NHTSA owner reports · September 18, 2026 snapshot.
What owners actually said
114 reports37,203 miles · Mar 16, 2020
Steering
TL* THE CONTACT OWNS A 2013 RAM 3500. THE CONTACT STATED THAT THE VEHICLE WAS REPAIRED UNDER NHTSA CAMPAIGN NUMBER: 18E096000 (STEERING) AT THE HADDAD DODGE RAM LOCATED AT (3000 HARRIS RD, BAKERSFIELD, CA 93313). THE CONTACT STATED THAT THE TECHNICIAN PERFORMED AN INTERIM REPAIR. THE CONTACT STATED THAT THE VEHICLE ALSO REQUIRED…
Read full complaint
TL* THE CONTACT OWNS A 2013 RAM 3500. THE CONTACT STATED THAT THE VEHICLE WAS REPAIRED UNDER NHTSA CAMPAIGN NUMBER: 18E096000 (STEERING) AT THE HADDAD DODGE RAM LOCATED AT (3000 HARRIS RD, BAKERSFIELD, CA 93313). THE CONTACT STATED THAT THE TECHNICIAN PERFORMED AN INTERIM REPAIR. THE CONTACT STATED THAT THE VEHICLE ALSO REQUIRED AN ALIGNMENT HOWEVER, DEALERS DECLINED TO PERFORM THE ALIGNMENT UNTIL THE REMEDY WAS FINALIZED. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE BUT OFFERED NO ASSISTANCE. THE APPROXIMATE FAILURE MILEAGE WAS 37,203.
NHTSA ODI #11318223
102,000 miles · Dec 2, 2019
Steering
THE VEHICLE WAS TAKEN IN FOR A FRONT END ALIGNMENT. WHEN THE TECHNICIAN LOOSENED THE TUBE RETAINING CLAMP TO ADJUST THE OUTER TIE ROD, ONE SIDE OF THE THREADED PORTION OF THE ADJUSTER TUBE, SOCKET, TIE ROD END (68369910AC) FELL ON THE GROUND. THE METAL WALL SHEARED AT THE START OF THE ADJUSTMENT THREADS AND SHOWED SIGNS OF META…
Read full complaint
THE VEHICLE WAS TAKEN IN FOR A FRONT END ALIGNMENT. WHEN THE TECHNICIAN LOOSENED THE TUBE RETAINING CLAMP TO ADJUST THE OUTER TIE ROD, ONE SIDE OF THE THREADED PORTION OF THE ADJUSTER TUBE, SOCKET, TIE ROD END (68369910AC) FELL ON THE GROUND. THE METAL WALL SHEARED AT THE START OF THE ADJUSTMENT THREADS AND SHOWED SIGNS OF METAL FATIGUE. THE OPPOSITE SIDE WAS FULLY CRACKED IN THE SAME LOCATION BUT HAD NOT SHEARED OFF THE ADJUSTER TUBE, SOCKET, TIE ROD END YET. IT TOOK VERY LITTLE EFFORT TO BREAK THE PIECE OFF BY HAND. FAILURE WOULD HAVE BEEN IMMINENT IF LEFT UNTOUCHED. FAILURE WHILE THE VEHICLE WAS IN OPERATION WOULD HAVE RESULTED IN LOSS OF CONTROL OF THE VEHICLE. THE VEHICLE WAS STATIONARY AT AN ALIGNMENT SHOP. THE ADJUSTER TUBE, SOCKET, TIE ROD END IS IDENTIFIED AS PART (1) IN THE ATTACHED DRAWING. FAILURE POINT IS AT THE END WHERE ADJUSTER TUBE (2) IS THREADED IN AND TUBE RETAINING CLAMPS (15) AND (16). PICTURES OF THE FAILED COMPONENT ARE ATTACHED.
NHTSA ODI #11286400
104,000 miles · Nov 8, 2019
Electrical SystemSteering
STEERING CUPLING UNDER DASH HAS SLACK MAKING STEERING LOOSE AND ALTERNATOR PROBLEMS TRUCK ONLY HAS 113609 MILES CHRYSLER CORP SAYS IT'S NOT A PROBLEM AND MORE RECALLS ARE SHOWING ON IT DRIVING ON OPEN ROAD CONSTANTLY WORKING STEERING WHEEL TO KEEP IN STRAIGHT LINE ON THE ROAD CITY DRIVING IS AS BAD SITTING STILL IT HAS ABOUT HAL…
Read full complaint
STEERING CUPLING UNDER DASH HAS SLACK MAKING STEERING LOOSE AND ALTERNATOR PROBLEMS TRUCK ONLY HAS 113609 MILES CHRYSLER CORP SAYS IT'S NOT A PROBLEM AND MORE RECALLS ARE SHOWING ON IT DRIVING ON OPEN ROAD CONSTANTLY WORKING STEERING WHEEL TO KEEP IN STRAIGHT LINE ON THE ROAD CITY DRIVING IS AS BAD SITTING STILL IT HAS ABOUT HALF INCH OR MORE LOOSE PLAY IN STEERING
NHTSA ODI #11279089
104,000 miles · Oct 7, 2019
Suspension
TL* THE CONTACT OWNS A 2013 RAM 3500. WHILE DRIVING 74 MPH, THE VEHICLE DROVE OVER A BUMP IN THE ROAD AND THE FRONT END VIBRATED VIOLENTLY. WHEN THE VEHICLE WAS STOPPED, THE FAILURE ALSO STOPPED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, BUT NO FAILURE WAS FOUND. THE VEHICLE WAS NOT REPAIRED. THE VEHICLE WAS NOT TAKEN TO…
Read full complaint
TL* THE CONTACT OWNS A 2013 RAM 3500. WHILE DRIVING 74 MPH, THE VEHICLE DROVE OVER A BUMP IN THE ROAD AND THE FRONT END VIBRATED VIOLENTLY. WHEN THE VEHICLE WAS STOPPED, THE FAILURE ALSO STOPPED. THE VEHICLE WAS TAKEN TO AN INDEPENDENT MECHANIC, BUT NO FAILURE WAS FOUND. THE VEHICLE WAS NOT REPAIRED. THE VEHICLE WAS NOT TAKEN TO A DEALER FOR DIAGNOSTIC TESTING OR REPAIRS. THE MANUFACTURER WAS NOT MADE AWARE OF THE FAILURE. THE FAILURE MILEAGE WAS 104,000.
NHTSA ODI #11266830
128,000 miles · Sep 11, 2019
Engine
I'VE HAD MULTIPLE RECALLS ON THIS VEHICLE, MY CHECK ENGINE LIGHT HAS BEEN GOING OFF CONTINUALLY, I'VE HAD THE WATER PUMP AND CATALYST CONVERTER REPLACED JUST TO NAME A FEW, WHICH TO MY LUCK MY TRUCK WAS STILL UNDER WARRANTY, NOW IT'S NOT. AGAIN THE CHECK ENGINE LIGHT GOES ON AND OFF RANDOMLY, TRY TO TAKE IT TO THE DEALER TO HAVE…
Read full complaint
I'VE HAD MULTIPLE RECALLS ON THIS VEHICLE, MY CHECK ENGINE LIGHT HAS BEEN GOING OFF CONTINUALLY, I'VE HAD THE WATER PUMP AND CATALYST CONVERTER REPLACED JUST TO NAME A FEW, WHICH TO MY LUCK MY TRUCK WAS STILL UNDER WARRANTY, NOW IT'S NOT. AGAIN THE CHECK ENGINE LIGHT GOES ON AND OFF RANDOMLY, TRY TO TAKE IT TO THE DEALER TO HAVE DIAGNOSED AND I'M TOLD THEY CAN DO NOTHING ABOUT IT UNTIL THE LIGHT COMES BACK ON, I FINALLY WAS ABLE TO GET IT TO THE DEALER WITH THE CHECK ENGINE LIGHT STILL ON AND NOW THIS TIME THERE WERE UP TO 5 ITEMS LISTED, THE ONE THAT CONCERNS ME IS THE ONE REGARDING THE TURBO ACTUATOR NOT COMMUNICATING. THE DEALER TOLD ME THAT I WOULD HAVE TO REPLACE IT, THIS IS GOING TO COST ME $3900 ALONE, MY TRUCK ONLY HAS A LITTLE OVER 120000 MILES ON IT, FOR THIS MANY THINGS TO BE GOING WRONG I AM STARTING TO THING I MIGHT HAVE BOUGHT A LEMON. I HAVE READ MULTIPLE PEOPLE IN FORUMS WHO HAVE HAD THE SAME ISSUE AS WELL AS ONE PERSON WHO ALSO SUBMITTED A COMPLAINT HERE ON YOUR WEBSITE. PLEASE LOOK INTO THIS AND HOPEFULLY THIS ITEM WILL BE ADDED TO THE MULTIPLE RECALLS THIS VEHICLE ALREADY HAS ON ITS RAP SHEET. THANK YOU FOR CONSIDERING MY COMPLAINT.
NHTSA ODI #11254812
75,000 miles · Jul 19, 2019
Power Train
MY SHIFT LEVER ON THE STEERING COLUMN WILL OFTEN NOT SHIFT ALL THE WAY BACK IN TO PARK WHEN TRYING TO PLACE THE VEHICLE IN PARK. OFTEN THE LEVER GETS HUNG UP BETWEEN REVERSE AND PARK. WHEN THIS HAPPENS, THE VEHICLE'S PRND INDICATOR ON THE CONTROL PANEL WILL TURN A YELLOW COLOR INSTEAD OF THE NORMAL WHITE COLOR. ALSO, THE SHIFT L…
Read full complaint
MY SHIFT LEVER ON THE STEERING COLUMN WILL OFTEN NOT SHIFT ALL THE WAY BACK IN TO PARK WHEN TRYING TO PLACE THE VEHICLE IN PARK. OFTEN THE LEVER GETS HUNG UP BETWEEN REVERSE AND PARK. WHEN THIS HAPPENS, THE VEHICLE'S PRND INDICATOR ON THE CONTROL PANEL WILL TURN A YELLOW COLOR INSTEAD OF THE NORMAL WHITE COLOR. ALSO, THE SHIFT LEVER WILL BECOME STUCK AND MUST BE FORCIBLY TAKEN BACK INTO GEAR TO TRY TO SHIFT AGAIN BACK INTO PARK. THE LEVER ACTS AS IF IT HAS FOUND A 'NEW' SLOT BETWEEN PARK AND REVERSE. ALSO, WHEN THIS YELLOW COLOR SHOWS ON MY PRND INDICATOR, IF I AM NEGLIGENT IN NOT GETTING THE VEHICLE FULLY BACK INTO PARK, THE VEHICLE WILL NOT START. I HAVE HAD TO HAVE THIS VEHICLE TOWED BACK TO THE DEALER REPAIR SHOP BECAUSE I COULD NOT GET THE SHIFT LEVER OUT OF THE SPOT IT WAS STUCK IN BETWEEN PARK AND REVERSE. THIS REPRESENTS A PROBLEM IN THAT I BELIEVE THE TRUCK IS RECOGNIZING THAT IT IS NEITHER IN PARK OR REVERSE SO THAT IT MAY BECOME A SAFETY ISSUE WHEN THE TRUCK IS PARKED. WITHOUT THE USE OF THE EMERGENCY BRAKE IT MAY ROLL OFF. THIS INCIDENT HAS SO FAR ONLY HAPPENED WHEN I STOP TO SHIFT THE VEHICLE INTO PARK AND ATTEMPT TO SHUT THE VEHICLE OFF. THE VEHICLE WILL SHUT OFF BUT WHEN I RETURN TO START THE VEHICLE, THE CONTROL PANEL EMITS THE SAME YELLOW COLORING FOR PRND INDICATOR AND WILL REFUSE TO START UNTIL THE SHIFT LEVER IS FORCED OUT OF THE SPACE IT HAS FOUND BETWEEN PARK AND REVERSE. I HAVEN'T YET TAKEN ANY PHOTOS, VIDEO OR BEEN ABLE TO GET THE DEALERSHIP REPAIR PERSONS TO ACKNOWLEDGE THE ISSUE. THE ONLY THING THE DEALERSHIP DID TO ADDRESS THE PROBLEM IS TALK ME INTO PURCHASING A NEW KEY FOB. *DT *DT *DT *DT *TR*JB *DT *DT THE CONSUMER STATED BTSI AND SHIFTER CABLE WAS REPLACED ON SEPTEMBER 13. *TR*DT*DT*JB
NHTSA ODI #11233405
21,000 miles · Jul 17, 2019
Vehicle Speed Control
TL* THE CONTACT OWNS A 2013 RAM 1500. WHILE DRIVING 70 MPH, THE VEHICLE BEGAN ACCELERATING ON ITS OWN AND WOULD NOT DECELERATE EVEN WHEN THE BRAKE PEDAL WAS DEPRESSED. THE CONTACT PLACED THE VEHICLE INTO NEUTRAL, BUT THE ENGINE CONTINUED TO REV. EVENTUALLY, THE VEHICLE BEGAN TO SLOW DOWN. WHEN THE CONTACT ATTEMPTED TO ACCELERATE…
Read full complaint
TL* THE CONTACT OWNS A 2013 RAM 1500. WHILE DRIVING 70 MPH, THE VEHICLE BEGAN ACCELERATING ON ITS OWN AND WOULD NOT DECELERATE EVEN WHEN THE BRAKE PEDAL WAS DEPRESSED. THE CONTACT PLACED THE VEHICLE INTO NEUTRAL, BUT THE ENGINE CONTINUED TO REV. EVENTUALLY, THE VEHICLE BEGAN TO SLOW DOWN. WHEN THE CONTACT ATTEMPTED TO ACCELERATE, THE ACCELERATOR PEDAL TRAVELED TO THE FLOORBOARD AND STALLED. THE FAILURE CONTINUED UNTIL THE CONTACT WAS ABLE TO COAST THE VEHICLE INTO AN ABANDONED PARKING LOT. CORTLAND CHRYSLER DODGE JEEP (3878 WEST RD, CORTLAND, NY 13045, (607) 218-7520) WAS CONTACTED AND STATED THAT THE FAILURE ALSO OCCURRED ON OTHER VEHICLES AND THAT THE ENGINE CONTROL MODULE NEEDED TO BE UPDATED. THE CONTACT WAS ABLE TO DRIVE THE VEHICLE HOME WITHOUT INCIDENT. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE FAILURE MILEAGE WAS 21,000. *DT*JB
NHTSA ODI #11232748
62,000 miles · Jul 14, 2019
Electrical SystemFire
THE ALTERNATOR CAUGHT ON FIRE. TRUCK HAS 62000 MILES ON IT. THE BATTERY LOW VOLTAGE CAME ON. AFTER THE TRUCK RAN FOR A MINUTE IT WENT OUT. I RAN THE TRUCK FOR TEN MINUTES. AFTER I PARKED THE TRUCK AND WENT INSIDE I COULD SMELL SOMETHING. WHEN I STEPPED OUT MY DOOR AND LOOKED SMOKE WAS ROLLING OUT FROM UNDER THE HOOD. I GRABB…
Read full complaint
THE ALTERNATOR CAUGHT ON FIRE. TRUCK HAS 62000 MILES ON IT. THE BATTERY LOW VOLTAGE CAME ON. AFTER THE TRUCK RAN FOR A MINUTE IT WENT OUT. I RAN THE TRUCK FOR TEN MINUTES. AFTER I PARKED THE TRUCK AND WENT INSIDE I COULD SMELL SOMETHING. WHEN I STEPPED OUT MY DOOR AND LOOKED SMOKE WAS ROLLING OUT FROM UNDER THE HOOD. I GRABBED THE EXTINGUISHER AND PUT IT OUT. I THEN SPRAYED IT DOWN WITH WATER TO COOL IT. IT TOOK SOME TIME.
NHTSA ODI #11231789
103,000 miles · Jun 10, 2019
WheelsFire
TL* THE CONTACT OWNS A 2013 RAM 3500. THE CONTACT STATED THAT WHILE DRIVING AT 55 MPH, THE VEHICLE ABS WARNING LIGHT ILLUMINATED AND THE VEHICLE VIOLENTLY SHAKES. THE CONTACT VEERED TO THE SHOULDER OF THE ROAD, GOT OUT THE VEHICLE AND SEEN SMOKE COMING FROM FRONT PASSENGER SIDE TIRE. THE CONTACT NOTICED THAT THE WHEEL WAS SEPARA…
Read full complaint
TL* THE CONTACT OWNS A 2013 RAM 3500. THE CONTACT STATED THAT WHILE DRIVING AT 55 MPH, THE VEHICLE ABS WARNING LIGHT ILLUMINATED AND THE VEHICLE VIOLENTLY SHAKES. THE CONTACT VEERED TO THE SHOULDER OF THE ROAD, GOT OUT THE VEHICLE AND SEEN SMOKE COMING FROM FRONT PASSENGER SIDE TIRE. THE CONTACT NOTICED THAT THE WHEEL WAS SEPARATED FROM THE AXLE. THERE WERE NO INJURIES SUSTAINED. NO POLICE/FIRE REPORT WAS FILED. THE CONTACT CONTACTED HIS INSURANCE TOWED THE VEHICLE TO THE DEALER RIVER OAKS CHRYSLER JEEP DODGE RAM 4807 KIRBY DR, HOUSTON, TX 77098 (888) 284-5254 WHERE A DIAGNOSTIC TESTING WAS PENDING. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE AND INFORMED THE CONTACT THAT NO RECALLS WERE UNDER THE VIN. THE FAILURE MILEAGE WAS 103,000.
NHTSA ODI #11218887
87,250 miles · May 23, 2019
Electrical SystemFire
I WENT TO START MY VEHICLE IN MY DRIVEWAY ON 5/23/2019. THE VEHICLE GAVE ME A LOW BATTERY INDICATION AND IMMEDIATELY SMELLED BURNING PLASTIC. SHUT THE VERTICLE OFF, HAD EVERYONE EXIT THE VEHICLE AND POPPED THE HOOD UP. SMOKE WAS POURING OUT OF THE ALTERNATOR THAT HAD BEEN "INSPECTED " INSTEAD OF BEING REPLACED ACCORDING TO TH…
Read full complaint
I WENT TO START MY VEHICLE IN MY DRIVEWAY ON 5/23/2019. THE VEHICLE GAVE ME A LOW BATTERY INDICATION AND IMMEDIATELY SMELLED BURNING PLASTIC. SHUT THE VERTICLE OFF, HAD EVERYONE EXIT THE VEHICLE AND POPPED THE HOOD UP. SMOKE WAS POURING OUT OF THE ALTERNATOR THAT HAD BEEN "INSPECTED " INSTEAD OF BEING REPLACED ACCORDING TO THE S68 RECALL BULLETIN 3MONTHS EARLIER. I QUICKLY GRABBED SOME TOOLS TO DISCONNECT BOTH BATTERIES TO PREVENT AND FURTHER DAMAGE OR FIRE. *DT*JB *DT *DT *TR
NHTSA ODI #11209603
Official recalls
16May 27, 2021
Chrysler (FCA US, LLC) is recalling certain 2012-2021 RAM 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles. Incorrect information in the Service and Owner's Manuals may cause the flanged lug nuts to be over-tightened, which could result in a broken wheel stud and possible wheel separation.
Consequence & remedy
Consequence: Wheel separation can cause a vehicle crash.
Remedy: Dealers will update the torque specification in the owner's manual and other published service documents. Dealers will also inspect the vehicle's wheel studs, replacing them if necessary, free of charge. Owner notification letters were mailed on November 30, 2021. Campaign Y36 owner notification letters were mailed on November 30, 2021. Campaign Y26 owner notification letters were mailed on December 1, 2021. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's numbers for this recall are Y26 and Y36.
May 9, 2019
Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 foot bed and a power locking tailgate. On August 29, 2019 Chrysler expanded the recall to include an additional 693,128 model year 2013-2014 Ram 1500, 2500 and 3500 pickup trucks. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence & remedy
Consequence: If the tailgate opens while the vehicle is being driven, cargo may fall out the vehicle and create a road hazard, increasing the risk of crash.
Remedy: Chrysler will notify owners, and dealers will repair the tailgate latch, free of charge. The recall began May 23, 2019. Chrysler is expected to notify owners of the expanded population on October 18, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's number for this recall is V44. Note: 2015-2017 MY Ram 1500 pickup trucks with truck beds other than 8 foot, are currently covered under NHTSA recall 18V-486 for this issue.
Jan 25, 2019
Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
Consequence & remedy
Consequence: A drag link separation can cause a loss of steering control, increasing the risk of crash.
Remedy: Chrysler will notify owners, and dealers will check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The recall began March 22, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V06.
Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Dec 20, 2017
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
Consequence & remedy
Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
Sep 12, 2017
Chrysler (FCA US LLC) is recalling certain 2013-2017 RAM 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, equipped with Cummins 6.7L Turbo Diesel engines that have Concentric-brand water pumps without a vent hole. These water pumps may leak coolant.
Consequence & remedy
Consequence: The leaking water pump can increase the risk of an engine compartment fire.
Remedy: Chrysler will notify owners, and dealers will replace the water pumps, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T51.
Aug 10, 2017
Streetcar ORV LLC, dba American Expedition Vehicles (AEV) is recalling certain 2013-2017 RAM 2500 and 3500 heavy duty trucks, modified by AEV to be equipped with cast aluminum Katla 8.5" road wheels. The outer surface of the wheel may fracture, resulting in rapid air loss.
Consequence & remedy
Consequence: If the wheel fractures, a loss of vehicle control can occur, increasing the risk of a crash.
Remedy: AEV will notify owners, and dealers will replace the wheels with wheels of similar value, free of charge. The recall began on August 30, 2017. Owners may contact AEV customer service at 1-248-926-0256 extension 500.
Oct 13, 2016
Chrysler (FCA US LLC) is recalling certain model year 2011-2014 Dodge Charger Police vehicles, 2007-2013 RAM 3500 Cab Chassis, 2008-2013 RAM 4500 and 5500 Cab Chassis, and 2013 RAM 2500 and 3500 vehicles. The affected vehicles have a 220 amp alternator that may suddenly fail.
Consequence & remedy
Consequence: If the alternator fails, the vehicle may stall without warning, increasing the risk of a crash. There is also the possibility that the alternator may short circuit, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the alternator with a revised alternator, free of charge. The recall began on December 23, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is S68.
Aug 26, 2015
Chrysler (FCA US LLC) is recalling certain model year 2014 Ram 2500 trucks and 2013-2014 Ram 3500 trucks and cab chassis manufactured October 9, 2012, to July 29, 2014. The affected vehicles may have inadequate welds securing the front track bar frame brackets, which may result in the bracket components separating from the frame.
Consequence & remedy
Consequence: If the bracket components separate from the frame, the vehicle may be more difficult to steer and control, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect and install a reinforcement bracket over the front track bar bracket. This recall began on February 24, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R46.
Jul 23, 2015
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, 3500, 4500, and 5500, 2015 Chrysler 200, Chrysler 300, Dodge Charger, and Dodge Challenger, 2014-2015 Jeep Grand Cherokee, Cherokee, and Dodge Durango, and 2013-2015 Dodge Viper vehicles. The affected vehicles are equipped with radios that have software vulnerabilities that can allow third-party access to certain networked vehicle control systems.
Consequence & remedy
Consequence: Exploitation of the software vulnerability may result in unauthorized remote modification and control of certain vehicle systems, increasing the risk of a crash.
Remedy: Chrysler will notify and mail affected owners a USB drive that includes a software update that eliminates the vulnerability, free of charge. Optionally, owners may download the update to their own USB drive from http://www.driveuconnect.com/software-update/ or take their vehicle to a Chrysler dealer for immediate installation. In an effort to mitigate the effects of this security vulnerability, Chrysler has had the wireless service provider close the open cellular connection to the vehicle that provided unauthorized access to the vehicle network. This measure may not have been implemented on all vehicles and does not address access by other means that will be remedied by the software update. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R40.
Jul 22, 2015
Chrysler (FCA US LLC) is recalling certain model year 2012-2014 Ram 1500, 2500, 3500, 4500, and 5500 trucks manufactured January 18, 2011, to October 7, 2014, and equipped with the Electronic Vehicle Information Center option. The affected vehicles have a steering wheel wiring harness that may rub against the driver air bag module retainer spring.
Consequence & remedy
Consequence: This abrasion may result in an electrical short that could cause driver's frontal air bag to unexpectedly deploy. Inadvertent deployment of the air bag may increase the risk of injury and the possibility of a vehicle crash.
Remedy: Chrysler will notify owners, and dealers will inspect, repair as necessary, and secure the steering wheel wiring harness. Additionally, protective caps will be added to the air bag retainer spring ends. These repairs will be done free of charge. The recall began on September 18, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R36.
Jul 22, 2015
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, and 3500 trucks manufactured June 20, 2012, to January 26, 2015. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence & remedy
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on September 8, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R23.
Additional source detail variants (2)
Seat Belts
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, and 3500 trucks manufactured June 20, 2012, to January 26, 2015. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on September 8, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R23.
Air Bags:side/window
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, and 3500 trucks manufactured June 20, 2012, to January 26, 2015. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on September 8, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R23.
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.
Consequence & remedy
Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.
Additional source detail variants (2)
Fuel System, Diesel
Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.
Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.
Engine And Engine Cooling:engine:diesel
Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.
Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.
Jun 4, 2013
Chrysler is recalling certain model year 2013 Ram 1500, 2500, and 3500 trucks manufactured September 9, 2012, through March 5, 2013 and equipped with optional premium tail lamps. In the affected vehicles, the turn signal indicator may not flash at a double rate to give a notification to the driver of a turn signal malfunction. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, reflective devices, and associated equipment."
Consequence & remedy
Consequence: Without a warning that the turn signal is malfunctioning, the driver would continue to use the vehicle, unaware that other drivers on the road are not being notified that the vehicle is turning, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will reprogram the Central Body Controller software, free of charge. The recall began June 27, 2013. Owners may contact Chrysler at 1-800-853-1403. Chrysler's recall campaign number is N35.
Jun 4, 2013
Chrysler is recalling certain model year 2013 Ram 2500 and 3500 trucks manufactured January 7, 2013, through February 28, 2013 and equipped with optional premium headlamps. The headlamp shutters may function improperly when in high-beam mode. Thus, these vehicles fail to conform to the requirements of Federal Motor Vehicle Safety Standard (FMVSS) No. 108, "Lamps, reflective devices, and associated equipment."
Consequence & remedy
Consequence: Improper headlight shutter function during high beam use may reduce the drivers visibility and possibly blind oncoming traffic. Either condition may increase the risk of crash.
Remedy: Chrysler will notify owners, and dealers will reconfigure the Central Body Controller, free of charge. The recall began July 30, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N33.
Apr 3, 2013
Chrysler Group LLC (Chrysler) is recalling certain model year 2013 Dodge Ram 2500 and 3500 trucks manufactured January 7, 2013, through March 6, 2013. The engine cover may trap an excessive amount of heat under the cover.
Consequence & remedy
Consequence: The excessive heat under the engine cover may result in an under hood fire.
Remedy: Chrysler will notify owners, and dealers will replace the existing engine cover with one that is a different design, free of charge. An interim letter was mailed on May 31, 2013. A second letter was mailed to owners with instructions on how to obtain the free remedy on August 15, 2013. Owners may contact Chrysler at 1-800-853-1403. Chrysler's recall campaign number is N19.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3RQ25003 · Post Recall Remedy Brake Transmission Shift Interlock (btsi) Failure
Opened Jul 3, 2025 · No close date supplied
Status: open (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:gear Position Indication (prndl)
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Power Train:automatic Transmission:gear Position Indication (prndl)
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
PE18016 · Steering Loss Due To Linkage Separation
Opened Dec 17, 2018 · Closed Dec 12, 2019
Status: closed (inferred from source dates) · Steering:linkages:drag:link:connection
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 18-016 to investigate the steering system on model year (MY) 2015 and 2016 Ram 2500 manufactured by FCA US, LLC (FCA). Four complaints were received alleging separation of the drag link, a steering linkage that connects between the right front steering knuckle and the pitman arm on the steering box output shaft. The failures were found to be at a threaded coupler within the drag link used for adjusting the length of the linkage during routine maintenance (alignment) of the steering system.Once separation occurs, turning the steering wheel has no effect, and there is no way for the driver to control or maintain the direction of the vehicle. During the investigation, it was determined that the same threaded coupler was used on two different drag link designs FCA manufactured on MY 2013-2018 Ram 2500 and 3500 pickups. FCA refers to the designs as either 4x2 or 4x4 style. In both designs, the coupler is prevented from turning on the drag link via two jam nuts that are tightened against the coupler. In its response to NHTSA's March 15, 2019, Information Request (IR) letter, FCA identified 48 incidents alleging separation of the steering linkage at the coupler resulting in a loss of steering control. Of those, 13 involved a crash, one of which resulted in an injury. All of the separations involved the 4x4 style drag link. Additionally, FCA's IR response refers to over 300 4x4 style equipped vehicles that experienced, or may have experienced loosening of one or more coupler jam nuts. On January 25, 2019, FCA submitted a Defect Information Report (DIR) initiating NHTSA Recall No. 19V-021. In its DIR, FCA stated that the outboard jam nut in certain MY 2013-2018 Ram 2500 and 3500 could loosen potentially resulting in damage to the coupler and/or drag link threading allowing one end of the drag link to separate. The DIR notes that drag link separation results in loss of steering control, which in turn can cause a crash without warning. FCA's DIR did not identify a root cause for the defect, however it posits that an improperly torqued outboard jam nut could loosen, and with long-term vehicle use, cause damage to the outer link bar and/or coupler threads due to relative motion between the two components. The scope of Recall 19V-021 included vehicles with the 4x4 style drag link only. Also discussed in its IR response, FCA noted that the 4x2 style drag link contains a design difference (the outboard portion of the drag link is straight while the 4x4 style contains a bend) which it suggests may result in differences in the mechanical (bending) loads presented at the coupler and jam nut interface. Moreover, the DIR states that While root cause of the 4x4 style defect has not been established, FCA US believes that bending loads on the drag link is, at least, a causal contributing factor. FCA notes it did not identify any reports alleging 4x2 style separation as well as only three reports of loosening of jam nuts, two of which resulted in loosening that provided obvious warning to the vehicle operator, indicating a different failure mode.NHTSA is upgrading this investigation to Engineering Analysis (EA) 19-004 in order to continue to monitor the subject 4x2 style vehicles for evidence of field failures. Additionally, in conjunction with NHTSA's Vehicle Research and Test Center, ODI intends to more thoroughly study potential root cause(s) of the 4x4 style defect mechanism, and if identified, will seek to determine if the 4x2 drag link is susceptible to the same mechanism(s). NHTSA will also evaluate the long-term suitability of the recall
RQ15004 · Software Security Vulnerability
Opened Jul 24, 2015 · Closed Jan 5, 2016
Status: closed (inferred from source dates) · Electrical System:software
On July 23, 2015, Fiat Chrysler Automobiles (FCA) launched Safety Recall 15V-461 to remedy security vulnerabilities in approximately 1.4 million model year (MY) 2013 through 2015 vehicles equipped with Uconnect head units (HU) 8.4A (RA3 radio) and 8.4AN (RA4 radio) manufactured by Harman International.On July 24, 2015, the Office of Defects Investigation (ODI) opened Recall Query, RQ 15-004, to investigate HU security vulnerabilities and remedy effectiveness in the recalled population and to determine whether similar units have been supplied for use in other FCA vehicles.In an August 11, 2015 letter, FCA submitted a second Part 573 safety recall report expanding the scope of the Uconnect RA4 model radio to include additional 7,810 MY 2015 Jeep Renegade vehicles manufactured from September 18, 2014 through June 25, 2015 (Recall 15V-508).Scope analysis indicated that Uconnect radios installed in FCA vehicles not included in recalls 15V-461 or 15V-508 (subject recalls) are not equipped with built-in cellular access or short range wireless communication features and, thus, do not contain the security vulnerabilities addressed by the subject recalls. SUBJECT VEHICLES: MY2014 through 2015 Dodge Durango, Jeep Grand Cherokee and Jeep Cherokee sport utility vehicles; MY2013 through 2015 Ram 1500, 2500, 3500 and 4500/5500 pickup trucks; MY2013 through 2015 Dodge Viper vehicles; and MY2015 Chrysler 200, 300, Jeep Renegade, Dodge Charger and Challenger vehicles.According to FCA, long and short range wireless vulnerabilities identified in the recalled vehicles could allow unauthorized third-party access to, and manipulation of, networked vehicle control systems.Successful exploitation of the vulnerabilities, coupled with reverse engineering of networked microprocessor control modules, could result in unauthorized manipulation of vehicle control systems. This unauthorized manipulation of vehicle controls and systems could expose the driver, vehicle occupants or other highway users to an increased risk of injury.FCA and its network provider, Sprint, conducted a nationwide campaign to block access to a radio communications port that was unintentionally left open.On July 27, 2015, short range wireless vulnerabilities were also blocked.Finally, third party security evaluation and regression testing identified vulnerabilities that were either remedied by Sprint or through updates to the FCA Uconnect software.ODI identified a total of 30 complaints or field reports on unique vehicles submitted by FCA (29) or received by NHTSA (1) alleging incidents of theft from a vehicle or anomalous performance that the owner alleged were caused by, or may have been caused by, remote hacking.Twenty-six (87%) of these reports were submitted after a magazine article was published on July 21, 2015, describing the remote hacking of an FCA vehicle by researchers who were able to affect the operation of various vehicle control systems, including the service brakes, steering, throttle and ignition.Most of the complaints involved vehicle systems that were not safety critical (e.g., complaints related to radio, navigation system, or air-conditioning control) and did not affect vehicle control.Three complaints reported engine stalls.One owner reported sudden unintended acceleration allegedly related to hacking.None of the complaints or field reports reviewed involved the steering and braking vehicle control effects demonstrated by the research hackers prior to the recall.There were no confirmed incidents of hacking in any of the records reviewed by ODI.The remedies completed by Sprint and FCA appear to have eliminated vulnerabilities that mi
Illustration