NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
134 reports18,700 miles · Jul 28, 2019
SteeringSuspensionWheelsCrash
DECEMBER 28, 2018 WAS APPROACHING A ROUNDABOUT TRAFFIC ISLAND WHEN TURNING LEFT AND RIGHT THE TRUCK WHEN OUT OF CONTROL AND BOUNCED OFF CURB AND OVER CENTER ISLAND ONE OVER CONCRETE PLANTING BOX UNDER CONSTRUCTION.BLEW PASSENGER SIDE TIRE AND DAMAGING WHEEL,FRONT DIFFERENTIAL TRAINING ARM, DRAG LINK JAM NUT COMPLETELY LOSSE AND …
Read full complaint
DECEMBER 28, 2018 WAS APPROACHING A ROUNDABOUT TRAFFIC ISLAND WHEN TURNING LEFT AND RIGHT THE TRUCK WHEN OUT OF CONTROL AND BOUNCED OFF CURB AND OVER CENTER ISLAND ONE OVER CONCRETE PLANTING BOX UNDER CONSTRUCTION.BLEW PASSENGER SIDE TIRE AND DAMAGING WHEEL,FRONT DIFFERENTIAL TRAINING ARM, DRAG LINK JAM NUT COMPLETELY LOSSE AND CAUSING STEERING WHEEL TO 90 DEGREES LEFT.CLOSE TO HOME USEDFRIENS FLAT BED TRAILER TO TAKE HOME. NEWER TRUCK DID NOT WANT TO BRAND TITLE WITH INSURANCE CLAIM. IT TOOK TWO MONTHS TO SAVE MONEY AS A REPAIR APPROXIMATELY $2300. THE MECHANIC SAID THE DRAG LINK WAS COMPLETELY LOOSE. GOT TRUCK REPAIRED. APPROXIMATELY 30DAYS LATER A RECALL FOR THE DRAG LINK DEFECT. I FEEL LUCKY FOR NOT BEING KILLED. LUCKY I WAS GOING 25MPH.
NHTSA ODI #11235341
Mileage unknown · Jul 26, 2019
Steering
TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT HAD THE VEHICLE SERVICED FOR NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING). DUE TO THE RECALL REMEDY, THE CONTACT WAS NO LONGER ABLE TO OPERATE THE VEHICLE PER FEDERAL MOTOR CARRIER GUIDELINES. AS A RESULT, THE CONTACT HAD THE RECALL REPAIR REVERSED IN ORDER TO UTILIZE THE VEHICLE.…
Read full complaint
TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT HAD THE VEHICLE SERVICED FOR NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING). DUE TO THE RECALL REMEDY, THE CONTACT WAS NO LONGER ABLE TO OPERATE THE VEHICLE PER FEDERAL MOTOR CARRIER GUIDELINES. AS A RESULT, THE CONTACT HAD THE RECALL REPAIR REVERSED IN ORDER TO UTILIZE THE VEHICLE. THE MANUFACTURER WAS NOTIFIED AND STATED THAT THEY WOULD REPAIR THE VEHICLE WITH A NEW AND DIFFERENT REMEDY AT THE CONTACT'S EXPENSE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. *DT*JB *TR 'PARTS OF THIS DOCUMENT HAVE BEEN REDACTED TO PROTECT PERSONALLY IDENTIFIABLE INFORMATION PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).'*JB
NHTSA ODI #11235065
60,000 miles · Jul 17, 2019
SteeringSuspensionUnknown Or OtherCrashInjury
I WAS DRIVING ON THE FREEWAY WITH MY TRAILER LOADED WHEN THE STEERING WHEEL STOPPED CONTROLLING THE DIRECTION OF THE VEHICLE. IT CAUSED ME TO LOSE CONTROL OF THE VEHICLE AND COLLIDE INTO ANOTHER VEHICLE AND HITTING THE FREEWAY MEDIAN WALL. UNKNOWN AS TO THE COMPONENT, I AM STILL WAITING FOR A REPORT.*DT PHOTOS ATTACHED *JB
NHTSA ODI #11232796
42,000 miles · Jul 12, 2019
Tires
TL* THE CONTACT OWNS A 2016 RAM 3500 EQUIPPED WITH NEXEN ROADIAN HTX TIRES, SIZE: LT235/80/R17. WHILE DRIVING 45 MPH, THE LOW TIRE PRESSURE WARNING INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT TIRE SHOP WHERE IT WAS DIAGNOSED THAT THE REAR INNER PASSENGER SIDE TIRE HAD APPROXIMATELY 32 HOLES IN THE CENTER OF TH…
Read full complaint
TL* THE CONTACT OWNS A 2016 RAM 3500 EQUIPPED WITH NEXEN ROADIAN HTX TIRES, SIZE: LT235/80/R17. WHILE DRIVING 45 MPH, THE LOW TIRE PRESSURE WARNING INDICATOR ILLUMINATED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT TIRE SHOP WHERE IT WAS DIAGNOSED THAT THE REAR INNER PASSENGER SIDE TIRE HAD APPROXIMATELY 32 HOLES IN THE CENTER OF THE TIRE. THE CONTACT ALSO MENTIONED THAT DURING THE WEEK OF JULY 3RD, THE FRONT DRIVER'S SIDE TIRE HAD TO BE REPLACED BY AN INDEPENDENT TIRE SHOP. THE VEHICLE WAS TAKEN TO PRINCE FREDERICK CHRYSLER JEEP DODGE (265 SOLOMONS ISLAND RD, PRINCE FREDERICK, MD 20678) AND REPAIRED. THE MANUFACTURER WAS NOT NOTIFIED OF THE FAILURES. THE APPROXIMATE TIRE AND VEHICLE FAILURE MILEAGE WAS 42,000. THE DOT NUMBER WAS UNKNOWN.
NHTSA ODI #11231241
Mileage unknown · May 30, 2019
Electrical System
ON THE SCREEN IT COMES UP (NOT ALL THE TIME) IT COMES UP SERVICE ELECTRONIC BRAKING SYSTEM AND CHECK TRAILER BRAKES( NO TRAILER) & EXHAUST BRAKE AND THE CRUISE CONTROL WILL COME OUT. I HAVE HAD MY TRUCK INTO LARRY MILLER IN BOISE 3-4 TIMES FOR THIS PROBLEM THEY SAY THEY CANNOT FIX IT BECAUSE IT IS NOT DOING IT THEN. IT WAS DOI…
Read full complaint
ON THE SCREEN IT COMES UP (NOT ALL THE TIME) IT COMES UP SERVICE ELECTRONIC BRAKING SYSTEM AND CHECK TRAILER BRAKES( NO TRAILER) & EXHAUST BRAKE AND THE CRUISE CONTROL WILL COME OUT. I HAVE HAD MY TRUCK INTO LARRY MILLER IN BOISE 3-4 TIMES FOR THIS PROBLEM THEY SAY THEY CANNOT FIX IT BECAUSE IT IS NOT DOING IT THEN. IT WAS DOING IT ONE DAY I STOPPED AT PETERSEN DEALERSHIP AND THEY DID A PRINT OUT WITH WHAT IT IS DOING BUT SAID THEY COULDN'T FIX IT BECAUSE I BOUGHT TRUCK AT LARRY MILLER. SO I TOOK THE READ OUT TO LARRY MILLER THEY SAID IT'S NOT DOING IT NOW SO SORRY CAN'T FIX IT! THE TRUCK HAS 32,000 MILES AND HAS BEEN DOING THIS FOR ABOUT 2 YEARS, THE TRUCK IS 3 YEARS OLD. ALSO, I HAVE HAD 5 RECALLS IN 3 YEARS I HAVE NO FAITH IN THIS TRUCK. I FEEL LARRY MILLER IS NOT INTERESTED AND WILL NOT WORK WITH ME TO FIX THIS TRUCK. I HAVE THE PRINTOUT WITH ALL THE PROBLEMS THAT ARE HAPPENING IF YOU WANT TO SEE THEM?
NHTSA ODI #11210810
Mileage unknown · May 16, 2019
Steering
THIS CONCERNS YOUR #V06/NHSTA 19V-021. THE FIX FCA IS DOING FOR THE DEFECTIVE TRACK IS SOME CHEAP WELDING OF THE LOCK NUTS THAT COME LOOSE, INSTEAD OF REPLACING THE TRACK BAR WITH A PROVEN DESIGN AND WHICH IS READILY AVAILABLE FROM BOTH FCA AND AFTERMARKET SUPPLIERS. IT IS A POOR SOLUTION TO A SERIOUS PROBLEM WHICH PUTS MYSELF…
Read full complaint
THIS CONCERNS YOUR #V06/NHSTA 19V-021. THE FIX FCA IS DOING FOR THE DEFECTIVE TRACK IS SOME CHEAP WELDING OF THE LOCK NUTS THAT COME LOOSE, INSTEAD OF REPLACING THE TRACK BAR WITH A PROVEN DESIGN AND WHICH IS READILY AVAILABLE FROM BOTH FCA AND AFTERMARKET SUPPLIERS. IT IS A POOR SOLUTION TO A SERIOUS PROBLEM WHICH PUTS MYSELF, MY FAMILY AND OTHERS ON THEW SAME ROAD AT RISK. PLEASE HELP.....
NHTSA ODI #11208041
Mileage unknown · May 15, 2019
Steering
GENTLEMEN, THIS COMPLAINT IS IN REGARDS TO THE CURRENT V06 RECALL THAT AFFECTS RAM HEAVY DUTY TRUCKS. THE CURRENT FIX OF WELDING COMPONENTS OF THE STEERING SYSTEM BY UNCERTIFIED PEOPLE IN AN UNCONTROLLED ENVIRONMENT IS SOMEWHAT CONCERNING. I HAVE NOT HAD THIS DONE TO MY TRUCK BASED ON THE HIGH NUMBER OF OWNERS DESCRIBING SOME …
Read full complaint
GENTLEMEN, THIS COMPLAINT IS IN REGARDS TO THE CURRENT V06 RECALL THAT AFFECTS RAM HEAVY DUTY TRUCKS. THE CURRENT FIX OF WELDING COMPONENTS OF THE STEERING SYSTEM BY UNCERTIFIED PEOPLE IN AN UNCONTROLLED ENVIRONMENT IS SOMEWHAT CONCERNING. I HAVE NOT HAD THIS DONE TO MY TRUCK BASED ON THE HIGH NUMBER OF OWNERS DESCRIBING SOME OF THEIR RESULTS DONE BY THE DEALER. I WILL INCLUDE A COUPLE OF EXAMPLE PHOTOS. NOT ONLY IS THE WELDING OF COMPONENTS VERY INCONSISTENT, IT CHANGES THE MOLECULAR STRUCTURE OF THE COMPONENTS INVOLVED. IT ALSO RENDERS THE ABILITY TO CORRECTLY DO A FRONT END ALIGNMENT IMPOSSIBLE WITHOUT MAJOR MODIFICATIONS HAS A NEW AND IMPROVED DRAG LINK (#CSZHV061AA) THAT IS AVAILABLE BUT IS VERY RELUCTANT IN SWAPPING THESE OUT. I WOULD GREATLY APPRECIATE AN INVESTIGATION ON THE RESULTS OF THIS CURRENT FIX AND LONG TERM ISSUES TO OWNERS. THE TRUCKS ARE CAPABLE AND DESIGNED TO TOW MASSIVE AMOUNTS OF WEIGHT AND DO SO ON A DAILY BASIS. ALL THE MORE REASON TO FIX IT RIGHT BEFORE MORE ACCIDENTS HAPPEN. THANKS! CONCERNED!! [XXX] INFORMATION REDACTED PURSUANT TO THE FREEDOM OF INFORMATION ACT (FOIA), 5 U.S.C. 552(B)(6).? *PM
NHTSA ODI #11207688
Mileage unknown · May 13, 2019
Steering
TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING) HOWEVER THE MANUFACTURER FAILED TO PROVIDE A PERMANENT REMEDY AND HAD ONLY LIMITED THE REMEDY TO AN INTERIM REPAIR. THE DEALER TRONCALLI CHRYSLER-JEEP-DODGE-RAM (818 ATLANTA HWY, CUMMING, GA 30040, (678) 244-410…
Read full complaint
TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 19V021000 (STEERING) HOWEVER THE MANUFACTURER FAILED TO PROVIDE A PERMANENT REMEDY AND HAD ONLY LIMITED THE REMEDY TO AN INTERIM REPAIR. THE DEALER TRONCALLI CHRYSLER-JEEP-DODGE-RAM (818 ATLANTA HWY, CUMMING, GA 30040, (678) 244-4100) WAS CONTACTED TO SCHEDULE AN APPOINTMENT. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. *BF *AS
NHTSA ODI #11207296
30,000 miles · Apr 27, 2019
Steering
FCA AND THE DEALER REFUSES TO VERIFY THE SAFETY OF MY TRUCK. I BROUGHT MY TRUCK TO THE DEALER FOR RECALL NHTSA 19V-021 (DRAG LINK). I TOLD THE DEALER I WANTED THEM TO INSPECT THE DRAG LINK NUTS TO INSURE THEY WEREN'T COMING OFF. I ALSO SAID I DIDN'T WANT THE NUTS WELDED TO THE DRAG LINK. WELDING THE NUTS WOULD PREVENT ADJUST…
Read full complaint
FCA AND THE DEALER REFUSES TO VERIFY THE SAFETY OF MY TRUCK. I BROUGHT MY TRUCK TO THE DEALER FOR RECALL NHTSA 19V-021 (DRAG LINK). I TOLD THE DEALER I WANTED THEM TO INSPECT THE DRAG LINK NUTS TO INSURE THEY WEREN'T COMING OFF. I ALSO SAID I DIDN'T WANT THE NUTS WELDED TO THE DRAG LINK. WELDING THE NUTS WOULD PREVENT ADJUSTMENT WHEN ALIGNING THE TRUCK IN THE FUTURE. THE DEALER SAID THEY WOULD CUT OFF THE WELDS WHEN DOING THE ALIGNMENT. UNFORTUNATELY THIS WOULD FORCE ME TO RETURN TO THE DEALER, WHICH IS ALMOST AN HOUR AWAY, AND WOULD PREVENT ME FROM GETTING AN ALIGNMENT AT ANY NORMAL SHOP. THIS IS FORCING ME TO PAY MORE MONEY FOR ANY FUTURE ALIGNMENT. THE DEALER REFUSED TO INSPECT THE TRUCK. HE SAID THAT THE ONLY WAY THEY WOULD LOOK AT THE DRAG LINK WAS IF THEY PERFORMED THE ENTIRE RECALL, INCLUDING WELDING THE NUTS. I ASKED IF I LET THEM WELD THE NUTS WOULD THEY REPLACE THE DRAG LINK AT A LATER TIME WHEN THE NEW PART BECAME AVAILABLE, THEY SAID NO. I AM NOW DRIVING A TRUCK THAT I DO NOT KNOW THE SAFETY OF BECAUSE OF THE DEFECTIVE DRAG LINK. I CALLED FCA AND OPENED A CASE (NUMBER AVAILABLE). FCA TOLD ME THIS WAS UP TO THE DEALER. WHY DO I HAVE TO ACCEPT A NON-STANDARD SOLUTION TO A PROBLEM THAT WILL NOT GET ME A NEW, UPGRADED PART, AND WILL COST ME MORE MONEY IN THE FUTURE THROUGH NO FAULT OF MY OWN?
NHTSA ODI #11204089
Mileage unknown · Apr 10, 2019
EngineLatches/locks/linkagesPower Train
TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT RECEIVED NOTIFICATION FOR NHTSA CAMPAIGN NUMBERS: 17V562000 (ENGINE AND ENGINE COOLING), 17V821000 (POWER TRAIN), 18V486000 (STRUCTURE, LATCHES, LOCKS, LINKAGES) AND 19V021000 (STEERING). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL…
Read full complaint
TL* THE CONTACT OWNS A 2016 RAM 3500. THE CONTACT RECEIVED NOTIFICATION FOR NHTSA CAMPAIGN NUMBERS: 17V562000 (ENGINE AND ENGINE COOLING), 17V821000 (POWER TRAIN), 18V486000 (STRUCTURE, LATCHES, LOCKS, LINKAGES) AND 19V021000 (STEERING). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIRS. THE DEALER WAS NOT CONTACTED. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND CONFIRMED PARTS WERE NOT AVAILABLE. THE MANUFACTURER WAS NOT ABLE TO CONFIRM WHEN THE PARTS WERE TO BECOME AVAILABLE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.
NHTSA ODI #11195388
Official recalls
14Jan 16, 2025
Chrysler (FCA US, LLC) is recalling certain 2016-2019 Ram 3500, Ram 1500, 2016-2020 Ram 2500, and 2016 Ram 3500 Cab Chassis vehicles. The right and left side curtain air bag inflators may rupture due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator rupture may result in sharp metal fragments striking occupants, resulting in injury.
Remedy: Dealers will replace one or both side curtain air bags, as necessary, free of charge. Owner notification letters were mailed February 13, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's numbers for this recall are 05C, 09C, and 10C.
Aug 12, 2021
Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
Consequence & remedy
Consequence: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
Remedy: Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.
Additional source detail variants (2)
Air Bags:side/window:curtain:inflator
Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
Consequence: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
Remedy: Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.
Air Bags:side/window:curtain
Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
Consequence: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
Remedy: Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.
May 27, 2021
Chrysler (FCA US, LLC) is recalling certain 2012-2021 RAM 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles. Incorrect information in the Service and Owner's Manuals may cause the flanged lug nuts to be over-tightened, which could result in a broken wheel stud and possible wheel separation.
Consequence & remedy
Consequence: Wheel separation can cause a vehicle crash.
Remedy: Dealers will update the torque specification in the owner's manual and other published service documents. Dealers will also inspect the vehicle's wheel studs, replacing them if necessary, free of charge. Owner notification letters were mailed on November 30, 2021. Campaign Y36 owner notification letters were mailed on November 30, 2021. Campaign Y26 owner notification letters were mailed on December 1, 2021. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's numbers for this recall are Y26 and Y36.
May 9, 2019
Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 foot bed and a power locking tailgate. On August 29, 2019 Chrysler expanded the recall to include an additional 693,128 model year 2013-2014 Ram 1500, 2500 and 3500 pickup trucks. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence & remedy
Consequence: If the tailgate opens while the vehicle is being driven, cargo may fall out the vehicle and create a road hazard, increasing the risk of crash.
Remedy: Chrysler will notify owners, and dealers will repair the tailgate latch, free of charge. The recall began May 23, 2019. Chrysler is expected to notify owners of the expanded population on October 18, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's number for this recall is V44. Note: 2015-2017 MY Ram 1500 pickup trucks with truck beds other than 8 foot, are currently covered under NHTSA recall 18V-486 for this issue.
Jan 25, 2019
Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
Consequence & remedy
Consequence: A drag link separation can cause a loss of steering control, increasing the risk of crash.
Remedy: Chrysler will notify owners, and dealers will check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The recall began March 22, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V06.
Jul 27, 2018
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence & remedy
Consequence: If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.
Additional source detail variants (2)
Latches/locks/linkages:tailgate:latch
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence: If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.
Structure:body:tailgate
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence: If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Dec 20, 2017
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
Consequence & remedy
Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
Sep 12, 2017
Chrysler (FCA US LLC) is recalling certain 2013-2017 RAM 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, equipped with Cummins 6.7L Turbo Diesel engines that have Concentric-brand water pumps without a vent hole. These water pumps may leak coolant.
Consequence & remedy
Consequence: The leaking water pump can increase the risk of an engine compartment fire.
Remedy: Chrysler will notify owners, and dealers will replace the water pumps, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T51.
Aug 10, 2017
Streetcar ORV LLC, dba American Expedition Vehicles (AEV) is recalling certain 2013-2017 RAM 2500 and 3500 heavy duty trucks, modified by AEV to be equipped with cast aluminum Katla 8.5" road wheels. The outer surface of the wheel may fracture, resulting in rapid air loss.
Consequence & remedy
Consequence: If the wheel fractures, a loss of vehicle control can occur, increasing the risk of a crash.
Remedy: AEV will notify owners, and dealers will replace the wheels with wheels of similar value, free of charge. The recall began on August 30, 2017. Owners may contact AEV customer service at 1-248-926-0256 extension 500.
May 9, 2017
Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag and the seat belt pretensioner will be disabled from deploying.
Consequence & remedy
Consequence: If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.
Remedy: Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.
Additional source detail variants (2)
Air Bags:side/window:curtain
Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag and the seat belt pretensioner will be disabled from deploying.
Consequence: If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.
Remedy: Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.
Air Bags
Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag and the seat belt pretensioner will be disabled from deploying.
Consequence: If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.
Remedy: Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.
Jul 1, 2016
Chrysler (FCA US LLC) is recalling certain model year 2016 Ram 3500 trucks manufactured July 24, 2015, through January 7, 2016, and 2016 Ram 4500/5500 trucks manufactured July 24, 2015, through October 8, 2015. The transfer case may have been manufactured with a misshapen main output shaft, creating voids that may cause a shaft fracture.
Consequence & remedy
Consequence: If the main output shaft fractures, the vehicle may lose motive power, increasing the risk of a crash. Additionally, the driver may be unable to place the vehicle in PARK, increasing the risk of a vehicle rollaway.
Remedy: Chrysler will notify owners, and dealers will replace the transfer case, free of charge. The recall began on August 11, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S48.
Sep 23, 2015
Chrysler (FCA US LLC) is recalling certain model year 2016 Ram 2500, 3500, 3500 Cab Chassis and 4500/5500 Cab Chassis trucks manufactured July 31, 2015, to August 13, 2015 and equipped with a 6.7L Cummins Diesel engine. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.
Consequence & remedy
Consequence: An engine that stalls without warning increases the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the ECM, free of charge. The recall began on December 21, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R52.
Additional source detail variants (2)
Electrical System:ignition:module
Chrysler (FCA US LLC) is recalling certain model year 2016 Ram 2500, 3500, 3500 Cab Chassis and 4500/5500 Cab Chassis trucks manufactured July 31, 2015, to August 13, 2015 and equipped with a 6.7L Cummins Diesel engine. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.
Consequence: An engine that stalls without warning increases the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the ECM, free of charge. The recall began on December 21, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R52.
Engine And Engine Cooling:engine
Chrysler (FCA US LLC) is recalling certain model year 2016 Ram 2500, 3500, 3500 Cab Chassis and 4500/5500 Cab Chassis trucks manufactured July 31, 2015, to August 13, 2015 and equipped with a 6.7L Cummins Diesel engine. In the affected vehicles, the Engine Control Module (ECM) may short circuit, causing the engine to stall without warning.
Consequence: An engine that stalls without warning increases the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will replace the ECM, free of charge. The recall began on December 21, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R52.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3RQ25003 · Post Recall Remedy Brake Transmission Shift Interlock (btsi) Failure
Opened Jul 3, 2025 · No close date supplied
Status: open (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:gear Position Indication (prndl)
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Power Train:automatic Transmission:gear Position Indication (prndl)
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
EA19004 · Steering Loss Due To Linkage Separation
Opened Dec 1, 2019 · Closed Nov 20, 2025
Status: closed (inferred from source dates) · Steering:linkages:drag:link:connection
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18016 to investigate alleged drag link failures in the steering system on model year (MY) 2015 and 2016 Ram 2500 trucks manufactured by FCA US, LLC (FCA). The drag link failures were found to be due to a safety defect with the steering linkage where the drag link adjustable connector (used to adjust the steering system), held in position by two opposing jam nuts, can loosen. The loosening of this part can lead to wear and deterioration of the threads and eventual separation of the drag link, causing loss of steering. During the course of PE18016, it was found that two styles of drag link were used by FCA on the subject vehicles. The subject vehicles consist of two drivetrain types including four-wheel drive (4WD) and two-wheel drive (2WD). The 4WD and 2WD trucks used drag links of differing design but both incorporated the same threaded connector. In January 2019 FCA issued recall 19V-021 to address a potential loss of steering control in certain Model Year (MY) 2013-2018 4WD RAM 2500 and 3500 trucks. The trucks using the 2WD style drag link were not included in the scope of recall 19V-021. ODI upgraded PE18016 to an Engineering Analysis EA19004 on December 12, 2019. The purpose of EA19004 was to investigate if the root cause of the safety defect addressed by recall 19V-201 also affected the 2WD trucks and evaluate FCA’s rationale for not including them. ODI also monitored incoming consumer complaints regarding the remedy associated with 19V-021 and evaluated the suitability and long-term effectiveness of the prescribed repair. In the Defect Information Report submitted for recall 19V-021, FCA stated that the outboard jam nut could loosen and result in damage to the threading of the steering drag link connector. This could cause a separation in the drag link resulting in a loss of steering control. FCA determined that only the 4WD style drag link was affected and did not recall trucks with the 2WD style drag link due to design differences that made it unsusceptible to this failure mode. The repair remedy called for the steering coupler to be tightened to the proper torque prior to the jam nut being spot welded to the coupler body. If the coupler has already become detached or correct torque cannot be obtained, the drag link is to be replaced with an updated unit that went into production on the MY2019 RAM trucks.This updated unit uses a clamp to secure the coupler in place of the jam nuts used on original style components. In order to determine if the 2WD drag link was susceptible to the same defect found on the 4WD vehicles, ODI requested that our Vehicle Research and Test Center (VRTC) conduct testing on both RAM 2500 4WD and 2WD trucks. This testing was to determine operating conditions that might lead to loosened jam nuts of the recalled 4WD design and recreate these conditions on the 2WD vehicles to discover whether the 2WD design would also experience the loosening defect. Results from VRTC’s dynamic testing indicated that when the jam nuts are significantly under-torqued, they may loosen further from regular vehicle operation on the 4WD vehicles. Further, VRTC testing does not refute FCA’s assertion that the failure mechanism does not exist in the 2WD steering system. At the time of this closing resume, ODI has only received two allegations of drag link separation on 2WDvehicles.Neither could be validated as resulting from loose jam nuts. Since the release of recall 19V-021 ODI has received consumer complaints regarding the appearance of the spot weld applied to the defective drag link and the inability to have the steering properly aligned after welding of the jam nut. In September 2023, FCA provided owners with a supplemental Vehicle Alignment Clarification notification that provided information on an updated alignment procedure. Regarding the spot weld remedy used on the 4WD vehicles, ODI is concerned about the remedy in that during an alignment by a non-dealer repair facility, the spot weld might not be replaced after the alignment. To date there is no complaint trend of post alignment drag link separations, weld failures or other safety related incidents on remedied vehicles. This investigation is being closed with no further action. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances.
PE18016 · Steering Loss Due To Linkage Separation
Opened Dec 17, 2018 · Closed Dec 12, 2019
Status: closed (inferred from source dates) · Steering:linkages:drag:link:connection
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 18-016 to investigate the steering system on model year (MY) 2015 and 2016 Ram 2500 manufactured by FCA US, LLC (FCA). Four complaints were received alleging separation of the drag link, a steering linkage that connects between the right front steering knuckle and the pitman arm on the steering box output shaft. The failures were found to be at a threaded coupler within the drag link used for adjusting the length of the linkage during routine maintenance (alignment) of the steering system.Once separation occurs, turning the steering wheel has no effect, and there is no way for the driver to control or maintain the direction of the vehicle. During the investigation, it was determined that the same threaded coupler was used on two different drag link designs FCA manufactured on MY 2013-2018 Ram 2500 and 3500 pickups. FCA refers to the designs as either 4x2 or 4x4 style. In both designs, the coupler is prevented from turning on the drag link via two jam nuts that are tightened against the coupler. In its response to NHTSA's March 15, 2019, Information Request (IR) letter, FCA identified 48 incidents alleging separation of the steering linkage at the coupler resulting in a loss of steering control. Of those, 13 involved a crash, one of which resulted in an injury. All of the separations involved the 4x4 style drag link. Additionally, FCA's IR response refers to over 300 4x4 style equipped vehicles that experienced, or may have experienced loosening of one or more coupler jam nuts. On January 25, 2019, FCA submitted a Defect Information Report (DIR) initiating NHTSA Recall No. 19V-021. In its DIR, FCA stated that the outboard jam nut in certain MY 2013-2018 Ram 2500 and 3500 could loosen potentially resulting in damage to the coupler and/or drag link threading allowing one end of the drag link to separate. The DIR notes that drag link separation results in loss of steering control, which in turn can cause a crash without warning. FCA's DIR did not identify a root cause for the defect, however it posits that an improperly torqued outboard jam nut could loosen, and with long-term vehicle use, cause damage to the outer link bar and/or coupler threads due to relative motion between the two components. The scope of Recall 19V-021 included vehicles with the 4x4 style drag link only. Also discussed in its IR response, FCA noted that the 4x2 style drag link contains a design difference (the outboard portion of the drag link is straight while the 4x4 style contains a bend) which it suggests may result in differences in the mechanical (bending) loads presented at the coupler and jam nut interface. Moreover, the DIR states that While root cause of the 4x4 style defect has not been established, FCA US believes that bending loads on the drag link is, at least, a causal contributing factor. FCA notes it did not identify any reports alleging 4x2 style separation as well as only three reports of loosening of jam nuts, two of which resulted in loosening that provided obvious warning to the vehicle operator, indicating a different failure mode.NHTSA is upgrading this investigation to Engineering Analysis (EA) 19-004 in order to continue to monitor the subject 4x2 style vehicles for evidence of field failures. Additionally, in conjunction with NHTSA's Vehicle Research and Test Center, ODI intends to more thoroughly study potential root cause(s) of the 4x4 style defect mechanism, and if identified, will seek to determine if the 4x2 drag link is susceptible to the same mechanism(s). NHTSA will also evaluate the long-term suitability of the recall
Illustration