PROBLEM SIMILAR TO CASE PE13009 INCIDENTS OF SUDDEN COOLANT LOSS WHICH OCCURRED WHILE DRIVING ON PUBLIC ROADWAYS WELL UNDER HIGHWAY SPEED LIMIT (LESS THAN 60MPH). THE PROBLEM OCCUR SUDDEN WITH NO WAY TO AVOID AND CHECK PRIOR INCIDENT HAPPEN. THIS COULD CAUSE HUGE ISSUE TO OTHER MOTORWAY DRIVERS AND I HOPE PORSCHE USA CAN BE R…
Read full complaint
PROBLEM SIMILAR TO CASE PE13009 INCIDENTS OF SUDDEN COOLANT LOSS WHICH OCCURRED WHILE DRIVING ON PUBLIC ROADWAYS WELL UNDER HIGHWAY SPEED LIMIT (LESS THAN 60MPH). THE PROBLEM OCCUR SUDDEN WITH NO WAY TO AVOID AND CHECK PRIOR INCIDENT HAPPEN. THIS COULD CAUSE HUGE ISSUE TO OTHER MOTORWAY DRIVERS AND I HOPE PORSCHE USA CAN BE RESPONSIBLE FOR THIS. *TR
NHTSA ODI #10511547
44,000 miles · Oct 31, 2011
Engine And Engine Cooling
WATER MANIFOLD HAS PRESS-FIT EPOYY CONNECTIONS THAT HAVE BEEN KNOWN TO COME LOOSE. MINE DID AND I LOST ALL OF MY COOLANT. IT BLEW ACROSS THE WHOLE ENGINE BAY AND OVER BACK TIRES. VERY DANGEROUS AS A CAR SPUN OUT OF CONTROL BEHIND ME AS WELL. TOOK ENGINE APART AND WELDED TWO OF THE FITTINGS BUT SEVERAL OTHERS REMAIN OEM. EXPE…
Read full complaint
WATER MANIFOLD HAS PRESS-FIT EPOYY CONNECTIONS THAT HAVE BEEN KNOWN TO COME LOOSE. MINE DID AND I LOST ALL OF MY COOLANT. IT BLEW ACROSS THE WHOLE ENGINE BAY AND OVER BACK TIRES. VERY DANGEROUS AS A CAR SPUN OUT OF CONTROL BEHIND ME AS WELL. TOOK ENGINE APART AND WELDED TWO OF THE FITTINGS BUT SEVERAL OTHERS REMAIN OEM. EXPENSIVE FIX THUS FAR, AND NOT YET DONE. VERY POOR DESIGN AND DANGEROUS!! *TR
NHTSA ODI #10433654
67,500 miles · Oct 31, 2011
Engine And Engine Cooling
SUDDEN, CATASTROPHIC FAILURE OF COOLANT HOSE 996.106.502.74 BY LONGITUDINAL SPLIT APPROXIMATELY 4" LONG. COOLANT DUMPED ON LR WHEEL CAUSED LOSS OF CONTROL AND VEHICLE SPIN. *TR
VEHICLE DESCRIPTION: PASSENGER VEHICLES EQUIPPED WITH MANUAL TRANSMISSIONS. IT IS POSSIBLE THAT THE CLUTCH PRESSURE LINE COULD LEAK IN THE AREA OF ITS CONNECTION WITH THE CLUTCH CYLINDER.
Consequence & remedy
Consequence: A REDUCTION, OR COMPLETE LOSS, OF THE CLUTCH AND STEERING POWER ASSISTANCE COULD RESULT. IF LEAKING FLUID CONTACTS THE EXHAUST SYSTEM, THERE IS A RISK OF FIRE.
Remedy: DEALERS WILL REPLACE THE CLUTCH PRESSURE LINE AND AN ADDITIONAL SUPPORTING BRACKET WILL BE INSTALLED ON VEHICLES PRODUCED BEFORE OCTOBER 13, 2000. VEHICLES PRODUCED AFTER OCTOBER 13, 2000 HAS A NEW TYPE OF CLUTCH PRESSURE LINE. ON VEHICLES PRODUCED BETWEEN OCTOBER 13 AND NOVEMBER 28, 2000, AN ADDITIONAL SUPPORTING BRACKET WILL BE INSTALLED. OWNER NOTIFICATION BEGAN FEBRUARY 1, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT PORSCHE AT 1-800-545-8039.
VEHICLE DESCRIPTION: PASSENGER VEHICLES. IT IS POSSIBLE THAT THE FUEL SUPPLY LINE COULD LEAK DUE TO CHAFFING WITH THE INTAKE MANIFOLD AND/OR THE FUEL RETURN LINE COULD LEAK DUE TO CHAFFING WITH A SPRING BAND CLAMP USED TO SECURE A COOLANT LINE.
Consequence & remedy
Consequence: THE LEAKING FUEL COULD COME INTO CONTACT WITH THE EXHAUST SYSTEM, INCREASING THE RISK OF A FIRE.
Remedy: DEALERS WILL INSTALL A PROTECTIVE SHEATH ON THE FUEL SUPPLY LINE. IN ADDITION, FOR VEHICLES PRODUCED BETWEEN APRIL 7 AND MAY 22, 2000, THE SPRING BAND CLAMP WILL BE REPLACED WITH A SCREW TYPE HOSE CLAMP AND INSTALLED IN SUCH A WAY THAT IT CANNOT COME INTO CONTACT WITH THE FUEL RETURN LINE. OWNER NOTIFICATION BEGAN FEBRUARY 1, 2001. OWNERS WHO TAKE THEIR VEHICLES TO AN AUTHORIZED DEALER ON AN AGREED UPON SERVICE DATE AND DO NOT RECEIVE THE FREE REMEDY WITHIN A REASONABLE TIME SHOULD CONTACT PORSCHE AT 1-800-545-8039.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1
PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
2001 Porsche 911 Turbo Problems, Complaints & Recalls | Skip That Year
Illustration