My truck all of sudden put up the ABS light, traction control light, emergency brake light and loss of cruise control. Had it test at an O'reilly and has a C-2200-49 ABS module failure internal module failure.
2017 RAM 1500
Owner reports · Recalls · Investigations
Similar to other model years
Owner complaints for the 2017 RAM 1500 do not stand out strongly from the model-year median of 616.
About this comparison →How this year compares
Owner complaints by model year
Compare all 1500 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
All reported categories
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
359 reports with mileage · 511 unknown
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Steering. Review the 222 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine. Review the 156 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Electrical System. Review the 108 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
Electrical System complaints
108 reportsThe ABS/brake warning lights illuminated on my 2017 Ram 1500. I have not noticed a difference in normal braking performance. Diagnostic testing identified codes C2200-49 related to an internal ABS module electronic failure and C0020-01, ABS pump motor control/general electrical failure. I was advised that the ABS module and/or h…
Read full complaint
The ABS/brake warning lights illuminated on my 2017 Ram 1500. I have not noticed a difference in normal braking performance. Diagnostic testing identified codes C2200-49 related to an internal ABS module electronic failure and C0020-01, ABS pump motor control/general electrical failure. I was advised that the ABS module and/or hydraulic control unit may require replacement. I am concerned that the ABS system may not function properly when needed. I am also aware that certain 2017-2018 Ram 2500 and other heavy-duty Ram models have been recalled under NHTSA Campaign 24V-896 for HCU failure resulting in loss of ABS, stability control and traction control. I have found reports of similar ABS failures involving Ram 1500 vehicles, which are not included in that recall. I am submitting this complaint so NHTSA can evaluate whether this represents a broader safety defect.
Odometer Fraud. The contact purchased a 2017 Ram 1500. It was discovered that there was a mileage discrepancy. The vehicle was a private sale in a parking lot with an interpreter. At the time of purchase, the vehicle mileage was 117,777; it was discovered that the mileage was 166,000 on the Carfax report. The contact filed a com…
Read full complaint
Odometer Fraud. The contact purchased a 2017 Ram 1500. It was discovered that there was a mileage discrepancy. The vehicle was a private sale in a parking lot with an interpreter. At the time of purchase, the vehicle mileage was 117,777; it was discovered that the mileage was 166,000 on the Carfax report. The contact filed a complaint with the Attorney General online.
Per my dealer, Hudson Chrysler Dodge Jeep of Hudson, WI the ABS Module in my 2017 Ram 1500 has failed, and needs to be replaced. The part is on permanent backorder with no eta on production or shipping. There are thousands of complaints online regarding this issue, that Ram is not correcting. My dealer told me they may never …
Read full complaint
Per my dealer, Hudson Chrysler Dodge Jeep of Hudson, WI the ABS Module in my 2017 Ram 1500 has failed, and needs to be replaced. The part is on permanent backorder with no eta on production or shipping. There are thousands of complaints online regarding this issue, that Ram is not correcting. My dealer told me they may never receive the part, and there is no solution for it. The part number is 68295368AC
The vehicle is a 2017 Ram 1500 Big Horn EcoDiesel 4x4 that I bought new in 2018. The backup camera has been a constant intermittent problem since the second year of ownership. It will go dark, have a green screen, or display scrambled lines. The camera has been replaced by the local Ram dealer (Mullahey Jeep/Dodge/Ram…
Read full complaint
The vehicle is a 2017 Ram 1500 Big Horn EcoDiesel 4x4 that I bought new in 2018. The backup camera has been a constant intermittent problem since the second year of ownership. It will go dark, have a green screen, or display scrambled lines. The camera has been replaced by the local Ram dealer (Mullahey Jeep/Dodge/Ram in Paso Robles, CA) at least once under warranty, but the problem recurred. It has been there at other times for the issue, but the problem had rectified itself by the time I got it there. After researching this on the internet the problem appears to be in the backup camera wiring harness in the tailgate, possibly in the electrical connectors. Many people complain about the issue on various forums, and there are quite a few videos on You Tube with homegrown fixes which I have tried, but they are a temporary at best. The best temporary remedy I have found is to open and then slam the tailgate shut. The problem appears to be quite common. I informed the dealer about the wiring harness possibly being the source of the problem the last time I brought it in a few years ago, but they seemed to ignore my advice. I know that there have been safety recalls of RAM pickups for backup camera issues from model years 2019 onwards, so why not other affected years? The problem most recently recurred today as I was backing out of my driveway. It has occurred numerous times over the years. RAM appears to have no permanent fix for this safety hazard. Luckily, I have not yet had an accident, but no one should have to wait for an accident, injury, or a fatality to order a recall. I hope my complaint does not fall on deaf ears as it has with RAM. Thank you.
Odometer Fraud. The contact purchased a 2017 Ram 1500. It was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. The contact called the dealer but there was no response due to the location being bankrupt. At the time of purchase, the vehicle mileage was 120,000. A Carfax report was obtained. it was d…
Read full complaint
Odometer Fraud. The contact purchased a 2017 Ram 1500. It was discovered that there was a mileage discrepancy. The vehicle was a dealer sale. The contact called the dealer but there was no response due to the location being bankrupt. At the time of purchase, the vehicle mileage was 120,000. A Carfax report was obtained. it was discovered that the mileage was 140,000.There was no other agency contacted.
The contact owns a 2017 Ram 1500. The contact stated that while driving at various speeds, the Traction Control, ABS, Electric Trailer Brake, and Brake warning lights illuminated. The vehicle was taken back to the local dealer, where it was purchased, and it was scanned with an OBD2 scanner; however, it was cleared for error cod…
Read full complaint
The contact owns a 2017 Ram 1500. The contact stated that while driving at various speeds, the Traction Control, ABS, Electric Trailer Brake, and Brake warning lights illuminated. The vehicle was taken back to the local dealer, where it was purchased, and it was scanned with an OBD2 scanner; however, it was cleared for error codes and diagnosed safe to drive. The vehicle was repaired; however, the failure occasionally reoccurred. The manufacturer was made aware of the failure. The failure mileage was approximately 106,200.
4-28-2026 - Service ABS illuminated, Emergency Brake Warning Light Stays Illuminated, and Electronic Stability Control Warning stays Illuminated. Had it at dealer on 4-30-2026. They tested system and said ABS CONTROL MODULE was working but sensor was bad and there was a backlog or over 20,000 customers waiting for replacement OE…
Read full complaint
4-28-2026 - Service ABS illuminated, Emergency Brake Warning Light Stays Illuminated, and Electronic Stability Control Warning stays Illuminated. Had it at dealer on 4-30-2026. They tested system and said ABS CONTROL MODULE was working but sensor was bad and there was a backlog or over 20,000 customers waiting for replacement OEM parts. Engineers developed a replacement in 2023 but the replacement had a faulty chip and is not serviceable. As a result, there are over 20,000 RAM and Jeep owners driving around with unsafe vehicles. There is a safety recall for this issue but only calls out RAM 2500 and 3500 trucks.
Timeline of issues: 04/11/2026 – Vehicle purchased 04/16/2026 – Brakes began grinding 04/18/2026 – Vehicle developed starting issues 04/19/2026 – Brake system parts (pads, rotors, calipers) ordered due to failure 04/23/2026 – Parts received; same day 4WD was tested and confirmed not functioning properly (dashboard indicates eng…
Read full complaint
Timeline of issues: 04/11/2026 – Vehicle purchased 04/16/2026 – Brakes began grinding 04/18/2026 – Vehicle developed starting issues 04/19/2026 – Brake system parts (pads, rotors, calipers) ordered due to failure 04/23/2026 – Parts received; same day 4WD was tested and confirmed not functioning properly (dashboard indicates engagement but front wheels do not engage) 04/24/2026 – Complete brake failure occurred due to caliper failure These issues occurred immediately after purchase and indicate the vehicle had significant pre-existing mechanical defects at the time of sale. The 4WD system also does not function correctly despite indicating engagement, and the braking system failed completely shortly after purchase.
Electronic Power Steering just stopped all of a sudden while I was going up the mountain into North Carolina that almost caused an accident the only reason it didn’t is because of the pull off right after the curve I was going through when I lost all steering! With the truck already in the pull off I stopped to see if I had lost…
Read full complaint
Electronic Power Steering just stopped all of a sudden while I was going up the mountain into North Carolina that almost caused an accident the only reason it didn’t is because of the pull off right after the curve I was going through when I lost all steering! With the truck already in the pull off I stopped to see if I had lost a serpentine belt unaware this Ram is equipped with the EPS System. I had no phone service luckily someone came by when they did because of the snow storm seeing vehicles was few and far between! After letting the truck sit for about 20mins with the positive cable unhooked I started the truck and had steering again. So the nice gentleman that stopped said he would follow me to the nearest cell service area so I could call someone, No warning light the first time at all the second time the only warning light was service ABS system which shouldn’t affect having power steering. So I repeated the steps as I did the first time and had steering again the service ABS System light was gone and we made it 11 Minutes up the mountain before it happened again only this time all kinds of service lights came on all at once, Service Electronic brake system,Service ANTILOCK BRAKE SYSTEM, SERVICE ELECTRONIC SHIFTER, SERVICE POWER STEERING SYSTEM, traction control was disabled which isn’t good in snowy weather conditions and i had no choice but to continue 3mins to the next town with no power steering no traction control and all these other warning lights because it wouldn’t fix it anymore temporarily by in hooking the positive battery cable and waiting 20 minutes which I attempted 3 times with no success once we reached the town I was able to call and have someone come pick me and my truck up and brought a scan tool I cleared the codes only for them to come right back as soon as I would crank the truck! Had it professionally scanned with same results! Very dangerous issue! Yes it can be inspected yes professionally inspected $2300part only not labor to!
Official recalls
1325V010000 · Air Bags:side/window:curtain:inflator
Jan 16, 2025
Chrysler (FCA US, LLC) is recalling certain 2016-2019 Ram 3500, Ram 1500, 2016-2020 Ram 2500, and 2016 Ram 3500 Cab Chassis vehicles. The right and left side curtain air bag inflators may rupture due to a manufacturing defect.
Consequence & remedy
Consequence: An inflator rupture may result in sharp metal fragments striking occupants, resulting in injury.
Remedy: Dealers will replace one or both side curtain air bags, as necessary, free of charge. Owner notification letters were mailed February 13, 2025. Owners may contact FCA customer service at 1-800-853-1403. FCA's numbers for this recall are 05C, 09C, and 10C.
23V411000 · Engine And Engine Cooling
Jun 8, 2023
Chrysler (FCA US, LLC) is recalling certain 2014-2019 Ram 1500 and 2014-2020 Jeep Grand Cherokee vehicles equipped with 3.0L Diesel engines. The crankshaft position sensor tone wheel may delaminate, causing the engine to lose its ability to synchronize the fuel injector pulses and cam shaft timing, possibly resulting in an engine stall.
Consequence & remedy
Consequence: An engine stall can increase the risk of a crash.
Remedy: Dealers will update the powertrain control module software to maintain vehicle propulsion, free of charge. Interim notification letters, notifying owners of the safety risk, were mailed August 3, 2023. Some owner notification letters were mailed October 31, 2023. The remaining owner notification letters will be mailed at a future date, anticipated July 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is 66A. This recall is an expansion of recall 20V-475.
22V406000 · Fuel System, Diesel:delivery:fuel Pump
Jun 9, 2022
Chrysler (FCA US, LLC) is recalling certain 2014-2020 Jeep Grand Cherokee, and 2014-2019 Ram 1500 vehicles equipped with 3.0L diesel engines. A high pressure fuel pump (HPFP) failure may introduce internal debris into the fuel system, potentially resulting in fuel starvation.
Consequence & remedy
Consequence: Fuel starvation may result in an unexpected loss of drive power, increasing the risk of a crash.
Remedy: Dealers will replace the HPFP, and inspect and replace, if necessary, additional fuel system components, free of charge. Interim notification letters informing owners of the safety risk were mailed July 21, 2022. Owner notification letters for were mailed for Jeep Grand Cherokee owners starting January 11, 2024. Owner notification letters for Ram 1500 owners were mailed March 7, 2024. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLS's number for this recall is Z46.
21V632000 · Air Bags:side/window:curtain; Air Bags:side/window:curtain:inflator
Aug 12, 2021
Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
Consequence & remedy
Consequence: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
Remedy: Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.
Additional source detail variants (2)
Air Bags:side/window:curtain:inflator
Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
Consequence: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
Remedy: Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.
Air Bags:side/window:curtain
Chrysler (FCA US, LLC) is recalling certain 2015-2020 Ram 1500 Classic, 2015-2016 Ram 3500, and Ram 2500 vehicles, and 2016 Ram 3500 Cab Chassis with a gross vehicle weight rating less than 10,000 lbs. The side air bag inflatable curtain (SABIC) inflator end cap may detach from the inflator, or the inflator sidewall may rupture.
Consequence: A separated inflator end cap or inflator rupture can allow compressed gas to escape, resulting in the end cap or other components being propelled into the vehicle, increasing the risk of injury or crash.
Remedy: Dealers will inspect and replace as necessary, the SABIC assemblies, free of charge. Interim owner notification letters were mailed on October 4, 2021. Owner notification letters were mailed on May 26, 2022. Owners may contact FCA US, LLC customer service at 1-800-853-1403. FCA US, LLC's number for this recall is Y55.
20V475000 · Engine And Engine Cooling:engine:diesel
Aug 13, 2020
Chrysler (FCA US LLC) is recalling certain 2014-2018 Ram 1500 and 2014-2016 Jeep Grand Cherokee vehicles equipped with 3.0L diesel engines. The crankshaft position sensor tone wheel may delaminate causing the engine to lose its ability to synchronize the fuel injector pulses and cam shaft timing, possibly resulting in an engine stall.
Consequence & remedy
Consequence: An engine stall can increase the risk of a crash.
Remedy: FCA US will notify owners, and dealers will update the powertrain control module software to maintain vehicle propulsion by reading the camshaft position signal in the event that the crankshaft position signal is lost, free of charge. Owner notification letters were mailed on May 13, 2021. Owners may contact FCA US customer service at 1-800-853-2002. FCA US's number for this recall is W58.
19V757000 · Engine And Engine Cooling:exhaust System:emission Control:gas Recirculation Valve (egr Valve)
Oct 24, 2019
Chrysler (FCA US LLC) is recalling certain 2014-2019 Ram 1500 and 1500 Classic Pickup trucks equipped with 3.0L Eco Diesel engines. The Exhaust Gas Recirculation (EGR) cooler may crack and allow pre-heated vaporized coolant to enter the EGR system. This mixture may combust inside the intake manifold.
Consequence & remedy
Consequence: Combustion in the intake manifold can increase the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the EGR cooler, free of charge. Dealers will also inspect and, as necessary, replace the intake manifold. The recall began April 16, 2020. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is VB1.
19V347000 · Latches/locks/linkages:tailgate:latch
May 9, 2019
Chrysler (FCA US LLC) is recalling certain 2015-2017 Ram 1500, 2500 and 3500 pickup trucks equipped with an 8 foot bed and a power locking tailgate. Chrysler is also recalling all 2013-2014 and 2018 Ram 1500, 2500 and 3500 pickup trucks built before April 1, 2018 with a 6 or 8 foot bed and a power locking tailgate. On August 29, 2019 Chrysler expanded the recall to include an additional 693,128 model year 2013-2014 Ram 1500, 2500 and 3500 pickup trucks. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence & remedy
Consequence: If the tailgate opens while the vehicle is being driven, cargo may fall out the vehicle and create a road hazard, increasing the risk of crash.
Remedy: Chrysler will notify owners, and dealers will repair the tailgate latch, free of charge. The recall began May 23, 2019. Chrysler is expected to notify owners of the expanded population on October 18, 2019. Owners may contact FCA US customer service at 1-800-853-1403. FCA US's number for this recall is V44. Note: 2015-2017 MY Ram 1500 pickup trucks with truck beds other than 8 foot, are currently covered under NHTSA recall 18V-486 for this issue.
18V486000 · Latches/locks/linkages:tailgate:latch; Structure:body:tailgate
Jul 27, 2018
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence & remedy
Consequence: If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.
Additional source detail variants (2)
Latches/locks/linkages:tailgate:latch
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence: If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.
Structure:body:tailgate
Chrysler (FCA US LLC) is recalling certain 2015-2017 RAM 1500, 2500, and 3500 pickup trucks equipped with a power locking tailgate and either a 5 foot, 7 inch or 6 foot, 4 inch bed. The tailgate actuator limiter tab may fracture and cause the tailgate to unlatch and open while driving.
Consequence: If the tailgate latch releases and the tailgate opens while driving, cargo may fall out, creating a road hazard and increasing the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will repair the vehicle, free of charge. The recall began September 17, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U74.
18V332000 · Electrical System:software; Electrical System:wiring; Vehicle Speed Control:cruise Control
May 17, 2018
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence & remedy
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Additional source detail variants (3)
Electrical System:software
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Vehicle Speed Control:cruise Control
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
Electrical System:wiring
Chrysler (FCA US LLC) is recalling certain 2014-2018 Dodge Journey, Charger and Durango, RAM 2500, 3500, 3500 Cab Chassis (more than 10,000lb), 4500 Cab Chassis and 5500 Cab Chassis, Jeep Cherokee and Grand Cherokee and Chrysler 300, 2014-2019 RAM 1500, 2015-2018 Dodge Challenger, 2015-2017 Chrysler 200, 2016-2018 RAM 3500 Cab Chassis (less than 10,000 lb), 2017-2018 Chrysler Pacifica and 2018 Jeep Wrangler vehicles. These vehicles are being recalled to address a defect that could prevent the cruise control system from disengaging. If, when using cruise control, there is a short circuit within the vehicle's wiring, the driver may not be able to shut off the cruise control either by depressing the brake pedal or manually turning the system off once it has been engaged, resulting in either the vehicle maintaining its current speed or possibly accelerating.
Consequence: If the vehicle maintains its speed or accelerates despite attempts to deactivate the cruise control, there would be an increased risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect the software, and perform a software flash on the engine or powertrain control module, free of charge. The recall began June 4, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Note: Owners are advised to stop using cruise control until the software update has been performed. In the event that cruise control cannot be disengaged while driving, owners should firmly and steadily apply the brakes and shift the transmission to neutral, placing the vehicle in park once it has stopped.
18V100000 · Power Train:automatic Transmission
Feb 8, 2018
Chrysler (FCA US LLC) is recalling certain 2017-2018 RAM 1500, 2500, 3500, 3500 Cab Chassis, 4500 Cab Chassis, and 5500 Cab Chassis vehicles, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
Consequence & remedy
Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy: Chrysler will notify owners and dealers will update the Body Control Module software. Dealers will also test the BTSI operation, replacing the solenoid as necessary. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is U11.
17V821000 · Power Train:automatic Transmission:lever And Linkage:column Shift
Dec 20, 2017
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 3500 Cab Chassis with a Gross Vehicle Weight Rating (GVWR) of less than 10,000 lbs, 2011-2017 Ram 3500, 4500 and 5500 Cab Chassis vehicles, 2009-2017 Ram 1500 and 2010-2017 Ram 2500 and 3500 pickup trucks, all equipped with a column shifter. Pushing the brake pedal for prolonged periods when the vehicle is running and in PARK may cause the Brake Transmission Shift Interlock (BTSI) pin to stick in the open position. With the pin in the open position, the transmission can be shifted out of PARK into any gear without pushing the brake pedal or having the key in the ignition.
Consequence & remedy
Consequence: Being able to shift the transmission without pushing the brake pedal and/or without a key in the ignition can increase the risk of an unintended vehicle rollaway that may result in personal injury or a crash.
Remedy: Chrysler will notify owners, and dealers will update the vehicle software, inspect the BTSI, and, as necessary, replace it, free of charge. The recall began February 26, 2018. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T79.
17V434000 · Fuel System, Gasoline:storage:tank Assembly
Jul 7, 2017
Chrysler (FCA US LLC) is recalling certain 2017 Ram 1500 trucks. The fuel tanks in the affected vehicles may have a broken fuel tank control valve which might leak fuel if the vehicle were to become inverted. As such, these vehicles fail to comply with the requirements of Federal Motor Vehicle Safety Standard (FMVSS) number 301, "Fuel System Integrity."
Consequence & remedy
Consequence: In the event of a rollover crash, leaking fuel in the presence of an ignition source can increase the risk of a fire.
Remedy: Chrysler will notify owners, and dealers will replace the fuel tanks, free of charge. The recall began on August 10, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T45.
17V198000 · Power Train:driveline:differential Unit
Mar 23, 2017
Chrysler (FCA US LLC) is recalling certain 2016-2017 Ram 1500 trucks. The differential pin retaining screw may come loose while driving, potentially causing the differential to break or lock up.
Consequence & remedy
Consequence: A broken or locked up differential may result in a loss of motive power and possibly a loss of vehicle control. Either scenario increases the risk of a crash.
Remedy: Chrysler will notify owners, and dealers will inspect and replace the differential retaining pin, free of charge. The recall began April 24, 2017. Owners may contact Chrysler customer service at 1-800-853-1403. Chrysler's number for this recall is T20.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
3RQ25003 · Post Recall Remedy Brake Transmission Shift Interlock (btsi) Failure
Opened Jul 3, 2025 · No close date supplied
Status: open (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:gear Position Indication (prndl)
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (2)
Power Train:automatic Transmission
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
Power Train:automatic Transmission:gear Position Indication (prndl)
The Office of Defects Investigation (ODI) has received 14 Vehicle Owner Questionnaire (VOQ) reports and 6 EWR Death & Injury (D&I) reports describing post recall remedy failures of the brake transmission shift interlock (BTSI) system in certain Model Year (MY) 2013-2018 RAM pickup trucks.The subject vehicle models include 1500, 2500, 3500, 4500, and 5500 trucks equipped with a column mounted shift lever.The failures of the BTSI described in the VOQs occurred on vehicles that had all previously been repaired under recall 17V-821 or 18V-100.Both recalls address a potential condition which can cause the BTSI locking pin to become stuck allowing the transmission to be shifted out of Park without depressing the brake pedal and/or without having a key in the ignition.Shifting the transmission out of Park when not having the brake pedal depressed can result in a vehicle rollaway. ODI is opening this Recall Query (RQ) to review the effectiveness of the 17V-821 and 18V-100 recall remedies, understand the root cause of additional vehicle rollaway incidents, and identify any other possible root cause that may affect the performance of the BTSI system. To review the ODI reports cited in the Opening Resume ODI Report Identification Number document, go to NHTSA.gov.
EA23001 · High Pressure Fuel Pump Failure
Opened Mar 17, 2023 · No close date supplied
Status: open (inferred from source dates) · Fuel System, Diesel:delivery:fuel Pump
The Office of Defects Investigation (ODI) opened PE21-021 on October 14, 2021, to investigate incidents alleging a stall/loss of motive power as a result of high-pressure fuel pump failures in certain model year (MY) 2019-2020 Ram 2500, 3500, 4500, and 5500 heavy duty trucks equipped with 6.7L Cummins turbodiesel engines. During the investigation, ODI sought to determine if the related defect allegation was limited in scope to the recalled population. After review of information request response materials from both FCA and BMW, NHTSA determined that sufficient information to identify a comprehensive recall population could not be produced by FCA and BMW.During the investigation FCA filed recalls 22V406, 22E048, 22V767, and 22E087 which include vehicles not identified in the initial subject population by ODI. ODI also received recall 21V586, involving loss of motive power due to failed CP4 fuel pumps on certain BMW manufactured vehicles. An information request letter response received from BMW indicated that failed pumps on their vehicles were caused by an interaction between pump internal components and US market diesel fuel, leading to increased slip and eventual particle-generating wear surface. Additional work will be done to identify whether a similar root cause is associated with the FCA recalled population and if similar wear dynamics occur on pumps supplied to vehicle manufacturers other than those included in the recalled population.ODI has upgraded this investigation to an EA in order to 1) determine engineering specifications of internal pump components that are correlated with pump failure leading to loss of motive power or other safety related hazards, 2) identify vehicle populations equipped with alleged defective pump variants, 3) assess if vehicles equipped with alleged defective pump variants result in an unreasonable risk to motor vehicle safety and 4) gather and review any other relevant information related to high pressure fuel pump failure associated with the subject populations of recalls 21V586, 21V880, 21E094, 22V406, 22E048, 22V767, and 22E087.Review of the above information will allow NHTSA to confirm root cause and recall remedy viability, and identify and evaluate vehicle populations equipped with pump components that may pose an unreasonable risk to motor vehicle safety.The ODI reports cited above can be reviewed at: http://www-odi.nhtsa.dot.gov/owners/SearchNHTSAID using the following complaint identification numbers: 11257550, 11351441, 11361603, 11361616, 11365300, 11365426, 11365858, 11366401, 11372337, 11373793, 11374797, 11376793, 11377871, 11378173, 11384377, 11386063, 11387018, 11399710, 11402550, 11415339, 11418868, 11418870, 11427075, 11434276, 11436807, 11437226, 11437249, 11437273, 11437292, 11437294, 11437394, 11437399, 11437403, 11437405, 11437423, 11437528, 11437565, 11437579, 11437580, 11437590, 11437679, 11437744, 11437781, 11437842, 11437993, 11438006, 11438008, 11438121, 11438138, 11438155, 11438392, 11438629, 11439359, 11439879, 11440397, 11443030, 11446542, 11448163, 11453556, 11458918, 11460558, 11469337
PE16014 · Vehicle Rollaway
Opened Dec 16, 2016 · Closed Jan 25, 2024
Status: closed (inferred from source dates) · Power Train:automatic Transmission; Power Train:automatic Transmission:control Module (tcm/pcm/tecm); Power Train:automatic Transmission:gear Position Indication (prndl)
Basis – On December 16, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-014 to investigate 43 vehicle rollaway incidents with operators alleging they had shifted to Park and then exited the vehicle prior to the rollway incidents. These complaints involved multiple Fiat Chrysler Automobiles (FCA) model and model year vehicles that share a common electronic rotary shifter design. Of the 43 consumer complaints, 25 complaints alleged crashes, and eight complaints alleged at least one injury. Subject Vehicles – When NHTSA opened the investigation, the subject vehicles were model year (MY) 2013-2016 Ram 1500 vehicles and MY 2014-2016 Dodge Durango vehicles equipped with a rotary electronic shifter. However, NHTSA expanded the scope of the investigation to include subsequent model years of the same model vehicles when the Agency learned that those new model year vehicles use the same rotary shifter. Additionally, all subject vehicles manufactured by FCA are equipped with electronic rotary shifters supplied by Kostal Automotive. Reason for closing - During the course of this investigation, ODI did not find evidence that a vehicle-based design or manufacturing defect was the cause of vehicle rollaway incidents on the subject vehicles. Nevertheless, given the risk of a vehicle rollaway, FCA’s CSN actions provide automated vehicle securement when an operator attempts to exit the vehicle without successfully achieving a Park position with the rotary shifter mechanism. ODI closely monitored the subject vehicles on which the CSN actions implement a vehicle securement strategy and found that the CSN actions were effective in reducing the frequency of vehicle rollaway incidents in the subject vehicles. ODI analyzed the incidents when a CSN had been implemented and a rollaway still occurred, and ODI was unable to find an actionable defect that caused vehicle rollaway incidents. ODI found that the failure rates on subject vehicles that received a CSN remedy were similar to the failure rates on other vehicle populations and additionally had similar mechanisms as other vehicle populations such as slippery surfaces and various mechanical failures. Furthermore, as discussed above, after FCA’s release of the CSN actions, consumer complaints have decreased significantly. Given the absence of an identified safety defect based on available information and FCA’s customer satisfaction campaign which addresses the failure mode, further action is not warranted at this time. Accordingly, this Preliminary Evaluation is closed. However, the Agency reserves the right to take further action, if warranted.Please see the attached detailed closing summary for more information. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Additional source detail variants (3)
Power Train:automatic Transmission
Basis – On December 16, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-014 to investigate 43 vehicle rollaway incidents with operators alleging they had shifted to Park and then exited the vehicle prior to the rollway incidents. These complaints involved multiple Fiat Chrysler Automobiles (FCA) model and model year vehicles that share a common electronic rotary shifter design. Of the 43 consumer complaints, 25 complaints alleged crashes, and eight complaints alleged at least one injury. Subject Vehicles – When NHTSA opened the investigation, the subject vehicles were model year (MY) 2013-2016 Ram 1500 vehicles and MY 2014-2016 Dodge Durango vehicles equipped with a rotary electronic shifter. However, NHTSA expanded the scope of the investigation to include subsequent model years of the same model vehicles when the Agency learned that those new model year vehicles use the same rotary shifter. Additionally, all subject vehicles manufactured by FCA are equipped with electronic rotary shifters supplied by Kostal Automotive. Reason for closing - During the course of this investigation, ODI did not find evidence that a vehicle-based design or manufacturing defect was the cause of vehicle rollaway incidents on the subject vehicles. Nevertheless, given the risk of a vehicle rollaway, FCA’s CSN actions provide automated vehicle securement when an operator attempts to exit the vehicle without successfully achieving a Park position with the rotary shifter mechanism. ODI closely monitored the subject vehicles on which the CSN actions implement a vehicle securement strategy and found that the CSN actions were effective in reducing the frequency of vehicle rollaway incidents in the subject vehicles. ODI analyzed the incidents when a CSN had been implemented and a rollaway still occurred, and ODI was unable to find an actionable defect that caused vehicle rollaway incidents. ODI found that the failure rates on subject vehicles that received a CSN remedy were similar to the failure rates on other vehicle populations and additionally had similar mechanisms as other vehicle populations such as slippery surfaces and various mechanical failures. Furthermore, as discussed above, after FCA’s release of the CSN actions, consumer complaints have decreased significantly. Given the absence of an identified safety defect based on available information and FCA’s customer satisfaction campaign which addresses the failure mode, further action is not warranted at this time. Accordingly, this Preliminary Evaluation is closed. However, the Agency reserves the right to take further action, if warranted.Please see the attached detailed closing summary for more information. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Power Train:automatic Transmission:control Module (tcm/pcm/tecm)
Basis – On December 16, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-014 to investigate 43 vehicle rollaway incidents with operators alleging they had shifted to Park and then exited the vehicle prior to the rollway incidents. These complaints involved multiple Fiat Chrysler Automobiles (FCA) model and model year vehicles that share a common electronic rotary shifter design. Of the 43 consumer complaints, 25 complaints alleged crashes, and eight complaints alleged at least one injury. Subject Vehicles – When NHTSA opened the investigation, the subject vehicles were model year (MY) 2013-2016 Ram 1500 vehicles and MY 2014-2016 Dodge Durango vehicles equipped with a rotary electronic shifter. However, NHTSA expanded the scope of the investigation to include subsequent model years of the same model vehicles when the Agency learned that those new model year vehicles use the same rotary shifter. Additionally, all subject vehicles manufactured by FCA are equipped with electronic rotary shifters supplied by Kostal Automotive. Reason for closing - During the course of this investigation, ODI did not find evidence that a vehicle-based design or manufacturing defect was the cause of vehicle rollaway incidents on the subject vehicles. Nevertheless, given the risk of a vehicle rollaway, FCA’s CSN actions provide automated vehicle securement when an operator attempts to exit the vehicle without successfully achieving a Park position with the rotary shifter mechanism. ODI closely monitored the subject vehicles on which the CSN actions implement a vehicle securement strategy and found that the CSN actions were effective in reducing the frequency of vehicle rollaway incidents in the subject vehicles. ODI analyzed the incidents when a CSN had been implemented and a rollaway still occurred, and ODI was unable to find an actionable defect that caused vehicle rollaway incidents. ODI found that the failure rates on subject vehicles that received a CSN remedy were similar to the failure rates on other vehicle populations and additionally had similar mechanisms as other vehicle populations such as slippery surfaces and various mechanical failures. Furthermore, as discussed above, after FCA’s release of the CSN actions, consumer complaints have decreased significantly. Given the absence of an identified safety defect based on available information and FCA’s customer satisfaction campaign which addresses the failure mode, further action is not warranted at this time. Accordingly, this Preliminary Evaluation is closed. However, the Agency reserves the right to take further action, if warranted.Please see the attached detailed closing summary for more information. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Power Train:automatic Transmission:gear Position Indication (prndl)
Basis – On December 16, 2016, the Office of Defects Investigation (ODI) opened Preliminary Evaluation PE16-014 to investigate 43 vehicle rollaway incidents with operators alleging they had shifted to Park and then exited the vehicle prior to the rollway incidents. These complaints involved multiple Fiat Chrysler Automobiles (FCA) model and model year vehicles that share a common electronic rotary shifter design. Of the 43 consumer complaints, 25 complaints alleged crashes, and eight complaints alleged at least one injury. Subject Vehicles – When NHTSA opened the investigation, the subject vehicles were model year (MY) 2013-2016 Ram 1500 vehicles and MY 2014-2016 Dodge Durango vehicles equipped with a rotary electronic shifter. However, NHTSA expanded the scope of the investigation to include subsequent model years of the same model vehicles when the Agency learned that those new model year vehicles use the same rotary shifter. Additionally, all subject vehicles manufactured by FCA are equipped with electronic rotary shifters supplied by Kostal Automotive. Reason for closing - During the course of this investigation, ODI did not find evidence that a vehicle-based design or manufacturing defect was the cause of vehicle rollaway incidents on the subject vehicles. Nevertheless, given the risk of a vehicle rollaway, FCA’s CSN actions provide automated vehicle securement when an operator attempts to exit the vehicle without successfully achieving a Park position with the rotary shifter mechanism. ODI closely monitored the subject vehicles on which the CSN actions implement a vehicle securement strategy and found that the CSN actions were effective in reducing the frequency of vehicle rollaway incidents in the subject vehicles. ODI analyzed the incidents when a CSN had been implemented and a rollaway still occurred, and ODI was unable to find an actionable defect that caused vehicle rollaway incidents. ODI found that the failure rates on subject vehicles that received a CSN remedy were similar to the failure rates on other vehicle populations and additionally had similar mechanisms as other vehicle populations such as slippery surfaces and various mechanical failures. Furthermore, as discussed above, after FCA’s release of the CSN actions, consumer complaints have decreased significantly. Given the absence of an identified safety defect based on available information and FCA’s customer satisfaction campaign which addresses the failure mode, further action is not warranted at this time. Accordingly, this Preliminary Evaluation is closed. However, the Agency reserves the right to take further action, if warranted.Please see the attached detailed closing summary for more information. To review the ODI reports cited in the Closing Resume ODI Report Identification Number document, go to NHTSA.gov.
Illustration