Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 13 of 13 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
Engine. Review the 11 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Engine And Engine Cooling. Review the 2 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
Vehicle Speed Control. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
What owners actually said
13 reports
42,000 miles · Apr 19, 2013
Engine
I WAS CRUISING WITH THE FAMILY AT 65MPH AND HEARD MY BELTS SQUEEL AND THEN STOP AFTER 2 OR 3 SECONDS. ABOUT 20 SECONDS LATER A LOW COOLANT LIGHT CAME ON AND MY TEMP LIGHT WAS BLINKING. TEMP WAS ONLY AROUND 195 TO 205, PRETTY FAR FROM THE RED. I IMMEDIATLY PULLED OVER AND SHUT IT DOWN. THERE WAS A LOT OF COOLANT LEAKING, A LARGE …
Read full complaint
I WAS CRUISING WITH THE FAMILY AT 65MPH AND HEARD MY BELTS SQUEEL AND THEN STOP AFTER 2 OR 3 SECONDS. ABOUT 20 SECONDS LATER A LOW COOLANT LIGHT CAME ON AND MY TEMP LIGHT WAS BLINKING. TEMP WAS ONLY AROUND 195 TO 205, PRETTY FAR FROM THE RED. I IMMEDIATLY PULLED OVER AND SHUT IT DOWN. THERE WAS A LOT OF COOLANT LEAKING, A LARGE TRAIL FOLLOWED ME OFF THE INTERSTATE. *TR
NHTSA ODI #10508852
80,244 miles · Feb 23, 2013
Engine
COOLANT PIPE FAILURE AT "COOLANT CONSOLE" ON TOP OF THE ENGINE CAUSING ALL COOLANT TO IMMEDIATELY SPILL ON TOP THE ENGINE, SPRAYING THE REAR TIRES CAUSING REAR TIRES TO LOSE TRACTION. THE COOLANT PIPE IS PRESS FIT WITH WHAT APPEARS TO BE AN ADHESIVE WHICH FAILED LEAVING THE EXIT PIPE MADE OF STEEL SEPARATED FROM AN ALUMINUM " C…
Read full complaint
COOLANT PIPE FAILURE AT "COOLANT CONSOLE" ON TOP OF THE ENGINE CAUSING ALL COOLANT TO IMMEDIATELY SPILL ON TOP THE ENGINE, SPRAYING THE REAR TIRES CAUSING REAR TIRES TO LOSE TRACTION. THE COOLANT PIPE IS PRESS FIT WITH WHAT APPEARS TO BE AN ADHESIVE WHICH FAILED LEAVING THE EXIT PIPE MADE OF STEEL SEPARATED FROM AN ALUMINUM " CONSOLE OR BLOCK". THE COOLANT LOSS WAS IMMEDIATE CAUSING TOTAL COOLANT LOSS. VERY DISCONCERTING AT 70MPH HAVING COOLANT SPRAY ALL OVER THE REAR TIRES (PARTICULARLY THE DRIVERS SIDE REAR). CAUSING THE REAR OF THE CAR TO SLIDE SIDEWAYS ON A GENTLE RIGHT HAND BEND ON AN INTERSTATE. *TR
NHTSA ODI #10499809
54,000 miles · Mar 4, 2012
Engine And Engine Cooling
THE COOLANT LINE CONNECTORS THAT COME OUT OF THE ENGINE / BLOCK ARE DISLODGING FROM THE ENGINE BLOCKS AND BLOWING OUT ALL OF THE COOLANT IN A MATTER OF SECONDS. PORSCHE USED SOME SORT OF ADHESIVE TO HOLD THE CONNECTORS IN THE BLOCK INSTEAD OF WELDING THEM IN; AS THE CARS AGE AND GO THROUGH LOTS OF HEAT CYCLES, THE ADHESIVE IS WE…
Read full complaint
THE COOLANT LINE CONNECTORS THAT COME OUT OF THE ENGINE / BLOCK ARE DISLODGING FROM THE ENGINE BLOCKS AND BLOWING OUT ALL OF THE COOLANT IN A MATTER OF SECONDS. PORSCHE USED SOME SORT OF ADHESIVE TO HOLD THE CONNECTORS IN THE BLOCK INSTEAD OF WELDING THEM IN; AS THE CARS AGE AND GO THROUGH LOTS OF HEAT CYCLES, THE ADHESIVE IS WEARING OUT AND THE CONNECTORS ARE BLOWING OUT OF THE ENGINE BLOCK CAUSING A MASSIVE COOLANT DUMP WHICH CAN BE DANGEROUS IF TRAVELING AT FREEWAY SPEEDS. *TR
CERTAIN PASSENGER VEHICLES FITTED WITH FRONT SEAT BACKS, WHICH DO NOT MEET PORSCHE'S STRENGTH STANDARDS.
Consequence & remedy
Consequence: IN THE EVENT OF A VEHICLE CRASH, THE SEATS COULD TWIST, TILTING ON ONE SIDE TO THE REAR, POSSIBLY RESULTING IN PERSONAL INJURY TO THE VEHICLE OCCUPANT.
Remedy: DEALERS WILL REPLACE BOTH THE FRONT SEATS. OWNER NOTIFICATION BEGAN ON APRIL 26, 2004. OWNERS SHOULD CONTACT PORSCHE AT 1-800-545-8039.
CERTAIN PASSENGER VEHICLES MAY HAVE A LOOSE FITTING IN THE PRESSURE LINE OF THE POWER STEERING ASSEMBLY.
Consequence & remedy
Consequence: IF THE FITTING IS LOOSE, THE HYDRAULIC FLUID COULD LEAK OUT, WHICH COULD LEAD TO LOSS OF POWER STEERING ASSIST AND, FOR VEHICLES EQUIPPED WITH A MANUAL TRANSMISSION, LOSS OF CLUTCH ASSISTANCE. IF THE LEAKING FLUID COMES INTO CONTACT WITH HOT EXHAUST COMPONENTS, IT COULD IGNITE.
Remedy: DEALERS WILL TIGHTEN THE FITTING TO SPECIFICATIONS. OWNER NOTIFICATION BEGAN ON DECEMBER 1, 2003. OWNERS SHOULD CONTACT PORSCHE AT 1-800-545-8039.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
2003 Porsche 911 Turbo Problems, Complaints & Recalls | Skip That Year
Illustration