NHTSA owner reports · September 18, 2026 snapshot.
Power Train complaints
62 reportsClear category filter76,200 miles · May 7, 2018
Power Train
WHEN 4X4 SERVICE IS REQUIRED THE TRUCKS DRIVE SYSTEM WILL RATTLE VERY LOUD FORCING THE TRUCK TO COME TO A COMPLETE STOP. THE TRUCK MUST BE SHUT OFF AND RESTARTED THIS WILL HAPPEN EVERY 1000 MILES UNTIL SERVICE IS PERFORMED. THIS HAPPENED ABOUT 4000 MILES BEFORE MY 60,000 MILE SERVICE ON THE INTERSTATE PULLING A FIFTH WHEEL AND…
Read full complaint
WHEN 4X4 SERVICE IS REQUIRED THE TRUCKS DRIVE SYSTEM WILL RATTLE VERY LOUD FORCING THE TRUCK TO COME TO A COMPLETE STOP. THE TRUCK MUST BE SHUT OFF AND RESTARTED THIS WILL HAPPEN EVERY 1000 MILES UNTIL SERVICE IS PERFORMED. THIS HAPPENED ABOUT 4000 MILES BEFORE MY 60,000 MILE SERVICE ON THE INTERSTATE PULLING A FIFTH WHEEL AND THEN AGAIN 3000 MILES BEFORE REQUIRED SERVICE. THIS HAPPENED AGAIN AT 76,000 MILES ON THE INTERSTATE SINGLE LANE NO SHOULDER IN THE MOUNTAINS OF UTAH. THIS IS VERY DANGEROUS. I GET A REMINDER MESSAGE FOR REQUIRED SERVICE, BUT THE 4X4 SERVICE REMINDER IS UNACCEPTABLE.
NHTSA ODI #11092182
47,968 miles · May 3, 2018
Power Train
TL* THE CONTACT OWNS A 2014 RAM 2500. THE CONTACT STATED THAT THE GEAR SHIFTER WAS ABLE TO MOVE WITHOUT THE KEY BEING INSERTED IN THE IGNITION OR THE BRAKE PEDAL BEING DEPRESSED. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 17V821000 (POWER TRAIN); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT …
Read full complaint
TL* THE CONTACT OWNS A 2014 RAM 2500. THE CONTACT STATED THAT THE GEAR SHIFTER WAS ABLE TO MOVE WITHOUT THE KEY BEING INSERTED IN THE IGNITION OR THE BRAKE PEDAL BEING DEPRESSED. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 17V821000 (POWER TRAIN); HOWEVER, THE PARTS TO DO THE REPAIR WERE UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. CARL BURGER CHRYSLER JEEP DODGE RAM (8355 HERCULES ST, LA MESA, CA) WAS CONTACTED AND CONFIRMED THAT THE PARTS WERE NOT AVAILABLE FOR THE RECALL REMEDY. THE MANUFACTURER WAS NOTIFIED AND DID NOT KNOW WHEN THE PARTS WERE TO BECOME AVAILABLE. THE VEHICLE WAS NOT DIAGNOSED OR REPAIRED. THE FAILURE MILEAGE WAS 47,968. PARTS DISTRIBUTION DISCONNECT.
NHTSA ODI #11091552
Mileage unknown · Apr 2, 2018
EngineEngine And Engine CoolingPower Train
TL* THE CONTACT OWNS A 2014 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBERS: 17V562000 (ENGINE AND ENGINE COOLING) AND 17V821000 (POWER TRAIN). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIRS. THE CONTACT CALLED COLORADO SPRINGS DODGE AT 719-428-6400 (LOC…
Read full complaint
TL* THE CONTACT OWNS A 2014 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBERS: 17V562000 (ENGINE AND ENGINE COOLING) AND 17V821000 (POWER TRAIN). THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIRS. THE CONTACT CALLED COLORADO SPRINGS DODGE AT 719-428-6400 (LOCATED AT 7455 AUSTIN BLUFFS PKWY, COLORADO SPRINGS, CO 80923) AND WAS INFORMED THAT THE PARTS WERE NOT AVAILABLE. THE MANUFACTURER WAS MADE AWARE OF THE ISSUE AND WAS NOT ABLE TO CONFIRM WHEN THE PARTS WERE TO BECOME AVAILABLE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.
NHTSA ODI #11082565
92,000 miles · Mar 19, 2018
Power TrainCrash
TL* THE CONTACT OWNS A 2014 RAM 2500. WHILE THE VEHICLE WAS STATIONARY AND UNOCCUPIED, IT ROLLED BACKWARDS OUT OF THE PARK POSITION AND CRASHED INTO SOME TREES. THE AIR BAGS DID NOT DEPLOY. A POLICE REPORT WAS NOT FILED. THERE WERE NO INJURIES SUSTAINED. EGOLF CHRYSLER JEEP DODGE RAM IN BREVARD, NORTH CAROLINA WAS MADE AWARE OF …
Read full complaint
TL* THE CONTACT OWNS A 2014 RAM 2500. WHILE THE VEHICLE WAS STATIONARY AND UNOCCUPIED, IT ROLLED BACKWARDS OUT OF THE PARK POSITION AND CRASHED INTO SOME TREES. THE AIR BAGS DID NOT DEPLOY. A POLICE REPORT WAS NOT FILED. THERE WERE NO INJURIES SUSTAINED. EGOLF CHRYSLER JEEP DODGE RAM IN BREVARD, NORTH CAROLINA WAS MADE AWARE OF THE FAILURE. THE VEHICLE WAS NOT REPAIRED. THE MANUFACTURER WAS MADE AWARE OF THE FAILURE. THE VIN WAS INCLUDED IN NHTSA CAMPAIGN NUMBER: 17V821000 (POWER TRAIN), WHICH WAS DIRECTLY RELATED TO THE FAILURE; HOWEVER, THERE WAS NO REMEDY. THE FAILURE MILEAGE WAS 92,000.
NHTSA ODI #11080234
Mileage unknown · Feb 22, 2018
Power Train
TL* THE CONTACT OWNS A 2014 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 17V821000 (POWER TRAIN); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. FRANKLIN CHRYSLER DODGE JEEP RAM IN FRANKLIN, TENNESS…
Read full complaint
TL* THE CONTACT OWNS A 2014 RAM 2500. THE CONTACT RECEIVED NOTIFICATION OF NHTSA CAMPAIGN NUMBER: 17V821000 (POWER TRAIN); HOWEVER, THE PART TO DO THE REPAIR WAS UNAVAILABLE. THE CONTACT STATED THAT THE MANUFACTURER EXCEEDED A REASONABLE AMOUNT OF TIME FOR THE RECALL REPAIR. FRANKLIN CHRYSLER DODGE JEEP RAM IN FRANKLIN, TENNESSEE WAS MADE AWARE OF THE RECALL AND STATED THAT THE PARTS WERE UNAVAILABLE. THE MANUFACTURER WAS NOT MADE AWARE OF THE ISSUE. THE CONTACT HAD NOT EXPERIENCED A FAILURE. PARTS DISTRIBUTION DISCONNECT.
NHTSA ODI #11074317
30,000 miles · Feb 14, 2018
Power Train
WHEN DRIVING ON THE ROAD AND YOU LET OFF THE GAS PEDAL, THEN YOU NEED TO ACCELERATE TO GET OUT OF THE WAY OF SOMEONE OR TO AVOID A NEAR ACCIDENT, YOU PRESS THE GAS PEDAL ALL THE WAY DOWN AND THERE IS A COUPLE SECOND DELAY TO A FEW SECONDS, A LAG, BEFORE THE TRUCK APPEARS TO RECEIVE THE COMMAND TO HURRY UP AND GO. IT HAS CAUSED …
Read full complaint
WHEN DRIVING ON THE ROAD AND YOU LET OFF THE GAS PEDAL, THEN YOU NEED TO ACCELERATE TO GET OUT OF THE WAY OF SOMEONE OR TO AVOID A NEAR ACCIDENT, YOU PRESS THE GAS PEDAL ALL THE WAY DOWN AND THERE IS A COUPLE SECOND DELAY TO A FEW SECONDS, A LAG, BEFORE THE TRUCK APPEARS TO RECEIVE THE COMMAND TO HURRY UP AND GO. IT HAS CAUSED ME TO ALMOST BE REAR ENDED AND BE IN AN ACCIDENT WITH MY WIFE AND DAUGHTER IN MY TRUCK.
NHTSA ODI #11072967
65,500 miles · Jan 29, 2018
Power Train
TL* THE CONTACT OWNS A 2014 RAM 2500. WHILE THE VEHICLE WAS PARKED, IT SHIFTED INTO NEUTRAL BY ITSELF. THERE WERE NO WARNING INDICATORS ILLUMINATED PRIOR TO THE FAILURE. THE VEHICLE WAS TAKEN TO THE DEALER (CRONIC CHRYSLER DODGE JEEP RAM, 2515 N EXPRESSWAY, GRIFFIN, GA 30223) WHERE IT WAS DIAGNOSED THAT THE GEAR SHIFT WAS DEFECT…
Read full complaint
TL* THE CONTACT OWNS A 2014 RAM 2500. WHILE THE VEHICLE WAS PARKED, IT SHIFTED INTO NEUTRAL BY ITSELF. THERE WERE NO WARNING INDICATORS ILLUMINATED PRIOR TO THE FAILURE. THE VEHICLE WAS TAKEN TO THE DEALER (CRONIC CHRYSLER DODGE JEEP RAM, 2515 N EXPRESSWAY, GRIFFIN, GA 30223) WHERE IT WAS DIAGNOSED THAT THE GEAR SHIFT WAS DEFECTIVE. THE VEHICLE WAS REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE. THE VIN WAS UNKNOWN. THE FAILURE MILEAGE WAS 65,500.
NHTSA ODI #11065694
48,000 miles · Jan 24, 2018
Power Train
WHEN PULLING A TRAVEL TRAILER GOING UP OR DOWN A STEEP GRADE WITH THE VEHICLE IN TOW HALL THE TRANSMISSION WILL HANG UP IN ANY GIVEN GEAR FORCING YOU TO APPLY THE BREAK AND SHIFT THE VEHICLE INTO NEUTRAL THEN BACK INTO DRIVE THIS HAS BEEN REPORTED TO LONE STAR DOGE 1309 S. PACIFIC MINEOLA TX. THE DEALERSHIP SAID NO CODES WERE …
Read full complaint
WHEN PULLING A TRAVEL TRAILER GOING UP OR DOWN A STEEP GRADE WITH THE VEHICLE IN TOW HALL THE TRANSMISSION WILL HANG UP IN ANY GIVEN GEAR FORCING YOU TO APPLY THE BREAK AND SHIFT THE VEHICLE INTO NEUTRAL THEN BACK INTO DRIVE THIS HAS BEEN REPORTED TO LONE STAR DOGE 1309 S. PACIFIC MINEOLA TX. THE DEALERSHIP SAID NO CODES WERE FOUND SO NOTHING WAS WRONG. I HAVE HAD THIS HAPPEN SEVERAL TIMES AND AM WORRIED ABOUT DRIVING THE TRUCK NOW. I HAVE TAKEN THE TRUCK INTO THE DEALER MULTIPLE TIMES FOR THIS ISSUE AND IT STILL HAS NOT BEEN REPAIRED. I TAKE IT IN ONE TIME AND THEY TELL ME IT IS FIXED AFTER THEY WORK ON IT IT IS NOT FIXED AND I TAKE IT IN AGAIN AND THEY SAY IT IS THE EGR VALVE SO I HAVE THAT FIXED AND IT IS STILL DOING THE SAME THING SO I BRING IT IN AGAIN AND THEY SAY IT IS SOMETHING ELSE AND I WOULD NEED TO PAY FOR REPAIRS AGAIN. THIS SHOULD HAVE BEEN COVERED UNDER THE WARRANTY BUT THEY SAY THIS NEEDS TO BE FIXED FIRST BEFORE THE WARRANTY WORK CAN BE DONE WHY CANT THEY JUST FIX THE WARRANTY WORK INSTEAD OF FIND THINGS THAT "HAVE TO BE FIXED BEFORE THAT WORK CAN BE DONE" WITH NO RELATION TO THE TRANSMISSSION.
NHTSA ODI #11064705
64,000 miles · Jan 24, 2018
Power Train
I HAVE HAD SEVERAL INCIDENTS THIS YEAR OF THE TRANSMISSION LEVER BEING STUCK IN PARK. THIS IS WITH ENGINE ON, BRAKE PEDAL DEPRESSED, AND EMERGENCY BRAKE RELEASED. YOU COULD NOT MOVE THE LEVER AT ALL YOU WERE STUCK, AFTER 30-60 SEC, AND REPEATED ATTEMPTS TO MOVE THE LEVER, IT EVENTUALLY MOVED TO DRIVE. THIS WAS REPORTED TO THE L…
Read full complaint
I HAVE HAD SEVERAL INCIDENTS THIS YEAR OF THE TRANSMISSION LEVER BEING STUCK IN PARK. THIS IS WITH ENGINE ON, BRAKE PEDAL DEPRESSED, AND EMERGENCY BRAKE RELEASED. YOU COULD NOT MOVE THE LEVER AT ALL YOU WERE STUCK, AFTER 30-60 SEC, AND REPEATED ATTEMPTS TO MOVE THE LEVER, IT EVENTUALLY MOVED TO DRIVE. THIS WAS REPORTED TO THE LOCAL DODGE RAM DEALER LONE STAR DOGE 1309 S. PACIFIC ST. IN MINEOLIA TX THIS YEAR, WHO CLAIMS NOT TO BE ABLE TO REPRODUCE THE PROBLEM. NO PAPERWORK WAS EVEN WRITTEN UP ON THE INCIDENT.
NHTSA ODI #11064688
55,710 miles · Aug 10, 2017
Power Train
TL* THE CONTACT OWNS A 2014 RAM 2500. THE CONTACT STATED THAT WHILE THE VEHICLE WAS PARKED AT A PARKING LOT, THE GEAR LEVER SHIFTED OUT OF PARK INDEPENDENTLY WITHOUT WARNING. THE CONTACT WAS ABLE TO STOP THE VEHICLE ONCE IT BEGAN TO ROLL THREE FEET. THE VEHICLE WAS TAKEN TO AUTONATION DODGE DEALER, LOCATED AT 1011 CHATHAM CENTER…
Read full complaint
TL* THE CONTACT OWNS A 2014 RAM 2500. THE CONTACT STATED THAT WHILE THE VEHICLE WAS PARKED AT A PARKING LOT, THE GEAR LEVER SHIFTED OUT OF PARK INDEPENDENTLY WITHOUT WARNING. THE CONTACT WAS ABLE TO STOP THE VEHICLE ONCE IT BEGAN TO ROLL THREE FEET. THE VEHICLE WAS TAKEN TO AUTONATION DODGE DEALER, LOCATED AT 1011 CHATHAM CENTER DRIVE, SAVANNAH, GA 31405, WHERE IT WAS DIAGNOSED THAT THE GEAR LEVER ELECTRICAL MODULE FAILED AND NEEDED TO BE REPLACED. THE VEHICLE WAS IN THE PROCESS OF BEING REPAIRED. THE MANUFACTURER WAS NOTIFIED OF THE FAILURE AND INFORMED THAT THE VEHICLE WAS NOT COVERED UNDER THE POWER TRAIN WARRANTY AND THEY WILL NOT REPAIR THE VEHICLE. THE APPROXIMATE FAILURE MILEAGE WAS 55,710.
NHTSA ODI #11014191
Official recalls
14May 9, 2019
Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 foot bed and a power locking tailgate. On August 29, 2019 Chrysler expanded the recall to include an additional 693,128 model year 2013-2014 Ram 1500, 2500 and 3500 pickup trucks. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence & remedy
Consequence: If the tailgate opens while the vehicle is being driven, cargo may fall out the vehicle and create a road hazard, increasing the risk of crash.
Remedy: Chrysler will notify owners, and dealers will repair the tailgate latch, free of charge. The recall began May 23, 2019. Chrysler is expected to notify owners of the expanded population on October 18, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's number for this recall is V44. Note: 2015-2017 MY Ram 1500 pickup trucks with truck beds other than 8 foot, are currently covered under NHTSA recall 18V-486 for this issue.
Jan 25, 2019
Chrysler (FCA US LLC) is recalling certain 2013-2018 Ram 3500 and 2014-2018 Ram 3500 Chassis Cab and Ram 2500 vehicles. The outboard steering linkage jam nut may loosen, allowing one end of the drag link to separate.
Consequence & remedy
Consequence: A drag link separation can cause a loss of steering control, increasing the risk of crash.
Remedy: Chrysler will notify owners, and dealers will check the steering linkage jam nut tightness, replacing the drag link assembly or welding the nut to the adjuster sleeve, free of charge. The recall began March 22, 2019. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is V06.
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Dec 21, 2017
Chrysler (FCA US LLC) is recalling various Dodge, Chrysler, and RAM vehicles equipped with Kidde Plastic-Handle or Push Button 'Pindicator' Fire Extinguishers. A list of the affected trailer models is available at: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17V824-0103.pdf. These extinguishers may become clogged, preventing the extinguisher from discharging as expected or requiring excessive force to activate the extinguisher. Additionally, in certain models, the nozzle may detach from the valve assembly with enough force that it could cause injury and also render the product inoperable. For a full list of the affected fire extinguisher models visit: https://static.nhtsa.gov/odi/rcl/2017/RMISC-17E062-5427.pdf
Consequence & remedy
Consequence: If the fire extinguisher does not function properly, it can increase the risk of injury in the event of a fire.
Remedy: Chrysler will notify owners instructing them to contact Kidde for a replacement fire extinguisher, free of charge. The recall began February 14, 2018. Owners may contact Chrysler customer service at 1-800-853-1403 or Kidde customer service service toll-free at 1-855-262-3540, or online at www.kidde.com and click on "Product Safety Recall" for more information. Chrysler's number for this recall is T82.
Dec 20, 2017
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
Consequence & remedy
Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
Sep 12, 2017
Chrysler (FCA US LLC) is recalling certain 2013-2017 RAM 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, equipped with Cummins 6.7L Turbo Diesel engines that have Concentric-brand water pumps without a vent hole. These water pumps may leak coolant.
Consequence & remedy
Consequence: The leaking water pump can increase the risk of an engine compartment fire.
Remedy: Chrysler will notify owners, and dealers will replace the water pumps, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T51.
Aug 10, 2017
Streetcar ORV LLC, dba American Expedition Vehicles (AEV) is recalling certain 2013-2017 RAM 2500 and 3500 heavy duty trucks, modified by AEV to be equipped with cast aluminum Katla 8.5" road wheels. The outer surface of the wheel may fracture, resulting in rapid air loss.
Consequence & remedy
Consequence: If the wheel fractures, a loss of vehicle control can occur, increasing the risk of a crash.
Remedy: AEV will notify owners, and dealers will replace the wheels with wheels of similar value, free of charge. The recall began on August 30, 2017. Owners may contact AEV customer service at 1-248-926-0256 extension 500.
May 9, 2017
Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag and the seat belt pretensioner will be disabled from deploying.
Consequence & remedy
Consequence: If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.
Remedy: Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.
Additional source detail variants (2)
Air Bags:side/window:curtain
Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag and the seat belt pretensioner will be disabled from deploying.
Consequence: If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.
Remedy: Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.
Air Bags
Chrysler (FCA US LLC) is recalling certain model year 2013-2016 Ram 1500, Ram 2500, and 2014-2016 Ram 3500 vehicles. Certain driving conditions, such as driving off-road or debris striking the vehicle may cause the roll rate sensor to trigger a fault within the Occupant Restraint Controller (ORC). If this fault occurs, the rollover side curtain air bag and the seat belt pretensioner will be disabled from deploying.
Consequence: If the rollover side curtain air bags and seat belt pretensioners are disabled, there is an increased risk of injury to the vehicle occupants in the event of a crash that necessitates activation of these safety systems.
Remedy: Chrysler will notify owners, and dealers will update the ORC software, free of charge. The recall began June 26, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T25.
Aug 26, 2015
Chrysler (FCA US LLC) is recalling certain model year 2014 Ram 2500 trucks and 2013-2014 Ram 3500 trucks and cab chassis manufactured October 9, 2012, to July 29, 2014. The affected vehicles may have inadequate welds securing the front track bar frame brackets, which may result in the bracket components separating from the frame.
Consequence & remedy
Consequence: If the bracket components separate from the frame, the vehicle may be more difficult to steer and control, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect and install a reinforcement bracket over the front track bar bracket. This recall began on February 24, 2016. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R46.
Jul 23, 2015
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, 3500, 4500, and 5500, 2015 Chrysler 200, Chrysler 300, Dodge Charger, and Dodge Challenger, 2014-2015 Jeep Grand Cherokee, Cherokee, and Dodge Durango, and 2013-2015 Dodge Viper vehicles. The affected vehicles are equipped with radios that have software vulnerabilities that can allow third-party access to certain networked vehicle control systems.
Consequence & remedy
Consequence: Exploitation of the software vulnerability may result in unauthorized remote modification and control of certain vehicle systems, increasing the risk of a crash.
Remedy: Chrysler will notify and mail affected owners a USB drive that includes a software update that eliminates the vulnerability, free of charge. Optionally, owners may download the update to their own USB drive from http://www.driveuconnect.com/software-update/ or take their vehicle to a Chrysler dealer for immediate installation. In an effort to mitigate the effects of this security vulnerability, Chrysler has had the wireless service provider close the open cellular connection to the vehicle that provided unauthorized access to the vehicle network. This measure may not have been implemented on all vehicles and does not address access by other means that will be remedied by the software update. The recall began on August 25, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R40.
Jul 22, 2015
Chrysler (FCA US LLC) is recalling certain model year 2012-2014 Ram 1500, 2500, 3500, 4500, and 5500 trucks manufactured January 18, 2011, to October 7, 2014, and equipped with the Electronic Vehicle Information Center option. The affected vehicles have a steering wheel wiring harness that may rub against the driver air bag module retainer spring.
Consequence & remedy
Consequence: This abrasion may result in an electrical short that could cause driver's frontal air bag to unexpectedly deploy. Inadvertent deployment of the air bag may increase the risk of injury and the possibility of a vehicle crash.
Remedy: Chrysler will notify owners, and dealers will inspect, repair as necessary, and secure the steering wheel wiring harness. Additionally, protective caps will be added to the air bag retainer spring ends. These repairs will be done free of charge. The recall began on September 18, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R36.
Jul 22, 2015
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, and 3500 trucks manufactured June 20, 2012, to January 26, 2015. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence & remedy
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on September 8, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R23.
Additional source detail variants (2)
Seat Belts
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, and 3500 trucks manufactured June 20, 2012, to January 26, 2015. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on September 8, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R23.
Air Bags:side/window
Chrysler (FCA US LLC) is recalling certain model year 2013-2015 Ram 1500, 2500, and 3500 trucks manufactured June 20, 2012, to January 26, 2015. In the affected vehicles, the side impact sensor calibrations may be overly sensitive, and as a result, the side air bag inflatable curtains and seat air bags may unexpectedly deploy and the seat belt pre-tensioners may activate.
Consequence: Air bags that unexpectedly deploy increase the risk of a crash or injury.
Remedy: Chrysler will notify owners, and dealers will update the Occupant Restraint Control module calibration, free of charge. The recall began on September 8, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is R23.
Oct 8, 2014
Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.
Consequence & remedy
Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.
Additional source detail variants (2)
Fuel System, Diesel
Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.
Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.
Engine And Engine Cooling:engine:diesel
Chrysler Group LLC (Chrysler) is recalling certain model year 2010-2014 Ram 2500, 3500, 4500, and 5500 trucks manufactured March 27, 2009, to September 5, 2013. In the affected vehicles, the electrical connectors of the diesel fuel heater may overheat.
Consequence: If the connectors overheat, the fuel heater may leak fuel, increasing the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the harness side connector with a silver plated beryllium copper terminal service kit, and inspect the fuel heater for leaks, replacing it as necessary, free of charge. Chrysler issued interim notification to owners on December 8, 2014. The recall began on April 27, 2015. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is P65.
Oct 17, 2013
Chrysler Group LLC (Chrysler) is recalling certain model year 2014 RAM 1500, 2500, and 3500 trucks manufactured July 1, 2013, through August 22, 2013. Randomly, the warning lights in the instrument cluster may fail to illuminate as designed.
Consequence & remedy
Consequence: Inoperative warning lights may not properly warn the driver of vehicle problems, increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will update the instrument cluster software, free of charge. The recall began on November 25, 2013. Owners may contact Chrysler at 1-800-247-9753. Chrysler's recall campaign number is N59.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
4RQ25003 · Post Recall Remedy Brake Transmission Shift Interlock (btsi) Failure
Opened Jul 3, 2025 · No close date supplied
Status: open (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:gear Position Indication (prndl)
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Power Train:automatic Transmission:gear Position Indication (prndl)
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
EA19004 · Steering Loss Due To Linkage Separation
Opened Dec 1, 2019 · Closed Nov 20, 2025
Status: closed (inferred from source dates) · Steering:linkages:drag:link:connection
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation PE18016 to investigate alleged drag link failures in the steering system on model year (MY) 2015 and 2016 Ram 2500 trucks manufactured by FCA US, LLC (FCA). The drag link failures were found to be due to a safety defect with the steering linkage where the drag link adjustable connector (used to adjust the steering system), held in position by two opposing jam nuts, can loosen. The loosening of this part can lead to wear and deterioration of the threads and eventual separation of the drag link, causing loss of steering. During the course of PE18016, it was found that two styles of drag link were used by FCA on the subject vehicles. The subject vehicles consist of two drivetrain types including four-wheel drive (4WD) and two-wheel drive (2WD). The 4WD and 2WD trucks used drag links of differing design but both incorporated the same threaded connector. In January 2019 FCA issued recall 19V-021 to address a potential loss of steering control in certain Model Year (MY) 2013-2018 4WD RAM 2500 and 3500 trucks. The trucks using the 2WD style drag link were not included in the scope of recall 19V-021. ODI upgraded PE18016 to an Engineering Analysis EA19004 on December 12, 2019. The purpose of EA19004 was to investigate if the root cause of the safety defect addressed by recall 19V-201 also affected the 2WD trucks and evaluate FCA’s rationale for not including them. ODI also monitored incoming consumer complaints regarding the remedy associated with 19V-021 and evaluated the suitability and long-term effectiveness of the prescribed repair. In the Defect Information Report submitted for recall 19V-021, FCA stated that the outboard jam nut could loosen and result in damage to the threading of the steering drag link connector. This could cause a separation in the drag link resulting in a loss of steering control. FCA determined that only the 4WD style drag link was affected and did not recall trucks with the 2WD style drag link due to design differences that made it unsusceptible to this failure mode. The repair remedy called for the steering coupler to be tightened to the proper torque prior to the jam nut being spot welded to the coupler body. If the coupler has already become detached or correct torque cannot be obtained, the drag link is to be replaced with an updated unit that went into production on the MY2019 RAM trucks.This updated unit uses a clamp to secure the coupler in place of the jam nuts used on original style components. In order to determine if the 2WD drag link was susceptible to the same defect found on the 4WD vehicles, ODI requested that our Vehicle Research and Test Center (VRTC) conduct testing on both RAM 2500 4WD and 2WD trucks. This testing was to determine operating conditions that might lead to loosened jam nuts of the recalled 4WD design and recreate these conditions on the 2WD vehicles to discover whether the 2WD design would also experience the loosening defect. Results from VRTC’s dynamic testing indicated that when the jam nuts are significantly under-torqued, they may loosen further from regular vehicle operation on the 4WD vehicles. Further, VRTC testing does not refute FCA’s assertion that the failure mechanism does not exist in the 2WD steering system. At the time of this closing resume, ODI has only received two allegations of drag link separation on 2WDvehicles.Neither could be validated as resulting from loose jam nuts. Since the release of recall 19V-021 ODI has received consumer complaints regarding the appearance of the spot weld applied to the defective drag link and the inability to have the steering properly aligned after welding of the jam nut. In September 2023, FCA provided owners with a supplemental Vehicle Alignment Clarification notification that provided information on an updated alignment procedure. Regarding the spot weld remedy used on the 4WD vehicles, ODI is concerned about the remedy in that during an alignment by a non-dealer repair facility, the spot weld might not be replaced after the alignment. To date there is no complaint trend of post alignment drag link separations, weld failures or other safety related incidents on remedied vehicles. This investigation is being closed with no further action. The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist. The Agency reserves the right to take additional action if warranted by future circumstances.
PE18016 · Steering Loss Due To Linkage Separation
Opened Dec 17, 2018 · Closed Dec 12, 2019
Status: closed (inferred from source dates) · Steering:linkages:drag:link:connection
On December 17, 2018, NHTSA's Office of Defects Investigation (ODI) opened Preliminary Evaluation (PE) 18-016 to investigate the steering system on model year (MY) 2015 and 2016 Ram 2500 manufactured by FCA US, LLC (FCA). Four complaints were received alleging separation of the drag link, a steering linkage that connects between the right front steering knuckle and the pitman arm on the steering box output shaft. The failures were found to be at a threaded coupler within the drag link used for adjusting the length of the linkage during routine maintenance (alignment) of the steering system.Once separation occurs, turning the steering wheel has no effect, and there is no way for the driver to control or maintain the direction of the vehicle. During the investigation, it was determined that the same threaded coupler was used on two different drag link designs FCA manufactured on MY 2013-2018 Ram 2500 and 3500 pickups. FCA refers to the designs as either 4x2 or 4x4 style. In both designs, the coupler is prevented from turning on the drag link via two jam nuts that are tightened against the coupler. In its response to NHTSA's March 15, 2019, Information Request (IR) letter, FCA identified 48 incidents alleging separation of the steering linkage at the coupler resulting in a loss of steering control. Of those, 13 involved a crash, one of which resulted in an injury. All of the separations involved the 4x4 style drag link. Additionally, FCA's IR response refers to over 300 4x4 style equipped vehicles that experienced, or may have experienced loosening of one or more coupler jam nuts. On January 25, 2019, FCA submitted a Defect Information Report (DIR) initiating NHTSA Recall No. 19V-021. In its DIR, FCA stated that the outboard jam nut in certain MY 2013-2018 Ram 2500 and 3500 could loosen potentially resulting in damage to the coupler and/or drag link threading allowing one end of the drag link to separate. The DIR notes that drag link separation results in loss of steering control, which in turn can cause a crash without warning. FCA's DIR did not identify a root cause for the defect, however it posits that an improperly torqued outboard jam nut could loosen, and with long-term vehicle use, cause damage to the outer link bar and/or coupler threads due to relative motion between the two components. The scope of Recall 19V-021 included vehicles with the 4x4 style drag link only. Also discussed in its IR response, FCA noted that the 4x2 style drag link contains a design difference (the outboard portion of the drag link is straight while the 4x4 style contains a bend) which it suggests may result in differences in the mechanical (bending) loads presented at the coupler and jam nut interface. Moreover, the DIR states that While root cause of the 4x4 style defect has not been established, FCA US believes that bending loads on the drag link is, at least, a causal contributing factor. FCA notes it did not identify any reports alleging 4x2 style separation as well as only three reports of loosening of jam nuts, two of which resulted in loosening that provided obvious warning to the vehicle operator, indicating a different failure mode.NHTSA is upgrading this investigation to Engineering Analysis (EA) 19-004 in order to continue to monitor the subject 4x2 style vehicles for evidence of field failures. Additionally, in conjunction with NHTSA's Vehicle Research and Test Center, ODI intends to more thoroughly study potential root cause(s) of the 4x4 style defect mechanism, and if identified, will seek to determine if the 4x2 drag link is susceptible to the same mechanism(s). NHTSA will also evaluate the long-term suitability of the recall
RQ15004 · Software Security Vulnerability
Opened Jul 24, 2015 · Closed Jan 5, 2016
Status: closed (inferred from source dates) · Electrical System:software
On July 23, 2015, Fiat Chrysler Automobiles (FCA) launched Safety Recall 15V-461 to remedy security vulnerabilities in approximately 1.4 million model year (MY) 2013 through 2015 vehicles equipped with Uconnect head units (HU) 8.4A (RA3 radio) and 8.4AN (RA4 radio) manufactured by Harman International.On July 24, 2015, the Office of Defects Investigation (ODI) opened Recall Query, RQ 15-004, to investigate HU security vulnerabilities and remedy effectiveness in the recalled population and to determine whether similar units have been supplied for use in other FCA vehicles.In an August 11, 2015 letter, FCA submitted a second Part 573 safety recall report expanding the scope of the Uconnect RA4 model radio to include additional 7,810 MY 2015 Jeep Renegade vehicles manufactured from September 18, 2014 through June 25, 2015 (Recall 15V-508).Scope analysis indicated that Uconnect radios installed in FCA vehicles not included in recalls 15V-461 or 15V-508 (subject recalls) are not equipped with built-in cellular access or short range wireless communication features and, thus, do not contain the security vulnerabilities addressed by the subject recalls. SUBJECT VEHICLES: MY2014 through 2015 Dodge Durango, Jeep Grand Cherokee and Jeep Cherokee sport utility vehicles; MY2013 through 2015 Ram 1500, 2500, 3500 and 4500/5500 pickup trucks; MY2013 through 2015 Dodge Viper vehicles; and MY2015 Chrysler 200, 300, Jeep Renegade, Dodge Charger and Challenger vehicles.According to FCA, long and short range wireless vulnerabilities identified in the recalled vehicles could allow unauthorized third-party access to, and manipulation of, networked vehicle control systems.Successful exploitation of the vulnerabilities, coupled with reverse engineering of networked microprocessor control modules, could result in unauthorized manipulation of vehicle control systems. This unauthorized manipulation of vehicle controls and systems could expose the driver, vehicle occupants or other highway users to an increased risk of injury.FCA and its network provider, Sprint, conducted a nationwide campaign to block access to a radio communications port that was unintentionally left open.On July 27, 2015, short range wireless vulnerabilities were also blocked.Finally, third party security evaluation and regression testing identified vulnerabilities that were either remedied by Sprint or through updates to the FCA Uconnect software.ODI identified a total of 30 complaints or field reports on unique vehicles submitted by FCA (29) or received by NHTSA (1) alleging incidents of theft from a vehicle or anomalous performance that the owner alleged were caused by, or may have been caused by, remote hacking.Twenty-six (87%) of these reports were submitted after a magazine article was published on July 21, 2015, describing the remote hacking of an FCA vehicle by researchers who were able to affect the operation of various vehicle control systems, including the service brakes, steering, throttle and ignition.Most of the complaints involved vehicle systems that were not safety critical (e.g., complaints related to radio, navigation system, or air-conditioning control) and did not affect vehicle control.Three complaints reported engine stalls.One owner reported sudden unintended acceleration allegedly related to hacking.None of the complaints or field reports reviewed involved the steering and braking vehicle control effects demonstrated by the research hackers prior to the recall.There were no confirmed incidents of hacking in any of the records reviewed by ODI.The remedies completed by Sprint and FCA appear to have eliminated vulnerabilities that mi
Illustration