NHTSA owner reports · September 18, 2026 snapshot.
Vehicle Speed Control complaints
21 reportsClear category filterMileage unknown · Dec 14, 2025
Electrical SystemVehicle Speed Control
My skid mark symbol comes on, does not go off until 2or 3 days later. My Nissan will not accelerate over 20 miles per hour. I have had mu vehicle checked several times at the Grainger Nissan dealership several times within the past 4 years after they installed a new transmission. They found and corrected other issues, but not wh…
Read full complaint
My skid mark symbol comes on, does not go off until 2or 3 days later. My Nissan will not accelerate over 20 miles per hour. I have had mu vehicle checked several times at the Grainger Nissan dealership several times within the past 4 years after they installed a new transmission. They found and corrected other issues, but not what causes the traction lights to come on and decrease speed causing me to have to use flashers and bike lanes where ever available until I get home. Independent mechanics have checked, knocked off traction light. It only comes on again. I have another mechanic at Precision Tune to check it out tomorrow. The last date of this occurrence was 12/ 08/2025
NHTSA ODI #11704982
Mileage unknown · Aug 3, 2020
Electrical SystemSuspensionVehicle Speed Control
THE ENGINE LIGHT DOESN'T TURN OFF AND THE COMPUTER SAYS ELECTRONICAL REASON . THE SPEED IS LOW
NHTSA ODI #11343019
47,555 miles · Jun 3, 2020
Fuel/propulsion SystemPower TrainUnknown Or Other
THE CAR DON'T RUNS GOOD!, HAVE PROBLEMS WITH THE TRANSMISSION ONLY HAVE 47,677 MILES, O THINK HAVE WARRANTY! *TR
NHTSA ODI #11327041
110,000 miles · Mar 19, 2020
Electrical SystemSuspensionVehicle Speed Control
THE CHECK ENGINE LIGHT COMES ON AND THE CODES COME UP SAYING IT'S THE SPEED SENSOR THE ABS LIGHT COMES ON THE CAR USER BRAKE FLUID TOO MUCH THE SHOCK ON PASSAGES SIDE IS TOTALLY OUT IT WAS DRIVING
NHTSA ODI #11318657
Mileage unknown · Jun 16, 2019
Electrical SystemService BrakesVehicle Speed Control
WHENEVER I STEP ON THE BRAKES SLOWLY THE CAR WANTS TO TURN OFF. IT PUSHES ITSELF. ALSO WHEN I STEP ON THE GAS IT LAGS TO SPEED UP.
NHTSA ODI #11220388
Mileage unknown · Jan 4, 2019
Power TrainService BrakesVehicle Speed Control
WHEN I FIRST PURCHASE THE NISSAN VERSA 2015 IN SEPT. 2015, THE CAR WAS USED IT HAD 15,000 MILES ON IT. I TEST DROVE IT A LITTLE BIT WHEN I TRIED TO DRIVE IT OFF I NOTICED THE TRANSMISSION WAS ACTING UP BEFORE I GOT OFF THE STOCKTON DEALERSHIP. I BROUGHT IT BACK AND THEY TEST DROVE IT. THEY SAID YES THERE IS SOMETHING WRONG AND R…
Read full complaint
WHEN I FIRST PURCHASE THE NISSAN VERSA 2015 IN SEPT. 2015, THE CAR WAS USED IT HAD 15,000 MILES ON IT. I TEST DROVE IT A LITTLE BIT WHEN I TRIED TO DRIVE IT OFF I NOTICED THE TRANSMISSION WAS ACTING UP BEFORE I GOT OFF THE STOCKTON DEALERSHIP. I BROUGHT IT BACK AND THEY TEST DROVE IT. THEY SAID YES THERE IS SOMETHING WRONG AND REPLACE IT. NOW, I AM THINKING BACK, THE DEALERSHIP KNEW THE TRANSMISSION WAS NOT WORKING CORRECTLY. BEFORE I PURCHASED THE CAR. THE DEALERSHIP CONVINCED ME TO GET THE EXTENDED WARRANTY. I AM THINKING WHY IS A BRAND NEW CAR WITH 15,000 MILES ON IT.. SO, IT TOOK ABOUT A MONTH TO REPLACE THE TRANSMISSION AND IT DROVE OK. THEN IN 2017, I NOTICED A SMALL SLIPPING NOISE, LIKE A SMALL DRUMROLL EVERY NOW AND THEN. THEN FINALLY I TOOK THE CAR TO OAKLAND DEALERSHIP IN 2017 AROUND 88,000 MILES. THEY COULDN'T LOCATE THE TRANSMISSION PROBLEM OR NOISE. IN A FEW DAYS, I PICK UP THE CAR AND AS SOON AS I DROVE IT I HEAR THE SLIPPING DRUMROLL SOUND. I TOOK IT BACK AND THE DEALERSHIP SAID WE TESTED AND THE TRANSMISSION WAS FINE. I WAS DISCOURAGED WITH THE RESULTS, NOW IT JAN 2019, MANY MONTHS LATER, AND TRANSMISSION SLIPPING AND EXPIRED WARRANTY. THE TRANSMISSION SLIPPING, MORE FREQUENT LOUD DRUMROLL NOISE AND SHAKING WHILE TRYING TO ACCELERATE THE CAR. I LOOKED IT UP ON GOOGLE AND I NOTICED THAT NISSAN DOUBLED THE EXTENDED WARRANTY ON THEIR TRANSMISSION. TODAY, I WENT TO THE OAKLAND DEALERSHIP AND THEY SAID MY NISSAN VERSA IS NOT UNDER THAT EXTENDED WARRANTY. HOW CAN THIS BE? THERE ARE HUNDREDS OF COMPLAINTS AND FAILURES ABOUT THE NISSAN TRANSMISSION. NISSAN AND DEALERSHIP KNEW ABOUT THE TRANSMISSION FAILURE IN THE VERSA. RIGHT NOW, I FEEL THE CAR IS UNSAFE TO DRIVE ON THE STREET BECAUSE THE TRANSMISSION WILL FAIL AN ANY GIVEN TIME AND DRIVING CONDITION. PLEASE RECALL ALL NISSAN VERSA AND HAVE THE COMPANY FIX THIS RECURRING TRANSMISSION ISSUE.
NHTSA ODI #11165851
45,000 miles · Dec 23, 2018
Fuel/propulsion SystemPower TrainVehicle Speed Control
ON BOTH CITY STREETS AND HIGHWAYS. ACCELERATOR WILL STICK AND OR CLUTCH IS NOT PROPERLY ENGAGING AS SPECIFIC VEHICLE HAS A MANUAL TRANSMISSION. CAUSING THE VEHICLES RPM TO GO UP HIGHER THEN RECOMMENDED.
NHTSA ODI #11163198
Mileage unknown · Aug 1, 2018
Electrical SystemVehicle Speed ControlVisibility
2015 NISSAN VERSA SV. CONSUMER WRITES IN REGARDS TO SEVERAL DESIGN DEFECTS ON VEHICLE. *LD THE CONSUMER STATED THE ELECTRONIC KEY HOLD WAS EXTREMELY SENSITIVE CAUSING THE TRUNK LID TO OPEN INADVERTENTLY. THE GAS PEDAL SEEMS TO STICK CAUSING THE ENGINE TO REV. THE VEHICLE HAS AN INTENSE WOBBLE CAUSING A NAUSEATING SENSATION. T…
Read full complaint
2015 NISSAN VERSA SV. CONSUMER WRITES IN REGARDS TO SEVERAL DESIGN DEFECTS ON VEHICLE. *LD THE CONSUMER STATED THE ELECTRONIC KEY HOLD WAS EXTREMELY SENSITIVE CAUSING THE TRUNK LID TO OPEN INADVERTENTLY. THE GAS PEDAL SEEMS TO STICK CAUSING THE ENGINE TO REV. THE VEHICLE HAS AN INTENSE WOBBLE CAUSING A NAUSEATING SENSATION. THE CHROME AROUND THE SPEEDOMETER AND DASHBOARD REFLECTION CAUSES A VISIBILITY ISSUE. THE CONSUMER WOULD INADVERTENTLY LEAVE THE KEY THE IGNITION AND MANUALLY LOCK THE DOOR, THUS LOCKING THE KEY IN THE CAR. THE CONSUMER SUGGESTED AN ALARM FOR SUCH OCCASIONS. THE VEHICLE HAS LOW FREQUENCY CONSTANT HUMMING FREQUENCY BASS LIKE DRONING NOISE THAT'S CENTERED IN THE MIDDLE OF THE DRIVER'S SEAT. *JS
NHTSA ODI #11112715
62,000 miles · Jul 23, 2018
EngineVehicle Speed Control
VEHICLE STALLS/HESITATES WHEN ACCELERATING IF ENGINE IS WARM. WILL RESTART IMMEDIATELY IF STALLS, BUT CONTINUED ATTEMPTS TO ACCELERATE RESULT IN HESITATION OR STALLING. THIS HAS OCCURRED IN TRAFFIC AS WELL AS FROM A COMPLETE STOP AFTER BEING PARKED, BUT STILL WARM.
NHTSA ODI #11113002
33,000 miles · May 7, 2018
Vehicle Speed ControlVisibility/wiper
I WAS DRIVING ON A HIGHWAY AT NIGHT WHEN A CAR WITH LIGHTS AS BRIGHT AS A FOOTBALL STADIUM CAME UP BEHIND ME. I COULD NO LONGER SEE THE ROAD IN FRONT OF ME AND HAD TO SLOW DOWN AND PULL OFF THE ROAD UNTIL THE CAR WENT AROUND ME. THIS WAS DANGEROUS AND COULD HAVE CAUSED A HORRIFIC ACCIDENT WITH POSSIBLE DEATHS.
NHTSA ODI #11092371
NHTSA investigations
2EA21002 · Desiccated Air Bag Inflator Rupture
Opened Sep 17, 2021 · No close date supplied
Status: open (inferred from source dates) · Air Bags:frontal:driver Side:inflator Module; Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Additional source detail variants (2)
Air Bags:frontal:driver Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
Air Bags:frontal:passenger Side:inflator Module
From 2000 through 2017, Takata produced millions of air bag inflators using two types of phase-stabilized ammonium nitrate ("PSAN") propellant -- propellant 2004 and propellant 2004L. After prolonged exposure to high temperature cycles and humidity, inflators using propellant 2004 can degrade, causing the propellant to burn too quickly when ignited. The rapid burning can cause the inflator to rupture during deployment, potentially causing serious or even fatal injury to vehicle occupants. See 2016 Blomquist Report at www.nhtsa.gov/sites/nhtsa.gov/files/documents/expert_report-hrblomquist.pdf.Consequently, all frontal inflators using propellant 2004 that do not contain a "desiccant" (a substance that traps and holds moisture) in US vehicles are under recall. These "non-desiccated" inflators either have been or are required to be replaced.In some cases, the remedy part for these recalled inflators was, or will be, an inflator using either propellant 2004 or 2004L that does contain a desiccant. None of these "desiccated" remedy parts (which were installed in older model year vehicles) are currently under recall for a degradation concern. Certain subsets of desiccated PSAN inflators using propellant 2004 for use as original equipment, however, have been recalled for a degradation concern. All Takata inflators produced with propellant 2004L contain desiccant, and none of these desiccated inflators using propellant 2004L are under recall for a degradation concern. There have been no reported field ruptures in any non-recalled desiccated PSAN inflators.It is understood that desiccants fully saturate at some threshold, at which point any additional moisture will not be captured. This means the degradation process observed in non-desiccated inflators using propellant 2004 may also occur in non-recalled desiccated inflators using propellant 2004, assuming additional moisture enters the inflator and high temperature cycling occurs. Based on available information, desiccant saturation can occur within the first five years in the worst environments, and the time required for full saturation is affected by multiple factors. While no present safety risk has been identified, further work is needed to evaluate the future risk of non-recalled desiccated inflators using propellant 2004.Three entities -- Takata (now known as TK Global), the Independent Testing Coalition, and Exponent -- have been studying the long-term behavior of Takata desiccated PSAN inflators using propellant 2004L (as well as 2004) in the presence of moisture and temperature cycling. The research efforts, which include development of predictive modeling techniques and field sample analysis, are ongoing. To date, none of the researchers have identified field evidence showing that propellant 2004L is undergoing a degradation process that leads to aggressive deployment and potential rupture. However, the time in service of such inflators remains short compared to that of the inflators using propellant 2004. Further study is needed to assess the long-term safety of desiccated inflators using propellant 2004L.The Office of Defects Investigation is opening this investigation to examine whether a safety defect related to propellant degradation exists in non-recalled desiccated PSAN frontal inflators manufactured by Takata. This investigation will require extensive information on Takata production processes and surveys of inflators in the field. Lists of recall actions that may have used desiccated PSAN inflators as remedy parts, as well as the makes and models originally manufactured with them, is available with the downloadable version of this document (see nhtsa.gov/recalls?nhtsaId=EA21002 -- note this information is subject to change/revision as the investigation proceeds). This investigation does not supersede EA15-001, which remains open.
EA15003 · Pedal Operation Interference
Opened Apr 1, 2015 · Closed Sep 1, 2015
Status: closed (inferred from source dates) · Service Brakes, Hydraulic; Service Brakes, Hydraulic:pedals And Linkages; Vehicle Speed Control:accelerator Pedal
On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obstructions in the subject vehicles identified 45 complaints, 7 crashes and 1 minor soft tissue injury.Thirty-five (35) of the complaints, all 7 crashes and the only injury were caused by the trim panel condition which is the subject of the recall.ODI will continue to monitor complaints related to the HVAC duct condition.This investigation is closed based on Nissan's recall.The VOQs associated with the closing of this investigation are: 10725339, 10723544, 10711794, 10691631, 10649259, 10640644, 10629161, 10614957, 10610356, 10606832, 10606766, 10606670, 10597004, 10573057, 10503811, and 10498000.
Additional source detail variants (3)
Service Brakes, Hydraulic
On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obstructions in the subject vehicles identified 45 complaints, 7 crashes and 1 minor soft tissue injury.Thirty-five (35) of the complaints, all 7 crashes and the only injury were caused by the trim panel condition which is the subject of the recall.ODI will continue to monitor complaints related to the HVAC duct condition.This investigation is closed based on Nissan's recall.The VOQs associated with the closing of this investigation are: 10725339, 10723544, 10711794, 10691631, 10649259, 10640644, 10629161, 10614957, 10610356, 10606832, 10606766, 10606670, 10597004, 10573057, 10503811, and 10498000.
Service Brakes, Hydraulic:pedals And Linkages
On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obstructions in the subject vehicles identified 45 complaints, 7 crashes and 1 minor soft tissue injury.Thirty-five (35) of the complaints, all 7 crashes and the only injury were caused by the trim panel condition which is the subject of the recall.ODI will continue to monitor complaints related to the HVAC duct condition.This investigation is closed based on Nissan's recall.The VOQs associated with the closing of this investigation are: 10725339, 10723544, 10711794, 10691631, 10649259, 10640644, 10629161, 10614957, 10610356, 10606832, 10606766, 10606670, 10597004, 10573057, 10503811, and 10498000.
Vehicle Speed Control:accelerator Pedal
On August 11, 2015, Nissan North America, Inc., submitted a Defect Information Report (DIR) describing a condition that may impede the driver's ability to transition quickly and smoothly from the accelerator pedal to the brake pedal in certain model year (MY) 2012 through 2015 Nissan Versa Sedans and MY 2014 through 2015 Nissan Versa Note vehicles (NHTSA Recall No. 15V-507).According to Nissan's DIR, in certain circumstances related to driver foot position and shoe type, the right edge of the driver?s shoe may catch the edge of the center console lower trim panel.Nissan indicated that this condition could cause a slight delay in the smooth transition between the accelerator pedal and the brake pedal which may increase the braking distance; therefore increasing the risk of a crash.Nissan's recall instructs dealers to trim the console panel so that the leading edge is at a greater distance from the driver?s foot.Nissan had previously issued a service campaign (Nissan Campaign ID #P5308; TSB #NTB15-033) on April 16, 2015, to provide the remedy for the same set of vehicles before deciding to change the program to a safety recall.Of the approximately 421,305 vehicles covered by recall 15V-507, approximately 122,558 have already been repaired under the service campaign. ODI's investigation also examined allegations that an HVAC duct in the driver's footwell area may interfere with the driver's right foot in certain circumstances.ODI's analysis of all complaints related to foot obstructions in the subject vehicles identified 45 complaints, 7 crashes and 1 minor soft tissue injury.Thirty-five (35) of the complaints, all 7 crashes and the only injury were caused by the trim panel condition which is the subject of the recall.ODI will continue to monitor complaints related to the HVAC duct condition.This investigation is closed based on Nissan's recall.The VOQs associated with the closing of this investigation are: 10725339, 10723544, 10711794, 10691631, 10649259, 10640644, 10629161, 10614957, 10610356, 10606832, 10606766, 10606670, 10597004, 10573057, 10503811, and 10498000.
Illustration