 YEARS IN SERVICE FOR THE SUBJECT VEHICLES RESULTING IN REDUCED BRAKE POWER-ASSIST FOR A SHORT DURATION.THE SUBJECT ISSUE ALSO DIFFERS FROM A PREVIOUS ODI INFLUENCED SAFETY RECALL (03V-474) TO ADDRESS EVP MOISTURE INGRESS IN CERTAIN MY 2000 VOLVO S40 AND V40 VEHICLES.THE RECALLED VOLVO VEHICLES UTILIZED A STEEL VACUUM PIPE BETWEEN THE EVP AND THE BRAKE BOOSTER.MOISTURE INGRESS AND SUBSEQUENT CORROSION COULD COMPROMISE THE VACUUM PIPE RESULTING IN A LASTING AND TOTAL LOSS OF BRAKE POWER-ASSIST.MOISTURE DOES NOT APPEAR TO HAVE A SIGNIFICANT IMPACT ON THE POLYETHER-ESTER PLASTIC VACUUM PIPE USED IN THE SUBJECT VEHICLES. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION
Additional source detail variants (2)
Service Brakes, Hydraulic:power Assist:vacuum
SAAB AUTOMOBILE AB, A SUBSIDIARY OF GENERAL MOTORS CORP. (GM), MANUFACTURED 12,317 SUBJECT VEHICLES THROUGH FEBRUARY 15, 2008, EQUIPPED WITH THE HIGH FEATURE V6 TURBOCHARGED ENGINE IDENTIFIED BY REGULAR PRODUCTION OPTION LP9.A TANDEM VACUUM BRAKE BOOSTER ASSEMBLY PROVIDES BRAKE POWER-ASSIST.THE ENGINE IS THE PRIMARY VACUUM SOURCE TO THE BOOSTER AND ITS EFFECT IS AMPLIFIED BY A VENTURI.UNDER CERTAIN CONDITIONS, SUCH AS A COLD ENGINE START OR AT HIGH ALTITUDES, AN ELECTRIC VACUUM PUMP (EVP) SUPPLEMENTS ENGINE VACUUM.A PRESSURE SWITCH MEASURES BRAKE BOOSTER VACUUM AND COMMANDS THE EVP WHEN TO TURN ON/OFF.CHECK VALVES ARE LOCATED AT THE INTAKE MANIFOLD, VENTURI, AND PRESSURE SWITCH. GM IDENTIFIED TWO ISSUES THAT AFFECT EVP PERFORMANCE: CORROSION OF ELECTRICAL COMPONENTS INSIDE THE PUMP CAUSED BY MOISTURE INGRESS THROUGH THE AIR OUTLET WHEN THE EVP SHUTS OFF AND THE VACUUM IN A SECTION OF PIPING BETWEEN THE EVP AND THE PRESSURE SWITCH IS RELEASED TO THE ATMOSPHERE; AND SILICONE CONTAMINATION OF THE ELECTRICAL CONTACTS INSIDE THE PRESSURE SWITCH RESULTING IN A NOISY OR IMPEDED ELECTRICAL SIGNAL.GM ADDRESSED EVP PERFORMANCE WITH TWO DESIGN CHANGES.IN NOVEMBER 2007, GM MODIFIED THE RUBBER PROTECTIVE CAP THAT COVERS THE EVP AIR OUTLET TO IMPROVE SEALING AND IN FEBRUARY 2008, GM ADDED A CHECK VALVE TO THE SECTION OF PIPING BETWEEN THE EVP AND THE PRESSURE SWITCH AS CLOSE AS POSSIBLE TO THE EVP IN AN EFFORT TO REDUCE THE BACK FLOW OF MOISTURE THROUGH THE PUMP. IN TOTAL, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 240 SUBJECT VEHICLES AFFECTED BY THE ALLEGED DEFECT.COMPLAINANTS REPORT THAT SYMPTOMS OCCUR IMMEDIATELY AFTER A COLD ENGINE START AND ONLY FOR A SHORT DURATION (30 TO 60 SECONDS), DURING WHICH PERIOD THE AMOUNT OF BRAKE POWER-ASSIST PROVIDED TO THE OPERATOR MAY BE REDUCED DUE TO AN INOPERATIVE EVP.THE SYMPTOMS MAY BE MORE PRONOUNCED THE LONGER THE VEHICLE HAS BEEN PARKED AS THERE IS A NATURAL TENDENCY FOR THE BRAKE BOOSTER TO SLOWLY RELEASE THE VACUUM OVER TIME IF IT IS NOT REPLENISHED.FULL BRAKE POWER-ASSIST CAPABILITY RESUMES AFTER THIS BRIEF COLD START PERIOD OR IMMEDIATELY AFTER A WARM ENGINE START.THE THREE REPORTED CRASHES ALL OCCURRED AT LOW SPEEDS (< 5MPH) WHILE REVERSING FROM A GARAGE OR PARKING SPACE AND RESULTED IN MINIMAL TO MINOR PROPERTY DAMAGE. THE SUBJECT ISSUE DIFFERS FROM A PREVIOUS SAFETY RECALL (05V-236) AFFECTING CERTAIN MODEL YEAR (MY) 2003-2005 SAAB 9-3 VEHICLES EQUIPPED WITH A DEFECTIVE CHECK VALVE THAT COULD BECOME BRITTLE AND FRACTURE, RESULTING IN A LASTING AND TOTAL LOSS OF BRAKE POWER-ASSIST AT ANY TIME.THE DEFECTIVE CHECK VALVE DID NOT MEET LIFETIME DURABILITY REQUIREMENTS AND GM PREDICTED A 100% FAILURE RATE AT LESS THAN 4 YEARS OF SERVICE.IN COMPARISON, GM PREDICTS AN EVP FAILURE RATE OF APPROXIMATELY 6.4% AT 3 YEARS IN SERVICE FOR THE SUBJECT VEHICLES RESULTING IN REDUCED BRAKE POWER-ASSIST FOR A SHORT DURATION.THE SUBJECT ISSUE ALSO DIFFERS FROM A PREVIOUS ODI INFLUENCED SAFETY RECALL (03V-474) TO ADDRESS EVP MOISTURE INGRESS IN CERTAIN MY 2000 VOLVO S40 AND V40 VEHICLES.THE RECALLED VOLVO VEHICLES UTILIZED A STEEL VACUUM PIPE BETWEEN THE EVP AND THE BRAKE BOOSTER.MOISTURE INGRESS AND SUBSEQUENT CORROSION COULD COMPROMISE THE VACUUM PIPE RESULTING IN A LASTING AND TOTAL LOSS OF BRAKE POWER-ASSIST.MOISTURE DOES NOT APPEAR TO HAVE A SIGNIFICANT IMPACT ON THE POLYETHER-ESTER PLASTIC VACUUM PIPE USED IN THE SUBJECT VEHICLES. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION
Service Brakes, Hydraulic:power Assist:vacuum:hoses, Lines/piping, And Fittings
SAAB AUTOMOBILE AB, A SUBSIDIARY OF GENERAL MOTORS CORP. (GM), MANUFACTURED 12,317 SUBJECT VEHICLES THROUGH FEBRUARY 15, 2008, EQUIPPED WITH THE HIGH FEATURE V6 TURBOCHARGED ENGINE IDENTIFIED BY REGULAR PRODUCTION OPTION LP9.A TANDEM VACUUM BRAKE BOOSTER ASSEMBLY PROVIDES BRAKE POWER-ASSIST.THE ENGINE IS THE PRIMARY VACUUM SOURCE TO THE BOOSTER AND ITS EFFECT IS AMPLIFIED BY A VENTURI.UNDER CERTAIN CONDITIONS, SUCH AS A COLD ENGINE START OR AT HIGH ALTITUDES, AN ELECTRIC VACUUM PUMP (EVP) SUPPLEMENTS ENGINE VACUUM.A PRESSURE SWITCH MEASURES BRAKE BOOSTER VACUUM AND COMMANDS THE EVP WHEN TO TURN ON/OFF.CHECK VALVES ARE LOCATED AT THE INTAKE MANIFOLD, VENTURI, AND PRESSURE SWITCH. GM IDENTIFIED TWO ISSUES THAT AFFECT EVP PERFORMANCE: CORROSION OF ELECTRICAL COMPONENTS INSIDE THE PUMP CAUSED BY MOISTURE INGRESS THROUGH THE AIR OUTLET WHEN THE EVP SHUTS OFF AND THE VACUUM IN A SECTION OF PIPING BETWEEN THE EVP AND THE PRESSURE SWITCH IS RELEASED TO THE ATMOSPHERE; AND SILICONE CONTAMINATION OF THE ELECTRICAL CONTACTS INSIDE THE PRESSURE SWITCH RESULTING IN A NOISY OR IMPEDED ELECTRICAL SIGNAL.GM ADDRESSED EVP PERFORMANCE WITH TWO DESIGN CHANGES.IN NOVEMBER 2007, GM MODIFIED THE RUBBER PROTECTIVE CAP THAT COVERS THE EVP AIR OUTLET TO IMPROVE SEALING AND IN FEBRUARY 2008, GM ADDED A CHECK VALVE TO THE SECTION OF PIPING BETWEEN THE EVP AND THE PRESSURE SWITCH AS CLOSE AS POSSIBLE TO THE EVP IN AN EFFORT TO REDUCE THE BACK FLOW OF MOISTURE THROUGH THE PUMP. IN TOTAL, THE OFFICE OF DEFECTS INVESTIGATION (ODI) IS AWARE OF 240 SUBJECT VEHICLES AFFECTED BY THE ALLEGED DEFECT.COMPLAINANTS REPORT THAT SYMPTOMS OCCUR IMMEDIATELY AFTER A COLD ENGINE START AND ONLY FOR A SHORT DURATION (30 TO 60 SECONDS), DURING WHICH PERIOD THE AMOUNT OF BRAKE POWER-ASSIST PROVIDED TO THE OPERATOR MAY BE REDUCED DUE TO AN INOPERATIVE EVP.THE SYMPTOMS MAY BE MORE PRONOUNCED THE LONGER THE VEHICLE HAS BEEN PARKED AS THERE IS A NATURAL TENDENCY FOR THE BRAKE BOOSTER TO SLOWLY RELEASE THE VACUUM OVER TIME IF IT IS NOT REPLENISHED.FULL BRAKE POWER-ASSIST CAPABILITY RESUMES AFTER THIS BRIEF COLD START PERIOD OR IMMEDIATELY AFTER A WARM ENGINE START.THE THREE REPORTED CRASHES ALL OCCURRED AT LOW SPEEDS (< 5MPH) WHILE REVERSING FROM A GARAGE OR PARKING SPACE AND RESULTED IN MINIMAL TO MINOR PROPERTY DAMAGE. THE SUBJECT ISSUE DIFFERS FROM A PREVIOUS SAFETY RECALL (05V-236) AFFECTING CERTAIN MODEL YEAR (MY) 2003-2005 SAAB 9-3 VEHICLES EQUIPPED WITH A DEFECTIVE CHECK VALVE THAT COULD BECOME BRITTLE AND FRACTURE, RESULTING IN A LASTING AND TOTAL LOSS OF BRAKE POWER-ASSIST AT ANY TIME.THE DEFECTIVE CHECK VALVE DID NOT MEET LIFETIME DURABILITY REQUIREMENTS AND GM PREDICTED A 100% FAILURE RATE AT LESS THAN 4 YEARS OF SERVICE.IN COMPARISON, GM PREDICTS AN EVP FAILURE RATE OF APPROXIMATELY 6.4% AT 3 YEARS IN SERVICE FOR THE SUBJECT VEHICLES RESULTING IN REDUCED BRAKE POWER-ASSIST FOR A SHORT DURATION.THE SUBJECT ISSUE ALSO DIFFERS FROM A PREVIOUS ODI INFLUENCED SAFETY RECALL (03V-474) TO ADDRESS EVP MOISTURE INGRESS IN CERTAIN MY 2000 VOLVO S40 AND V40 VEHICLES.THE RECALLED VOLVO VEHICLES UTILIZED A STEEL VACUUM PIPE BETWEEN THE EVP AND THE BRAKE BOOSTER.MOISTURE INGRESS AND SUBSEQUENT CORROSION COULD COMPROMISE THE VACUUM PIPE RESULTING IN A LASTING AND TOTAL LOSS OF BRAKE POWER-ASSIST.MOISTURE DOES NOT APPEAR TO HAVE A SIGNIFICANT IMPACT ON THE POLYETHER-ESTER PLASTIC VACUUM PIPE USED IN THE SUBJECT VEHICLES. A SAFETY-RELATED DEFECT HAS NOT BEEN IDENTIFIED AT THIS TIME AND FURTHER USE OF AGENCY RESOURCES DOES NOT APPEAR TO BE WARRANTED.ACCORDINGLY, THIS INVESTIGATION IS CLOSED.THE CLOSING OF THIS INVESTIGATION