I HAVE BEEN INFORMED BY MY PORSCHE TECHNICIAN THAT PORSCHE USED AN INFERIOR AND MECHANICALLY POOR DESIGN FOR THE ENGINE COOLANT LINES. THEY ARE GLUED TOGETHER IN A PLACE WHERE THEY GET HOT. AFTER SEVERAL HEAT CYCLES, THEY WILL FAIL. ALL CARS WITH THIS ENGINE DESIGN WILL HAVE THIS FAILURE OVER TIME. IF THE COOLANT LINES FAIL WHIL…
Read full complaint
I HAVE BEEN INFORMED BY MY PORSCHE TECHNICIAN THAT PORSCHE USED AN INFERIOR AND MECHANICALLY POOR DESIGN FOR THE ENGINE COOLANT LINES. THEY ARE GLUED TOGETHER IN A PLACE WHERE THEY GET HOT. AFTER SEVERAL HEAT CYCLES, THEY WILL FAIL. ALL CARS WITH THIS ENGINE DESIGN WILL HAVE THIS FAILURE OVER TIME. IF THE COOLANT LINES FAIL WHILE THE CAR IS MOVING, THE SLICK COOLANT CAN GET ON THE TIRES AND CAUSE AN ACCIDENT. ALSO, THE ENGINE CAN OVERHEAT WITH A REPLACEMENT COST OF OVER $20,000. PORSCHE IS AWARE OF THIS, AS THEY HAVE USED A SUPERIOR THREADED DESIGN ON THEIR RACE CARS WITH THIS ENGINE. I HAVE BEEN ADVISED THAT THIS WILL TAKE THOUSANDS OF DOLLARS TO FIX, AND THE CAR WILL BE OUT OF SERVICE FOR WEEKS. *TR
NHTSA ODI #10514700
48,000 miles · Jun 2, 2013
EnginePower Train
MY MECHANIC INFORMED ME THAT PORSCHE USED AN INFERIOR AND MECHANICALLY POOR DESIGN FOR THE ENGINE COOLANT LINES. THEY ARE GLUED TOGETHER IN A PLACE WHERE THEY GET HOT. AFTER SEVERAL HEAT CYCLES, THEY WILL FAIL. ALL CARS WITH THIS ENGINE DESIGN WILL HAVE THIS FAILURE OVER TIME. IF THE COOLANT LINES FAIL WHILE THE CAR IS MOVING, T…
Read full complaint
MY MECHANIC INFORMED ME THAT PORSCHE USED AN INFERIOR AND MECHANICALLY POOR DESIGN FOR THE ENGINE COOLANT LINES. THEY ARE GLUED TOGETHER IN A PLACE WHERE THEY GET HOT. AFTER SEVERAL HEAT CYCLES, THEY WILL FAIL. ALL CARS WITH THIS ENGINE DESIGN WILL HAVE THIS FAILURE OVER TIME. IF THE COOLANT LINES FAIL WHILE THE CAR IS MOVING, THE SLICK COOLANT CAN GET ON THE TIRES AND CAUSE AN ACCIDENT. ALSO, THE ENGINE CAN OVERHEAT WITH A REPLACEMENT COST OF OVER $20,000. PORSCHE IS AWARE OF THIS, AS THEY HAVE USES A SUPERIOR THREADED DESIGN ON THEIR RACE CARS WITH THIS ENGINE. I HAVE BEEN ADVISED THAT THIS WILL TAKE THOUSANDS OF DOLLARS TO FIX, AND THE CAR WILL BE OUT OF SERVICE FOR WEEKS. *TR
NHTSA ODI #10514698
23,910 miles · May 2, 2013
EnginePower Train
I WAS DRIVING THE CAR WHEN SUDDENLY THE LOW COOLANT LIGHT CAME ON. INSTANTLY, TEMPERATURE STARTED RISING AND I SHUT IT DOWN. I WASN'T SURE WHAT WAS WRONG BUT I FOUND COOLANT ALL OVER THE REAR WHEELS AND TIRES. AFTER SITTING ON SIDE OF ROAD, ANOTHER PORSCHE OWNER STOPPED BY. WE THOUGHT THE CAR WAS JUST OVERHEATING, SO WE ADDE…
Read full complaint
I WAS DRIVING THE CAR WHEN SUDDENLY THE LOW COOLANT LIGHT CAME ON. INSTANTLY, TEMPERATURE STARTED RISING AND I SHUT IT DOWN. I WASN'T SURE WHAT WAS WRONG BUT I FOUND COOLANT ALL OVER THE REAR WHEELS AND TIRES. AFTER SITTING ON SIDE OF ROAD, ANOTHER PORSCHE OWNER STOPPED BY. WE THOUGHT THE CAR WAS JUST OVERHEATING, SO WE ADDED WATER. IT SEEMED FINE SO I STARTED DRIVING HOME AND THEN IT HAPPENED AGAIN. WE PUT THE CAR ON MY BUDDY'S LIFT AND IDENTIFIED THAT THE COOLANT WAS LEAKING FROM THE TOP OF THE MOTOR. AFTER DOING SOME RESEARCH AND TALKING TO MY MECHANIC, IT APPEARS THAT THE COOLANT HOSES THAT ARE BONDED TO THE EXCHANGER HAVE SEPARATED. APPARENTLY, THE HOSE IS GLUED TO THE FITTING. THEY ARE BOTH METAL. MY MECHANIC IS STILL TRYING TO IDENTIFY A PERMANENT FIX BUT AS OF YET WE HAVEN'T FIXED IT. I AM WAITING A BIT TO FIGURE OUT THE BEST WAY TO FIX THE CAR TO AVOID FUTURE FAILURE. THE CAR HAS LOW MILES AND I AM CONCERNED AFTER DOING SOME RESEARCH THAT IT COULD HAPPEN AGAIN. *TR
NHTSA ODI #10510343
30,000 miles · Nov 2, 2007
Power Train
AT ABOUT 30,000 MILES, THE TRANSMISSION IN MY 2001 PORSCHE 911 TURBO BEGAN POPPING OUT OF SECOND GEAR UPON DECELERATION. PORSCHE IS AWARE OF THIS PROBLEM IN THE MANUAL TRANSMISSIONS IN THESE CARS, AND EVEN HAS A TECHNICAL BULLETIN OUT THAT STATES IT MIGHT BE BECAUSE OF ASSEMBLY DEFECTS. CERTAINLY, THE BRASS SYNCHROS IN THE TRA…
Read full complaint
AT ABOUT 30,000 MILES, THE TRANSMISSION IN MY 2001 PORSCHE 911 TURBO BEGAN POPPING OUT OF SECOND GEAR UPON DECELERATION. PORSCHE IS AWARE OF THIS PROBLEM IN THE MANUAL TRANSMISSIONS IN THESE CARS, AND EVEN HAS A TECHNICAL BULLETIN OUT THAT STATES IT MIGHT BE BECAUSE OF ASSEMBLY DEFECTS. CERTAINLY, THE BRASS SYNCHROS IN THE TRANSMISSION ARE VERY WEAK AND PRONE TO FAILURE. THIS IS UNACCEPTABLE IN SUCH AN EXPENSIVE AND POWERFUL CAR. PORSCHE HAS TAKEN NO RESPONSIBILITY FOR THIS AND CHARGES UPWARDS OF $5000 FOR A NEW TRANSMISSION. THIS IS A SEVERE SAFETY HAZARD BECAUSE THE DRIVING CHARACTERISTICS OF THE CAR CHANGE DRAMATICALLY WHEN YOU ARE SLOWING DOWN, ESPECIALLY IF TURNING A CORNER AT THE SAME TIME. *TR
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH MANUAL TRANSMISSIONS. IT IS POSSIBLE THAT THE CLUTCH PRESSURE LINE COULD LEAK IN THE AREA OF ITS CONNECTION WITH THE CLUTCH CYLINDER.
Consequence & remedy
Consequence: A REDUCTION, OR COMPLETE LOSS, OF THE CLUTCH AND STEERING POWER ASSISTANCE COULD RESULT. IF LEAKING FLUID CONTACTS THE EXHAUST SYSTEM, THERE IS A RISK OF FIRE.
Remedy: DEALERS WILL REPLACE THE CLUTCH PRESSURE LINE AND AN ADDITIONAL SUPPORTING BRACKET WILL BE INSTALLED ON VEHICLES PRODUCED BEFORE OCTOBER 13, 2000. VEHICLES PRODUCED AFTER OCTOBER 13, 2000 HAS A NEW TYPE OF CLUTCH PRESSURE LINE. ON VEHICLES PRODUCED BETWEEN OCTOBER 13 AND NOVEMBER 28, 2000, AN ADDITIONAL SUPPORTING BRACKET WILL BE INSTALLED. OWNER NOTIFICATION BEGAN FEBRUARY 1, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT PORSCHE AT 1-800-545-8039.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. IT IS POSSIBLE THAT THE FUEL SUPPLY LINE COULD LEAK DUE TO CHAFFING WITH THE INTAKE MANIFOLD AND/OR THE FUEL RETURN LINE COULD LEAK DUE TO CHAFFING WITH A SPRING BAND CLAMP USED TO SECURE A COOLANT LINE.
Consequence & remedy
Consequence: THE LEAKING FUEL COULD COME INTO CONTACT WITH THE EXHAUST SYSTEM, INCREASING THE RISK OF A FIRE.
Remedy: DEALERS WILL INSTALL A PROTECTIVE SHEATH ON THE FUEL SUPPLY LINE. IN ADDITION, FOR VEHICLES PRODUCED BETWEEN APRIL 7 AND MAY 22, 2000, THE SPRING BAND CLAMP WILL BE REPLACED WITH A SCREW TYPE HOSE CLAMP AND INSTALLED IN SUCH A WAY THAT IT CANNOT COME INTO CONTACT WITH THE FUEL RETURN LINE. OWNER NOTIFICATION BEGAN FEBRUARY 1, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT PORSCHE AT 1-800-545-8039.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
2001 Porsche 911 Turbo Problems, Complaints & Recalls | Skip That Year
Illustration