IllustrationCOOLING FITTING FAILURE ON PORSCHE 911 GT3 RS 2007 WITH GLUED IN FITTINGS. *TR
2007 Porsche 911 GT3
Owner reports · Recalls · Investigations
Limited comparison data
There is not enough comparable history to draw a useful model-year comparison.
About this comparison →How this year compares
Owner complaints by model year
Compare all 911 GT3 years →Counts vary with age, sales and reporting. They are not failure rates.
What owners reported most
Tap a category to read its complaints. One report may name several components.
When problems were reported
Mileage at the reported incident
Limited mileage data: 19 of 24 reports include usable mileage. There isn’t enough coverage to show a useful chart.
NHTSA’s mileage field refers to the reported incident, not necessarily the filing date. This shows report counts, not the likelihood of a failure.
What to inspect
Issues worth paying extra attention to based on owner reports.
- Engine. Review the 20 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Engine And Engine Cooling. Review the 4 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
- Steering. Review the 1 owner reports in this category and discuss these concerns during a pre-purchase inspection. Read reports →
NHTSA owner reports · September 18, 2026 snapshot.
0 crash reports0 fire reports0 injury reports
Engine And Engine Cooling complaints
4 reportsDRIVING A 2007 PORSCHE GT3 WHEN A HOSE FITTING CAME LOOSE FROM THE ENGINE BLOCK CAUSING A CATASTROPHIC LOSS OF COOLANT FROM THE ENGINE. THE FAILURE CAN OCCUR MULTIPLE TIMES I HAVE BEEN TOLD BY OTHER OWNERS OF 996 AND 997 MODEL PORSCHE 911 MODEL VARIANTS. OCCURS IN ALL MODELS (CARRERA, TURBO, GT3, GT3RS) AS NOTED HERE: HTTP://…
Read full complaint
DRIVING A 2007 PORSCHE GT3 WHEN A HOSE FITTING CAME LOOSE FROM THE ENGINE BLOCK CAUSING A CATASTROPHIC LOSS OF COOLANT FROM THE ENGINE. THE FAILURE CAN OCCUR MULTIPLE TIMES I HAVE BEEN TOLD BY OTHER OWNERS OF 996 AND 997 MODEL PORSCHE 911 MODEL VARIANTS. OCCURS IN ALL MODELS (CARRERA, TURBO, GT3, GT3RS) AS NOTED HERE: HTTP://FORUMS.RENNLIST.COM/RENNFORUMS/SHOWTHREAD.PHP?T=592328&GOTO=NEWPOST. CONSEQUENCES ARE DUMPING OF ANTIFREEZE ON THE ROADWAY WHICH HAS A POTENTIAL TO CAUSE AN ACCIDENT. MY CAR WAS FIXED BY PORSCHE UNDER WARRANTY. PORSCHE REPLACED FITTINGS IN THE BLOCK WHICH WERE EPOXIED IN AS WERE THE ORIGINAL FITTINGS. A MORE PERMANENT SOLUTION SHOULD BE REQUIRED, SUCH AS WELDING OR PINNING OF THE FITTINGS INTO THE ENGINE CASE. OLD PARTS ARE NOT AVAILABLE AS PORSCHE WILL NOT TURN OVER ANY PARTS REPLACED UNDER WARRANTY. *KB
VEHICLE HAD COMPLETE LOSS OF CONTROL DUE TO A COOLING SYSTEM FITTING COMING UNGLUED FROM THE ENGINE BLOCK. THE COOLANT FITTING IS PRESS FITTED INTO PLACE USING AN ADHESIVE THAT FAILED. THE ENTIRE CONTENTS OF THE COOLING SYSTEM RELEASED ONTO THE REAR TIRES CAUSING A LOSS OF CONTROL. *TR
COOLANT FITTING ADHESIVE FAILED, SPRAYING COOLANT ON REAR TIRES, WHICH CAUSED THE VEHICLE TO LOSE CONTROL. FITTING WAS REPLACED UNDER WARRANTY WITH THE SAME PROBLEMATIC ADHESIVE. MULTIPLE FAILURES HAVE BEEN NOTED IN PORSCHE FORUMS AND A RECENTLY PUBLISHED ARTICLE IN A GLOBAL MAGAZINE NOTED THIS ISSUE HAS BEEN AROUND FOR SEVERAL …
Read full complaint
COOLANT FITTING ADHESIVE FAILED, SPRAYING COOLANT ON REAR TIRES, WHICH CAUSED THE VEHICLE TO LOSE CONTROL. FITTING WAS REPLACED UNDER WARRANTY WITH THE SAME PROBLEMATIC ADHESIVE. MULTIPLE FAILURES HAVE BEEN NOTED IN PORSCHE FORUMS AND A RECENTLY PUBLISHED ARTICLE IN A GLOBAL MAGAZINE NOTED THIS ISSUE HAS BEEN AROUND FOR SEVERAL YEARS WITH THIS ENGINE TYPE, WITH NO RESOLUTION FROM PORSCHE. *LN
Official recalls
0No recalls in this snapshot.
Model-level recall history does not show whether a particular VIN is affected or has received a repair. Check a VIN with NHTSA ↗
NHTSA investigations
1PE13009 · Rapid Coolant Loss
Opened Apr 26, 2013 · Closed Mar 10, 2014
Status: closed (inferred from source dates) · Engine And Engine Cooling; Engine And Engine Cooling:cooling System; Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Additional source detail variants (3)
Engine And Engine Cooling:cooling System:hoses/lines/piping/fittings
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling:cooling System
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.
Engine And Engine Cooling
On April 26, 2013, the Office of Defects Investigation (ODI) opened PE13-009 to investigate 10 complaints alleging incidents of sudden coolant loss while traveling on public roadways in certain model year (MY) 2001 through 2007 Porsche 911 vehicles.The complaints alleged that pipe ends joined by epoxy to certain cooling system components may fail suddenly and separate, resulting in large volumes of coolant leakage.The investigation was opened to assess evidence of a design or manufacturing defect in the coolant pipe fittings and any related safety consequences. In response to ODI?s Information Request letter, Porsche identified a manufacturing quality issue with the supplier?s application of adhesive to coolant pipe fittings that resulted in elevated failure rates in approximately 6,800 early production 997 generation vehicles (MY 2007 and early MY 2008).ODI?s analysis of field data showed that the age-adjusted failure rate for these vehicles was approximately six times greater than MY 2001 through 2005 996 generation vehicles and MY 2008 through 2011 997 generation vehicles built after a process improvement for adhesive application was implemented by the supplier.Most of the leak complaints reviewed by ODI did not appear to involve complete separation of the fittings and many were detected when the vehicle was parked.There were no crashes or injuries reported to be related to the alleged defect in any of the subject vehicles.ODI identified two allegations that coolant leakage resulted in loss of control incidents, but neither involved vehicles affected by the assembly process quality issue.A third loss of control allegation involving a vehicle built during the period affected by the supplier process concern is not counted since ODI was unable to contact the owner to confirm the incident.See the full closing resume in the document file for PE13-009 for additional information about the subject cooling system and ODI?s analysis of field data related to the alleged defect. A safety-related defect has not been identified at this time and further use of agency resources does not appear to be warranted.Accordingly, this investigation is closed.The closing of this investigation does not constitute a finding by NHTSA that a safety-related defect does not exist.The agency will monitor this issue and reserves the right to take further action if warranted by the circumstances.